衰荡腔测量中的腔参数选择

 基于谐振腔失调灵敏度参量随腔长的变化关系,提出了一种衰荡腔,它是由共焦腔将腔长缩短为原来的0.73得到的稳定腔。根据光束传输规律和失调腔矩阵方法,以及光腔衰荡法测量原理和曲线拟合方法,建立了腔长、腔镜角度失调下光腔衰荡法的反射率测量模型。通过数值模拟,研究了这种稳定衰荡腔中,腔微小失调对反射率测量结果的影响,并与相同失调情况下共焦衰荡腔的测量结果进行了对比分析。结果表明,这种稳定腔用作衰荡腔,测量结果受腔镜角度失调影响较大,而受腔长失调影响小;其长度较短,便于工程应用;衍射损耗较小,测量精度高。     

一种220 GHz分布作用速调管的高频系统模拟

对一种基于双排矩形波导慢波结构(SDRWS) 结构的3腔EIK进行了详细计算机模拟计算, 通过对基于SDRWS结构的EIK用输入输出腔的S11的模拟计算及对分布作用速调管用中间腔的本征频率的模拟计算, 初步确定了EIK用输入输出腔及中间腔的结构参数, 进而对EIK进行了PIC互作用模拟计算, 结果表明: 该EIK的3dB工作频带为219.5~220.5GHz, 3dB带宽为1GHz, 最大功率为456 W, 最大增益为40.06dB。在此基础上, 通过调整中间腔的波导头宽度以进行参差调谐, 用PIC互作用模型模拟计算研究了中间腔谐振频率对EIK整体性能的影响。结果表明, EIK的3dB工作频带主要由输入输出腔的通频带决定, 而中间腔的谐振频率也具有重要影响。当中间腔的谐振频率分别处于输入输出腔的通频带的低频端或高频端时, 可以使EIK的3dB工作频带向低频端或高频端得到一定程度展宽; 当中间腔的谐振频率高于输入输出腔的通频带的高频端时, EIK的增益在其3dB工作频带内较为平坦, EIK的输出信号在其3dB工作频带内比较稳定, 频谱的纯净程度较好。参差调谐的最终结果表明, 当中间腔的波导头宽度为0.747mm时, EIK获得了接近最优的性能, 3dB工作频带为219.5~220.0GHz, 3dB带宽扩展到1.2GHz, 最大功率为630W, 相应的最大电子效率为11.3%, 最大增益为47dB。     

三维曲面腔顶盖驱动流的MRT-LBM研究

采用多松弛时间格子玻尔兹曼方法(MRT-LBM)的D3Q15模型分别对长方体腔、圆柱腔、半圆柱腔、旋转双曲面腔、旋转椭球面腔、半球腔以及两种组合腔体的三维顶盖驱动腔流进行数值模拟, 比较分析各腔体内流线分布、流速等值线分布和涡心的发展, 对于典型腔体模拟不同雷诺数下的流动情况。结果表明: 在同一雷诺数下, 曲面边界不仅能消除从边界产生的次涡, 还会导致腔内主涡的分离, 增大中心纵剖面纵向回流速度; “上长方体+下半圆柱”腔内流函数分布与边界贴合度最高。当雷诺数不断增大时, 半圆柱腔内主涡逐渐分离成两个同向涡, “上圆柱+下半球”腔内始终保持着圆柱腔与半球腔内的基本流动特征; 而长方体腔内主涡涡心保持在同一高度, 次涡逐渐增强, “上长方体+下半圆柱”腔内流动愈加规则, 主涡逐渐下沉, 流速等值线分布逐渐趋于中心小、四周大。     

Design of a higher harmonic cavity for the SSRF storage ring

Higher harmonic cavity used in the third generation synchrotron light source increases the Touschek lifetime.The higher harmonic cavity of Shanghai Synchrotron Radiation Facility(SSRF)is a 1.5 GHz passive superconducting cavity.Its higher order modes(HOM)are extracted by a ferrite HOM damper out of the cryostat.Multi-cell cavity is chosen concerning the voltage.The harmonic cavity dynamics,beam dynamics with passive harmonic cavity and the design of single cell cavity are included in this paper.     

Fano interference and transparency in a waveguide-nanocavity hybrid system with an auxiliary cavity

We investigate theoretically single photon transport in one-dimensional waveguide coupled to a pair of cavities, which are denoted by the first cavity and the auxiliary cavity. Two cases with no atom and one atom embedded in the first cavity are discussed. The Fano dips in the transmission spectrum and locations of transparency window are calculated. When no atom is embedded in the first cavity, there exists a transparency window under the condition that the first cavity and the auxiliary cavity are not resonant. The locations of the transparency window and Fano line type depend strongly on the eigen frequency of the auxiliary cavity and the coupling strength between the auxiliary cavity and the waveguide. When one atom is embedded in the first cavity, we show that the transparency window exists even though the first cavity, the atom and the auxiliary cavity are resonant. The Fano line type is strongly dependent on the eigen frequency of the auxiliary cavity and the coupling strength. Our results have potential applications in design of quantum devices at the level of single photon,such as single photon switch and single photon routers.     

三腔整管RKA相位的理论与模拟的比较分析

首先采用运动学理论和空间电荷波理论推出了计算中间腔间隙入口处调制电流相位的经验公式。采用调制电子束激励中间腔的非线性理论估算中间腔和输出腔间隙电压的幅度和相位,并提出了估算输出腔间隙入口处调制电流相位的经验公式。采用这些理论和二维粒子模拟比较了中间腔和输出腔间隙入口处调制电流相位、中间腔和输出腔间隙电压相位。中间腔和输出间隙入口处调制电流相位误差为2.627°(模型1)和3.857°(模型2)。中间腔间隙电压幅度的相对误差是1.47%,输出腔幅度的相对误差是5.42%,中间腔相位的误差是4.017°(模型2)和5.427°(模型3),输出腔的相位的误差是12.32°。最后根据二维粒子模拟得出了三种模型调制电流的相位与距离的关系。相关理论计算结果与2D的PIC模拟结果进行了比对,验证了理论估算结果的可信度。     

Acoustic transmission analysis on cavity resonance sound in a cylindrical cavity system: application to a Korean bell

This paper presents an analytical model for acoustic transmission characteristics of a cylindrical cavity system representing the acoustic resonance conditions of a Korean bell. The cylindrical cavity system consists of an internal cavity, a gap, an auxiliary cavity, and a rigid base. Since the internal cavity is connected to the external field through a gap, determination of the acoustic transmission characteristics becomes a coupling problem between the internal cavity and external field. The acoustic field of the internal cavity is considered by expanding the solution method of the mixed boundary problem, and the external field is addressed by modifying the radiation impedance model of a finite cylinder. The analytical model is validated by comparison with both experiment and a boundary element method. Using the analytical model, the resonance conditions are determined to maximize the resonance effect. Thus, the resonance frequencies of the bell cavity system are investigated according to the gap size and auxiliary cavity depth. By adjusting gap size or auxiliary cavity depth, the cavity resonance frequency is tuned to resonate partial tones of the bell sound. Finally, the optimal combination of gap size and auxiliary cavity depth is determined.     

Design of a higher harmonic cavity for the SSRF storage ring

Higher harmonic cavity used in the third generation synchrotron light source increases the Touschek lifetime. The higher harmonic cavity of Shanghai Synchrotron Radiation Facility (SSRF) is a 1.5GHz passive superconducting cavity. Its higher order modes (HOM) are extracted by a ferrite HOM damper out of the cryostat. Multi-cell cavity is chosen concerning the voltage. The harmonic cavity dynamics, beam dynamics with passive harmonic cavity and the design of single cell cavity are included in this paper.     

钕玻璃片状放大器玻璃腔的概念设计

针对片状放大器片腔的洁净度问题,提出一种钕玻璃片状放大器玻璃腔的设计方案.选用滤紫外石英玻璃作为主框架的材料,对玻璃腔的结构和密封方案进行设计,并利用玻璃腔外表面镀金属材料的方式进行遮光.采用神光Ⅱ升级主放和100片状放大器进行不同腔体的洁净度对比试验,结果表明玻璃腔的洁净度较不锈钢腔提高了近70%.运用光学高级系统分析程序对玻璃腔进行光线追迹,其钕玻璃泵浦比例提高了8.84%.该方案不仅能减少腔内气溶胶的产生,还能提高钕玻璃泵浦比例.     

双光子过程耦合腔系统中光场的量子特性

本文研究了双光子过程原子与耦合腔相互作用系统中腔场的压缩效应和反聚束效应.考虑系统总激发数等于2的情况,利用数值计算方法讨论了腔场间的耦合强度变化和原子与腔场间耦合强度变化对反聚束效应的影响.研究结果表明:腔场不呈现出压缩效应;腔场的反聚束效应与原子与腔场的耦合系数之间,以及与腔场间的耦合系数之间都存在着非线性关系,     

Cavity linewidth narrowing and broadening due to competing linear and nonlinear dispersions

We experimentally demonstrate cavity linewidth control by manipulating dispersion of the intracavity medium. By making use of the dramatic change of Kerr nonlinearity near electromagnetically induced transparency resonance in a three-level atomic system, the cavity transmission linewidth can be greatly modified. As the cavity input intensity increases, the cavity linewidth changes from below to above empty cavity linewidth, corresponding to subluminal and superluminal photon propagation in the cavity, respectively.     

Entanglement swapping between atom and cavity and generation of entangled state of cavity fields

This paper proposes a scheme where entanglement swapping between atom and cavity can be realized. \Lambda -type three-level atoms interacting resonantly with cavity field are considered. By detecting atom and cavity field, it realizes entanglement swapping between atom and cavity. It uses the technique of entanglement swapping to generate an entangled state of two cavity fields by measuring on atoms. It discusses the experimental feasibility of the proposed scheme and application of entangled state of cavity fields.     

半导体抽运Yb∶YAG 五镜腔KLM激光器理论分析计算

对半导体抽运的Yb∶YAG克尔透镜锁模激光器进行理论分析计算,分析五镜谐振腔和四镜谐振腔的稳区不同,利用稳区范围变化对五镜谐振腔稳定锁模机理做出合理解释.详细计算分析Yb∶YAG激光器内克尔调制效应对锁模的影响,获得最佳腔参量.在腔内没有插入硬光阑的情况下,利用五镜腔实现了Yb∶YAG晶体克尔透镜锁模运转.理论分析和实验结果相符.     

深度抑制的超导高频腔研究

参照KEKB 509MHz超导腔,同时考虑到许多方面因素的影响,为北京正负电子对撞机改造工程改频设计了一个500MHz超导腔,并且对腔的一些性能进行了模拟计算,同时利用铝模型腔对一些主要参数进行了测量和校核.     

Optical feedback cavity ring-down technique for accurate measurement of ultra-high reflectivity

A novel cavity ring-down (CRD) technique, based on the optical feedback effect of Fabry–Perot diode lasers, is developed for accurate reflectivity measurement of highly reflective cavity mirrors. The strong optical feedback, including the direct reflection from the front cavity mirror of a linear ring-down cavity, is re-injected into the oscillator cavity of the diode laser, and large resonant peaks are observed in the ring-down cavity output signals. The diode laser is switched off by a threshold circuit when the amplitude of a resonant peak exceeds a pre-defined threshold. Exponentially decayed signals recorded immediately after switching off the laser are used to determine the cavity decay time. The ultra-high reflectivity of cavity mirrors is measured to be 99.99606% with a reproducibility of 0.00003%. Compared with the previous phase-shift CRD technique, the signal-to-noise ratio of the cavity output signals is improved with an enhancement factor of over 100.     

FP腔腔长的测量新方法

ＦＰ腔是ＷＤＭ光纤通信系统中用于波长控制和解调的关键器件。为了进行匹配系统的设计以及计算已制成腔的自由谱区，准确测定腔长是必不可少的工作，但是由于ＦＰ腔的具体结构，测定腔长无法用直接的方法进行。本文通过谐振腔的谐振特性分析，推导出一种测量腔长的新方案。     

Generation of a four-atom entangled cluster state in cavity QED

We propose a method of generating a four-atom entangled cluster state by considering two kinds of the atoms–cavity field interaction in cavity QED. During the preparation the cavity is only virtually excited no quantum information will be transferred from the atoms to the cavity and thus the scheme is insensitive to the cavity field states and cavity decay. The scheme can also be used to generate the cluster state for the trapped ions.     

振动不敏感球形光学参考腔研究

本文主要研究用于超稳激光研制的实验室内水平放置的球参考腔的振动敏感度问题.研究了支撑点高度和支撑面积对腔长变化的影响,并讨论了加速度大小的变化对腔长变化的影响.在支撑点完全固定的情况下,振动敏感度被降低到3.0×10-10/g以内.通过大量的数值模拟获得了球参考腔的最佳支撑位置.根据优化的结果提出了这种切割球参考腔放置平台的方案.考虑了加工误差、近水平放置和非对称支撑对参考腔振动敏感度的影响,定量地给出了这三种因素引起的腔长改变量,而且讨论了二阶效应对腔长变化的贡献.     

半导体微腔中腔模、重空穴激子模和轻空穴激子模耦合

采用传输矩阵方法利用半经典的线性色散模型,计算半导体微腔内同时存在重空穴激子、轻空穴激子时,在不同入射角度下的反射谱,同时,利用三简谐振子耦合模型计算了在不同入射角度下,腔模同时和重空穴激子模、轻空穴激子模耦合所形成的三支腔极化激元的能量,以及腔模、重空穴激子模、轻空穴激子模分别在三支腔极化激元中所占的权重,结果表明随着入射角的增加腔极化激元的高能支和两个低能支之间存在明显的反交叉现象,同时,腔模和重空穴激子模、轻空穴激子模在腔极化激元中所占的权重呈现增加或减小的趋势 关键词： 半导体微腔 腔极化激元 激子     

A scheme for implementing quantum game in cavity QED

In this paper, we propose a scheme for implementing quantum game (QG) in cavity quantum electrodynamics(QED). In the scheme, the cavity is only virtually excited and thus the proposal is insensitive to the cavity fields states and cavity decay. So our proposal can be experimentally realized in the range of current cavity QED techniques.