Gain evaluation of compact designing on Er/Yb codoped germanate glass channel waveguide

Bent waveguide structures (U- and F-bend) based on UV-sensitive Er³⁺/Yb³⁺ codoped germanate glass substrates have been designed to achieve high-gain C-band amplification. Using simulated-bend method, the optimal radius for curved structure is offered to be 1.90 cm with loss coefficient of 0.0015 dB/cm, as the substrate size is minimally schemed. In the wavelength range of 1528–1559 nm, obvious gain enhancement for the bent structure waveguides is anticipated, while, for the F-bend waveguide, the internal gain at 1533.8 nm wavelength is derived to be 22.55 dB, which is much higher than the value of 14.06 dB in the U-bend waveguide, and over three times higher than that of the straight one, after compensating both the bend loss and the transition loss. The simulation results indicate that the bent structure designing is beneficial in attaining high optical gain in Er³⁺/Yb³⁺ codoped germanate glass substrates, which assures that long-period grating can be applied to implement practical C-band gain-flattened amplification.     

长波段掺铒光纤放大器用掺铒光纤的设计考虑

本文分析了长波段掺铒光纤放大器(EDFA)的增益系数与Er³⁺离子浓度的关系.研制了铝共掺杂的高浓度掺铒光纤,以缩短长波段掺铒光纤的长度.用两级泵浦实现了L-波段EDFA.光纤放大器的掺铒光纤总长18m,在1570nm波长处的小信号增益为42.26dB,输出功率为17.5dBm.我们认为,较低的浓度淬灭效应归因于光纤中较高的A1掺杂浓度.当总的输入信号功率为-3dBm时,在1570至1600nm间的7路WDM信号的增益不平坦度仅为0.68dB..     

Narrowband phase sensitive fiber parametric amplifier

We describe a widely tunable phase sensitive fiber amplifier, based on narrowband parametric amplification in dispersion shifted fiber. Using a fiber with a zero dispersion wavelength of 1549?nm and a pump wavelength in the range of 1549?nm to 1532?nm, we obtained phase sensitive amplification between 1344?nm and 1781?nm, for an overall wavelength range of 437?nm. The amplifier threshold power is 7?W, and the maximum gain is 50?dB at a pump peak power of 25?W. The variance in gain due to phase sensitivity was measured to be up to 15?dB.     

Brillouin amplification and lasing in a single-mode As2Se3 chalcogenide fiber

Brillouin amplification and lasing are demonstrated in a single-mode As2Se3 chalcogenide fiber. A Brillouin gain of 42 dB was measured in a 4.9 m long fiber for a pump power of 68 mW at a 1.56 mum wavelength. In addition, a compact As2Se3 fiber-based Brillouin laser with a threshold power of 35 mW and a slope efficiency of 38% for nonresonant pumping is demonstrated.     

DESIGN CONSIDERATION OF ERBIUM DOPED FIBER FOR EFFICIENT L-BAND EDFAs

0　Introduction　　Recently,therapidgrowthofInternetanddatacommunicationsserviceshasdriventhedemandforbandwidthinthelong-distancenetworkstodoubleatleasteverytwoyears.Inordertoexploitthelargebandwidthofopticalfiber,technologiessuchaserbium-dopedfiberamplifiers(EDFAs)anddensewavelengthdivisionmultiplexing(DWDM)arewidelyused.Theconventionalwavelengthband(C-band)ofEDFAsextendsfromabout1530to1562nm.Ithasbeenusedforup-to96channelsinDWDMsystem.Itshouldbenotedthatopticalfibernonlineareffectsbe…     

A diode-laser-pumped tunable Ho: YLF laser in the 2 µm region

We report the cw laser emission of Ho: YLF in an astigmatically compensated resonator under pumping by a laser diode array. We measured the laser efficiency at different operating temperatures of the crystal and the non-saturated gain coefficient at the peak wavelength of laser emission. The laser tunability extends from 2.040 µm to 2.075 µm.     

Parametric amplification in a microstructure fiber

We report an observation of parametric amplification with a gain greater than 30 dB in a 1.7-m microstructure fiber. It is found that there exists a peak pump power P_s. For peak pump powers less than P_s, the amplified twin (signal: longer wavelength, and idler: shorter wavelength) pulses are highly correlated, and the bandwidth of the amplified signal pulse broadens monotonically with pump power. For peak pump powers exceeding P_s, the correlation between the amplified twin pulses drops when the pump power increases, the bandwidth of the amplified signal pulse becomes narrower when the pump power increases, and the central wavelength of the amplified signal (idler) pulse shifts towards longer (shorter) wavelength, respectively, due to phase matching. PACS 42.65.Yj     

掺铒光纤激光放大的实验研究

使用自行研制的掺铒光纤维进行了光纤激光放大实验.以Ar~+激光作泵浦,在1.52 μm波长上实现了光放大,增益达10dB以上.绘出了有关掺铒光纤及其光放大的若干实验数据.     

Optical path design and evaluation in Tm doped glass channel waveguide for S-band amplification

To achieve high-gain S-band waveguide amplifiers and promote the practicality of integrated signal amplification devices, bent waveguide structures based on Tm³⁺ doped germanate glass substrate have been designed. Using simulated-bend method, the optimal radius for the curved structure is offered to be 1.90 cm with a loss coefficient of 0.04 dB/cm, as the substrate size is minimally schemed. For the folded-spiral waveguide, the internal gain at 1482 nm is derived to be 13.01 dB, which is higher than the values of 8.21 and 4.22 dB in the U- and S-bend waveguides, respectively, and nearly three times higher than that of the straight one. Simulation results indicate that the optical path design is attractive in realizing the high gain of Tm³⁺ doped germanate glass channel waveguides for practical S-band amplification.     

Double-pass erbium-doped zirconia fiber amplifier for wide-band and flat-gain operations

The double-pass erbium-doped zirconia fiber amplifier (EDZFA) is proposed and demonstrated to provide a wide-band amplification as well as flat-gain operation in both the C- and L-band regions using only a single-gain medium. The proposed amplifier utilizes an erbium-doped zirconia fiber (EDZF) with erbium ion concentration of 2800 ppm as a gain medium. The medium is fabricated in a ternary glass host, zirconia-yttria-aluminum codoped silica fiber through solution doping technique along with modified chemical vapor deposition (MCVD). Compared to a single-pass operation, the double-pass EDZFA shows a better gain performance. At input signal power of 0 dBm and the optimum EDZF length of 2 m, a flat gain of around 16 dB is achieved by the proposed double-pass amplifier with gain variation of approximately 2.5 dB throughout the wavelength range from 1530 to 1590 nm. However, the noise figure of the double-pass amplifier is slightly higher than that of the single-pass due to inefficient population inversion at the input part of the amplifier.     

Nonlinear performances of dual-pump amplifiers in silicon waveguides

The performances of a dual-pump parametric and Raman amplification process and the wavelength conversion in silicon waveguides are investigated. By setting the Raman contribution fraction f to be 0.043 in our analytical model, the amplification gain of the probe signal can be obtained to be over 10 dB. The pump transfer noise (PTN), the quantum noise (QN), and the total noise figure (TNF) are discussed, and the TNF has a constant value of about 4 dB in the gain bandwidth. An idler signal generated during the parametric amplification (PA) process can be used to realize the wavelength conversion in wavelength division multiplexing (WDM) systems. In addition, the pump signal parameters, the generated free carrier lifetime and effective mode area (EMA) of the waveguide are analysed for the optimization of signal gain and noise characteristics.     

~ 1.2 μm near-infrared emission and gain anticipation in Ho doped heavy-metal gallate glasses

Ho³⁺-doped low-phonon-energy heavy-metal gallate glasses (LKBPBG) have been prepared and efficient 1.199 μm emission originating from the ⁵I₆ → ⁵I₈ radiative transition has been observed under 900 nm excitation. The spontaneous emission probability and the maximum stimulated emission cross-section were derived to be 294.31 s^− 1 and 3.46 × 10^− 21 cm², respectively. The ratio of quantum yields between ~ 1.2 and ~ 2.0 μm emissions was identified to be 16%, demonstrating that the ⁵I₆ → ⁵I₈ transition is favorable for optical amplification. The maximum gain coefficient of 1.84 dB/cm at 1.199 μm wavelength was anticipated in the ideal status. These results indicate that the Ho³⁺-doped LKBPBG glasses have a promising potential for the development of ~ 1.2 μm signal amplifier devices.     

Highly efficient short length Bismuth-based erbium-doped fiber amplifier

An efficient 21 cm Bismuth-based erbium doped fiber amplifier (Bi-EDFA) operating in both C- and L-band wavelength regions is proposed and demonstrated. The proposed Bi-EDFA uses the gain medium with an erbium ion concentration of 6300 ppm in conjunction with a double-pass configuration. Compared to conventional silica-based erbium-doped fiber amplifiers (Si-EDFAs) with the same amount of Erbium ions, the Bi-EDFA provides a higher attainable gain as well as a greater amplification bandwidth ranging from 1525 to 1620 nm. The proposed Bi-EDFA achieved a flat-gain of around 23 dB with gain variation of ±3.5 dB within the wavelength region from 1530 to 1565 nm at the maximum pump power of 150 mW. The corresponding noise figures are obtained at an average of 6 dB.     

Performance of optical amplifier employing silica host magnesium-aluminum-germanium co-doped erbium-doped fiber

Two silica host magnesium(Mg)-aluminum(Al)-germanium(Ge) co-doped erbium-doped fibers (EDFs)have been fabricated, which have different Mg concentrations. The concentration of all the compositions in the preform is measured through electronics probe micro analysis (EPMA). The maximum Mg concentrations of fibers A and B are 3.98 and 1.28 mol%, respectively. The performance characteristics including absorption spectrum and gain are measured and analyzed. The absorption coefficients of fibers A and B are 13.3 and 14.3 dB/m respectively at wavelength of 1532 nm. The max gains of these two erbium-doped fiber amplifiers (EDFAs) are 30.1 and 35.9 dB with input signal power of -30 dBm and pump power of 100 mW at 980 nm. Fiber B with maximum Mg concentration 1.28 mol% has better performance than fiber A. Fiber B has high absorption coefficient and high gain characteristics. The optimum fiber B length of C-band EDFA is 7 m and that of L-Band EDFA is about 30 m, which is much shorter than standard commercial EDFAs. The result of experiments showed that a few Mg added to silica host EDF can increase the concentration of erbium ions, which will shorten the EDF length much, but not degrade the performance characteristics.     

双泵浦光子晶体光纤参量放大研究

利用光子晶体光纤在不同零色散波长附近具有不同色散的特性,研究了在零色散波长为780 nm和1550 nm附近的双泵浦光子晶体光纤参量放大过程.在780 nm附近,讨论了零色散波长变化对双泵浦光子晶体光纤参量放大的影响.数值模拟结果表明:当零色散波长发生微小的变化时,信号增益谱带宽会发生很大的变化.当两泵浦光之间的波长差值减小时,零色散波长的变化对参量放大的影响在很大程度上可以得到抑制,但是增益带宽会有一定的减小.依据这一原理,在1550 nm附近设计光子晶体光纤中的色散平坦光纤参量放大,在5 m长的光子晶体光纤中,当峰值功率为10 W时,得到了增益为65 dB,带宽达到420 nm且极为平坦的增益谱.     

Amplification characteristics measurement of 1.55 μm multi-mode LD

The amplification characteristics of 1.55 μm multi-mode LD are presented experimentally. It demonstrates that nine wavelengths across 1547–1557 nm have a good amplification, the maximum gain of ∼43 dB at 1552.14 nm is obtained with pump power of 130 mW @980 nm, and noise figure of ∼5.6 dB at 1554.3 nm is achieved.     

Design of 1480-nm diode-pumped Er3+-doped integrated optical amplifiers

Abstact Erbium-doped Y₂O₃ integrated optical amplifiers are designed for low-threshold operation and 3 dB amplification. The most important design parameter for minimal threshold, the erbium concentration, is found to have an optimum value of 0.35 at% for a given waveguide structure with 1.0 dB cm^-1 background loss. The corresponding threshold power is 7 mW. The pump power to obtain 3 dB gain is found to be 22 mW for an amplifier with an optimum erbium concentration of 0.6 at% and 2.8 cm length. At 30 mW pump power the maximum gain is shown to be 5 dB.Designing is done using a comprehensive numerical model of an erbium-doped integrated optical amplifier. In the model two-dimensional intensity-dependent overlap integrals are used, which allow arbitrary erbium dopant profiles and waveguide crosssections. Concentration-dependent effects such as quenching and upconversion are also included in the model.Input parameters for the model are determined from measurements on an unoptimized Er: Y₂O₃ optical waveguide amplifier. Amplification simulations and gain measurements of the unoptimized waveguides are found to be in close agreement, providing a sound basis for the design calculations.     

Investigation of the optical gain and noise figure for multi-channel amplification in EDFA under optimized pump condition

We present the results of an investigation of optical gain and noise figure for simultaneous multi-channel amplification of an erbium doped fibre amplifier (EDFA) under optimized pump condition. Different pump configurations with varying input signal levels show interesting features on gain flatness. In the experiment, population inversion along the fibre length which determines the gain-spectra and noise characteristics of the amplifier is adjusted through optimized fibre length and injected pump power in order to minimize the gain-tilt at C-band. It is observed that bi-directional pumping manifests the best combination of low noise and high gain of EDFA which are useful as in-line repeaters in WDM network. We obtain 30 ± 1.5 dB intrinsically flat small signal gain from 1538 nm to 1558 nm band of wavelength with noise figure <4 dB for 16-channel simultaneous amplification in a single stage EDFA without gain flattening filter.     

Generation of broadly tunable picosecond mid-infrared laser and sensitive detection of a mid-infrared signal by parametric frequency up-conversion in MgO:LiNbO3 optical parametric amplifiers

Picosecond optical parametric generation and amplification in the near-infrared region within 1.361-1.656 μm and the mid-infrared region within 2.976-4.875 μm is constructed on the basis of bulk MgO：LiNbO 3 crystals pumped at 1.064 μm.The maximum pulse energy reaches 1.3 mJ at 1.464 μm and 0.47 mJ at 3.894 μm,corresponding to a pumpto-idler photon conversion efficiency of 25%.By seeding the hard-to-measure mid-infrared radiation as the idler in the optical parametric amplification and measuring the amplified and frequency up-converted signal in the near-infrared or even visible region,one can measure very week mid-infrared radiation with ordinary detectors,which are insensitive to mid-infrared radiation,with a very high gain.A maximum gain factor of about 7 脳 10 7 is achieved at the mid-infrared wavelength of 3.374 μm and the corresponding energy detection limit is as low as about 390 aJ per pulse.     

Noise characteristics of a high-power ytterbium-doped fibre amplifier at 1083 nm

Experimental results are reported for the noise characteristics of an Yb-doped fibre amplifier pumped at 975 nm, used as a booster of a low-noise narrow-linewidth single-frequency 1083-nm wavelength laser diode. The maximum output power of the amplifier is 1.2 W with a gain larger than 30 dB. An increase of the intensity-noise spectral density relative to the signal, by approximately 6.5 dB, is introduced by the amplification process, due to signal-amplified spontaneous-emission (ASE) beat noise. A remarkable increase of the noise level with decreasing frequency is observed below ≈35 kHz, probably due to technical noise of the amplifier pump diodes. The spectral broadening due to amplifier phase noise was measured to be less than 300 Hz with a 5-kHz-linewidth Nd:YAG laser and that for the 300-kHz-linewidth diode laser at 1083 nm is therefore expected to be in the same range. Received: 5 October 1999 / Revised version: 2 December 1999 / Published online: 24 March 2000