Double Deposition and Stripping Steps for Trace Determination of Au(III) Using Anodic Stripping Voltammetry

A new way of decreasing the detection limit ‐ double deposition and stripping steps was proposed to determine trace amounts of gold(III) by anodic stripping voltammetry. Two carbon composite electrodes that differed drastically in their surface areas were used for the measurements. The calibration graph was linear from 1×10^?9 to 1×10^?8 mol L^?1 following deposition time of 300 s at the first and the second electrode. The detection limit was found to be 2.3×10^?10 and 1.4×10^?11 mol L^?1 for deposition time 600 and 2400 s, respectively. It is the lowest detection limit obtained so far for gold(III) determination in stripping voltammetry.     

Sensitive Anodic Stripping Voltammetric Copper Ions Determination Performed in Double Deposition and Double Stripping Steps System for Real Water Samples Analysis

The article reports on utilization of double deposition and stripping steps for increasing sensitivity of Cu(II) determination by anodic stripping voltammetry (ASV) at two lead film working electrodes. A significant preconcentration of copper was achieved thanks to utilization of a simple design of four electrodes system that gives possibility to perform one measurement cycle consisting of two deposition and two stripping steps. Due to the fact that deposition step is doubled, the concentration of Pb(II) needed to lead film electrodes formation was significantly reduced as compared to traditional procedures using three electrodes system. The analytical procedure of Cu(II) determination was optimized. The experimental factors: supporting electrolyte's pH and its concentration, lead ions concentration, potential and time of deposition at both working electrodes were studied. The Cu(II) peak current was linearly dependent on its concentration from 5×10^?10 to 2×10^?8 mol L^?1 (deposition time of 270 and 160 s at the first and the second working electrode, respectively). The obtained detection limit for copper ions determination was 2.1×10^?10 mol L^?1. The described procedure was validated by analysis of two water certified reference materials. The described procedure was also utilized for real water sample analysis.     

Determination of cobalt by adsorptive stripping voltammetry with double accumulation and stripping steps

A double accumulation and stripping steps were proposed to increase the sensitivity of Co(II) determination by catalytic adsorptive stripping voltammetry (AdSV). Electrodes with large and small surface area were used for the first and second accumulation step, respectively. As the accumulation of Co(II) complex at the first electrode was finished, the electrode was placed at a short distance opposite the second one. Then the Co(II) complex desorbed from the first electrode was accumulated at the second electrode. Taking into account the small volume of space between the electrodes, the concentration of the Co(II) complex in solution between the electrodes was drastically higher than that in the bulk solution. The accumulation step at the second electrode was performed from the solution with higher concentration of Co(II) and therefore the detection limit was lowered. The calibration graph of Co(II) determination for accumulation time of 120 s at both electrodes was linear from 1.18 to 58.9 ng L^?1. The detection limit for Co(II) was equal to 0.47 ng L^?1 and it is so far the lowest detection limit obtained for Co(II) using mercury-free electrodes. The proposed method was applied to Co(II) determination in water certified reference material.     

The Use of the Bismuth Film Electrode for the Anodic Stripping Voltammetric Determination of Tin

Bismuth coated glassy carbon electrodes have been applied to the square‐wave anodic stripping voltammetry (SWASV) of trace concentrations of tin. Optimization of Bismuth Film Electrode (BFE) performance was conducted after initial comparison with the more traditional mercury electrode. Simultaneous deposition of tin and bismuth at ?1.3 V for 2 minutes in a supporting electrolyte of 2.5 M sodium bromide utilizing a square‐wave stripping step, allowed analysis of tin at the μg L^?1 level. Parameters, such as deposition potential and time, bismuth concentration, square‐waveform settings including amplitude, step height and frequency were studied and optimized. The dependence of stripping current on deposition time indicates that using longer deposition time should facilitate sub μg L^?1 analysis. Tin was analyzed simultaneously with cadmium and either indium or thallium; Where as lead and copper were not resolved from the stripping peaks of tin and bismuth respectively. Finally, the method was applied to the analysis of tin in fruit juice.     

Determination of Thallium in a Flow System by Anodic Stripping Voltammetry at a Bismuth Film Electrode

A procedure for trace thallium determination by anodic stripping voltammetry at a bismuth film electrode is presented. Measurements were performed in a flow system. The calibration graph was linear from 2×10^?9 to 3×10^?8 mol L^?1 for an accumulation time of 300 s. A detection limit for Tl⁺ following deposition time of 300 s was 6×10^?10 mol L^?1. The relative standard deviation at Tl⁺ concentration 2×10^?8 mol L^?1 was 3.9%. For determination of thallium in complex matrices the procedure for elimination of interferences from foreign ions exploiting anion exchange resin was proposed. The procedure proposed was validated by analysis of rain water certified reference material.     

Application of Square Wave Anodic Stripping Voltammetry for Determination of Traces of Ti(I) at Carbon Electrodes In Situ Modified with Bi Films

Bismuth films deposited in situ at glassy carbon and carbon film electrodes were tested for the determination of traces of Tl(I) separately and together with Zn(II) and Pb (II), in acetate buffer solution pH 3.7, using square wave anodic stripping voltammetry. Electrochemical impedance spectra in the presence of Tl(I) showed differences between the electrode substrates. The sensitivity to Tl does not depend on the presence of other ions, and was better at carbon film electrodes, although the 2 nmol L^?1 detection limit was independent of electrode substrate. Application to the measurement of Tl(I) in commercial berry juice is demonstrated.     

Determination of Vitamin K1by Adsorptive Stripping Square-Wave Voltammetry

Abstract

The adsorption of vitamin Ki at a hanging mercury drop electrode at pH 4.2 allows the determination of this compound in the 1 × 10^?6 M ^? 1 × 10^?9 M concentration range. Applying a square-wave potential scan provides a 200-fold increase of the peak current compared to differential pulse stripping voltammetry. The influence of several operational parameters such as the nature and the pH of the supporting electrolyte, the deposition time and the potential are discussed. Interactions between the adsorbed molecules occur during the deposition step.     

Simultaneous Determination of Cadmium,Lead, Copper,and Thallium in Highly Saline Samples by Anodic Stripping Voltammetry (ASV) Using Mercury‐Film and Bismuth‐Film Electrodes

This paper describes a comparative study of the simultaneous determination of Cd(II), Pb(II), Tl(I), and Cu(II) in highly saline samples (seawater, hydrothermal fluids, and dialysis concentrates) by ASV using the mercury‐film electrode (MFE) and the bismuth‐film electrode (BiFE) as working electrodes. The features of MFE and BiFE as working electrodes for the single‐run ASV determinations are shown and their performances are compared with that of HMDE under similar conditions. It was observed that the stripping peak of Tl(I) was well separated from Cd(II) and Pb(II) peaks in all the studied saline samples when MFE was used. Because of the severe overlapping of Bi(III) and Cu(II) stripping peaks in the ASV using BiFE, as well as the overlapping of Pb(II) and Tl(I) stripping peaks in the ASV using HMDE, the simultaneous determination of these metals was not possible in highly saline medium using these both working electrodes. The detection limits calculated for the metals using MFE and BiFE (deposition time of 60 s) were between 0.043 and 0.070 μg L^?1 for Cd(II), between 0.060 and 0.10 μg L^?1 for Pb(II) and between 0.70 and 8.12 μg L^?1 for Tl(I) in the saline samples studied. The detection limits calculated for Cu(II) using the MFE were 0.15 and 0.50 μg L^?1 in seawater/hydrothermal fluid and dialysis concentrate samples, respectively. The methods were applied to the simultaneous determination of Cd(II), Pb(II), Tl(I), and Cu(II) in samples of seawater, hydrothermal fluids and dialysis concentrates.     

New Protocol for Determination of Rifampicine by Adsorptive Stripping Voltammetry

For determinations of organic compounds by adsorptive stripping voltammetry till now the same material of the electrode has been used for the accumulation and stripping steps. This paper describes a new protocol for extending the range of organic compounds, which can be determined by adsorptive stripping voltammetry. In the proposed procedure the accumulation step was performed on the electrode modified by a lead film, which assures adsorption of the studied species on the modified electrode and then the stripping step of the accumulated substance was performed on the support of the lead film electrode. As an example rifampicine was accumulated by adsorption at the lead film electrode while in the stripping step lead film and then the accumulated rifampicine were oxidized at a glassy carbon electrode. Using an acetate buffer as a supporting electrolyte a calibration graph for rifampicine in the range from 2.5×10^?10 to 1×10^?8 mol L^?1 was obtained. The detection limit for rifampicine following 60 s accumulation time was equal to 9×10^?11 mol L^?1. The obtained detection limit was comparable or lower than reported previously for other stripping voltammetric procedures. The proposed procedure was applied to rifampicine determination in pharmaceutical preparation.     

Pt‐Nanoparticle Incorporated Carbon Paste Electrode for the Determination of Cu(II) Ion by Anodic Stripping Voltammetry

Pt‐nanoparticles were synthesized and introduced into a carbon paste electrode (CPE), and the resulting modified electrode was applied to the anodic stripping voltammetry of copper(II) ions. The synthesized Pt‐nanoparticles were characterized by cyclic voltammetry, scanning electron microscopy and X‐ray photoelectron spectroscopy techniques to confirm the purity and the size of the prepared Pt‐nanoparticles (ca. 20 nm). This incorporated material seems to act as catalysts with preconcentration sites for copper(II) species that enhances the sensitivity of Cu(II) ions to Cu(I) species at a deposition potential of ?0.6 V in an aqueous solution. The experimental conditions, such as, the electrode composition, pH of the solution, pre‐concentration time, were optimized for the determination of Cu(II) ion using as‐prepared electrode. The sensitivity changes on the different binder materials and the presence of surfactants in the test solution. The interference effect of the coexisted metals were also investigated. In the presence of surfactants, especially TritonX‐100, the Cu(II) detection limit was lowered to 3.9×10^?9 M. However, the Pt‐nanoparticle modified CPE begins to degrade when the period of deposition exceeds to 10 min. Linear response for copper(II) was found in the concentration range between 3.9×10^?8 M and 1.6×10^?6 M, with an estimated detection limit of 1.6×10^?8 M (1.0 ppb) and relative standard deviation was 4.2% (n=5).     

Adsorptive Stripping Analysis of Riboflavin at Electrically Heated Graphite Cylindrical Electrodes

Electrically heated graphite cylindrical electrodes (HGCEs) made from ground pencil leads have been used to perform adsorptive stripping square wave voltammetry (SWV) measurements of trace riboflavin (RF). The SWV stripping peak current was significantly enhanced with increasing the electrode temperature only during preconcentration step. This enhancement was due to the forced thermal convection induced by heating the electrode rather than the bulk solution. It is the thermal convection that has the ability to improve mass transfer and facilitate adsorption thus enhance stripping responses. It was found that the detection limit of 5×10^?9 M (S/N=3) could be obtained at an electrode temperature of 72 °C during 5 min accumulation, more than one magnitude lower than that at 22 °C (room temperature), the sensitivity could be enhanced ca. eight or four folds for two different RF concentration ranges. So it is possible to develop a new highly sensitive method to determine riboflavin at HGCEs. Such HGCEs were also successfully used to determine RF in multivitamin tablets.     

Catalytic Adsorptive Stripping Voltammetry at a Carbon Paste Electrode for the Determination of Amiodarone

Voltammetry using solid electrodes usually suffers from the contamination due to the deposition of the redox products of analytes on the electrode surface. The contamination has resulted in poor reproducibility and overelaborate operation procedures. The use of the chemical catalysis of oxidant on the reduction product of analyte not only can eliminate the contamination of analyte to solid electrodes but also can improve the faradaic response of analyte. This work introduced both the catalysis of oxidant K2S2O8 and the enhancement of surfactant Triton X-100 on the faraday response of amiodarone into an adsorptive stripping voltammetry at a carbon paste electrode for the determination of amiodarone. The method exhibits high sensitivity, good reproducibility and simple operation procedure. In 0.2 mol·L^-1 HOAc-NaOAc buffer （pH=5.3） containing 2.2×10^-2 mol·L^-1 K2S2O8 and 0.002% Triton X-100, the 2.5th-order derivative stripping peak current of the catalytic wave at 0.3 V （vs. Ag/AgCl） is rectilinear to amiodarone concentration in the range of 2.0×10^-10-2.3×10^-8 mol·L^-1 with a detection limit of 1.5×10^-10 mol·L^-1 after accumulation at 0 V for 30 s.     

Electrochemical Behavior of Carvedilol and Its Adsorptive Stripping Determination in Dosage Forms and Biological Fluids

Carvedilol is used in the management of hypertension and angina pectoris and as an adjunct to standard therapy in symptomatic heart failure. The electrochemical oxidation of carvedilol was investigated using cyclic, linear sweep voltammetry at a glassy carbon electrode. In cyclic voltammetry, in all values of pH, the compound shows two irreversible oxidation peaks. These two peaks are related to the different electroactive part of the molecule. First and second peak currents were found as diffusion and adsorption controlled, respectively. Using second oxidation step, two voltammetric methods were described for the determination of carvedilol by differential pulse adsorptive stripping voltammetry (AdSDPV) and square‐wave adsorptive stripping voltammetry (AdSSWV) at a glassy carbon electrode. Accumulation of carvedilol was found to be optimized in 0.2 M H₂SO₄ solution following 275 second accumulation time at open circuit condition. Under optimized conditions, the current showed a linear dependence with concentration in the range between 2×10^?7 M and 2×10^?5 M in supporting electrolyte and in the range between 2×10^?7 M and 1×10^?5 M in spiked human serum samples for both methods. These methods were successfully applied for the analysis of carvedilol pharmaceutical dosage forms and spiked human serum samples. The repeatability and reproducibility of the methods for all media were determined. Precision and accuracy were also found. No electroactive interferences from the tablet excipients and endogenous substances from biological material were found.     

Anodic Stripping Voltammetry Using a Vibrating Electrode

This work proposes a vibrating microwire electrode as working electrode in stripping voltammetry. The vibration was found to maintain a constant and thin (1–2 μm) diffusion layer during the deposition step. The electrode vibration eliminated the need for external stirring of the solution, thus facilitating in situ detection in the environment. The vibration was effected by fixing a low‐voltage (3 V), asymmetric, electrical rotor to the working electrode (a gold microwire of either 5 or 25 μm). The sensitivity of the vibrated electrode was ca. 22×greater than stationary. Measurements of copper (4 nM) by anodic stripping voltammetry using the vibrating electrode had a low standard deviation (1% for n=6) indicating that the diffusion layer had only minor variability. The agitation mechanism was unaffected by water moving at >2 m s^?1 and by water pressure equivalent to a depth of >40 m, indicating its suitability for in situ measurements. The vibrating probe was used for in situ detection of copper by anodic stripping voltammetry to a depth of 6 m. Using a 5 min deposition time, the limit of detection for labile copper was 38 pM.     

Ex Situ Prepared Antimony Film Electrode for Electrochemical Stripping Measurement of Heavy Metal Ions

The antimony film electrode (SbFE) was prepared ex situ for anodic and adsorptive stripping voltammetric measurement of selected heavy metal ions. The electrode revealed good linearity for Cd(II) and Pb(II) in a nondeaerated solution of 0.01 M HCl in the examined concentration range from 25 to 80 μg L^?1 with limits of detection of 1.1 μg L^?1 for Cd(II) and 0.3 μg L^?1 for Pb(II) and an excellent reproducibility. The preplated SbFE was also preliminary tested for measuring low levels of Ni(II) using adsorptive stripping voltammetry exhibiting good linearity and sensitivity in combination with only a 30 s deposition step.     

Anodic stripping voltammetry with mercury electrodes in extracts of cadmium,lead, thallium and indium diethyldithiocarbamate complexes and analysis of mixtures

The selectivity of the determination of traces of cadmium, lead, thallium and indium is improved by direct coupling of liquid/liquid extraction and anodic stripping voltammetry. Metals are extracted from aqueous solution to benzene or chloroform after the addition of sodium or zinc diethyldithiocarbamate. Stripping voltammetry of Cd, Tl and Pb at a hanging mercury drop electrode or mercury film electrode is done in benzene/methanol medium (1:1) with 0.1 M NaClO₄ as supporting electrolyte. For indium, the medium is chloroform/ethanol/water (1:4:1) with 0.005 M sodium acetate/0.06 M KBr/0.06 M HCl as supporting electrolyte. The complexes in acidic solution can be decomposed by mercury (II) ions, which provides useful shifts of deposition potentials. Calibration graphs are linear at concentrations of about 10^?7 M with a detection limit of 1×10^?8 M. The method is applied to determine a single metal in the presence of a large amount (1000-fold) of interfering metal.     

Catalytic Adsorptive Stripping Voltammetry of Cobalt in the Presence of Dimethylglyoxime and Nitrite at In Situ Plated Lead–Copper Film Electrode

A lead‐copper film electrode was proposed for Co(II) determination by catalytic adsorptive stripping voltammetry. The electrode was plated in situ and hence the exchange of a solution after plating step was not required. At optimized conditions the calibration graph for Co(II) was linear from 5×10^?10 to 2×10^?8 mol L^?1 for accumulation time of 15 s. The relative standard deviation for Co(II) determination at concentration 5×10^?9 mol L^?1 was 4.1%. The detection limits for Co(II) were 1.2×10^?10 and 1.0×10^?11 mol L^?1 for an accumulation time of 15 and 180 s, respectively. The method was applied to Co(II) determination in certified reference material and other water samples.     

Determination of Trace Tl(I) by Anodic Stripping Voltammetry on Novel Disposable Microfabricated Bismuth‐Film Sensors

This work reports the trace determination of Tl(I) by square‐wave anodic stripping voltammetry (SWASV) on novel microsensors equipped with a bismuth‐film electrode (BiFE). The sensors were fabricated by a multistep microfabrication approach combining sputtering (to deposit the electrode materialm, bismuth‐ and the insulator SiO₂, on the surface of a silicon wafer) and photolithography (to define the geometry of the sensor). The effect of the preconcentration time, the preconcentration potential and the SW stripping parameters were investigated. Using the selected conditions, the 3σ limit of detection was 0.6 µg L^?1 of Tl(I) at a preconcentration time of 240 s and the percent relative standard deviation was 4.3 % at the 10 µg L^?1 level (n=8). In order to eliminate the interference caused by Pb(II) and Cd(II), EDTA was added in the sample solution The method was successfully applied to the determination of Tl(I) in a certified lake water sample. These new sensors exhibit excellent mechanical stability and offer wide scope as mercury‐free disposable sensors for trace metal analysis.     

Experimental design as an optimization approach for fabrication a new selective sensor for thallium(I) based on calix[6]arene

The performance of a new membrane sensor based on polyvinyl chloride (PVC) for Tl(I) assay was investigated using the statistical design as an optimization strategy. The Plackett-Burman and Box-Behnken designs, respectively, were utilized to find out the influencing variables and optimization of conditions. In order to evaluate the relationship between the responses of electrode (slope) and significant variables along with their interactions, a mathematical model was presented. The interactions between significant variables were intuitively illustrated according to the response surface plots. Apart from that, the optimum conditions as a result of response surface methodology for both membrane ingredients and measuring conditions such as pH, PVC, internal solution concentration, calix[6]arene, 2-nitrophenyloctylether, potassium tetrakis-(p-chlorophenyl)borate and time conditioning, respectively, were found to be: 6, 0.028 g, 0.001 M, 0.0035 g, 0.065 g, 0.0015 g and 20 h. The optimized sensor exhibits a Nernstian response for thallium(I) over a wide linear range from 2.0 × 10^?6 to 2.0 × 10^?2 M and the slope of 57.9 ± 0.1 mV/decade of the activity and limit of detection (LOD) 1.9 × 10^?5 M. The relative standard deviations (RSD) for six replicates of the measurement at 1 × 10^?5 and 1 × 10^?5 M of Tl(I) were 2.7 and 3.0%, respectively. The favorable results were given through the direct determination of Tl(I) in spiked wastewater and artificial spiked urine sample with Tl(I). The electrode was also successfully applied to the titration of a Tl(I) solution with KI.     

Stripping voltammetric determination of azide ions

A procedure is proposed for the stripping voltammetric determination of N ₃ ^? ions at a mercury film electrode. It is based on the reduction of the mercury azide formed upon the oxidation of mercury in the presence of N ₃ ^? at ?0.02 to ?0.04V (in reference to an Ag/AgCl electrode) in a 0.1 M Na₂SO₄ supporting electrolyte solution. A linear dependence of the cathodic current peak on the N ₃ ^? concentration is observed in the concentration range from 4 × 10^?9 to 1 × 10^?3 M.