A simple spectrophotometric procedure for the determination of antimony (III) and (V) in antileishmanial drugs

A spectrophotometric method for the selective determination of antimony (III) and (V) in antileishmanial drugs is described. The procedure is based on the reaction of Sb(III) with bromopyrogallol red (BPR) in neutral solution. As a consequence of the Sb-BPR complex formed, the absorbance of BPR, at 560 nm, decreases proportionally to the amount of Sb(III) in the analyte solution. The calculated apparent molar absorptivity and determination limits are 3.67 × 10⁴ L · cm^–1 · mol^–1 and 1.65 × 10^–6 mol/L, respectively. Sb(V) is determined after reduction to Sb(III) by iodide. The Sb(V) content determined in ten samples of Glucantime varied from 75.40 ± 0.97 to 94.47 ± 1.0 mg/mL. Sb(III) was detected in all samples analyzed, and mean values ranged from 5.19 ± 0.16 to 10.52 ± 0.15 mg/mL. The method is suitable for the routine quality control of pharmaceutical formulations. Received: 26 July 1996 / Revised: 17 October 1996 / Accepted: 11 December 1996     

Differential determination of arsenic(III) and arsenic(V), and antimony(III) and antimony(V) by hydride generation-atomic absorption spectrophotometry,and its application to the determination of these species in sea water

A method is described for the differential determination of As(III) and As(V). and Sb(III) and Sb(V) by hydride generation-atomic absorption spectrophotometry with hydrogen-nitrogen flame using sodium borohydride solution as a reductant. For the determination of As(III) and Sb(III), most of the elements, other than Ag⁺, Cu²⁺, Sn²⁺, Se⁴⁺ and Te⁴⁺, do not interfere in an at least 30,000 fold excess with respect to As(III) or Sb(III). This method was applied to the determination of these species in sea water and it was found that a sample size of only 100 ml is enough to determine them with a precision of 1.5–2.5%. Analytical results for surface sea water of Hiroshima Bay were 0.72 μgl^?1, 0.27 μgl^?1 and 0.22 μgl^?1 for As(total), As(III) and Sb(total), respectively, but Sb(III) was not detected in the present sample. The effect of acidification on storage was also examined.     

Determination of antimony(III) and (V) in natural water by cathodic stripping voltammetry with in-situ plated bismuth film electrode

A method is described for the sequential determination of Sb(III) and Sb(V) using Osteryoung square wave cathodic stripping voltammetry. It employs an in-situ plated bismuth-film on an edge-plane graphite substrate as the working electrode. Selective electro-deposition of Sb(III)/Sb(V) is accomplished by applying a potential of ?500 mV vs. Ag/AgCl, followed by reduction to stibine at a more negative potential in the stripping step. Stripping was carried out by applying a square wave waveform between ?500 and ?1400 mV to the antimony deposited. The stripping peak current at ?1150 mV is directly proportional to the concentration of Sb( III)/Sb(V). The calibration plots for Sb (III) were linear up to 12.0?µg L^?1 depending on the time of deposition. The calibration plots for Sb (V) were linear up to 7.0?µg L^?1, also depending on the time of deposition. The relative standard deviation in the determination of 0.1?µg L^?1 of Sb(III) is 4.0% (n?=?5), and the limit of detection is as low as 2 ng L^?1. In case of 0.1?µg L^?1 Sb(V), the relative standard deviation is 3.0% (n?=?5) and the detection limit also is 2 ng L^?1. The method was applied to the analysis of river and sea water samples.     

Chromium(III) Ion Selective Electrode Based on Oxalic Acid Bis(Cyclohexylidene Hydrazide)

A poly(vinyl chloride) membrane sensor based on oxalic acid bis (cyclohexylidene hydrazide) as membrane carrier was prepared and investigated as a Cr(III)‐selective electrode. The electrode reveals a Nernstian behavior (slope 19.8±0.4 mV decade^?1) over a wide Cr(III) ion concentration range 1.0×10^?7–1.0×10^?2 mol dm^?3 with a very low limit of detection (i.e., down to 6.3×10^?8 mol dm^?3). The potentiometric response of the sensor is independent of the pH of the test solution in the pH range 1.7–6.5. The electrode possesses advantage of very fast response, relatively long lifetime and especially good selectivity to wide variety of other cations. The sensor was used as an indicator electrode, in the potentiometric titration of chromium ion and in the determination of Cr(III) in waste water and alloy samples.     

Spectrophotometric determination of Chromium(VI) using cyclam as a reagent

A simple, rapid, sensitive, and inexpensive method for spectrophotometric determination of chromium(VI), based on the absorbance of its complex with 1,4,8,11-tetraazacyclotetradecane (cyclam) is presented. The complex showed a molar absorbtivity of 1.5?×?10⁴?L?mol^?1?cm^?1 at 379?nm. Under optimum experimental conditions, a pH of 4.5 and 1.960?×?10³?mg?L^?1 cyclam were selected, and all measurements were performed 10?min after mixing. Major cations and anions did not show any interference; Beer's law was applicable in the concentration range 0.2–20?mg?L^?1 with a detection limit of 0.001?mg?L^?1. The standard deviation in the determination is ±0.5?mg?L^?1 for a 15.0?mg?L^?1 solution (n?=?7). The described method provides a simple and reliable means for determination of Cr(VI) in real samples.     

Spectrophotometric determination of chloride in non-polar media by the mercury(II) thiocyanate reaction

A simple, rapid and accurate method for the spectrophotometric determination of chloride in non-polar media is described. The method is based on the well-known reaction of mercury(II) thiocyanate with chloride to release thiocyanate, which then reacts with iron(III). The optimum concentrations of reagents for the determination of chloride in 2,2,4-trimethylpentane (iso-octane) and cyclohexane are reported. The molar absorptivity of the complex at 505 nm is 5120 ± 200 dm³ mol^?1 cm^?1 for iso-octane and 5340 ± 340 dm³ mol^?1 cm^?1 for cyclohexane. Beer's Law is obeyed in the range 2 × 10^?7–2 × 10^?5 mol dm^?3 (0.01–1 mg l^?1) chloride.     

Spectrophotometric Determination of Antimony (III) By Solvent Extraction with Mandelic Acid and Malachite Green

Abstract

A sensitive and selective method has been developed for the spectrophotometric determination of antimony in the tervalent oxidation state. It was found that antimony (III) reacts with mandelic acid to form a complex anion extractable into chlorobenzene with malachite green in weak acidic media (pH 2.2 to 3.5) at room temperature and is determined indirectly by measuring the absorbance of malachite green in the extract at 628 nm. The calibration graph is linear for antimony (III) over the range 0.088–1.8 mg 1^?1 (7.2 × 10^?7–1.5 × 10^?5 mol 1^?1) with the apparent molar absorptivity ε × 6.9 × 10⁴ 1 mol^?1 cm^?1. Antimony (V) was slightly extracted in the presence of phosphate buffer with ε × 2.7 × 10³ 1 mol^?1 cm^?1.     

Chemical Speciation of Antimony(III and V) in Water by Adsorptive Cathodic Stripping Voltammetry Using the 4‐(2‐Thiazolylazo) – Resorcinol

A simple adsorptive cathodic stripping voltammetry method has been developed for antimony (III and V) speciation using 4‐(2‐thiazolylazo) – resorcinol (TAR). The methodology involves controlled preconcentration at pH 5, during which antimony(III) – TAR complex is adsorbed onto a hanging mercury drop electrode followed by measuring the cathodic peak current (I_p,c) at ?0.39 V versus Ag/AgCl electrode. The plot of I_p,c versus antimony(III) concentration was linear in the range 1.35×10^?9–9.53×10^?8 mol L^?1.The LOD and LOQ for Sb(III) were found 4.06×10^?10 and 1.35×10^?9 mol L^?1, respectively. Antimony(V) species after reduction to antimony(III) with Na₂SO₃ were also determined. Analysis of antimony in environment water samples was applied satisfactorily.     

Modified Screen-Printed Electrode for Potentiometric Determination of Copper(II) in Water Samples

Modified screen printed (SPE) and carbon paste electrodes (CPE) with phenanthroline–tetraphenyl borate ionophore [Phen:TPB] were fabricated for the determination of copper(II). The modified electrodes have linear responses over a wide concentration range (1 × 10^?6–1 × 10^?2 mol·L^?1) of copper(II) ion at 25 °C with divalent cationic slopes of 29.85 ± 0.58 and 29.45 ± 0.81 mV·decade^?1 and exhibit a detection limit of 1 × 10^?6 mol·L^?1 for SPE and CPE. The selectivity coefficient was measured using the match potential method in acetate buffer of pH = 4.2. The modified SPE and CPE sensors show high selectivity and sensitivity for determination of copper(II) and also show stable and reproducible response over a period of five and three months for SPE and CPE sensors, respectively. This method can be used for determination of copper(II) in water, soil, plant and fish tissue samples and the results obtained agreed with those obtained with atomic absorption spectrometer (AAS).     

Removal of Zn(II) Ions from Aqueous Solution Using BPHA‐Impregnated Polyurethane Foam

Zn(II) ions sorption onto N‐Benzoyl‐N‐Phenylhydroxylamine (BPHA) impregnated polyurethane foam (PUF) has been studied extensively using radiotracer and batch techniques. Maximum sorption (～98%) of Zn(II) ions (8.9 × 10^?6 M) onto sorbent surface is achieved from a buffer of pH 8 solution in 30 minutes using 7.5 mg/mL of BPHA‐impregnated polyurethane foam at 283 K. The sorption data follow Langmuir, Freundlich and Dubinin‐Radushkevich (D‐R) isotherms. The Langmuir constants Q = 18.01 ± 0.38 μ mole g^?1 and b = (5.39 ± 0.98) × 10³ L mole^?1 have been computed. Freundlich constants 1/n = 0.29 ± 0.01 and C_m = 111.22 ± 12.3 μ mole g^?1 have been estimated. Sorption capacity 31.42 ± 1.62 μ mole g^?1, β = ?0.00269 ± 0.00012 kJ² mole^?2 and energy 13.34 ± 0.03 kJ mole^?1 have been evaluated using D‐R isotherm. The variation of sorption with temperature yields ΔH = ?77.7 ± 2.8 k J mole^?1, ΔS = ?237.7 ± 9.3 J mole^?1 K^?1 and ΔG = ?661.8 ± 117.5 k J mol^?1 at 298 K reflecting the exothermic and spontaneous nature of sorption. Cations like Fe(III), Ce(III), Al(III), Pb(II) and Hg(II) and anions, i.e., oxalate, EDTA and tartrate, reduce the sorption significantly, while iodide and thiocyanate enhanced the sorption of Zn(II) ions onto BPHA‐impregnated polyurethane foam.     

Direct determination of bismuth(III) in sea water by square-wave anodic stripping voltammetry at a glassy-carbon rotating-disk electrode

A method for the determination of bismuth(III) in untreated sea water at its natural pH of 8.1 is described. A bare glassy-carbon rotating-disk electrode is preconditioned by placing in the sample at an applied potential of ?0.8 V vs. Ag/AgCl for 20 min; after stripping to ?0.4 V, bismuth is accumulated for 5 min at ?0.8 V and finally stripped in the square-wave mode. The bismuth peak appears at ca. + 0.10 V vs. Ag/AgCl; peak height is linearly related to concentration up to 2×10^?10 mol dm^?3. The method is highly selective for bismuth. The concentration of Bi(III) in the investigated sample was (6±1)×10^?11 mol dm^?3, or 12±2 ng dm^?3. The different types of response obtained are discussed.     

Contribution to the adsorption voltammetric determination of manganese

The adsorption voltammetric determination of Mn(II) with Bromopyrogallol Red (BPR) and Mordant Red 19 (MDR) has been investigated using a hanging drop mercury electrode. In NH₃/NH₄Cl solution, ligands and Mn(II) complexes give well separated voltammetric peaks after enrichment onto the electrode. The conditions for determining manganese by adsorption voltammetry with these reagents have been investigated in detail, as has the influence of foreign ions on the determination. The detection limits are 4·10^?10 mol/L Mn for BPR and 8·10^?10 mol/L Mn for MDR, respectively.     

Selective substoichiometry for inorganic arsenic(V) by ion-pair extraction with pyrogallol/tetraphenyl-arsnium chloride and its application in the analysis of seaweed

Arsenic(V) is substioichiometrically extracted from 0.4–3 M sulfuric acid solutions into 1,2-dichloroethane with 1.0 × 10^?5 M teraphenylarsnium chloride in the presence of 2.0 × 10^?1 M pyrogallol. Reproducibility of the substoichiometric extractions with a constant amount of tetraphenylarsonium chloride is high (0.5% RSD). This substiochiometric extraction is very selective for arsenic(V) from arsenic(III), monomethylarsonic acid, and dimethylarsinic acid. The extraction combined with the isotope dilution principle was applied to the determination of arsenic(V) in an acid-digestd solution of a seaweed sample (Laminaria religiosa Miyabe) and to the determination of total arsenic in this sample.     

银（III）配合物-鲁米诺流动注射化学发光新体系测定肾上腺素

儿茶酚胺是一类非常重要的神经递质,在人体的心血管系统、神经系统、内分泌腺、肾脏、平滑肌等组织系统的生理活动中起着广泛的调节作用。肾上腺素为儿茶酚胺的一种,建立灵敏、高效的肾上腺素检测技术具有重要的临床意义。本文将银（Ⅲ）配合物与鲁米诺组成新的流动注射化学发光体系,利用碱性介质中肾上腺素对三价银配合物－鲁米诺化学发光体系有明显的增强效应来测定肾上腺素的含量,并据此建立了高效测定肾上腺素的流动注射化学发光新方法。在优化的条件下,该方法测定肾上腺素的线型范围为1.0×10－9～1.0×10－7 mol L-1,检出限为8.0×10－10 mol L-1,对1.5×10－8 mol L-1肾上腺素11次平行测定,其相对标偏差为2.9％。利用建立的分析方法测定了药物肾上腺素,并对三价银－鲁米诺化学发光新体系测定肾上腺素的反应机理进行了讨论。     

Ruthenium(III) Schiff's Base Complex as Novel Chloride Selective Membrane Sensor

A novel chloride PVC‐based membrane sensor based on a ruthenium(III) Schiff's base complex, as an excellent neutral carrier, has been developed. The ruthenium complex, in combination with a ketonic plasticizer and a cationic additive led to ISEs with fundamental characteristics, such as slope sensitivity, short response times and selectivity coefficients, which were sufficient for practical applications. The sensor with composition of 30% PVC, 62% benzyl acetate, 5% ruthenium(III) Schiff's base complex and 3% hexadecyltrimethyl ammonium bromide displays near‐Nernstian behavior in a wide concentration range (1.0×10^?1–3.0×10^?6 M with slope of ?54.5±0.5) with a detection limit of 2.0×10^?6 M (71.0 ng per mL). The response of the electrode is independent on pH in the range of 4.0–10.0 and can it be used for at least ten weeks. The proposed electrode shows a very short response time (<20 s) in whole concentration range. The sensor displays high selectivity toward chloride ions over several organic and inorganic anions. It was successfully applied for the determination of chloride in serum samples. It was also used as an indicator electrode in the potentiometric titration of chloride ions with silver nitrate solution.     

Application of ultrasonic-assisted cloud point extraction/flame atomic absorption spectrometry (UA-CPE/FAAS) for preconcentration and determination of low levels of antimony in some beverage samples

Due to be able to migrate or leach from food packaging materials into the foods and/or beverages, development of a new, sensitive and selective analytical methods for low levels of antimony as a food contaminant is of great importance in terms of food safety. In this context, an ultrasonic-assisted cloud point extraction method was developed for the preconcentration and determination of antimony as Sb(III) using 4-(2-thiazolylazo)resorcinol (TAR) and 2-(2-thiazolylazo)-p-cresol (TAC) as chelating agents and sodium dodecyl sulfate as signal enhancing agent at pH 6.0 and mediated by nonionic surfactant, t-octylphenoxypolyethoxyethanol by flame atomic absorption spectrometry. Using the optimized conditions, the calibration curves obtained from Sb(III) with TAR and TAC were linear in the concentration ranges of 0.5–180 and 1–180 μg L^?1 with detection limits of 0.13 and 0.28 μg L^?1, respectively. The precision (as relative standard deviations, RSDs) was lower than 3.9 % (25 and 100 μg L^?1, n: 6). The method accuracy was validated by the analysis of two standard reference materials. The results obtained were statistically in a good agreement with the certified values at 95 % confidence limit. The method has successfully been applied to the determination of Sb(III) and total Sb in selected beverages, milk and fruit-flavored milk products before and after pre-reduction of Sb(V) to Sb(III) with a mixture of KI/ascorbic acid in acidic media. The Sb(V) contents of samples were quantitatively calculated from analytical difference between total Sb and Sb(III) levels.     

Electrochemical Determination of Dopamine with Ruthenium(III)-Modified Glassy Carbon and Screen-Printed Electrodes

Here is reported for the first time the application of sodium bis[N-2-oxyphenyl-5-bromosalicylideneiminato-ONO]ruthenate(III) as a mediator with multiwalled carbon nanotubes and Nafion at glassy carbon and screen-printed electrodes for the determination of dopamine in the presence of ascorbic acid. Electrochemical studies were performed using cyclic voltammetry, differential pulse voltammetry, and flow injection amperometry. In flow injection mode, the flow rate was 0.4?mL?min^?1, the injection volume 250?µL, and the operation potential 0.05?V vs. Ag/AgCl. In 0.1M pH 7.5 phosphate buffer, the sensor provided a linear dynamic range up to 50?mg?L^?1 dopamine with a detection limit of 0.11?±?0.04?mg?L^?1. The sensor was used for the determination of dopamine in ampoules of dopamine hydrochloride by cyclic voltammetry, differential pulse voltammetry, and flow injection amperometry.     

Modification of Glassy Carbon Electrode With Single‐Walled Carbon Nanotubes and α‐Silicomolybdate: Application to Sb(III) Detection

A simple procedure was developed to prepare a glassy carbon (GC) electrode modified with single‐walled carbon nanotubes (SWCNTs) and polyoxometalate. With immersing SWCNTs modified GC electrode in silicon polyoxomolybdate (α‐SiMo₁₂O₄₀^4?) solution (direct deposition) for a short period of time (2–10 s) oxoanion adsorbed strongly and irreversibly on SWCNTs. Cyclic voltammograms of the α‐SiMo₁₂O₄₀^4? incorporated‐SWCNTs indicates three well‐defined and reversible redox couples with surface confined characteristic at wide pH range (1–7). The surface coverage (Γ) of α‐SiMo₁₂O₄₀^4? immobilized on SWCNTs was 2.14 (±0.11)×10^?9 mol cm^?2 indicating high loading ability of SWCNTs for polyoxometalate. The charge transfer rate constant (k_s) of three redox couples of adsorbed α‐SiMo₁₂O₄₀^4? were 9.20 (±0.20), 8.02 (±0.20), and 3.70 (±0.10) s^?1, respectively, indicate great facilitation of the electron transfer between α‐SiMo₁₂O₄₀^4? and CNTs. In this research the attractive mechanical and electrical characteristics of CNTs and unique properties and reactivity of polyoxometalates were combined. The modified electrode in buffer solution containing Sb(III) shows a new redox system at 0.38 V in pH 1. The voltammetric peak current increased with increasing Sb(III) concentration. The differential pulse voltammetry (DPV) technique was used for detection micromolar concentration of antimony. Furthermore, the interference effects various electroactive compounds on voltammetric response of Sb(III) were negligible. Finally the ability of the modified electrode for antimony detection in real samples was evaluated.     

Speciation of Antimony by Adsorptive Stripping Voltammetry Using Pyrogallol Red

This paper proposes a procedure for the speciation of antimony by Differential Pulse Adsorptive Stripping Voltammetry (DPAdSV) using pyrogallol red (PGR) as a complexing agent. It employs a Partial Least Squares regression (PLS) in the resolution of strongly overlapping voltammetric signals obtained from mixtures of Sb(III) and Sb(V) in the presence of pyrogallol red. The absolute value of the relative error was less than 3.5% when concentrations of several mixtures were calculated, the minimum concentrations being 9.98×10^?9 mol dm^?3 and 4.87×10^?8 mol dm^?3 for Sb(III) and Sb(V), respectively. Any undue effects caused by the presence of foreign ions in the solution were also analyzed. The procedure was successfully applied to the speciation of antimony in pharmaceutical preparations.     

Speciation of Antimony(III) and Antimony(V) in Bottled Water by Hydride Generation-Inductively Coupled Plasma Optical Emission Spectrometry

Speciation of Sb(III) and Sb(V) was investigated using hydride generation with the selective formation of stibine from Sb(III). A continuous flow system using a homemade gas-liquid separator with inductively coupled plasma optical emission spectrometry was employed. The conditions and concentrations of NaBH₄, HCl, citric acid, and KI were optimized to obtain limits of detection of 0.05 for Sb(III) and 0.11 µg L^?1 for total Sb without preconcentration. An attractive sampling rate of 26 analyses h^?1 was obtained, suggesting application for routine analysis. The method was employed for the determination of Sb(III) and total Sb in bottled drinking water, and recovery values between 82.0 and 98.8% with relative standard deviation lower than 6.2% were observed, demonstrating appropriate accuracy and precision.