强度调制532 nm激光水下测距

激光水下探测在水下目标搜寻、资源勘探等领域具有重要的应用,而散射是激光水下探测面临的主要挑战.载波调制激光雷达具有抗散射、抗干扰的优点,本文利用自行研制的532 nm强度调制激光源,在3 m长的水箱中搭建激光水下探测系统. 532 nm激光源最大输出功率为2.56 W,强度调制范围为10.0 MHz—2.1 GHz,光束发散角约0.5 mrad.通过在水箱中添加氢氧化镁(Mg(OH)_2)粉末,测量了不同浑浊度下水的衰减系数.采用相位测距的方法,目标反射光的调制信号为探测信号,对激光源进行调制的电信号作为参考信号,利用相关运算获得激光的延时时间,进而可以获得水下目标的距离.最大调制频率为500 MHz时,实现了距离为4.3个衰减长度目标的探测,测距误差约12 cm.探测距离越远,测距误差越大,调制频率越高,测距精度越高.     

High frequency wavelength modulation spectroscopy with diode lasers

High frequency wavelength modulation spectroscopy with diode lasers is accomplished by dithering the drive current at RF frequencies as high as 250 MHz. This technique is useful for fast and sensitive detection of absorption lines in the near-and mid-infrared spectral regions. Detection of 300 MHz wide spectral features corresponding to 1% changes in transmission is accomplished in time intervals as short as 500 ns. A potential application is for fast reading of information contained in frequency domain optical memories based upon photochemical hole burning.     

Low-frequency fluctuation induced by injection-current modulation in semiconductor lasers with optical feedback

Low-frequency fluctuations in semiconductor lasers with optical feedback are investigated when high-frequency modulation is applied to an injection current. Synchronization of the laser output power with the modulation within +/-3 MHz centered at the frequency corresponding to the external cavity mode was observed. However, for modulation of the detuned frequency from the external cavity mode, low-frequency fluctuations were induced in the laser output power, and these fluctuations were observed within a range of modulation of approximately +/-100 MHz at the center frequency of the external cavity mode.     

Diode-pumped simultaneously Q-switched and mode-locked Nd:GdVO<Subscript>4</Subscript>/LBO red Laser

A diode-end-pumped simultaneously Q-switched and mode-locked intracavity frequency doubled Nd:GdVO₄/LBO red laser with an acousto-optic Q-switch was realized. The maximum red laser output power of 250 mW was obtained at the incident pump power of 8.3 W and the repetition rate of 10 kHz. At 5 kHz, the maximum mode-locking modulation depth of about 80% was achieved with the Q-switched pulse width of 440 ns. The red mode-locked pulse inside the Q-switched pulse had a repetition rate of 115 MHz, its average pulse width was estimated to be about 350 ps.     

电光晶体调谐的外腔反馈半导体激光器

报道一种用电光晶体实现快速调谐和凋制激光频率的方法.在Littrow型外腔反馈半导体激光中插入LiNbO3晶体,利用LiNbO3晶体的电光效应,通过改变晶体电压来调节激光器的有效腔长,可以对激光频率进行快速的调谐和调制.采用该方法,自制外腔反馈半导体激光器的调谐频率可达到2 kHz,它的调谐范围为350 MHz,激光频率调谐系数约为1.06 MHz/V,用饱和吸收光谱观测频率调谐的效果.快速激光频率调制可以应用在稳频技术上,将外腔反馈半导体激光器调制在5～100 kHz频率下,均获得了87Rb原子D2线的饱和吸收光谱的色散信号,并实现了激光频率在饱和吸收峰上的长期稳定.     

窄脉冲相干激光雷达偏频锁定系统仿真研究

鉴于偏频锁定技术在激光外差探测和激光雷达等方面的广泛作用,基于可编程逻辑器件,设计了适用于窄脉冲激光外差信号的偏频锁定控制系统。在设计中,使用超高速电压比较器进行波形变换、多脉冲鉴频和大概率均值滤波进行数字鉴频,采用小步长快速控制方法进行调频,利用数模转换器和线性放大电路输出调频信号。借助信号发生器产生40ns脉宽的模拟外差信号对系统进行了仿真,实现了设计功能。对系统进行鉴频和调频测试,在40ns脉宽时鉴频误差范围为-7.5MHz～+7.7MHz。     

Broadband amplitude-modulated laser source with high output power for FM/cw lidar transmitter

We are building a long-range FM/cw nonscanning imaging lidar breadboard. This lidar system achieves ranging based on a frequency modulation/continuous wave (FM/cw) technique, implemented by an amplitude modulated mid-IR diode laser transmitter with a linear frequency modulation (LFM) of the subcarrier. Firstly, various schemes of light beam modulation are analyzed. Secondly, we put forward a laser modulation scheme whose core was formed by a 1.55 μm electro-absorption modulated laser diode (EML) and an erbium-doped optical fiber amplifier (EDFA), then a corresponding experimental system architecture and components for light beam modulation and detection are established. Finally, a corresponding experiment of laser beam modulation is completed for the first time. In our experiment, the EML amplitude is modulated by a 200 MHz to 800 MHz LFM signal, whose amplitude value is 2.05 V. The average output power of the modulated laser obtained in the experiment is 10 W, peak power is 16.4 W, and the average modulation depth is 78%. The results of tests predict that this laser modulation scheme is likely to improve the imaging range of the FM/cw lidar.     

Frequency (250 MHz to 9.2 GHz) and viscosity dependence of electron spin relaxation of triarylmethyl radicals at room temperature

Electron spin relaxation times for four triarylmethyl (trityl) radicals at room temperature were measured by long-pulse saturation recovery, inversion recovery, and electron spin echo at 250 MHz, 1.5, 3.1, and 9.2 GHz in mixtures of water and glycerol. At 250 MHz T(1) is shorter than at X-band and more strongly dependent on viscosity. The enhanced relaxation at 250 MHz is attributed to modulation of electron-proton dipolar coupling by tumbling of the trityl radicals at rates that are comparable to the reciprocal of the resonance frequency. Deuteration of the solvent was used to distinguish relaxation due to solvent protons from the relaxation due to intra-molecular electron-proton interactions at 250 MHz. For trityl-CD(3), which contains no protons, modulation of dipolar interaction with solvent protons dominates T(1). For proton-containing radicals the relative importance of modulation of intra- and inter-molecular proton interactions varies with solution viscosity. The viscosity and frequency dependence of T(1) was modeled based on dipolar interaction with a defined number of protons at specified distances from the unpaired electron. At each of the frequencies examined T(2) decreases with increasing viscosity consistent with contributions from T(1) and from incomplete motional averaging of anisotropic hyperfine interaction.     

Measurement of elastic nonlinearity using remote laser ultrasonics and CHeap Optical Transducers and dual frequency surface acoustic waves

A nonlinear ultrasonic technique for evaluating material elastic nonlinearity has been developed. It measures the phase modulation of a high frequency (82MHz) surface acoustic wave interacting with a low frequency (1MHz) high amplitude stress inducing surface acoustic wave. A new breed of optical transducers has been developed and used for the generation and detection of the high frequency wave. The CHeap Optical Transducer (CHOT) is an ultrasonic transducer system, optically activated and read by a laser. We show that CHOTs offer advantages over alternative transducers. CHOTs and nonlinear ultrasonics have great potential for aerospace applications. Results measuring changes in ultrasonic velocity corresponding to different stress states of the sample are presented on fused silica and aluminium.     

光纤移频分布式布里渊光纤传感技术

提出了一种利用布里渊光纤环形腔移频技术实现分布式光纤布里渊传感的方法.该方法基于布里渊光时域分析法原理,将一束单纵模运转激光器输出的激光分为两束|一束光入射布里渊光纤环形腔中产生窄线宽的受激布里渊散射光作为斯托克斯光,另一束光经过低频相位调制后作为泵浦光|斯托克斯光和泵浦光分别相向入射进入传感光纤,通过测量布里渊谱得到光纤温度或应变.利用该方法可将十几GHz的微波频率转化为兆赫信号频率进行探测处理,仅需一台激光器,因此系统结构简单、成本低,还可减小激光器频率波动对测量准确度的影响.实验验证了该方法的可行性.     

基于1.6μm甲烷气体吸收线的半导体激光器频率稳定性分析

利用波长调制技术以及数字PI控制器将外腔二极管激光器（ECDL）稳定到1.6 μm处的甲烷气体吸收线上.稳定后的激光频率波动小于5.6 MHz,相对于自由运转时的160 MHz有了很大提高, 而误差信号的Allan方差均方根（即稳定度）在平均积分时间为64 s时达到最小值1.66×10－11.从理论上定性分析了频率稳定度受到的各种限制因素,最后得出本实验中频率稳定度主要受频率调制和探测器噪声限制的结论,同时给出了提高频率稳定度的方法.被稳定的激光器主要用于为甲烷气体浓度监测提供频率参考.     

基于PSpice的半导体激光高频调制系统设计

为了实现高频率的调制激光输出,设计了一种驱动系统由信号放大、电流调制、过流保护和具有慢启动功能的直流偏置电路高度集成的半导体激光高频调制系统。此系统采用了结构简单的直接调制方式,运用线性调频的高频信号去控制半导体激光器发射激光的强度,从而实现高频调制。在运用OrCAD/PSpice对高频调制驱动系统进行模拟仿真的基础上,最终研制出的半导体激光高频调制系统实现了频率为40.02 MHz、直流偏置为493.326 mA、正弦波调制电流峰峰值为850 mA的高频调制输出,调制激光平均功率为300 mW。     

Frequency stabilization of diode laser to 1.637μm based on the methane absorption line

The frequency of an external-cavity diode laser has been stabilized to 1.637 μm by using the reference of absorption lines of methane.The method can be applied to wavelength division multiplexed optical communication,fiber-optic sensing systems,as well as the high-sensitivity detection of methane.The derivative-like error signal yielded by frequency modulation and phase sensitivity detection technology is inputted into the PI feedback loop circuit in order to stabilize the frequency to the line center.After stabilization,the frequency fluctuation of diode laser is held within 5.6 MHz,and the root of Allan variance of error signal reaches a minimum of 1.66×10-10 for an average time of 10 s.     

Some effects of auditory grouping factors on modulation detection interference (MDI).

The ability to detect the existence of amplitude modulation at a target frequency is reduced when amplitude modulation exists at a flanking frequency. This effect has been termed modulation detection interference (MDI) [Yost and Sheft, J. Acoust. Soc. Am. 85, 848-857 (1989)]. One explanation for MDI holds that the masking and target frequencies are grouped together by the auditory system such that it is difficult to analyze the modulation at each frequency separately. The present study investigated conditions where the asynchrony of temporal gating of the target and flanking frequencies was manipulated in order to make the frequencies more or less likely to be grouped together by the auditory system and perceived as originating from a single putative source. A second experimental manipulation attempted to perceptually segregate the masking and target frequencies on the basis of harmonicity or spectral proximity. The results of the experiments indicated that manipulations that were intended to enhance the segregation of the masking and target frequencies reduced the magnitude of MDI effects. This generally supported an interpretation that MDI is related in some way to auditory grouping. A final experiment was performed in which the subject had to detect the presence of amplitude modulation, but also had to identify which of two frequency components carried the modulation. Subjects were often poor in discriminating which of two frequencies was amplitude modulated, even when the modulation itself was clearly audible. It was concluded that part of the MDI effect might be due to the poor ability of the auditory system to associate modulation with the carrier of the modulation.(ABSTRACT TRUNCATED AT 250 WORDS)     

Rb saturation spectroscopy with an optically narrowed FM diode laser

A fast-frequency modulated (FM) diode laser has been optically narrowed using the technique of resonant optical feedback, to provide linewidths in each FM mode of ≈ 200 kHz peak-to-peak. With a drive frequency of 50 MHz and modulation index of 0.2, the FM laser has been used for the first time to obtain Doppler-free FM spectra of the Rb D₁ line at 795 nm. The potential use of this system for laser frequency stabilisation is discussed.     

A rapid,spatially dispersive frequency comb spectrograph aimed at gas phase chemical reaction kinetics

This New Views article will highlight some recent advances in high sensitivity gas detection using direct infrared absorption frequency comb laser spectroscopy, with a focus on frequency comb use in chemical reaction kinetics and our own contribution to this field. Our recently implemented detection technique uses a combination of a 12.9?GHz free spectral range virtually imaged phased array and diffraction grating to spatially disperse the mid-infrared frequency comb onto a camera. Individual frequencies or ‘comb teeth’ of a 250?MHz repetition-rate frequency comb are able to be resolved. High molecular sensitivity is achieved by increasing the interaction path length using a Herriott multipass cell. High spectral resolution, broadband spectral coverage, and high molecular sensitivity are all achieved on an adjustable 1–50 µs timescale, making this frequency comb apparatus ideal for measuring chemical reaction kinetics where multiple absorbing species can be monitored simultaneously. This New Views article will also discuss some of the challenges and decisions that chemists might face in implementing this advanced physics technology in their own laboratory.

Spatially dispersed 250 MHz mid-infrared frequency comb laser, with absorption of some frequencies by a dilute sample of methane.     

Coherent-burst laser ranging: decoupling resolution and unambiguous range

A novel signal encoding and decoding method for laser ranging is proposed and experimentally demonstrated. The coherent-burst method uses a quasi-continuous interrupted burst of modulated laser radiation to achieve high-precision ranging at all distances. Both time of flight and phase shift are determined based on an amplitude-modulation pattern that has electronic coherence with a master oscillator. High-frequency modulation provides high absolute precision, while measured temporal delay from transmission to reception eliminates potential uncertainty from aliasing. The method is demonstrated with low-power diode lasers that can be modulated at frequencies in excess of 250 MHz.     

大功率半导体激光调制系统及内部调制特性

从半导体激光直接调制理论出发,对直接调制过程中影响半导体激光器高频调制性能的因素进行了研究;运用PSpice建立半导体激光器等效电路模型,仿真研究了电学寄生参数对半导体激光器调制特性的影响且提出了相应的提高其调制性能的方法。在研究半导体激光器调制特性的基础上,设计了一种半导体激光直接调制系统。运用OrCAD/PSpice对直接调制驱动系统进行仿真。研制的半导体激光调制系统实现了频率为1 MHz、平均功率为1.1 W的调制激光输出。     

Delay self-heterodyne measurement of narrow linewidth laser frequency drift characteristic

Resonator integrated optic gyro (RIOG), which employs narrow linewidth laser, is a high-accuracy inertial rotation sensor based on the Sagnac effect. The performance of RIOG is greatly affected by the frequency drift of narrow linewidth laser. A simple, effective method to measure the relative frequency drift of narrow linewidth laser based on delayed self-heterodyne technique is proposed in this paper. The measurement range and sensitivity can easily be satisfied by setting the length difference of the fiber segments between two interferometer arms. The relationship between the length difference and the frequency drift is derived based on the given principle of measuring the relative frequency drift. Then the laser frequency drift measuring setup is established and the experiment results demonstrate that a center frequency drift rate is less than 2 MHz/6.7 s under the room-temperature. Moreover, the measuring setup is applied to test the modulation coefficient of piezoelectric-transducer (PZT), and the modulation coefficient of 9.62 MHz/V is obtained, which satisfies the requirements of RIOG closed-loop operation.     

Frequency modulated and polarization maintaining fiber laser with narrow linewidth

A novel configuration of fiber laser with frequency modulation is presented. Frequency modulation, stable polarization state and narrow linewidth are realized by using the waveguide phase modulator, polarization maintaining devices and saturable absorber. It is shown that the laser output reaches 23 mW, linewidth is less than 1 kHz, polarization extinction ratio is higher than 20 dB and maximum value of frequency deviation can reach 7.5 MHz.