Glassy carbon and boron doped glassy carbon electrodes for voltammetric determination of linuron herbicide in the selected samples

In this study the application of home-made unmodified (GC) and bulk modified boron doped glassy carbon (GCB) electrodes for the voltammetric determination of the linuron was investigated. The electrodes were synthesized with a moderate temperature treatment (1000°C). Obtained results were compared with the electrochemical determination of the linuron using a commercial glassy carbon electrode (GC-Metrohm). The peak potential (E _p ) of linuron oxidation in 0.1 mol dm⁻³ H₂SO₄ as electrolyte was similar for all applied electrodes: 1.31, 1.34 and 1.28 V for GCB, GC and GC-Metrohm electrodes, respectively. Potential of linuron oxidation and current density depend on the pH of supporting electrolyte. Applying GCB and GC-Metrohm electrodes the most intensive electrochemical response for linuron was obtained in strongly acidic solution (0.1 mol dm⁻³ H₂SO₄). Applying the boron doped glassy carbon electrode the broadest linear range (0.005–0.1 μmol cm⁻³) for the linuron determination was obtained. The results of voltammetric determination of the linuron in spiked water samples showed good correlation between added and found amounts of linuron and also are in good agreement with the results obtained by HPLC-UV method. This appears to be the first application of a boron doped glassy carbon electrode for voltammetric determination of the environmental important compounds.      

Determination of linuron in water samples by high performance liquid chromatography after preconcentration with octadecyl silanized magnetite

A sensitive and selective batch adsorption method is proposed for the preconcentration and determination of linuron. Linuron was preconcentrated on octadecyl silanized (ODS) magnetite as an adsorbent and then determined by high performance liquid chromatography (HPLC). Several parameters on the recovery of the analyte were investigated. The experimental results showed that it was possible to obtain sufficient preconcentration efficiency when the solution pH was 6 using 100 mL of sample solution containing 1.0 μg of linuron and 3 mL of ethanol as a desorption solution. Recovery of linuron was 50.7 ± 1.9% with a relative standard deviation for five determinations of 3.0% under optimum conditions. The calibration curve of linuron was linear up to 200 ng mL^− 1 with a correlation coefficient of 0.998 and the detection limit (3S/N) was 1.0 ng mL^− 1. The capacity of the adsorbent was also examined and found to be 0.15 mg g^− 1 for linuron. ODS-magnetite is suitable for repeated use without decreasing recovery at least 4 adsorption–desorption cycles. The proposed method was successfully applied to the determination of linuron in river water with high precision and accuracy.     

Characterization of a carbon paste electrode modified with tripolyphosphate-modified kaolinite clay for the detection of lead

We report about the use of carbon paste electrode modified with kaolinite for analytical detection of trace lead(II) in domestic water by differential pulse voltammetry. Kaolinite clay was modified with tripolyphosphate (TPP) by impregnation method. The results show that TPP in kaolinite clay plays an important role in the accumulation process of Pb(II) on the modified electrode surface. The electroanalytical procedure for determination of Pb(II) comprised two steps: chemical accumulation of the analyte under open-circuit conditions, followed by electrochemical detection of the pre-concentrated species using differential pulse voltammetry. The analytical performance of this system has been explored by studying the effects of preconcentration time, carbon paste composition, pH, supporting electrolyte concentration, as well as interferences due to other ions. The calculated detection limit based on the variability of a blank solution (3s_b criterion) for 10 measurements was 8.4 × 10⁻⁸ mol L⁻¹, and the sensitivity determined from the slope of the calibration graph was 0.910 mol L⁻¹. The reproducibility (RSD) for five replicate measurements at 1.0 mg L⁻¹ lead level was 1.6%. The results indicate that this electrode is sensitive and effective for the determination of Pb²⁺.     

Sensitive determination of 17β-estradiol in river water using a graphene based electrochemical sensor

In this study, a novel material for the electrochemical determination of 17β-estradiol using an electrode based on reduced graphene oxide and a metal complex porphyrin has been applied to environmental monitoring. The electrochemical profile of the proposed electrode was analyzed by differential pulse voltammetry, which showed a shift of the oxidation peak potential of 17β-estradiol to 150 mV in a less positive direction compared to the bare reduced graphene oxide electrode. DPV experiments were performed in PBS at pH 7.0 to determine 17β-estradiol without any previous step of extraction, cleanup, or derivatization, in the range of 0.1–1.0 μmol L⁻¹ with a detection limit archived at 5.3 nmol L⁻¹ (1.4 μg L⁻¹). The proposed sensor was successfully applied in the determination of 17β-estradiol in a river water sample without any purification step and was successfully analyzed under the standard addition method. All the obtained results were in agreement with those from the HPLC procedure.     

Chronopotentiometric analysis of tocopherols using a glassy carbon vessel as the working electrode

Using a specific electrochemical cell with a glassy carbon vessel as the working electrode, a significant enhancement of the chronopotentiometric determination of tocopherols was achieved. Due to the large area of the working electrode, the method sensitivity was increased approximately 50-fold compared to the common electrochemical cell with a glassy-carbon disc electrode. Limits of quantitation of approximately 0.35 mg/dm³ for α-, γ- and δ-tocopherol were obtained. The influence of the most important experimental factors was investigated and the method defined was applied for tocopherol determination in crude vegetable oils. The tocopherol content was determined by standard solutions prepared in a matrix of animal fat. An absolute method for γ- and δ-tocopherol quantitation is also described.     

Application of Novel Zn‐Ferrite Modified Glassy Carbon Paste Electrode as a Sensor for Determination of Cd(II) in Waste Water

This paper describes the preparation of a new sensor based on Zn‐ferrite modified glassy carbon paste electrode and its electrochemical application for the determination of trace Cd(II) ions in waste waters using differential pulse anodic stripping voltammetry (DPASV). Different Zn/Ni ferrite nanoparticles were synthesized and characterized using scanning electron microscopy (SEM) and X‐ray powder diffraction (XRPD). The prepared ferrite nanoparticles were used for the preparation of Zn‐ferrite‐modified glassy carbon paste electrode (ZnMGCPE) for determination of Cd(II) at nanomolar levels in waste water at pH 5. The different parameters such as conditions of preparation, Zn²⁺/Ni²⁺/Fe²⁺ ratio and electrochemical parameters, percentage of modifier, accumulation time, pH and accumulation potential were investigated. Besides, interference measurements were also evaluated under optimized parameters. The best voltammetric response was observed for ZnFe₂O₄ modifier, when the percentage of modifier was 3 %, accumulation time 9 min, pH of supporting electrolyte 5 and accumulation potential ?1.05 V. Thus prepared electrode displays excellent response to Cd(II) with a detection limit of 0.38 ppb, and selective detection toward Cd(II) was achieved.     

Electrochemical determination of arsenite in neutral media on reusable gold nanostructured films

We report a simple and novel method of stirring-only-driven accumulation and electrochemical determination of arsenite (As(III)) with both of the oxidation and reduction peaks associated with As(0)/As(III) using a gold nanofilm electrode in neutral solution. Under stirring, a large amount of As(III) was deposited on the modified electrode and the electrochemical response was greatly amplified. The accumulated As(III) on the electrode showed well-defined redox couple in 0.1 M blank phosphate buffer solution (pH 7.0), which could be used for the measurement of As(III). Under optimal conditions, As(III) could be detected in the range from 0.20 to 375 ppb with a detection limit of 0.04 ppb. In particular, with the use of the reduction peak of As(III) the modified electrode exhibits excellent performance for As(III) determination even in the presence of abundant Cu(II). The regeneration of the electrodes is facile with good reproducibility. The electrochemical system was applied to analyze As(III) in lake water, As(III) spiked tap water and drinking water.     

Determination of Trace Tin by Anodic Stripping Voltammetry at a Carbon Paste Electrode

A sensitive and selective procedure for the determination of trace tin at a carbon paste electrode was described. Each measurement cycle consisted of three steps: accumulation, reduction and stripping. The tin complex with bromopyrogallol red (BPR) was accumulated on the electrode surface in 0.10 mol/L acetate buffer (pH 4.5). After electrochemical reduction of Sn(II) had been carried out, the reoxidation wave of Sn(0) appeared at ?0.69 V (vs. SCE) on scanning the potential in the positive direction in 4.0 mol/L HCl. For a preconcentration time of 2 min, the detection limit was 0.06 μg/L (5×10^?10 mol/L ) and the linear range was from 0.1 to 50 μg/L. The proposed method was applied to the determination of tin in canned food and waste water samples with satisfactory results.     

Determination of azinphos-methyl by adsorptive stripping voltammetry

A very sensitive electrochemical stripping procedure for azinphos-methyl (Guthion) is reported. Accumulation is achieved by adsorption of the compound on a hanging mercury drop electrode. The adsorptive stripping response was evaluated with respect to accumulation time and potential, concentration dependence, electrolyte and other variables. The determination limit is 0.2 ng ml^?1 after 300 s accumulation and 0.4 ng ml^?1 after 180 s accumulation. The procedure was applied to spiked river water.     

Self‐Assembled Monolayer of L‐Cysteine on a Gold Electrode as a Support for Fatty Acid. Application to the Electroanalytical Determination of Unsaturated Fatty Acid

This article describes the formation of a SAM with chemisorbed cysteine to a gold surface by the thiol group to obtain a surface electrode with an amino and an acid group free for later reaction and accumulation with other molecules on the electrode surface. We explore the accumulation of unsaturated fatty acid and the electrochemical response of the electrode after modification with cysteine. The electrochemical study confirmed the accumulation of linoleic acid on the modified electrode. The optimum conditions for the determination of linoleic acid by differential pulse voltammetry of linoleic acid are studied a detection limit (3σ) of 0.03 μg mL^?1 and a determination limit (10σ) of 0.10 μg mL^?1 were obtained and applied to determination in olive oil and ham from Iberian breed hams.     

Electrochemical reduction and voltammetric determination of metronidazole at a nanomaterial thin film coated glassy carbon electrode

Simple and sensitive electrochemical method for the determination of metronidazole, based on a nanostructured film coated glassy carbon electrode (GCE), is described. Multi-walled carbon nanotubes (MWNT) was dispersed into water in the presence of a hydrophobic surfactant to give very stable and homogeneous MWNT suspension, and a MWNT-film coated GCE was achieved via evaporating solvent. Metronidazole yields a well-defined reduction peak whose potential is −0.71 V at the MWNT-film coated GCE in pH 9.0 Britton-Robinson buffer. Compared with bare GCE, the MWNT-film modified GCE significantly enhances the reduction peak current of metronidazole. All the experimental parameters were optimized for the determination of metronidazole. The detection limit is 6×10⁻⁹ mol/l at 2 min accumulation. This method has been successfully used to determine metronidazole in the drugs. Furthermore, results obtained by the proposed method have been compared with spectrophotometric method.     

Electrochemical Determination of Fenitrothion Organophosphorus Pesticide Using Polyzincon Modified‐glassy Carbon Electrode

In this paper, a glassy carbon electrode (GCE) was modified with polyzincon. The modified electrode was used as a simple, inexpensive and highly sensitive electrochemical sensor for the determination of organophosphorus pesticide fenitrothion. To fabricate the electrochemical sensor, GCE was immersed in 0.10 mmol L⁻¹ zincon solutions at pH 7.0 and then successively scanned between −1.00 to 2.20 V (vs . Ag/AgCl) at a scan rate of 70 mV s⁻¹ for six cycles. The morphology and structure of the polyzincon were studied with atomic force microscopy and scanning electron microscopy. A comparison of the electrochemical behavior of fenitrothion on the unmodified and polyzincon modified‐GCE showed that in the modified electrode not only the oxidation peak current increased, but also the overpotential shifted to lower one. The experimental conditions such as sample solution pH, accumulation potential, and time were optimized. The differential pulse voltammetric responses of fenitrothion at potential about −0.60 V was used for the determination of fenitrothion. The peak current increased with increasing the concentration of fenitrothion in the range of 5 to 8600 nmol L⁻¹ with a detection limit of 1.5 nmol L⁻¹. Finally, the electrochemical sensor was used for the analysis of fenitrothion in water and fruit samples.     

Studies on electrochemical behaviors of acyclovir and its voltammetric determination with nano-structured film electrode

A multi-wall carbon nanotubes (MWNTs)-dihexadecyl hydrogen phosphate (DHP) film-coated glassy carbon electrode (GCE) was fabricated, and the electrochemical behaviors of acyclovir on the MWNTs-DHP film-coated GCE were investigated by using cyclic voltammetry (CV), linear sweep voltammetry (LSV), electrochemical impedance spectroscopy (EIS) and chronocoulometry (CC). The oxidation peak current of acyclovir increased significantly and the peak potential shifted negatively at the MWNTs-DHP film-modified GCE, compared with that at a bare GCE. The results showed that this nano-structured film electrode exhibited excellent enhancement effects on the electrochemical oxidation of acyclovir. Consequently, a simple and sensitive electroanalytical method was developed for the determination of acyclovir. The oxidation peak current was proportional to the concentration of acyclovir from 8.0 × 10⁻⁸ to 1.0 × 10⁻⁵ mol/L. The detection limit was about 3.0 × 10⁻⁸ mol/L for 60 s accumulation at 0.00 V. The proposed method was demonstrated by using acyclovir tablets and the result was satisfying.     

Enhanced Specificity and Sensitivity for the Determination of Nickel(II) by Square-wave Adsorptive Cathodic Stripping Voltammetry at Disposable Graphene-modified Pencil Graphite Electrodes

Chemical sensors relying on graphene-based materials have been widely used for electrochemical determination of metal ions and have demonstrated excellent signal amplification. This study reports an electrochemically reduced graphene oxide (ERGO)/mercury film (HgF) nanocomposite-modified pencil graphite electrode (PGE) prepared through successive electrochemical reduction of graphene oxide (GO) sheets and an in situ plated HgF. The ERGO-PG-HgFE, in combination with dimethylglyoxime (DMG) and square-wave adsorptive cathodic stripping voltammetry (SW-AdCSV), was evaluated for the determination of Ni²⁺ in tap and natural river water samples. A single-step electrode pre-concentration approach was employed for the in situ Hg-film electroplating, metal-chelate complex formation, and non-electrolytic adsorption at –0.7 V. The current response due to nickel-dimethylglyoxime [Ni(II)-DMG₂] complex reduction was studied as a function of experimental paratmeters including the accumulation potential, accumulation time, rotation speed, frequency and amplitude, and carefully optimized for the determination of Ni²⁺ at low concentration levels (μg?L^?1) in pH 9.4 of 0.1 M NH₃–NH₄Cl buffer. The reduction peak currents were linear with the Ni²⁺ concentration between 2 and 16?μg?L^?1. The limits of detection and quantitation were 0.120?±?0.002?µg?L^?1 and 0.401?±?0.007?µg?L^?1 respectively, for the determination of Ni²⁺ at an accumulation time of 120?s. The ERGO-PG-HgFE further demonstrated a highly selective stripping response toward Ni²⁺ determination compared to Co²⁺. The electrode was found to be sufficiently sensitive to determine metal ions in water samples at 0.1?µg?L^?1, well below the World Health Organization standards.     

Molecularly imprinted nanoparticles-based electrochemical sensor for determination of ultratrace parathion in real samples

Molecularly imprinted polymer nanoparticles (nano-MIP), containing parathion selective sites, were synthesized by using suspension polymerization in silicon oil and then used for carbon paste electrode preparation. The obtained electrode was applied as an electrochemical sensor for parathion determination in different fruit and vegetable samples. Different factors including electrode composition, conditions of parathion extraction in the electrode and electrochemical measurement conditions were evaluated and then optimized by using various techniques of screening and response surface experimental designs. Electrode response to parathion (Res₁) and its selectivity for parathion (Res₂) were the desired responses. These responses were optimized simultaneously. After optimization, a sensor with high selectivity and picomolar detection limit were obtained. It was shown that the sensor response to parathion concentration was linear in the concentration range of 0.05 to 150?nmol?L^?1. The detection limit of designed sensor was calculated equal to 0.02?nmol?L^?1. The developed determination method was properly used for ultra-trace level assay of parathion in different fruit and cabbage samples.     

Simultaneous UV and electrochemical determination of the herbicide asulam in tap water samples by micellar electrokinetic capillary chromatography

A simple end-column electrochemical detector was designed and attached to an available commercial capillary electrophoresis instrument with UV detection to detect different kind of herbicides and to determinate methyl-4-aminophenyl-sulfonylcarbamate (asulam) in water samples. The designed cell is very easy to assemble and disassemble in a short period of time; the working electrode positioning is also quickly achieved without micropositioners. The alignment between working electrode and capillary outlet was very reproducible for the all checked electrodes; the R.S.D. obtained was lower than 6.0% for 100 μm gap distance. In this mode, the non-electroactive and electroactive compounds could be detected by UV and electrochemical detection, respectively at the same time. The electrochemical determination of asulam using micellar electrokinetic capillary chromatography (MEKC) is the first time that is reported. In both detection systems, a linear range was obtained for asulam concentrations lower than 25.0 mg l⁻¹, in boric acid 0.020 mol l⁻¹ at pH 8.20 and containing 0.025 mol l⁻¹ of sodium dodecyl sulfate, to obtain selectivity additional separation by the micellar distribution process. Under these conditions, an experimental detection limit of 0.4 mg l⁻¹ was achieved. A new experimental scheme is also described for asulam determination in tap waters with a previous preconcentration step. Using both, UV and electrochemical detection, with a previous extraction procedure, the detection limits of asulam in tap water samples were of 1.0 and 0.8 μg l⁻¹, respectively.     

Surfactant-intercalated smectite modified electrode: sensitive electrochemical detection of methyl orange dye

This work describes the use of organosmectite modified electrode to evaluate the electrochemical behaviour and to develop an electroanalytical procedure for the determination of methyl orange (MO) dye in natural water. Organosmectites were prepared by intercalation of hexadecyltrimethylammonium cations at various ratios into the interlayer of smectite. The synthesised organosmectites were characterised by various physicochemical techniques such as Fourier transform infrared spectroscopy, X-ray diffraction, field emission scanning electron microscopy and transmission electron microscopy. An amperometric sensor based on organosmectite as electrode modifier for MO sensing purposes was then evaluated by means of clay-film modified electrode using square wave voltammetry (SWV). The electrochemical procedure for MO analysis by stripping voltammetry involves two successive steps: accumulation of MO at open circuit conditions followed by a voltammetric detection in a same medium by the SWV technique. The peak current obtained (after 5 min preconcentration of 15 µmol L^?1 MO solution) on a glassy carbon electrode coated by a thin film of the modified clay was more than 2.5 times higher than that exhibited by the same substrate covered by a film of the pristine clay. Under optimised conditions, a linear calibration curve for MO was obtained in the concentration range from 0.1 to 1.6 µmol L^?1, leading to a detection limit of 4 × 10^?8 mol L^?1 (signal-to-noise ratio equal to 3). The interfering effect of various inorganic and organic ions likely to influence the stripping determination of the MO was also examined. To further validate application of this sensor, the proposed method was successfully used to the determination of MO in natural water with satisfactory results.     

Electrochemical oxidation behavior of bisphenol A at surfactant/layered double hydroxide modified glassy carbon electrode and its determination

Electrochemical behavior of bisphenol A (BPA) at glassy carbon electrode-modified with layered double hydroxide (LDH) and anionic surfactant (sodium dodecyl sulfate) is investigated by electrochemical techniques. Compared with the bare electrode and LDH-modified electrode, the oxidation peak potential of BPA shifted negatively and the peak current increased significantly due to the enhanced accumulation of BPA via electrostatic interaction with LDH at the hydrophobic electrode surface. Some determination conditions such as LDH loading, pH, scan rate, accumulation potential, and accumulation time on the oxidation of BPA were optimized. And some kinetic parameters were investigated. Under the optimized conditions, the oxidation current was proportional to BPA concentration in the range of 8 × 10⁻⁹ to 2.808 × 10⁻⁶ M with the detection limit of 2.0 × 10⁻⁹ M by amperometry. The fabricated electrode showed good reproducibility, stability, and anti-interference. The proposed method was successfully applied to determine BPA in water samples, and the results were satisfactory.     

Simultaneous trace-levels determination of Hg(II) and Pb(II) ions in various samples using a modified carbon paste electrode based on multi-walled carbon nanotubes and a new synthesized Schiff base

A modified carbon paste electrode based on multi-walled carbon nanotubes (MWCNTs) and 3-(4-methoxybenzylideneamino)-2-thioxothiazolodin-4-one as a new synthesized Schiff base was constructed for the simultaneous determination of trace amounts of Hg(II) and Pb(II) by square wave anodic stripping voltammetry. The modified electrode showed an excellent selectivity and stability for Hg(II) and Pb(II) determinations and for accelerated electron transfer between the electrode and the analytes. The electrochemical properties and applications of the modified electrode were studied. Operational parameters such as pH, deposition potential and deposition time were optimized for the purpose of determination of traces of metal ions at pH 3.0. Under optimal conditions the limits of detection, based on three times the background noise, were 9.0 × 10⁻⁴ and 6.0 × 10⁻⁴ μmol L⁻¹ for Hg(II) and Pb(II) with a 90 s preconcentration, respectively. In addition, the modified electrode displayed a good reproducibility and selectivity, making it suitable for the simultaneous determination of Hg(II) and Pb(II) in real samples such as sea water, waste water, tobacco, marine and human teeth samples.