Self-assembly of inner skin hollow fiber polyelectrolyte multilayer membranes by a dynamic negative pressure layer-by-layer technique

In the past studies, electrostatic layer-by-layer (LbL) adsorption of oppositely charged polyelectrolytes has proven to be a promising method for the preparation of polyelectrolyte multilayer membranes (PEMMs). Till now, this method was mainly used to assemble flat sheet and tubular membranes. Since hollow fiber membrane has some advantages such as high-packing density, self-contained mechanical support and hence the consequent economical superiority, this study therefore seeked to assemble inner skin hollow fiber PEMMs by using a dynamic LbL adsorption technique. The assembly process was successfully accomplished by alternatively dynamically filtrating polyacrylic acid (PAA) and polyethyleneimine (PEI) on a hydrolyzed hollow fiber polyacrylonitrile (PAN) membrane under a negative pressure condition. In the case of pervaporation separation of 95 wt.% ethanol–water mixture (50 °C), the membrane obtained with only 4.5 and 6.5 bilayers had separation factor of 245 and 1338 while the permeate fluxes were 290 and 120 g/(m² h), respectively. The pervaporation separation behavior of various alcohol/water mixtures with the alcohols being t-butanol, 2-propanol and ethanol were also investigated. Finally, scanning electron microscopy and atomic force microscopy clearly confirms a uniform and defect-free layer formed on the inner surface of hollow fiber support. Since different polyelectrolyte pairs could be used to assemble PEMMs for different uses, it was expected that the dynamic negative pressure LbL adsorption technique could also potentially be used to prepare many types of PEMMs in other fields.     

聚电解质PDDA/PSS层层自组装膜的渗透汽化性能

采用聚电解质层层自组装(LbL)技术, 在不同盐浓度下制备了聚(二烯丙基二甲基氯化铵)/聚苯乙烯磺酸钠(PDDA/PSS) 多层自组装膜, 并用于渗透汽化性能的研究. 重点考察了组装溶液中NaCl的浓度、组装层数及操作温度对自组装膜的异丙醇脱水性能的影响. 同时, 用扫描电镜观测了不同条件下制备膜的表面形貌. 结果表明, 在高NaCl含量的聚电解质溶液中只需组装几个双层的LbL膜, 即能获得较高的分离因子和较大的通量, 并解释了该LbL膜呈现反“trade-off”现象的原因.     

Polyelectrolyte layer-by-layer self-assembly enhanced by electric field and their multilayer membranes for separating isopropanol–water mixtures

An electric field enhanced method is developed for fabricating layer-by-layer (LbL) self-assembly polyelectrolyte multilayer membranes. Three kinds of electric field enhanced polyelectrolyte multilayer membranes (EPEMs), poly(diallyl dimethylammonium chloride)/poly(styrenesulfonate sodium salt) (PDDA/PSS), poly(diallyldimethylammonium chloride)/poly(acrylic acid sodium salt) (PDDA/PAA) and polyethylenimine/poly(acrylic acid sodium salt) (PEI/PAA), were self-assembled on a reverse osmosis membrane (ROM). The pervaporation performances of EPEMs for separating isopropanol–water mixtures (90/10, w/w) are all superior to those of corresponding normal self-assembled polyelectrolytes membranes (PEMs), and the selectivity increases with PDDA/PSS, PDDA/PAA and PEI/PAA in order. For (PEI/PAA)₄PEI EPEM, the separation factor is 1075 and permeation flux is 4.05 kg m⁻² h⁻¹ at 70 °C. This novel method speeds up the LbL process, which makes it promising for the practical application of the LbL multilayer membrane.     

氧化石墨烯/聚电解质层层自组装制备单价离子选择性膜

采用层层自组装法在改性聚丙烯腈(PAN)膜表面交替沉积聚乙烯亚胺(PEI)和聚丙烯酸-氧化石墨烯(PAA-GO)混合液,制得了单价离子选择性复合膜。X射线衍射(XRD)测试结果表明成功合成了氧化石墨烯(GO)并在复合膜中均匀分散。扫描电镜(SEM)观察结果证实了多层聚电解质PEI/PAA-GO成功地组装在基膜上,并用紫外-可见(UV-Vis)光谱进一步证实了组装过程的均匀性和连续性。接触角和性能测试表明加入GO后,复合膜的亲水性和单价阳离子的选择性明显增大。这种高通量、高选择性的防污复合膜在分离和水的软化方面有很好的应用前景。     

Pervaporation separation of water + isopropanol mixtures using novel nanocomposite membranes of poly(vinyl alcohol) and polyaniline

Novel nanocomposite polymeric membranes containing nanosized (30–100 nm) polyaniline (PANI) particles dispersed in poly(vinyl alcohol) (PVA) were prepared and used in the pervaporation separation of water–isopropanol feed mixtures ranging from 10 to 50 mass% of water at 30 °C. Of the three nanocomposite membranes prepared, the membrane containing 40:60 surface atomic concentration ratio of PANI:PVA produced the highest selectivity of 564 compared to a value of 77 observed for the plain PVA membrane. Flux of the nanocomposite membranes was lower than those observed for the plain PVA membrane, but selectivity improved considerably. Membranes were characterized by differential scanning calorimetry, dynamic mechanical thermal analyzer, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and scanning electron microscopy. The highest selectivity with the lowest flux was observed for 10 mass% water containing feed mixture. Flux increased with increasing amount of water in the feed, but selectivity decreased considerably. These results were attributed to the acid-doped PANI particles in the PVA membrane as a result of change in the micromorphology of the nanocomposite membranes. In addition, molar mass between cross-links and fractional free volume of the membranes are responsible for the varying membrane performance. Temperature effect on permeability was investigated for 10 mass% water containing feed with the membrane containing higher concentration of PANI particles, the presence of which could be responsible for varied effect of water permeation through the membrane. Membranes of this study could remove as much as 98% of water from the feed.     

Polymer-Based Superhydrophobic Coating Fabricated from Polyelectrolyte Multilayers of Poly(allylamine hydrochloride) and Poly(acrylic acid)

Superhydrophobic films mainly based on poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) polyelectrolyte multilayer have been deposited onto cleaned glass substrate by a layer-by-layer dip coating method. 3 bilayers of the PAH and PAA was directly coated onto the substrate as an underlying layer for subsequent coating. Desired surface roughness on the polyelectrolyte bilayers was created by etching the bilayers in hydrochloric acid solution so as to create the open pore having suitable size at the surface. Then, nanoparticles such as SiO₂ and TiO₂ of various sizes were deposited onto the etched polyelectrolyte bilayers. Finally, the surfaces were further modified with semifluorinated silane followed by cross-linking at 180 °C for 2 h to obtain desirable surface morphological features. The effect of etching time and addition of nanoparticles on surface morphology was investigated using an atomic force microscope (AFM). Wetting ability of the prepared film was determined by measuring water droplet contact angle using a goniometer. Adhesion between the superhydrophobic films and the substrate was evaluated by using a standard tape test method (D3359). The adhesion was improved by reducing the organic content in the films.     

壳聚糖／聚丙烯酸聚电解质复合物膜对水／有机液体系的渗透汽化性能

以壳聚糖和聚丙烯酸为原料制备了聚电解质复合物膜，并对其分离水／乙醇体系的渗透汽化特性和浓度，温度，化学组成等因素的影响进行了研究，发现后处理方法对复合物膜的分离性能影响很大。同时对其它水／有机液体系，该膜也具备优异的分离性能。     

Pervaporation separation of water + 1,4-dioxane and water + tetrahydrofuran mixtures using sodium alginate and its blend membranes with hydroxyethylcellulose—A comparative study

Sodium alginate and hydroxyethylcellulose blend membranes were prepared by solution casting, crosslinked with glutaraldehyde and urea–formaldehyde–sulfuric acid mixture. Crosslinking was confirmed by Fourier transform infrared spectroscopy, while the blend compatibility was studied by differential scanning calorimetry and scanning electron microscopy. Membranes were tested for pervaporation separation of feed mixtures ranging from 10 to 50 mass% water in water + 1,4-dioxane and water + tetrahydrofuran mixtures at 30 °C. For 10 mass% of the feed mixture, pervaporation experiments were also carried out at higher temperatures (40 and 50 °C). By increasing the temperature, a slight increase in flux with a considerable decrease in selectivity was observed for all the membranes and for both the mixtures. The blend membranes exhibited different pervaporation performance for both the binary mixtures investigated. For water + 1,4-dioxane mixture, the pervaporation performance did not improve much after blending, whereas for water + tetrahydrofuran mixture, the pervaporation performance has improved considerably over that of plain sodium alginate membrane.     

Self-assembled polyelectrolyte multilayer membranes with highly improved pervaporation separation of ethanol/water mixtures

Ethanol/water pervaporation through ultrathin polyelectrolyte multilayer membranes is described. The membranes were prepared by the layer-by-layer technique, i.e. by alternating sequential adsorption of cationic and anionic polyelectrolytes on a porous support. The separation capability was optimized by variation of the chemical structure of the polyelectrolytes, by variation of pH and ionic strength of the polyelectrolyte solutions used for membrane preparation and by annealing of the polyelectrolyte membranes. It was found that the separation is mainly affected by the charge density of the polyelectrolytes which is controlled by the chemical structure and the degree of ionisation of the polar groups. Selectivity for water was highest, if polyelectrolytes of high charge density such as polyethyleneimine (PEI), polyvinylamine (PVA) and polyvinylsulfate (PVS) were used and if the pH of the polyelectrolyte solutions was equal to the mean of the pK_a values of the corresponding cationic and anionic polyelectrolyte. Best results were obtained for PVA/PVS and PEI/PVS membranes which are characterized in detail with regard to their separation behavior.     

Surface modification of poly(tetramethylene adipate-co-terephthalate) membrane via layer-by-layer assembly of chitosan and dextran sulfate polyelectrolyte multiplayer

The improvement of hydrophilicity and hemocompatibility of poly(tetramethylene adipate-co-terephthalate) (PTAT) membrane was developed via polyelectrolyte multilayers (PEMs) immobilization. The polysaccharide PEMs included chitosan (CS, as a positive-charged and antibacterial agent) and dextran sulfate (DS, as a negative-charged and anti-adhesive agent) were successfully prepared using the aminolyzed PTAT membrane in a layer-by-layer (LBL) self-assembly manner. The obtained results showed that the contact angle of as-modified PTAT membranes reached to the steady value after four bilayers of coating, hence suggesting that the full coverage was achieved. It could be found that the PTAT–PEMs membranes with DS as the outmost layer could resist the platelet adhesion and human plasma fibrinogen (HPF) adsorption, thereby prolonging effectively the blood coagulation times. According to L929 fibroblast cell growth inhibition index, the as-prepared PTAT membranes exhibited non-cytotoxic. Overall results demonstrated that such an easy, valid and shape-independent processing should be potential for surface modification of PTAT membrane in the application of hemodialysis devices.     

Electric field-enhanced assembly of polyelectrolyte composite membranes

In this paper, a novel method was developed to enhance the assembly of polyelectrolyte composite membranes by inducing an electric field during electrostatic adsorption process. The hydrolyzed polyacrylonitrile (PAN) ultrafiltration (UF) membrane was placed in between a capacitor setup. The polyethyleneimine (PEI) was compulsorily assembled on the PAN support under the action of external electric force. Subsequently, the polyelectrolyte composite membranes were evaluated by pervaporation separation of water and alcohol mixture. The membrane obtained with only one PEI layer had a separation factor of 304 and a permeate flux of 512 g/m² h (75 °C) for pervaporation of 95 wt% ethanol–water mixture. An atomic force microscopy was also used to observe the microtopographical changes. The regularity of the membranes assembled by the new method was also improved in comparison with the membrane assembled by a dynamic layer-by-layer adsorption.     

Pervaporation of alcohol-toluene mixtures through polymer blend membranes of poly(acrylic acid) and poly(vinyl alcohol)

Homogeneous membranes were prepared by blending poly(acrylic acid) with poly(vinyl alcohol). These blend membranes were evaluated for the selective separation of alcohols from toluene by pervaporation. The flux and selectivity of the membranes were determined both as a function of the blend composition and of the feed mixture composition. The results showed that a polymer blending method could be very useful to develop new membranes with improved permselectivity. The pervaporation properties could be optimized by adjusting the blend composition. All the blend membranes tested showed a decrease in flux with increasing poly(vinyl alcohol) content for both methanol—toluene and ethanol—toluene liquid mixtures. The alcohols permeated preferentially through all tested blend membranes, and the selectivity values increased with increasing poly(vinyl alcohol) content. The pervaporation characteristics of the blend membranes were also strongly influenced by the feed mixture composition. The fluxes increased exponentially with increasing alcohol concentration in the feed mixtures, whereas the selectivities decreased for both liquid mixtures.     

Novel nanocomposite pervaporation membranes composed of poly(vinyl alcohol) and chitosan-wrapped carbon nanotube

Novel nanocomposite membranes (PVA–CNT(CS)) were prepared by incorporating chitosan-wrapped multiwalled carbon nanotube (MWNT) into poly(vinyl alcohol) (PVA). To further explore the intrinsic correlation between pervaporation performance and free volume characteristics, molecular dynamics simulation was first introduced to qualitatively analyze the contribution of carbon nanotube incorporation on improving free volume characteristics of the nanocomposite membranes. Secondly, the pervaporation performance of PVA–CNT(CS) nanocomposite membranes was investigated using permeation flux and separation factor as evaluating parameters. For benzene/cyclohexane (50/50, w/w) mixtures at 323 K, permeation flux and separation factor of pure PVA membrane are only 20.3 g/(m² h) and 9.6, respectively, while the corresponding values of PVA–CNT(CS) (CNT content: 1%) nanocomposite membrane are 65.9 g/(m² h) and 53.4. In order to explain the simultaneous increase of permeation flux and separation factor, as well as to check the calculation reliability of molecular dynamics simulation, positron annihilation lifetime spectroscopy (PALS) analysis was employed.     

多金属氧酸盐K17[Ce(P2Mo17O61)2]多层膜修饰电极的组装及其电化学行为

利用层接层自组装法(LbL), 制备出有序且稳定的多金属氧酸盐K17[Ce(P2Mo17O61)2]多层膜. 应用电化学, 紫外光谱和X射线光电子能谱等方法研究该化合物的电化学性质及其膜修饰电极的电化学性质.     

Pervaporation characteristics of cross-linked poly(dimethylsiloxane) membranes for removal of various volatile organic compounds from water

The permeation and separation characteristics of volatile organic compounds (VOCs), such as chloroform, benzene, and toluene, from water by pervaporation through cross-linked poly(dimethylsiloxane) membranes prepared from poly(dimethylsiloxane) dimethylmethacrylate macromonomer (PDMSDMMA) and divinyl compounds, such as ethylene glycol dimethylmethacrylate (EGDM), divinyl benzene (DVB), divinyl siloxane (DVS), and divinyl perfluoro-n-hexane (DVF) are described. When aqueous solutions containing 0.05 wt.% VOCs were permeated through cross-linked PDMSDMMA membranes, these membranes showed high VOC/water selectivity and permeability. Both VOC/water selectivity and permeability were affected significantly by the divinyl compound. Furthermore cross-linked PDMSDMMA membranes showed the highest chloroform/water selectivity. The VOC/water selectivity was mainly governed by the sorption selectivity rather than the diffusion selectivity. However, the difference in the selectivity between different types of VOCs depended on differences in the diffusivity of permeants. With increasing downstream pressure, the VOC/water selectivity of all cross-linked PDMSDMMA membranes increased, but the permeability decreased. A PDMSDMMA–DVF membrane exhibited a normalized permeation rate of 1.9 × 10⁻⁵ kg m/m² h and a separation factor for chloroform/water of 4850, yielding a separation index of 9110. The pervaporation characteristics of the cross-linked PDMSDMMA membranes are discussed based on their chemical and physical structures as well as the chemical and physical properties of the permeants.     

Poly (caprolactone)/poly (ethylene glycol) pervaporation blend membranes: Synthesis,characterization, and performance

Poly (caprolactone) membranes with addition of different poly (ethylene glycol) concentrations were prepared for separation of water/isopropanol azeotropic mixture by pervaporation process. Different characterization tests including Fourier transform infrared, scanning electron microscopy, water contact angle, and thermogravimetric analysis were carried out on the prepared membranes. In addition, the effect of poly (ethylene glycol) PEG content on the swelling degree and the performance of the prepared membranes in pervaporation process were investigated. According to the obtained results, all the membranes were water selective and the blend membrane containing 3 wt% PEG exhibited the best pervaporation performance with a water flux of 0.517 kg/m² hour and separation factor of 1642 at the ambient temperature. Hydrophilicity improvement of the blend membranes was confirmed by constant decrease in water contact angle of the membranes as PEG content increased in the casting solution. Scanning electron microscopy cross‐sectional images indicated that the blend membranes containing PEG had a closed cellular structure. Furthermore, mechanical and thermal properties of the membranes decreased by adding PEG.     

Ultrathin self-assembled polyelectrolyte membranes for pervaporation

Ethanol–water pervaporation through new composite membranes with ultrathin self-assembled polyelectrolyte separating layer is described. The composite membranes were prepared by alternating electrostatic adsorption of poly(allylamine hydrochloride) (PAH) and poly(styrene sulfonate sodium salt) (PSS) on a porous PAN/PET supporting membrane (a polyethylene terephthalate fleece coated with a thin layer of polyacrylonitrile). The sealing of the pores of the supporting membrane was studied by gas flow measurements. Pervaporation experiments were carried out under variation of the preparation and operation conditions. Generally it was found that the separation capability considerably increased, when the composite membrane was annealed at temperatures above 60°C, while the flux simultaneously decreased. The same was found, when the number of PAH/PSS layers was increased. Raising the pervaporation temperature led to both an increase of the flux and the separation factor. The highest separation factor of 70 was found at a low water content of the feed of 6.2% (w/w). The corresponding flux was 230 g m⁻² h⁻¹. Pervaporation was feasible up to a water content of 24% (w/w) in the feed. At higher values, hydrolysis set in resulting in partial desorption of the separating layer.     

Silver nanocomposite layer-by-layer films based on assembled polyelectrolyte/dendrimer

Silver nanocomposite multilayer films were prepared through the in situ method. Multilayer thin films, prepared through the sequential electrostatic deposition of a positively charged third-generation poly(amidoamine) dendrimer (PAMAM) and negatively charged poly(styrenesulfonate) (PSS) and poly(acrylic acid) (PAA), were utilized as nanoreactors for the formation of silver nanoparticles. The silver ions were preorganized in layer-by-layer (LBL) films composed of PAMAM dendrimers and subsequently reduced with hydrogen to prepare the silver nanoparticles. The UV-vis spectrum and profilometer were used to characterize the regular growth of bilayers. UV-vis absorption from plasmon resonance at 435 nm and TEM images indicated the formation of the silver nanoparticles in the multilayer films. The silver nanocomposite LBL films were also constructed on the indium tin oxide-glass and investigated using cyclic voltammetry. The silver nanoparticles in the multilayer films have a stronger negative redox potential. The silver nanocomposite LBL films may have a potential application in the catalysis of reduction of 4-nitrophenol with sodium borohydride.     

Poly(vinyl alcohol)/poly(methyl methacrylate) blend membranes for pervaporation separation of water + isopropanol and water + 1,4-dioxane mixtures

Pervaporation (PV) separation of water + isopropanol and water + 1,4-dioxane mixtures has been attempted using the blend membranes of poly(vinyl alcohol) (PVA) with 5 wt.% of poly(methyl methacrylate) (PMMA). These results have been compared with the plain PVA membrane. Both plain PVA and PVA/PMMA blend membranes have been crosslinked with glutaraldehyde in an acidic medium. The membranes were characterized by differential scanning calorimetry and universal testing machine. Pervaporation separation experiments have been performed at 30 °C for 10, 15, 20, 30 and 40 wt.% of feed water mixtures containing isopropanol as well as 1,4-dioxane. PVA/PMMA blend membrane has shown a selectivity of 400 for 10 wt.% of water in water + isopropanol feed, while for water + 1,4-dioxane feed mixture, membrane selectivity to water was 104 at 30 °C. For both the feed mixtures, selectivity for the blend membrane was higher than that observed for plain PVA membrane, but flux of the blend membrane was lower than that observed for the plain PVA membrane. Membranes of this study are able to remove as much as 98 wt.% of water from the feed mixtures of water + isopropanol, while 92 wt.% of water was removed from water + 1,4-dioxane feed mixtures at 30 °C. Flux of water increased for both the feed mixtures, while the selectivity decreased at higher feed water concentrations. The same trends were observed at 40 and 50 °C for 10, 15 and 20 wt.% of water mixtures containing isopropanol as well as 1,4-dioxane feed mixtures, which also covered their azeotropic composition ranges. Membrane performance was studied by calculating flux (J_p), selectivity (), pervaporation separation index (PSI) and enrichment factor (β). Permeation flux followed the Arrhenius trend over the range of temperatures investigated. It was found that by introducing a hydrophobic PMMA polymer into a hydrophilic PVA, the selectivity increased dramatically, while flux decreased compared to plain PVA, due to a loss in PVA chain relaxation.     

Use of polyelectrolyte multilayer systems for membrane modification

Membranes with designed surface and filtration properties were prepared by the adsorption of polyelectrolyte multilayer systems on membrane surfaces using the layer-by-layer electrostatic self assembly (ESA) technique. Microfiltration membranes with a first polyelectrolyte layer grafted onto the surface showed excellent stability during filtration process. Although a twofold higher permeate flux was observed for a three-layer polyelectrolyte complex membrane compared to a just grafted one the protein retention did not change remarkably. Additionally, a reduced protein adsorption was detected for repulsive electrostatic forces between the substrate and the protein under applied conditions. Pervaporation membranes with an anionically functionalized polyamide-6 support or Nafion^®-117 support and a dense separating layer consisting of poly(acrylic acid) and poly(ethylenimine) were prepared. Those membranes were used to separate aqueous organic mixtures. Six double layers were sufficient to obtain membranes with high water permselectivity. Membranes with similar properties but a lower number of deposited layers were obtained, when the adsorption process was carried out at 80°C.