Electronic properties of the metal/organic interlayer/inorganic semiconductor sandwich device

In this study, we prepared a Metal(Al)/Organic Interlayer(Congo Red=CR)/Inorganic Semiconductor (p-Si) (MIS) Schottky device formed by coating of an organic film on p-Si semiconductor wafer. The Al/CR/p-Si MIS device had a good rectifying behavior. By using the forward bias I-V characteristics, the values of ideality factor (n) and barrier height (Φ_b) for the Al/CR/p-Si MIS device were obtained as 1.68 and 0.77 eV, respectively. It was seen that the Φ_b value of 0.77 eV calculated for the Al/CR/p-Si MIS device was significantly higher than value of 0.50 eV of the conventional Al/p-Si Schottky diodes. Modification of the interfacial potential barrier of the Al/p-Si diode was achieved by using a thin interlayer of the CR organic material. This was attributed to the fact that the CR organic interlayer increased the effective barrier height by influencing the space charge region of Si. The interface-state density of the MIS diode was found to vary from 1.24×10¹³ to 2.44×10¹² eV⁻¹ cm⁻².     

Influence of surface cleaning effects on properties of Schottky diodes on 4H-SiC

Ir/4H-SiC and IrO₂/4H-SiC Schottky diodes are reported in terms of different methods of surface pretreatment before contact deposition. In order to find the effect of surface preparation processes on Schottky characteristics the SiC wafers were respectively cleaned using the following processes: (1) RCA method followed by buffered HF dip. Next, the surface was oxidized (5.5 nm oxide) using a rapid thermal processing reactor chamber and circular geometry windows were opened in the oxide layer before metallization deposition; (2) the same as sequence (1) but with an additional in situ sputter etching step before metallization deposition; (3) cleaning in organic solvents followed by buffered HF dip. The I-V characteristics of Schottky diodes were analyzed to find a correlation between extracted parameters and surface treatment. The best results were obtained for the sequence (1) taking into account theoretical value of Schottky barrier height. The contacts showed excellent Schottky behavior with ideality factors below 1.08 and barrier heights of 1.46 eV and 1.64 eV for Ir and IrO₂, respectively. Very promising results were obtained for samples prepared using the sequence (2) taking into account the total static power losses because the modified surface preparation results in a decrease in the forward voltage drop and reverse leakage current simultaneously. The contacts with ideality factor below 1.09 and barrier height of 1.02 eV were fabricated for Ir/4H-SiC diodes in sequence (2).     

Investigation of electrical and ammonia sensing characteristics of Schottky barrier diode based on a single ultra-long ZnO nanorod

Novel ultra-long ZnO nanorods, with lengths about 0.5-1.5 mm and diameters ranging from 100 to 1000 nm, in mass production have been synthesized via the vapor-phase transport method with CuO catalyst at 900 °C. Rectifying Schottky barrier diodes have been fabricated by aligning a single ultra-long ZnO nanorod across paired Ag electrodes. The resulting current-voltage (I-V) characteristics of the SBD exhibit a clear rectifying behavior. The ideality factor of the diode is about 4.6, and the threshold voltage is about 0.54 V at room temperature (300 K). At the same time the detailed I-V characteristics have been investigated in the temperature range 423-523 K. In addition, after exposure of the Schottky diodes to NH₃, the forward and reverse currents increase rapidly, indicating a high sensitivity to NH₃ gas.     

The effect of interface states, excess capacitance and series resistance in the Al/SiO2/p-Si Schottky diodes

The current-voltage (I-V) characteristics of Al/SiO₂/p-Si metal-insulator-semiconductor (MIS) Schottky diodes were measured at room temperature. In addition the capacitance-voltage (C-V) and conductance-voltage (G-V) measurements are studied at frequency range of 10 kHz-1 MHz. The higher value of ideality factor of 3.25 was attributed to the presence of an interfacial insulator layer between metal and semiconductor and the high density of interface states localized at Si/SiO₂ interface. The density of interface states (N_ss) distribution profile as a function of (E_ss − E_v) was extracted from the forward bias I-V measurements by taking into account the bias dependence of the effective barrier height (Φ_e) at room temperature for the Schottky diode on the order of ≅4 × 10¹³ eV⁻¹ cm⁻²_. These high values of N_ss were responsible for the non-ideal behaviour of I-V and C-V characteristics. Frequency dispersion in C-V and G-V can be interpreted only in terms of interface states. The N_ss can follow the ac signal especially at low frequencies and yield an excess capacitance. Experimental results show that the I-V, C-V and G-V characteristics of SD are affected not only in N_ss but also in series resistance (R_s), and the location of N_ss and R_s has a significant on electrical characteristics of Schottky diodes.     

Annealing and measurement temperature dependence of W2B5-based rectifying contacts to n-GaN

The thermal stability and measurement temperature dependence of Schottky contact characteristics on n-GaN using a W₂B₅/Ti/Au metallization scheme was studied using current-voltage (I-V), scanning electron microscopy (SEM) and Auger electron spectroscopy (AES) measurements. The elemental profile obtained from samples annealed at 350 °C showed some titanium diffusion into the gold layer but little other difference from the as-deposited wafer. Annealing at 700 °C produced significant diffusion of titanium. The Schottky barrier height increased with anneal temperature up to 200 °C, reaching a maximum value of 0.65 eV, but decreased at higher annealing temperatures. The reverse breakdown voltage from diodes fabricated using the W₂B₅-based contacts showed a similar dependence. The reverse current magnitude was larger than predicted by thermionic emission alone. The barrier height showed only minor changes with measurement temperature up to 150 °C.     

The barrier height inhomogeneity in Al/p-Si Schottky barrier diodes with native insulator layer

The current-voltage (I-V) characteristics of Al/p-Si Schottky barrier diodes (SBDs) with native insulator layer were measured in the temperature range of 150-375 K. The estimated zero-bias barrier height Φ_B0 and the ideality factor n assuming thermionic emission (TE) theory show strong temperature dependence. Evaluation of the forward I-V data reveals an increase of zero-bias barrier height Φ_B0 but decrease of ideality factor n with increase in temperature. The conventional Richardson plot exhibits non-linearity below 250 K with the linear portion corresponding to activation energy of 0.41 eV and Richardson constant (A^*) value of 1.3 × 10⁻⁴ A cm⁻² K⁻² is determined from intercept at the ordinate of this experimental plot, which is much lower than the known value of 32 A cm² K² for holes in p-type Si. Such behavior is attributed to Schottky barrier inhomogene ties by assuming a Gaussian distribution of barrier heights (BHs) due to barrier height inhomogeneities that prevail at interface. Also, Φ_B0 versus q/2kT plot was drawn to obtain evidence of a Gaussian distribution of the BHs, and values of Φ_B0 = 1.055 eV and σ₀ = 0.13 V for the mean BH and zero-bias standard deviation have been obtained from this plot, respectively. Thus, the modified versus q/kT plot gives Φ_B0 and A^* as 1.050 eV and 40.08 A cm⁻² K⁻², respectively, without using the temperature coefficient of the barrier height. This value of the Richardson constant 40.03 A cm⁻² K⁻² is very close to the theoretical value of 32 A K⁻² cm⁻² for p-type Si. Hence, it has been concluded that the temperature dependence of the forward I-V characteristics of the Al/p-Si Schottky barrier diodes with native insulator layer can be successfully explained on the basis of TE mechanism with a Gaussian distribution of the barrier heights.     

Applications of vertically oriented TiO2 micro-pillars array on the electrode of dye-sensitized solar cell

In this research, dye-sensitized solar cells based on TiO₂ micro-pillars fabricated by inductive couple plasma etcher were investigated by analyses of X-ray diffraction (XRD), scanning electron microscopy (SEM), contact angle, ultraviolet-visible absorption spectra (UV-vis), and current-voltage characteristics. X-ray diffraction patterns show that the TiO₂ anatase phase forms while sintering at 450 °C for 30 min. The SEM images reveal that the diameter and height of TiO₂ micro-pillars are about 3 and 0.8 μm, respectively. The measurements of contact angle between TiO₂ micro-pillars and deionized water (DI water) reveal that the TiO₂ micro-pillars is super-hydrophilic while annealed at 450 °C for 30 min.The absorption spectrum of TiO₂ micro-pillars is better than TiO₂ thin film and can be widely improved in visible region with N3 dye adsorbed. The results of current-voltage (I-V) characteristics analysis reveal that dye-sensitized solar cell with TiO₂ micro-pillars electrode has better I-V characteristics and efficiency than TiO₂ film electrodes. This result may be due to the annealed TiO₂ micro-pillars applied on the electrode of dye-sensitized solar cell can increase the contact area between TiO₂ and dye, resulting in the enhancement of I-V characteristics and efficiency for dye-sensitized solar cell.     

Comparison of electrical parameters of Zn/p-Si and Sn/p-Si Schottky barrier diodes

In this study, current-voltage (I-V) and capacitance-voltage (C-V) characteristics of metal-semiconductor (MS) Zn/p-Si and Sn/p-Si Schottky diodes, with high resistivity silicon structures, are investigated. The parameters of series resistance (R_S), the ideality factor (n) and the barrier height (Φ_b) are determined by performing different plots from the forward bias current-voltage (I-V) and reverse bias capacitance-voltage (C-V) characteristics. Thus, the barrier heights (Φ_b) for the Si Schottky diodes obtained between 0.725 and 1.051 eV, the ideality factor (n) between 1.043 and 1.309, and the series resistance (R_S) between 12.594 and 12.950 kΩ. The energy distribution of interface states density was determined from the forward bias I-V characteristics by taking into account the bias dependence of the effective barrier height. It was concluded that the density of interface states in the considered energy range are in close agreement with each other values obtained for Zn/p-Si and Sn/p-Si Schottky diodes.     

Preparation of Cu2ZnSnS4 thin films by hybrid sputtering

In order to fabricate Cu₂ZnSnS₄ thin films, hybrid sputtering system with two sputter sources and two effusion cells is used. The Cu₂ZnSnS₄ films are fabricated by the sequential deposition of metal elements and annealing in S flux, varying the substrate temperature. The Cu₂ZnSnS₄ films with stoichiometric composition are obtained at the substrate temperature up to 400 °C, whereas the film composition becomes quite Zn-pool at the substrate temperature above 450 °C. The Cu₂ZnSnS₄ film shows p-type conductivity, and the optical absorption coefficient and the band gap of the Cu₂ZnSnS₄ film prepared in this experiment are suitable for fabricating a thin film solar cell.     

Current transport mechanism in Al/Si3N4/p-Si (MIS) Schottky barrier diodes at low temperatures

The current-voltage (I-V) and capacitance-voltage (C-V) characteristics of metal-insulator-semiconductor (Al/Si₃N₄/p-Si) Schottky barrier diodes (SBDs) were measured in the temperature range of 80-300 K. By using the thermionic emission (TE) theory, the zero-bias barrier height Φ_B0 calculated from I-V characteristics was found to increase with increasing temperature. Such temperature dependence is an obvious disagreement with the negative temperature coefficient of the barrier height calculated from C-V characteristics. Also, the ideality factor decreases with increasing temperature, and especially the activation energy plot is nonlinear at low temperatures. Such behaviour is attributed to Schottky barrier inhomogeneties by assuming a Gaussian distribution of barrier heights (BHs) at interface. We attempted to draw a Φ_B0 versus q/2kT plot to obtain evidence of a Gaussian distribution of the BHs, and the values of Φ_Bo = 0.826 eV and α_o = 0.091 V for the mean barrier height and standard deviation at zero-bias, respectively, have been obtained from this plot. Thus, a modified ln(I_o/T²) − q²σ_o²/2(kT)² versus q/kT plot gives Φ_B0 and Richardson constant A^* as 0.820 eV and 30.273 A/cm² K², respectively, without using the temperature coefficient of the barrier height. This value of the Richardson constant 30.273 A/cm² K² is very close to the theoretical value of 32 A/cm² K² for p-type Si. Hence, it has been concluded that the temperature dependence of the forward I-V characteristics of the Al/Si₃N₄/p-Si Schottky barrier diodes can be successfully explained on the basis of TE mechanism with a Gaussian distribution of the barrier heights. In addition, the temperature dependence of energy distribution of interface state density (N_SS) profiles was determined from the forward I-V measurements by taking into account the bias dependence of the effective barrier height and ideality factor.     

Current-voltage characteristics of Au/GaN/GaAs structure

Au/GaN/n-GaAs structure has been fabricated by the electrochemically anodic nitridation method for providing an evidence of achievement of stable electronic passivation of n-doped GaAs surface. The change of the electronic properties of the GaAs surface induced by the nitridation process has been studied by means of current-voltage (I-V) characterizations on Schottky barrier diodes (SBDs) shaped on gallium nitride/gallium arsenide structure. Au/GaN/n-GaAs Schottky diode that showed rectifying behavior with an ideality factor value of 2.06 and barrier height value of 0.73 eV obeys a metal-interfacial layer-semiconductor (MIS) configuration rather than an ideal Schottky diode due to the existence of GaN at the Au/GaAs interfacial layer. The formation of the GaN interfacial layer for the stable passivation of gallium arsenide surface is investigated through calculation of the interface state density N_ss with and without taking into account the series resistance R_s. While the interface state density calculated without taking into account R_s has increased exponentially with bias from 2.2×10¹² cm⁻² eV⁻¹ in (E_c−0.48) eV to 3.85×10¹² cm⁻² eV⁻¹ in (E_c−0.32) eV of n-GaAs, the N_ss obtained taking into account the series resistance has remained constant with a value of 2.2×10¹² cm⁻² eV⁻¹ in the same interval. This has been attributed to the passivation of the n-doped GaAs surface with the formation of the GaN interfacial layer.     

Cathodic and anodic pre-treated boron doped diamond with different sp content: Morphological,structural, and impedance spectroscopy characterizations

In this work, the influence of cathodic (Red) and anodic (Ox) pre-treatment on boron doped diamond (BDD) films grown with different sp²/sp³ ratios was systematically studied. The sp²/sp³ ratios were controlled by the addition of CH₄ of 1,3,5 and 7 sccm in the gas inlet during the growth process. The electrodes were treated in 0.5 mol L⁻¹ H₂SO₄ at −3 and 3 V vs Ag/AgCl, respectively, for 30 min. The electrochemical response of BDD films was investigated using electrochemical impedance spectroscopy (EIS) and Mott–Schottky Plot (MSP) measurements. Four film sample sets were produced in a hot filament chemical vapor deposition reactor. During the growth process, an additional H₂ line passing through a bubbler containing the B₂O₃ dissolved in methanol was used to carry the boron. The scanning electron microscopy morphology showed well faced films with a small decrease in their grain size as the CH₄ concentration increased. The Raman spectra depicted a pronounced sp² band, mainly for films with 5 and 7 sccm of CH₄. MSP showed a decrease in the acceptor concentration as the CH₄ increased indicating the CH₄ influence on the doping process for Red–BDD and Ox–BDD samples. Nonetheless, an apparent increase in the acceptor concentrations for both Ox–BDD samples was observed compared to that for Red–BDD samples, mainly attributed to the surface conductive layer (SCL) formation after this strong oxidation process. The EIS Nyquist plots for Red–BDD showed a capacitance increase for the films with higher sp² content (5 and 7 sccm). On the other hand, the Nyquist plots for Ox–BDD can be described as semicircles near the origin, at high frequencies, where their charge transfer resistance strongly varied with the sp² increase in such films.     

Chemical diffusion in molybdenum disulphide

Ceramic molybdenum disulphide (MoS₂) was equilibrated at an ambient sulphur vapour partial pressure p(S₂), 10 Pa<p(S₂)<1000 Pa. After the step change of p(S₂) to a new value, the equilibration kinetics was monitored by measuring electrical conductivity. The application of the solution of Fick's second law (with the initial condition: no concentration gradient in specimen and the boundary condition: surface concentration constant) to the kinetic data gave the chemical diffusion coefficient. The chemical diffusion coefficient, D_chem, determined at 1273 K, was D_chem=(3.20±0.32)*10⁻⁷ cm² s⁻¹ and was found to be independent of sulphur vapour partial pressure. The usefulness of transient electrical conductivity method for determining real values of diffusion data was discussed in terms of defect structure of the studied material.     

Temperature-dependent optical absorption measurements and Schottky contact behavior in layered semiconductor n-type InSe(:Sn)

The layered n-InSe(:Sn) single crystal samples have been cleaved from a large crystal ingot grown from non-stoichiometric melt by the Bridgman-Stockbarger method. It has been made the absorption measurements of these samples without Schottky contact under electric fields of 0.0 and 6000 V cm⁻¹. The band gap energy value of the InSe:Sn has been calculated as 1.36 ± 0.01 eV (at 10 K) and 1.28 ± 0.01 eV (at 300 K) under zero electrical field, and 1.31 ± 0.01 eV (at 10 K) and 1.26 ± 0.01 eV (at 300 K) under 6000 Vcm⁻¹. The current-voltage (I-V) characteristics of Au-Ge/InSe(:Sn)/In Schottky diodes have been measured in the temperature range 80-320 K with a temperature step of 20 K. An experimental barrier height (BH) Φ_ap value of about 0.70 ± 0.01 eV was obtained for the Au-Ge/InSe(:Sn)/In Schottky diode at the room temperature (300 K). An abnormal decrease in the experimental BH Φ_b and an increase in the ideality factor n with a decrease in temperature have been explained by the barrier inhomogeneities at the metal-semiconductor interface. From the temperature-dependent I-V characteristics of the Au-Ge/InSe(:Sn)/In contact, that is, and A^* as 0.94 ± 0.02 and 0.58 ± 0.02 eV, and 27 ± 2 and 21 ± 1 (A/cm² K²), respectively, have been calculated from a modified versus 1/T plot for the two temperature regions. The Richardson constant values are about two times larger than the known value of 14.4 (A/cm² K²) known for n-type InSe. Moreover, in the temperature range 80-320 K, we have also discussed whether or not the current through the junction has been connected with TFE.     

Specific heat measurements in pure and in (Cu, Mn, Fe, Ni)-doped single-crystals of l-arginine phosphate monohydrate

The influence of highly diluted impurities (Cu, Mn, Fe, Ni) on the temperature (T) dependence of the specific heat (c_p) of l-arginine phosphate monohydrate (LAP) was investigated in the temperature range 1.8-300 K. The doped samples yielded values for c_p in excess to those obtained for a pure LAP sample. The melting temperatures (T_m≈420 K) obtained by differential scanning calorimetry for pure and doped LAP samples were found not to be significantly affected by the impurities. The T-dependence of c_p was fully accounted for by taking into consideration the Debye contribution, an Einstein term and a contribution due to both Frenkel and Schottky defects. The model fit all c_p versus T data using a single value for both the Debye (θ_D=160 K) and the Einstein (T_E=376.8 K) temperatures, and for the energy (ε_d=157.9 meV) required to create the defects.     

Electrical properties and Schottky diodes using N-N′diphenyl-1-4phenylenediamine

Thin films of, N-N′diphenyl 1-4phenylene-diamineane are prepared using vacuum sublimation technique. The electrical conductivity from room temperature down to 127 K is studied. It is found that the conduction of charge carriers obeys T^−1/2 dependence on temperature. The average hopping distance, hopping energy, density of states and their variation due to post-deposition heat treatment are studied. Schottky diodes are fabricated with gold as ohmic contact and aluminium as Schottky contact. From the observed current voltage characteristics the saturation current density, diode ideality factor and the barrier height are determined. Their variation with air annealing is also investigated.     

High temperature characteristics of ZnO-based MOS-FETs with a photochemical vapor deposition SiO2 gate dielectric

The authors report the fabrication of ZnO-based metal-oxide-semiconductor field effect transistors (MOSFETs) with a high quality SiO₂ gate dielectric by photochemical vapor deposition (photo-CVD) on a sapphire substrate. Compared with ZnO-based metal-semiconductor FETs (MESFETs), it was found that the gate leakage current was decreased to more than two orders of magnitude by inserting the photo-CVD SiO₂ gate dielectric between ZnO and gate metal. Besides, it was also found that the fabricated ZnO MOSFETs can achieve normal operation of FET, even operated at 150 °C. This could be attributed to the high quality of photo-CVD SiO₂ layer. With a 2 μm gate length, the saturated I_ds and maximum transconductance (G_m) were 61.1 mA/mm and 10.2 mS/mm for ZnO-based MOSFETs measured at room temperature, while 45.7 mA/mm and 7.67 mS/mm for that measured at 150 °C, respectively.     

Electrical and structural properties of a stacked metal layer contact to n-InP

In this study, we found that the double metal contact structure in Pt/Al/n-InP diodes provides better rectification characteristics than conventional single-metal/n-InP Schottky diodes. The effective barrier height was measured to be 0.67 eV for a 400 °C-annealed Pt/Al/n-InP diode sample. The increase in the barrier height is attributed to the formation of Al₂O₃ at the metal/n-InP contact interface during thermal annealing. The formation of the phase Al₂O₃ phase was monitored by X-ray diffraction (XRD) analysis. The corresponding element profiles of Al and O were also confirmed at the metal/n-InP contact interface using secondary ion mass spectrum (SIMS) analysis. The lowering of the Schottky barrier height due to the inhomogeneity at the metal/n-InP junction is also discussed on the basis of the TE theory. The distribution of local effective Schottky barrier heights was explained by a model incorporating the existence of double Gaussian barrier heights, which represent the high barrier and low barrier of the full distribution in the temperature ranges of 83-198 and 198-300 K.     

Molecular control over Ag/p-Si diode by organic layer

Electrical transport properties of Ag metal-fluorescein sodium salt (FSS) organic layer-silicon junction have been investigated. The current-voltage (I-V) characteristics of the diode show rectifying behavior consistent with a potential barrier formed at the interface. The diode indicates a non-ideal I-V behavior with an ideality factor higher than unity. The ideality factor of the Ag/FSS/p-Si diode decreases with increasing temperature and the barrier height increases with increasing temperature. The barrier height (φ_b=0.98 eV) obtained from the capacitance-voltage (C-V) curve is higher than barrier height (φ_b=0.72 eV) derived from the I-V measurements. The barrier height of the Ag/FSS/p-Si Schottky diode at the room temperature is significantly larger than that of the Ag/p-Si Schottky diode. It is evaluated that the FSS organic layer controls electrical charge transport properties of Ag/p-Si diode by excluding effects of the SiO₂ residual oxides on the hybrid diode.     

Interface properties of an O2 annealed Au/Ni/n-Al0.18Ga0.82N Schottky contact

We oxidized a Ni/Au metal bi-layer contact fabricated on HVPE Al_0.18Ga_0.82N from 373 K to 573 K in 100 K steps. In the range 1 kHz to 2 MHz, the Capacitance–Voltage–Frequency (C–V–f) measurements reveal a frequency dispersion of the capacitance and the presence of an anomalous peak at 0.4 V owing to the presence of interface states in the as deposited contact system. The dispersion was progressively removed by O₂ anneals from temperatures as low as 373 K. These changes are accompanied by an improvement in the overall quality of the Schottky system: the ideality factor, n, improves from 2.09 to 1.26; the Schottky barrier height (SBH), determined by the Norde [1] method, increases from 0.72 eV to 1.54 eV. From the Nicollian and Goetzberger model [2], we calculated the energy distribution of the density of interface states, N_SS. Around 1 eV above the Al_0.18Ga_0.82N valence band, N_SS, decreases from 2.3×10¹² eV⁻¹ cm⁻² for the un-annealed diodes to 1.3×10¹² eV⁻¹ cm⁻² after the 573 K anneal. Our results suggest the formation of an insulating NiO leading to a MIS structure for the oxidized Au/Ni/Al_0.18Ga_0.82N contact.