Bi2WO6量子点(QDs)修饰Bi2MoO6-xF2x异质结的构筑及其催化活性增强机理

采用简单沉积-沉淀法合成了Bi₂WO₆@Bi₂MoO_6-xF_2x（BWO/BMO6-xF2x）异质结,借助XRD、XPS、TEM、SEM、EDS、UV-Vis-DRS、PC和EIS等测试技术对其组成、形貌、光吸收特性和光电化学性能等进行系统表征,并以模型污染物罗丹明B（RhB）的光催化降解作为探针反应来评价Bi₂WO₆@Bi₂MoO_6-xF_2x异质结的光催化活性增强机制。形貌分析表明,所得Bi₂MoO₆微球由大量厚度为20~50 nm的纳米片组成;FE-SEM和HR-TEM分析表明,尺寸约为10 nm的Bi₂WO₆量子点均匀沉积在Bi₂MoO_6-xF_2x微球表面,形成新颖的Bi₂WO₆@Bi₂MoO_6-xF_2x异质结;与纯Bi₂MoO₆或者Bi₂WO₆相比,1∶1Bi₂WO₆@Bi₂MoO_6-xF_2x异质结表现出更好的光催化活性和光电流性质,其对RhB光催化降解的表观速率常数分别为纯BMO和BWO的6.4和11.6倍。PC和EIS图谱分析表明,Bi₂WO₆量子点表面沉积显著提高Bi₂MoO_6-xF_2x光生电子/空穴的分离效率和迁移速率;活性物种捕获实验证明了·O₂^-和h⁺是主要的活性物种。根据实验结果,探讨了F^-掺杂和Bi₂WO₆量子点之间的协同效应对Bi₂MoO₆的光催化活性的影响机制。     

三元体系YCl3-CdCl2-H2O和四元体系YCl3-CdCl2-HCl(～8.8%)-H2O (25 ℃)的相平衡及其固相新化合物的研究

The equilibrium solubilities of the ternary system YCl₃-CdCl₂-H₂O, the quaternary system YCl₃-CdCl₂-HCl(～8.8%)-H₂O were determined at 25 ℃ and the phase diagrams were constructed. The results show that the ternary system was complicated with six equilibrim solid phases CdCl₂·2.5H₂O, CdCl₂·H₂O, 8CdCl₂·YCl₃·15H₂O (8∶1 type), 4CdCl₂·YCl₃·13H₂O(4∶1 type), 5CdCl₂·2YCl₃·26H₂O (5∶2 type) and YCl₃·6H₂O. The quaternary system was also complicated with four equilibrim solid phase CdCl₂·H₂O, 4CdCl₂·YCl₃·13H₂O (4∶1 type), 5CdCl₂·2YCl₃·26H₂O(5∶2 type) and YCl₃·6H₂O. Among the three new compounds 8CdCl₂·YCl₃·15H₂O, 4CdCl₂·YCl₃·13H₂O and 5CdCl₂·2YCl₃·26H₂O, 8CdCl₂·YCl₃·15H₂O was a kind of metastable compound only in ternary system, and it was changed into 4CdCl₂·YCl₃·13H₂O with time. Both 4∶1 type and 5∶2 type existed in ternary and quaternary system, but they were also congruently soluble compounds in quaternary system. They have been prepared from the system and have been characterized by XRD, TC-DTG and DSC.     

纳米Mn-Zn铁氧体的制备和研究

Nanosize manganese zinc ferrites were fabricated by hydrothermal precipitation route using Fe₂(SO₄)₃, ZnSO₄·7H₂O, MnSO₄·H₂O as material, then some calcinated at 500 ℃ and studied by XRD, TEM, IR and VSM. The results showed that the products were spinel crystal structure and uniformly sized nanoparticles (15～25 nm) with little aggregation. The analysis of IR showed that the superficial water can be eliminated, but that was embedded in crystal lattice can not be removed by calcinating. The effect Zn content x on the lattice (a) of nanosize Mn_1-xZn_xFe₂O₄ was also discussed. The lattice of nanosize Mn_1-xZn_xFe₂O₄ decreases with x increasing; and its value deviated the standard lattice (a₀) of normal size manganese zinc ferrites. A lot of water was absorbed during the hydrothermal process owing to the large surface of nanosize particles. The change of magnetic properties of Mn_xZn_1-xFe₂O₄ with x increasing was studied: nanosize Mn_xZn_1-xFe₂O₄ particles synthesized by us exhibited peculiar magnetic properties curve with Zn content (x) increasing, Superparamagnetic behaviors of the synthesized ZnFe₂O₄ samples were confirmed by magnetic characterization, which can be explained by the difference between the distribution of the metal ions (Mn²⁺, Zn²⁺ and Fe³⁺) among the tetrahedral (A) and the octahedral (B) sites of nanosize ferrite and that of bulk ferrite.     

掺杂和取代对红色荧光材料SrAl12O19:Mn4+发光性能的影响

SrAl₁₂O₁₉：Mn⁴⁺是一种用于高显色性白光发光二极管的候选红色荧光材料。本论文研究了Mg²⁺、Zn²⁺和Ge⁴⁺离子的掺杂效应以及Ga³⁺、Ca²⁺和Ba²⁺离子的取代效应对SrAl₁₂O₁₉：Mn⁴⁺荧光材料性能的影响。样品通过高温固相反应制备,焙烧温度在1 250~1 500 ℃之间。利用X射线衍射技术表征了材料的相纯度,用荧光激发光谱和发射光谱表征了材料的荧光性能。研究结果指出,与未进行Mg²⁺或Zn²⁺掺杂的样品相比,Mg²⁺或Zn²⁺离子对Al³⁺格位的掺杂可以使材料的发光强度提高~60%,其原因被认为是掺杂促进了激活剂Mn⁴⁺离子进入晶格,其过程可以表示为：MO+MnO₂⇔M_Al^''+M_Al^·+3O_O^×（M=Mg,Zn）,电子顺磁共振谱支持这一结果。Ge⁴⁺离子的掺杂使材料的发光性能明显下降。Ga³⁺离子可以取代Al³⁺离子形成全范围的固溶体,其中少量Ga³⁺离子的掺杂可以使材料的荧光发射强度提高~13%,而掺杂量进一步提高使材料的荧光性能下降。Ca²⁺和Ba²⁺对Sr²⁺的取代仅形成有限范围的固溶体。Ca²⁺的取代使材料的发光性能提高;而 Ba²⁺的取代使材料的发光强度下降。     

电荷补偿对Ba2ZnGe2O7：Bi3+荧光粉发光性质的影响

采用高温固相法制备了2个系列的荧光粉样品：Ba_2-xZnGe₂O₇：xBi³⁺（系列Ⅰ）和Ba_1.994-yK_yZnGe₂O₇：0.006Bi³⁺（系列Ⅱ）。X射线衍射（XRD）测试结果表明,少量Bi³⁺、K⁺的掺杂不会明显改变材料的物相结构。样品的荧光光谱测试结果表明,虽然2个系列样品的发光光谱都随组成成分变化有少量变化,但发光颜色基本上均为黄绿色。在358 nm的激发下,荧光粉的发射光谱呈现一个峰值在500 nm的宽发射带,归属于³P₁→¹S₀能级跃迁。在500 nm监测下,荧光粉的最强激发峰位于358 nm,归属于¹S₀→³P₁能级跃迁,此外还有一个位于320 nm的肩峰归属于O^2--Bi³⁺电荷转移带。系列Ⅰ样品的光谱数据结果指出,Bi³⁺的最佳掺杂量x为0.006。在该基质中,Bi³⁺掺杂取代Ba²⁺属于不等价取代,会在晶格中产生Ba²⁺空位或间隙O^2-,对材料的发光强度产生负面影响。对此,采用K⁺与Bi³⁺协同掺杂起到电荷补偿的作用,填补Ba²⁺空位或捕获间隙O^2-缺陷。空位被填补或间隙被捕获均减少了晶格畸变,从而使发光强度明显提高。系列Ⅱ样品的光谱数据表明,完全电荷补偿的荧光粉样品相比于没有掺K⁺的样品,其发光强度提高了约2.5倍。     

g-C3N4/CaTi2O5复合材料制备及其光催化性能

利用类石墨氮化碳（g-C₃N₄）和亚稳相钙钛氧化物（CaTi₂O₅）固相法制备C₃N₄/CaTi₂O₅复合材料。利用X射线衍射（XRD）、金相显微镜、扫描电子显微镜（SEM）及附带能谱分析仪（EDS）和N₂吸附-脱附对样品的显微结构和比表面积进行检测分析,并用紫外-可见吸收光度计（UV-Vis）测试了样品的光吸收性能,研究C₃N₄与CaTi₂O₅物质的量之比（n_C3N4/nCaTi₂O₅）对C₃N₄/CaTi₂O₅复合样品的物相结构和微观形貌的影响,同时考察C₃N₄/CaTi₂O₅复合样品在可见光照射下光催化降解罗丹明染料效果。实验结果表明：相比纯C₃N₄和CaTi₂O₅样品,C₃N₄/CaTi₂O₅复合样品在可见光下具有较高的光催化性能,随着n_C3N4/nCaTi₂O₅增加,样品的光催化降解率随之增加而后降低,当n_C3N4/nCaTi₂O₅=1：1时,样品的光催化降解率达到最大值99.5%,并且循环重复利用5次后,样品的光催化剂降解率仍几乎保持不变。复合样品光催化性能提高主要归因于复合能级结构有效地抑制了电子和空穴复合所致。     

CO2在纳米SiO2/TiO2悬浮体系中的光催化还原

用水热法合成了氧化硅改性的具有高比表面积、高催化活性的锐钛型二氧化钛, 并在其悬浮体系中将CO₂光催化还原合成甲醇. 采用XRD, TEM, 物理吸附, UV-Vis吸收光谱和FTIR等表征手段对催化剂结构特征进行了研究. 结果表明: 添加氧化硅后, 氧化硅和二氧化钛之间形成Si—O—Ti键, 抑制了TiO₂晶粒生长, 提高了锐钛型TiO₂的比表面积, 且随着含硅量的增加, SiO₂/TiO₂的UV吸收逐步蓝移, 禁带宽度增加. 还原反应结果表明: SiO₂/TiO₂具有光催化还原活性, 且随着含硅量的增加先增加后减小, 当SiO₂质量分数为3.5%时, SiO₂/TiO₂复合催化剂反应活性最强, 5 h内甲醇产量可达到21.0 mg/L, 并有少量甲醛生成.     

四种Keggin型多酸纳米材料的制备及其吸附有机染料的性能

以4种Keggin型多酸作为原料(分别为H₃PW₁₂O₄₀·36H₂O(简写为PW₁₂^a)、H₃PMo₁₂O₄₀·34H₂O(简写为PMo₁₂^a)、H₄SiW₁₂O₄₀·35H₂O(简写为SiW₁₂^a)和H₄GeW₁₂O₄₀·40H₂O(简写为GeW₁₂^a)),采用表面活性剂智能化控制的软化学法制备了相应的4种Keggin型多酸纳米材料,分别为Ag₃PW₁₂O₄₀·36H₂O(简写为PW₁₂^b)、Ag₃PMo₁₂O₄₀·34H₂O(简写为PMo₁₂^b)、Ag₄SiW₁₂O₄₀·35H₂O(简写为SiW₁₂^b)和Ag₄GeW₁₂O₄₀·40H₂O(简写为GeW₁₂^b)。采用IR、UV-Vis、XRD和SEM表征多酸的结构和纳米粒子的形貌。在室内黑暗条件下,100mg样品可在5min内把20mg·L^-1的100mL亚甲基蓝(MB)染料溶液脱色,使其变为接近无色,吸附效率最高可达96.3%,吸附效率大小为PMo₁₂^b >PW₁₂^b >GeW₁₂^b >SiW₁₂^b。相同条件下,100mg样品使20mg·L^-1的100mL罗丹明B(RhB)染料溶液30min内脱色完全,脱色效率最高可达96.1%,吸附效率大小为PW₁₂^b >PMo₁₂^b >SiW₁₂^b >GeW₁₂^b。说明该4种多酸纳米材料具有较高的吸附有机染料性能。     

ZnAl2O4:Mn材料的制备及发光性能

以共沉淀法与煅烧法联用,成功制备了一系列ZnAl₂O₄:xMn样品。通过扫描电镜和X射线粉末衍射测试研究了样品的形貌和物相特征,结果表明尖晶石结构的ZnAl₂O₄中[AlO₆]的八面体位可以有效被Mn⁴⁺替代。通过荧光激发和发射光谱研究了样品的发光性能,发现Mn⁴⁺在ZnAl₂O₄体系中掺杂可以显示出明亮的红色发光(发射峰值位于680 nm处)。比较不同Mn⁴⁺浓度(Mn与Al的物质的量之比)掺杂样品的发光强度时发现,Mn⁴⁺最佳掺杂浓度为0.06%。通过德克斯特公式分析了发光强度与浓度关系,探究浓度猝灭机制,结果表明最邻近离子之间能量传递造成Mn⁴⁺浓度猝灭的发生。为了提高Mn⁴⁺的发光强度,选择了7种金属离子(Li⁺、Na⁺、K⁺、Ca²⁺、Sr²⁺、Sn²⁺和Ga³⁺)与Mn⁴⁺共掺杂进入ZnAl₂O₄基质中,其中效果较突出的为Li⁺和Ga³⁺,其共掺杂使Mn⁴⁺发光强度分别增强0.6倍和1倍。     

利用手持技术改进测定乙醇分子结构实验

利用压强传感器代替排水集气法,改进测定乙醇分子结构实验的仪器装置,并探索最佳反应条件。另外,设计两个空白实验,结合压强变化曲线对实验误差进行相关讨论。     

Neutral diterpenoids of oleoresins of five species of conifers of Transcarpathia

The compositions of the neutral diterpenoids of the oleoresins of five species of conifers growing in the Transcarpathia have been studied. It has been found that the oleoresins ofAbies alba M.,Larix decidua M., andPicea excelsa L. contain more than 50% of neutral diterpenoids. The group and qualitative compositions of the oxygen-containing diterpenoids have been determined. In the oleoresins ofAbies alba,Picea excelsa, andPicea abies tertiary alcohols — cis-abienol and isocembrol — predominate, while inLarix decidua the main component is the hydroxy ester larixyl acetate. Primary alcohols related to the resin acids have been found in all the oleoresins investigated. Features of the distribution of diterpenoids according to the species of conifers have been revealed. The results obtained are necessary for the chemotaxonomy of conifers of the family Pinceae.Novosibirsk Institute of Organic Chemistry, Siberian Branch, Academy of Sciences of the USSR. Translated from Khimiya Prirodynkh Soedinenii, No. 6, pp. 812–816, November–December, 1988.     

物质分配系数的测定实验改进

实验教学目的是从解决实际问题出发,以实验技术训练和实验设计思想培养为目标。介绍了将单一的物质分配系数测定实验改进为综合实验,提高了实验效果及实验资源利用率。     

光谱仪测试范围的扩展

由于石化行业的生产需要，其材质的使用具有多样性和广泛性，经常会出现顾客委托的测试样品的一个或几个元素跨越光谱仪现有测试程序测量范围的情况。本法通过对光谱仪测试原理的认识，根据光谱仪的测试能力及标样的采集，实现了一个或几个元素测量范围的扩展，并对其测量的影响因素进行了研究。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Influence of viscosity of medium on processes of oxygen quenching of excited states of mesoporphyrin

The oxygen quenching rate constants for singlet and triplet excited states of the dimethyl ester of mesoporphyrin IX increase with decreasing viscosity of the medium and reach a maximum at a viscosity of approximately 0.4 mPa·sec, after which the rate constants begin to decrease. The drop in rate constant with increasing fluidity of the medium may be related to a nonequilibrium character of the elementary act in the interaction of the reactants in the solvent cage. In viscous media such as isopropyl alcohol, isobutyl alcohol, and isoamyl alcohol, the reaction radius is greater than the sum of the radii of the reacting particles. The long-range character of these processes is due to the relatively weak dependence of the quenching probability on distance.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 25, No. 2, pp. 161–167, March–April, 1989.     

Effect of the Method of Modification of Zeolite X on Selectivity of Catalytic Methylation of Toluene

Theoretical and Experimental Chemistry - The effect of the method of modification of catalysts based on zeolite X by cesium and magnesium cations (ion exchange and impregnation) on the selectivity...