Effect of Al2O3 on the electrical properties of ZnO-Pr6O11-based varistor ceramics

The effect of Al₂O₃ on the electrical properties of ZnO-Pr₆O₁₁-based ceramics is investigated in this work. The average grain size of ZnO increased as the Al₂O₃ content increased from 10.3 to 13.5 μm. It was found that a sample doped with Al₂O₃ of 0.005 mol% showed the highest nonlinear current-voltage characteristics with a nonlinear exponent of 43.8 and a leakage current of 0.66 μA. When the Al₂O₃ content was increased, the donor concentration was increased from 0.51×10¹⁸/cm³ to 1.59×10¹⁸/cm³, but the barrier height was decreased from 1.01 to 0.87 eV. The best electrical stability against aging stress was obtained by doping Al₂O₃ of 0.001 mol%.     

Dielectric dispersion in PbO-Sb2O3-As2O3:V2O5 glasses

Dielectric properties, viz. dielectric constant ε′, loss tan δ and a.c conductivity σ_ac (over a wide range of frequency and temperature) and dielectric breakdown strength of PbO-Sb₂O₃-As₂O₃ glasses doped with V₂O₅ (ranging from 0 to 0.5 mol%) are studied. Analysis of these results, based on optical absorption and ESR spectra, indicates that the insulating strength of the glasses is comparatively high when the concentration of V₂O₅ is about 0.3 mol% in the glass matrix.     

Characteristics of sandwich-structured Al2O3/HfO2/Al2O3 gate dielectric films on ultra-thin silicon-on-insulator substrates

Sandwich-structure Al₂O₃/HfO₂/Al₂O₃ gate dielectric films were grown on ultra-thin silicon-on-insulator (SOI) substrates by vacuum electron beam evaporation (EB-PVD) method. AFM and TEM observations showed that the films remained amorphous even after post-annealing treatment at 950 °C with smooth surface and clean silicon interface. EDX- and XPS-analysis results revealed no silicate or silicide at the silicon interface. The equivalent oxide thickness was 3 nm and the dielectric constant was around 7.2, as determined by electrical measurements. A fixed charge density of 3 × 10¹⁰ cm⁻² and a leakage current of 5 × 10⁻⁷A/cm² at 2 V gate bias were achieved for Au/gate stack /Si/SiO₂/Si/Au MIS capacitors. Post-annealing treatment was found to effectively reduce trap density, but increase in annealing temperature did not made any significant difference in the electrical performance.     

Electrical conduction and magnetoelectric effect of (x) BaTiO3 + (1−x) Ni0.92Co0.03Cu0.05Fe2O4 composites in ferroelectric rich region

Particulate composites with composition (x)BaTiO₃+(1−x)Ni_0.92Co_0.03Cu_0.05Fe₂O₄ in which x varies as 1, 0.85, 0.70, 0.55 and 0 (in mol%) were prepared by the conventional double sintering ceramic technique. The presence of two phases viz. ferromagnetic (Ni_0.92Co_0.03Cu_0.05Fe₂O₄) and ferroelectric (BaTiO₃) was confirmed by X-ray diffraction analysis. The dc resistivity and thermo-emf measurements were carried out with variation of temperature. The ac conductivity (σ_ac) measurements investigated in the frequency range 100 Hz to 1 MHz conclude that the conduction in these composites is due to small polarons. The variation of dielectric constant and loss tangent with frequency (20 Hz to 1 MHz) was studied. The static magnetoelectric conversion factor, i.e. dc (dE/dH)_H was measured as a function of intensity of applied magnetic field. The changes were observed in electrical properties as well as in magnetoelectric voltage coefficient as the molar ratio of the constituent phases was varied. A maximum value of magnetoelectric conversion factor of 536.06 μV/cm Oe was observed for the composite with 70% BaTiO₃+30% Ni_0.92Co_0.03Cu_0.05Fe₂O₄ at a dc magnetic field of 2.3 K Oe. The maximum magnetoelectric conversion output has been explained in terms of ferrite-ferroelectric content, applied static magnetic field and resistivity.     

Nickel ion—A structural probe in BaO-Al2O3-P2O5 glass system by means of dielectric, spectroscopic and magnetic studies

BaO-Al₂O₃-P₂O₅ glasses containing different concentrations of NiO (ranging from 0 to 1.0 mol%) were prepared. A number of studies viz., chemical durability, differential thermal analysis, spectroscopic (infrared, optical absorption spectra), magnetic susceptibility and dielectric properties (constant ε′, loss tan δ, AC conductivity σ_AC over a range of frequency and temperature) of these glasses have been carried out. The studies on chemical durability indicate that there is a significant increase in the corrosion resistance of the glasses; where as the results of differential thermal analysis suggests that there is a substantial improvement in the glass forming ability, with increase in the concentration of NiO up to 0.6 mol% in the glass matrix. The optical absorption, magnetic susceptibility and IR spectral studies point out nickel ions occupy both tetrahedral and octahedral positions in the glass network; the later positions seems to be dominant when the concentration of NiO is beyond 0.6 mol% in the glass matrix. The studies of dielectric properties reveal that the presence of nickel oxide in the glass network causes a considerable improvement in the insulating strength of the se glasses when the concentration of NiO?0.6 mol%.     

The role of iron ions on the structure and certain physical properties of PbO-As2O3 glasses

Various studies have been carried out viz optical absorption, infrared spectra, magnetic susceptibility, dielectric parameters (dielectric constant, loss and a.c. conductivity over a range of frequency and temperature; and breakdown strength) and differential thermal analysis of PbO-As₂O₃ glasses containing 0-1 mol% of Fe₂O₃. An anomaly has been observed in all the properties of these glasses when Fe₂O₃ concentration is about 0.25 mol%. The reasons for such anomaly have been identified and found that PbO-As₂O₃ glasses are more stable when Fe₂O₃ concentration is about 0.25 mol%.     

Synthesis and electrochemical performances of Li4Ti4.95Al0.05O12/C as anode material for lithium-ion batteries

Spinel compounds Li₄Ti_5−xAl_xO₁₂/C (x=0, 0.05) were synthesized via solid state reaction in an Ar atmosphere, and the electrochemical properties were investigated by means of electronic conductivity, cyclic voltammetry, and charge-discharge tests at different discharge voltage ranges (0-2.5 V and 1-2.5 V). The results indicated that Al³⁺ doping of the compound did not affect the spinel structure but considerably improved the initial capacity and cycling performance, implying the spinel structure of Li₄Ti₅O₁₂ was more stable when Ti⁴⁺ was substituted by Al³⁺, and Al³⁺ doping was beneficial to the reversible intercalation and deintercalation of Li⁺. Al³⁺ doping improved the reversible capacity and cycling performance effectively especially when it was discharged to 0 V.     

Structural and thermal studies of PVA:NH4I

Proton-conducting polymer electrolytes based on poly vinyl alcohol (PVA; 88% hydrolyzed) and ammonium iodide (NH₄I) has been prepared by solution casting method with different molar ratios of polymer and salt using DMSO as solvent. DMSO has been chosen as a solvent due its high dielectric constant and also its plasticizing nature. The ionic conductivity has been found to increase with increasing salt concentration up to 25 mol% beyond which the conductivity decreases and the highest ambient temperature conductivity has been found to be 2.5×10⁻³ S cm⁻¹. The conductivity enhancement with addition of NH₄I has been well correlated with the increase in amorphous nature of the films confirmed from XRD and differential scanning calorimetry (DSC) analyses. The temperature-dependent conductivity follows the Arrhenius relation. The polymer-proton interactions have been analyzed by FTIR spectroscopy.     

The role of As2O3 on the stability and some physical properties of PbO-Sb2O3 glasses

PbO-Sb₂O₃ glasses added with different concentrations of As₂O₃ (10-55 mol%) were prepared to understand their IR spectra, elastic properties (Young's modulus E, Shear modulus G, microhardness H), optical absorption and dielectric properties (constant ε, loss tan δ, ac conductivity σ_ac over a moderately wide range of frequency and temperature and breakdown strength in air medium at room temperature). Results have indicated that the structure of the PbO-Sb₂O₃-As₂O₃ glass is more rigid when the concentration of As₂O₃ is around 40 mol%.     

Phase transformation behavior and dielectric characteristics of BaTi1−x(Al1/2Nb1/2)xO3 (0.01≤x≤0.40) ceramics

Microstructure, phase transformation behavior and dielectric properties of BaTi_1−x(Al_1/2Nb_1/2)_xO₃ (0.01≤x≤0.40) ceramics were investigated. A high level of (Al_1/2Nb_1/2)⁴⁺ substitution for Ti⁴⁺ ions was not conducive to the stability of the perovskite structure and resulted in the formation of BaAl₂O₄. As x was increased, lattice constants and unit cell volume decreased, reached a minimum at x=0.10 and then increased. The BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics at room temperature experienced a transformation from ferroelectric to paraelectric phase with increasing (Al_1/2Nb_1/2)⁴⁺ concentration. Meanwhile, permittivity of the BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics was markedly reduced, while Q value was slightly increased. Frequency dispersion of dielectric peak was obviously increased as x was increased from 0.01 to 0.10. It is of great interest that a dielectric abnormity represented by a broad dielectric peak at 200-400 K was observed for the composition with x=0.40.     

Study of phase transition in ZrO2 doped with Pb3O4

Electrical conductivity of ZrO₂ doped with Pb₃O₄ has been measured at different temperatures for different molar ratios (x=0, 0.01, 0.02, 0.03, 0.04, 0.05 and 0.06). The conductivity increases due to migration of vacancies, created by doping. The conductivity increases with increase in temperature till 180 °C and thereby decreases due to collapse of the fluorite framework. A second rise in conductivity at higher temperatures beyond 500-618 °C is due to phase transition of ZrO₂. DTA and X-ray powder diffraction were carried out for confirming doping effect and transition in ZrO₂.The addition of Pb₃O₄ to ZrO₂ shifted the phase transition of ZrO₂ due to the interaction between Pb₃O₄ and ZrO₂.     

Effect of Bi2O3 on EPR, optical transmission and DC conductivity of vanadyl doped alkali bismuth borate glasses

Glasses with composition xBi₂O₃·(30−x)M₂O·70B₂O₃ (M=Li, Na) containing 2 mol% V₂O₅ have been prepared over the range 0≤x≤15 (x is in mol%). The electron paramagnetic resonance spectra of VO²⁺ of these glasses have been recorded in the X-band (≈9.3 GHz) at room temperature (RT≈300 K). Spin Hamiltonian parameters, g_∥, g_⊥, A_∥, A_⊥, dipolar hyperfine coupling parameter, P, and Fermi contact interaction parameter, K, have been calculated. The molecular orbital coefficients, α² and γ², have been calculated by recording the optical transmission spectra. In xBi₂O₃·(30−x)Li₂O·70B₂O₃ glasses there is decrease in the tetragonality of the V⁴⁺O₆ complex for x up to 6 mol% whereas for x≥6 mol%, tetragonality increases. In xBi₂O₃·(30−x)Na₂O·70B₂O₃ glasses there is increase in the tetragonality of the V⁴⁺O₆ complex with increasing x. The 3d_xy orbit expands with increase in Bi₂O₃:M₂O ratio. Values of the theoretical optical basicity, Λ_th, have also been reported. The DC conductivity increases with increase in temperature. The order of conductivity is 10⁻⁵ ohm⁻¹ m⁻¹ at low temperature and 10⁻³ ohm⁻¹ m⁻¹ at high temperature. The DC conductivity decreases and the activation energy increases with increase in Bi₂O₃:M₂O ratio.     

Low-temperature sintering and microwave dielectric properties of Ca2Zn4Ti15O36 ceramics

The sintering behavior, microstructures, and microwave dielectric properties of Ca₂Zn₄Ti₁₅O₃₆ ceramics with B₂O₃ addition were investigated. The crystalline phases and microstructures of Ca₂Zn₄Ti₁₅O₃₆ ceramics with 0-10 wt% B₂O₃ addition were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The sintering temperature of Ca₂Zn₄Ti₁₅O₃₆ ceramic was lowered from 1170 to 930 °C by 10 wt% B₂O₃ addition. Ca₂Zn₄Ti₁₅O₃₆ ceramics with 8 wt% B₂O₃ addition sintered at 990 °C for 2 h exhibited good microwave dielectric properties, i.e., a quality factor (Qf) 11,400 GHz, a relative dielectric constant (ε_r) 41.5, and a temperature coefficient of resonant frequency (τ_f) 94.4 ppm/°C.     

Electrical behaviour of Li2O-ZnO-SiO2 glass and glass-ceramics system

Sealing quality lithium zinc silicate (LZS) glasses of compositions (wt.%) (a) LZSL- Li₂O: 12.65, ZnO: 1.85, SiO₂: 74.4, Al₂O₃: 3.8, K₂O: 2.95, P₂O₅: 3.15, B₂O₃: 1.2 (low ZnO), and (b) LZSH- Li₂O: 8.9, ZnO: 24.03, SiO₂: 53.7, Na₂O: 5.42, P₂O₅: 2.95, B₂O₃: 5 (high ZnO) were prepared by conventional melt-quench technique and converted to glass-ceramics by controlled crystallization process. The electrical properties of these samples were measured using ac impedance spectroscopy technique over a frequency range of 10 Hz-15 MHz at several temperatures in the range of 323-673 K. The ac conductivity, dc conductivity, dielectric constant and loss factor were obtained from these measurements. The dc conductivity (σ_dc) follows the Arrhenius behaviour with temperature. It is observed that σ_dc in LZSL glass is significantly higher than in the LSZH glass and the activation energies for σ_dc for LZSL and LZSH glasses are 0.59 and 1.08 eV, respectively. It further observed that the conductivity value decreases nearly one order of magnitude on conversion to glass-ceramics. The behaviour is explained on the basis of distributions and nature of alkali ions and network structures in these samples.     

Structural, vibrational and dielectric properties of new potassium hydrogen sulfate arsenate: K4(SO4)(HSO4)2(H3AsO4)

A new compound, K₄(SO₄)(HSO₄)₂(H₃AsO₄) was synthesized from water solution of KHSO₄/K₃H(SO₄)₂/H₃AsO₄. This compound crystallizes in the triclinic system with space group P1¯ and cell parameters: a=8.9076(2) Å, b=10.1258(2) Å, c=10.6785(3) Å; α=72.5250(14)°, β=66.3990(13)°, γ=65.5159(13)°, V=792.74(3) Å³, Z=2 and ρ_cal=2.466 g cm⁻³. The refinement of 3760 observed reflections (I>2σ(I)) leads to R₁=0.0394 and wR₂=0.0755. The structure is characterized by SO₄²⁻, HSO₄⁻ and H₃AsO₄ tetrahedra connected by hydrogen bridge to form two types of dimer (H(16)S(3)O₄⁻?S(1)O₄²⁻ and H(12)S(2)O₄⁻?H₃AsO₄). These dimers are interconnected along the [1¯ 1 0] direction by the hydrogen bonds O(3)-H(3)?O(6). They are also linked by the hydrogen bridge assured by the hydrogen atoms H(2), H(3) and H(4) of the H₃AsO₄ group to build the chain S(1)O₄?H₃AsO₄ which are parallel to the “a” direction. The potassium cations are coordinated by eight oxygen atoms with K-O distance ranging from 2.678(2) to 3.354(2) Å.Crystals of K₄(SO₄)(HSO₄)₂(H₃AsO₄) undergo one endothermic peak at 436 K. This transition detected by differential scanning calorimetry (DSC) is also analyzed by dielectric and conductivity measurements using the impedance spectroscopy techniques. The obtained results show that this transition is protonic by nature.     

Structural and electrical properties of high-energy ball-milled NASICON type Li1.3Ti1.7Al0.3(PO4)2.9(VO4)0.1 ceramics

Nano-crystallites of Li_1.3Ti_1.7Al_0.3(PO₄)_2.9(VO₄)_0.1 NASICON type material are prepared by means of solid-state reaction of a stoichiometric mixture after milling it for 22 and 55 h. The milling reduces the average crystallite size of the ceramic to 80 and 60 nm, respectively. Mechanical milling changes structural parameters and the strain induced at the grain-boundaries plays a major role in improving electrical conductivity. An order of magnitude increase in electrical conductivity is observed in the material milled for 55 h compared to the unmilled material, which is also reflected in permittivity loss. Modulus and permittivity representations substantiate the constriction effect of grain-boundaries observed in the complex impedance representation.     

Room temperature fabrication Oxide TFT with Y2O3 as a gate oxide and Mo contact

In this investigation, an operating voltage as low as 5 V has been achieved for Oxide TFT with Y₂O₃ as a gate oxide and a-IGZO as an active layer. The OTFT has been fabricated at room temperature using RF sputter. The mobility and threshold voltages are 11.3 cm²/V s and 3.4 V for the device with W/L = 0.8, respectively. The annealing at 400 °C in N₂ containing 5% H₂ ambient has been utilized to improve the electrical performance of TFT. The on-off current which is determined by gate dielectric has been observed to be 10⁴. It has also been observed that the dielectric properties of gate oxide deteriorate on annealing. The dielectric constant of Y₂O₃ is observed in the range between 5.1 and 5.4 measured on various devices.     

The electrical properties of dielectric stacks of SiO2 and Al2O3 prepared by atomic layer deposition method

We produced dielectric stacks composed of ALD SiO₂ and ALD Al₂O₃, such as SiO₂/Al₂O₃, Al₂O₃/SiO₂, and SiO₂/Al₂O₃/SiO₂, and measured the leakage currents through the stacks in comparison with those of the single oxide layers. SiO₂/Al₂O₃ shows lowest leakage current for negative bias region below 6.4 V, and Al₂O₃/SiO₂ showed highest current under negative biases below 4.5 V. Two distinct electron conduction regimes are observed for Al₂O₃ and SiO₂/Al₂O₃. Poole-Frenkel emission is dominant at the high-voltage regime for both dielectrics, whereas the direct tunneling through the dielectric is dominant at the low-voltage regime. The calculated transition voltage between two regimes for SiO₂ (6.5 nm)/Al₂O₃ (12.6 nm) is −6.4 V, which agrees well with the experimental observation (−6.1 V). For the same EOT of entire dielectric stack, the transition voltage between two regimes decreases with thinner SiO₂ layer.     

Reduced dielectric loss and leakage current in CaCu3Ti4O12/SiO2/CaCu3Ti4O12 multilayered films

The CaCu₃Ti₄O₁₂/SiO₂/CaCu₃Ti₄O₁₂ (CCTO/SiO₂/CCTO) multilayered films were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition method. It has been demonstrated that the dielectric loss and the leakage current density were significantly reduced with the increase of the SiO₂ layer thickness, accompanied with a decrease of the dielectric constant. The CCTO film with a 20 nm SiO₂ layer showed a dielectric loss of 0.065 at 100 kHz and the leakage current density of 6×10⁻⁷ A/cm² at 100 kV/cm, which were much lower than those of the single layer CCTO films. The improvement of the electric properties is ascribed to two reasons: one is the improved crystallinity; the other is the reduced free carriers in the multilayered films.     

Green and red up-conversion emissions of Er-Yb-codoped Al2O3 powders prepared by the nonaqueous sol-gel method

The 1 mol% Er³⁺- and 0-20 mol% Yb³⁺-codoped Al₂O₃ powders have been prepared by the nonaqueous sol-gel process using aluminum isopropoxide as precursor, acetylacetone as chelating agent, nitric acid as catalyzer, and hydrated erbium and ytterbium nitrate as dopant under isopropanol environment. The two crystalline types of doped Al₂O₃, γ and θ, and a stoichiometric compound, (Yb,Er)₃Al₅O₁₂, were obtained for all the Er³⁺-Yb³⁺-codoped Al₂O₃ powders at the sintering temperature of 1000 °C. The maximal intensity of both the green and red up-conversion emissions centered at about 523, 545, and 660 nm was observed for the 1 mol% Er³⁺- and 10 mol% Yb³⁺-codoped Al₂O₃ powders. The intensity ratio of the red to green up-conversion emission (I_red/I_green) increased with increasing the Yb³⁺ doping concentration for the Er³⁺-Yb³⁺-codoped Al₂O₃ powders. Furthermore, the intensity ratio of the green up-conversion emission at about 523 to 545 nm (I₅₂₃/I₅₄₅) was proportional to the Yb³⁺ doping concentration and pump electric current, which was associated with the elevated temperature of powders.