Etch Induction Time in CR-39 Detectors Etched in Na2CO3 Mixed NaOH Solution

Six different solutions of 6M NaOH, containing different amounts of Na2CO3 at 70℃ were used for the revelation of latent damage trails in CR-39 plastic track detectors. These detectors were earlier exposed to fission fragments from ^252 Cf source for 30 min in vacuum and were then etched in the respective solutions for different etching time intervals of 5-20 min starting from 5min up to 160min. The etch induction time in each detector was obtained by extrapolating the intersection of resulting curves of track lengths and track diameters with the time axis.     

Etchability of Latent Fission Fragment Tracks in CR-39

We report the chemical etching behaviour of the CR-39 polymer detector exposed to fission fragments of 252Cf describing etchability of latent tracks, which are like nanocylinders. The fission fragment exposed detectors were etched in 1-7 N NaOH water solutions at temperatures 50-80℃ for 45 min in the case of track length and 180 min in the case of track diameter measurements. The reduced etch rate S （called here etchability） is determined using experimental results for all etching conditions and the etching conditions with the highest reduced etch are obtained. Physics and energetics of bulk and track etching are discussed. Possible effects causing spurious changes in determination of activation energy of etching are investigated.     

Fission studies of gold induced by (1665 MeV) π- using a CR-39 detector

The fission cross section and fission probability of ¹⁹⁷Au, induced by (1665 MeV) π^-, have been studied using CR-39 track detectors. A 4π-geometry was used to count track statistics. A beam of negative pions of 1665 MeV was produced at AGS of Brookhaven National Laboratory, USA, and allowed to fall normally on the stack. Two detectors from the stack were scanned for fission fragment tracks after etching in 6N NaOH at 70℃. The statistics of fission fragment tracks in both detectors were obtained. It was found that there was a marked asymmetry of registered tracks with respect to the forward and backward hemispheres. This asymmetry could be partly accounted for on the basis of momentum transfer to the struck nucleus. On the basis of counting statistics fission cross section was measured, and fission probability was determined by dividing the fission cross section with the reaction cross section. The fission cross-section and fission probability were compared with the computed values using the cascade-exciton model code CEM95.     

Calibration Experiments for Identification of Space Heavy Ions by CR-39

A subject “Study of mechanism and application of space radiation induced mutation breeding on rice“ has been established in NSFC, China. In order to verify space heavy particles being main cause (in addition, microgravity, vacuum, magnetic field etc.) of induced biological effects in space and in order to study correlation of various mutation and its serious degree with different particle parameters, measurement and identification of the particles are necessary. CR-39 sheets are a part of a sandwich detecting system. The system consists of rice seeds and CR-39 solid state nuclear track detectors. The seeds hit by space particles could be determined withetched tracks in CR-39. Furthermore, the space heavy particles could be identified with measured parameters of the tracks such as residual range and etch rate.     

Micro-track structure analysis for 100 MeV Si ions in CR-39 by using atomic force microscopy

To analyze the micro-track structure of heavy ions in a polymer material,parameters including bulk etch rate,track etch rate,etch rate ratio,and track core size were measured.The pieces of CR-39 were exposed to 100 MeV Si ions with normal incidence and were etched in 6.25N NaOH solution at 70 C.Bulk etch rate was read out by a profilemeter after several hours of etching.The other parameters were obtained by using an atomic force microscope(AFM)after a short time of etching.We have measured the second etch pits and minute etch pits to obtain the track growth curve and three dimension track structures to track the core size and etch rate measurements.The local dose of the track core was calculated by theδ-ray theory.In our study,we figure out that the bulk etch rate Vb=(1.58±0.022)μm/h,the track etch rate Vt=(2.90±0.529)μm/h,the etch rate ratio V=1.84±0.031,and the track core radii r≈4.65 nm.In the meantime,we find that the micro-track development violates the traditional track-growth model.For this reason,a scenario is carried out to provide an explanation.     

An Atomic Force Microscopy Investigation of the Tracks Made by C1^＋－C4^＋ Bombardment on CR－39 Detectors

Carbon micro-clusters are accelerated by an HI-13 tandem accelerator. The plastic nuclear track detectors CR-39are irradiated by C1-C4 beams from the HI-13 tandem accelerator and the tracks in CR-39 are studied using anatomic force microscope (AFM). The depths and diameters of C1-C4 tracks are measured for the first time in ananometre scale. An enhancement of the energy loss is obtained for carbon clusters related to single carbon ionswith the same velocity. The results show that the AFM observation is very useful in the quantitative analysis ofclusters in the track detector CR-39.     

Annihilation of Antiprotons in Light Nuclei

CR-39 detectors have been exposed to a 5.9-MeV antiproton beam using the low energy antiproton ring （LEAR） facility at CERN. At this energy, tracks of antiprotons appear in a CR-39 detector after 135 rain of etching in 6M NaOH at 70℃. Fluence of the antiproton beam has been determined using track density. We have also found tracks in the etched CR-39 detector at different depths （250-500μm）. These tracks have resulted from the annihilation of antiprotons with the constituents （H, C and O） of the CR-39 detector. The goal of the experiment is to develop a simple and low-cost method to study properties of antiparticles and those formed after annihilation of these particles with the target matter.     

Generation of fast protons in moderate-intensity laser－plasma interaction from rear sheath

Forward fast protons are generated by the moderate-intensity laser--foil interaction. Protons with maximum energy 190~keV are measured by using magnetic spectrometer and CR-39 solid state track detectors along the direction normal to the rear surface. The experimental results are also modeled by the particle-in-cell method, investigating the time-varying electron temperature and the rear sheath field. The temporal and spatial structure of the sheath electrical field, revealed in the simulation, suggests that these protons are accelerated by target normal sheath acceleration (TNSA) mechanism.     

Spontaneous Fission Barriers Based on a Generalized Liquid Drop Model

The barrier against the spontaneous fission has been determined within the Generalized Liquid Drop Model （GLDM） including the mass and charge asymmetry, and the proximity energy. The shell correction of the spherical parent nucleus is calculated by using the Strutinsky method, and the empirical shape-dependent shell correction is 6mp10yed during the deformation process. A quasi-molecular shape sequence has been defined to describe the whole process from one-body shape to two-body shape system, and a two-touching-ellipsoid is adopted when the superdeformed one-body system reaches the rupture point. On these bases the spontaneous fission barriers are systematically studied for nuclei from 2a~Th to 249 Cm for different possible exiting channels with the different mass and charge asymmetries. The double, and triple bumps are found in the fission potential energy in this region, which roughly agree with the experimental results. It is found that at around Sn-like fragment the outer fission barriers are lower, while the partner of the Sn-like fragment is in the range near l~SRu where the ground-state mass is lowered by allowing axially symmetric shapes. The preferable fission channels are distinctly pronounced, which should be corresponding to the fragment mass distributions.     

Relativistic Energy Pb Projectile Fragmentation with Heavy Target Nuclei

We investigate the fragmentation of 158A GeV ^207Tpb projectiles with Bi, Pb, Cu and AI targets using CR-39 nuclear track detectors. The exposures were made at SPS-CERN. After the etching, the detectors were scanned using an optical microscope to collect the data of etched cone diameters and lengths. We measured the partial charge-changing cross sections using the data of etched cone lengths. The predicted cross sections are compared to similar measurements reported in literature and their dependences on projectile and target mass are described.     

The fragmentation of 20Ne at 400 A MeV

The total charge-changing cross sections and partial cross sections for the production of projectile fragments are measured in the interactions of 400 A MeV ²⁰Ne with aluminum, carbon and polyethylene targets sandwiched with CR-39 plastic nuclear track detectors. The measured total charge-changing cross sections are compared with the predictions using the Bradt-Peters semi-empirical formula, and the NUCFRAG2 and PHITS models. It is shown that the measured experimental results are in good agreement with the theoretical model prediction and other experimental results, and it can be clearly seen that the partial cross sections for fragment production show obvious odd-even effects.     

Inter-relationship of Various Results in Analysis of （14.0 MeV／U） Pb＋Pb Reaction Using Mica and CN-85 Track Detectors

Two detector materials mica and cellulose-nitrate(CN)-85 have been used to study (14.0MeV/u) Pb Pb reaction. Events of different multiplicities were registered in mica and CN-85 detectors using the 2π-geometry technique of solid state nuclear track detection. After removing the target material from the detectors the damaged trails in the detectors were revealed as tracks by proper chemical etching. The irradiated area of each sample was scanned and events of different multiplicities were traced. The binary events were bifurcated into elastic and inelastic events. The elastic binary events and three prong events, observed in the reaction, have been used to search out coefficients Cμv in the presence of both the detectors, for the reaction under study. Using these coefficients 3- and 4-prong events have been analysed. From the detailed analysis of the results of (14.0MeV/u) Pb Pb reaction, obtained from mica and CN-85 track detectors we observed a great resemblance of results obtained from the two detectors. Combining the results of both the detectors, we report some important outcomes.     

Multi-modal analysis for low energy neutron-induced fission of 235U

Low energy neutron induced fission of 235U is studied in the framework of the multi-modal fission model. The fission fragment properties, such as the yields, the average total kinetic energy distribution and the average neutron separation energy, are investigated for incident neutron energies from thermal to 6.0 MeV. The multi-modal fission approach is also used to evaluate the prompt fission neutron multiplicity and spectra for the neutron-induced fission of 235U with an improved version of the Los Alamos model for incident neutrons below the （n, nf） threshold. The three most dominant fission modes are taken into account. The model parameters are determined on the basis of experimental data. The calculated results are in good agreement with the experimental data.     

Calculation of prompt fission neutron spectra for 235U(n,f)

The prompt fission neutron spectra for the neutron-induced fission of ²³⁵U at E_n < 5 MeV are calculated using nuclear evaporation theory with a semi-empirical model, in which the nonconstant and constant temperatures related to the Fermi gas model are taken into account. The calculated prompt fission neutron spectra reproduce the experimental data well. For the n(thermal)+²³⁵U reaction, the average nuclear temperature of the fission fragment, and the probability distribution of the nuclear temperature, are discussed and compared with the Los Alamos model. The energy carried away by γ rays emitted from each fragment is also obtained and the results are in good agreement with the existing experimental data.     

Multi-modal calculations of prompt fission neutrons from 238U（n,f） at low induced energy

Properties of prompt fission neutrons from ²³⁸U(n, f) are calculated for incident neutron energies below 6 MeV using the multi-modal model, including the prompt fission neutron spectrum, the average prompt fission neutron multiplicity, and the prompt fission neutron multiplicity as a function of the fission fragment mass υ(A) (usually named “sawtooth” data) The three most dominant fission modes are taken into account. The model parameters are determined on the basis of experimental fission fragment data. The predicted results are in good agreement with the experimental data.     

Mechanism of amorphous Ge2Sb2Te5 removal during chemical mechanical planarization in acidic H2O2 slurry

In this paper, chemical mechanical planarization (CMP) of amorphous Ge2Sb2Te5 (a-GST) in acidic H2O2 slurry is investigated. It was found that the removal rate of a-GST is strongly dependent on H2O2 concentration and gradually increases with the increase in H2O2 concentration, but the static etch rate first increases and then slowly decreases with the increase in H2O2 concentration. To understand the chemical reaction behavior of H2O2 on the a-GST surface, the potentiodynamic polarization curve, surface morphology and cross-section of a-GST immersed in acidic slurry are measured and the results reveal that a-GST exhibits a from active to passive behavior for from low to high concentration of H2O2 . Finally, a possible removal mechanism of a-GST in different concentrations of H2O2 in the acidic slurry is described.     

The quantum cocktail party problem

The cocktail party problem is a selective attention problem in classical information processing,which has been extensively studied in computer science and neuroscience for decades.It considers the scenario in which signals are emitted from several different independent sources,and detectors detect different mixings of these signals,and target the recovery of individual sources from the information of detectors,regardless of how these signals are mixed as a prior.     

β-delayed fission of 228Ac

The basic process of an exotic decay mode namely β-delayed fission is simply introduced. The progress status of the study in the world is essentialized. The observation of β-delayed fission of ²²⁸Ac is reported. The radium was radiochemically separated from natural thorium. Thin Ra sources in which ²²⁸Ac was got through ²²⁸Ra →β^－228Ac were prepared for observing fission fragments from β-delayed fission of ²²⁸Ac. They exposed to the mica fission track detectors, and measured by an HPGe γ-ray detector. The β-delayed fission events of ²²⁸Ac were observed and its β-delayed fission probability was found to be (5±2)×10^－12.     

Multi-parameter global calculations of fission fragments using a simplified two-dimensional scission-point model

Exploiting the concept of the dinuclear system,the interaction potential energy of two fragments that are quite close to each other is analyzed.A semi-classical method is used to calculate fission fragment yields using a simplified two-dimensional scission-point model.By considering the tip-to-tip orientation at the scission point of the fission process,we investigate the mass,charge,and kinetic-energy distributions of the fission fragments,for excitation energies in the 0-20 MeV range.Our results show that the fission fragment distributions are reproduced quite well,including the recent experimental results for the isotone chain[D Ramos et al.Phys.Rev.C 97,054612(2018)].Thus,the simplified model is useful for multi-parameter global measurements of fission products.     

Position reconstruction in fission fragment detection using the low pressure MWPC technique for the JLab experiment E02-017

When a Λ hyperon is embedded in a nucleus it can form a hypernucleus. The lifetime and its mass dependence of stable hypernuclei provide information about the ΛN interaction in the nuclear medium. This work will introduce the Jefferson Lab experiment (E02-017), which aims to study the lifetime of the heavy hypernuclei using a specially developed fission fragment detection technique: a multi-wire proportional chamber operating under low gas pressure (LPMWPC). The trajectory of the detected fragment is reconstructed and used to find the fission point on the target foil, the position resolution is less than 1 mm, which meets the original design, the separation of target materials and events mixture percentage in different regions are verified by Monte Carlo simulation.