Correlation between microstructure and optical properties of nano-crystalline TiO2 thin films prepared by sol-gel dip coating

Titanium dioxide thin films have been prepared from tetrabutyl-orthotitanate solution and methanol as a solvent by sol-gel dip coating technique. TiO₂ thin films prepared using a sol-gel process have been analyzed for different annealing temperatures. Structural properties in terms of crystal structure were investigated by Raman spectroscopy. The surface morphology and composition of the films were investigated by atomic force microscopy (AFM). The optical transmittance and reflectance spectra of TiO₂ thin films deposited on silicon substrate were also determined. Spectroscopic ellipsometry study was used to determine the annealing temperature effect on the optical properties and the optical gap of the TiO₂ thin films. The results show that the TiO₂ thin films crystallize in anatase phase between 400 and 800 °C, and into the anatase-rutile phase at 1000 °C, and further into the rutile phase at 1200 °C. We have found that the films consist of titanium dioxide nano-crystals. The AFM surface morphology results indicate that the particle size increases from 5 to 41 nm by increasing the annealing temperature. The TiO₂ thin films have high transparency in the visible range. For annealing temperatures between 1000 and 1400 °C, the transmittance of the films was reduced significantly in the wavelength range of 300-800 nm due to the change of crystallite phase and composition in the films. We have demonstrated as well the decrease of the optical band gap with the increase of the annealing temperature.     

Bismuth zinc niobate (Bi1.5ZnNb1.5O7) ceramics derived from metallo-organic decomposition precursor solution

The preparation, microstructure development and dielectric properties of Bi_1.5ZnNb_1.5O₇ pyrochlore ceramics by metallo-organic decomposition (MOD) route are reported. Homogeneous precalcined ceramic powders of 13-36 nm crystallite size were obtained at temperatures ranging from 500 to 700 °C. The thermal decomposition/oxidation of the gelled precursor solution was chemically analyzed, TG/DTA, XRD, and SEM, led to the formation of a pure cubic pyrochlore phase with a stoichiometry close to Bi_1.5ZnNb_1.5O₇ which begins to form at 500 °C. The metallo-organic precursor synthesis method, where Bi, Zn and Nb ions are chelated to form metal complexes, allows the control of Bi/Zn/Nb stoichiometric ratio on a molecular scale leading to the rapid formation of bismuth zinc niobate (Bi_1.5ZnNb_1.5O₇) ceramic fine powders with pure pyrochlore structure. The powders were pressed into pellets and can be sintered at temperatures as low as 800-1000 °C. Fine crystalline ceramics with the grain size in the range of 200-500 nm have been obtained at the sintering temperature of 800 °C. The dielectric properties in high frequency to microwave range were measured and discussed.     

Polyol-assisted synthesis of TiO2 nanoparticles in a semi-aqueous solvent

TiO₂ (anatase and rutile) nanoparticles with an average crystallite size of 20-40 nm have been prepared at room temperature by polyol-mediated synthesis technique in a semi-aqueous solvent medium using titanium iso-propoxide as the titanium source, acetone as the oil phase and ethylene glycol as the stabilizer. Phase and microstructure of the resultant materials have been characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy and Raman spectroscopy. Photocatalytic degradation of acetaldehyde using TiO₂ nanoparticles was investigated by gas-chromatography technique.     

Structural properties of the titanium dioxide thin films grown by atomic layer deposition at various numbers of reaction cycles

A dependence of structural properties of TiO₂ films grown on both Si- and Ti-substrates by atomic layer deposition (ALD) at the temperature range of 250-300 °C from titanium ethoxide and water on the number of reaction cycles N was investigated using Fourier-transform infrared (FTIR) spectroscopy and X-Ray diffraction (XRD). TiO₂ films grown on both Si- and Ti-substrates revealed amorphous structure at low values of N < 400. However, an increase of N up to values 400-3600 resulted in the growth of polycrystalline TiO₂ with structure of anatase on both types of substrates and according to XRD-measurements the sizes of crystallites rose with the increase of N. The maximum anatase crystallite size for TiO₂ grown on Ti-substrate was found to be on ∼35% lower in comparing with that for TiO₂ grown on Si-substrate. A use of titanium methoxide as a Ti precursor with the ligand size smaller than in case of titanium ethoxide allowed to observe an influence of the ligand size on both the growth per cycle and structural properties of TiO₂. The average growth per cycle of TiO₂ deposited from titanium methoxide and water (0.052 ± 0.01 nm/cycle) was essentially higher than that for TiO₂ grown from titanium ethoxide and water (0.043 ± 0.01 nm/cycle). Ligands of smaller sizes were found to promote the higher crystallinity of TiO₂ in comparison with the case of using the titanium precursor with ligands of bigger sizes.     

Secondary ion mass spectrometry and X-ray photoelectron spectroscopy studies on TiO2 and nitrogen doped TiO2 thin films

Anatase phase TiO₂ and nitrogen (N) doped TiO₂ thin films were synthesized by an ultrasonic spray pyrolysis technique on c-Si (100) substrates in the temperature range 300-550 °C. The former used a precursor solution of titanium oxy acetylacetonate in methanol whereas the later used a titanium oxy acetylacetonate hexamine mixture in methanol. Homogeneity across the film’s thickness and the nature of the film-substrate interface were studied by dynamic depth profiling acquired using secondary ion mass spectrometry SIMS. The stoichiometry and bonding state of various species present in the films were studied using X-ray photoelectron spectroscopy (XPS). N-doping was confirmed by both SIMS and XPS. XPS studies revealed that the nitrogen content of the films synthesized at 300 °C (3.2%) is high compared to that of films made at 350 °C (1.3%).     

Effect of the crystallite size in the structural and textural properties of sulfated and phosphated titania

Sulfated and phosphated titania (TiO₂) were obtained by the sol-gel method. The sulfation was prepared in situ using sulfuric acid as hydrolysis catalyst, or by impregnation with ammonium sulphate. Phosphated sol-gel titania was synthesized with phosphoric acid. Long thermal treatments were carried out from 100 to 1000 °C to study the crystallization process of titania. All present phases were nanocrystalline, and the anatase-rutile polymorphic transformation was dependent on the crystallite size of the materials and on the preparation method. The smallest crystallite values were obtained for the phosphated samples. Titania sulfated by impregnation was found to be an efficient and selective catalyst towards propene, whereas di-isopropylether was obtained only in the catalyst prepared in situ with H₂SO₄.     

Photocatalytic hydroxyapatite/titanium dioxide multilayer thin film deposited onto glass using an rf magnetron sputtering technique

Hydroxyapatite (HA)/titanium dioxide (TiO₂) thin film was deposited on glass using a radio frequency magnetron sputtering. X-ray diffraction (XRD), Fourier-transform infrared spectrometry, ultraviolet-visible spectroscopy and measurement of its photocatalytic activity by the decomposition of formaldehyde gas and the bacterial survival test of Escherichia coli (E. coli) cells were applied to characterize the film. After heat treatment (at 500 °C), XRD analysis of the HA/TiO₂ film showed a crystalline TiO₂ crystal structure with anatase phase. The transmittance of the HA/TiO₂ film decreased after the heat treatment, however, the average transmittance remained at 87% in the visible light range.In the decomposition of formaldehyde gas, the HA/TiO₂ film showed a higher decomposition rate than either the TiO₂ or the HA film alone. However, in the bacterial survival test, survival of cells on the HA/TiO₂ film was higher than that on the TiO₂ film, which indicates the HA/TiO₂ film has a lower bactericidal effect than the TiO₂ film alone.     

Porous TiO2 microspheres with tunable properties for photocatalytic air purification

The synthesis of highly-crystalline porous TiO₂ microspheres is reported using ultrasonic spray pyrolysis (USP) in the presence of colloidal silica as a template. We have exploited the interactions between hot SiO₂ template particles surface and TiO₂ precursor that occur during reaction inside the droplets, to control the physical and chemical properties of the resulting particles. Varying the SiO₂ to titanium precursor molar ratio and the colloidal silica dimension, we obtained porous titania microspheres with tunable morphology, porosity, BET surface area, crystallite size, band-gap, and phase composition. In this regard, we have also observed the preferential formation of anatase vs. rutile with increasing initial surface area of the silica template. The porous TiO₂ microspheres were tested in the photocatalytic degradation of nitrogen oxides (NO_x) in the gas phase. USP prepared nanostructured titania samples were found to have significantly superior specific activity per surface area compared to a commercial reference sample (P25 by Evonik-Degussa).     

Size-controllable synthesis of functional heterostructured TiO<Subscript>2</Subscript>–WO<Subscript>3</Subscript> core–shell nanoparticles

Mono and bicomponent TiO₂ and WO₃ nanoparticles were synthesized inside Vycor^® glass pores, by cycles of impregnation of the glass with the respective oxide precursor followed by its thermal decomposition. The impregnation-decomposition cycle (IDC) methodology promoted a linear mass increase of the glass matrix, and allowed tuning the nanoparticle size. X-ray diffraction and Raman spectroscopy data allowed identifying the formation of TiO₂ as anatase phase, while WO₃ is a mixture of the γ-WO₃ (monoclinic) and δ-WO₃ (triclinic) phases. High resolution transmission electron microscopy images revealed that for 3, 5, and 7 IDC, the TiO₂ nanoparticles obtained presented average diameters of 3.4, 4.3, and 5.1 nm, and the WO₃ nanoparticles have 2.9, 4.6, and 5.7 nm sizes. These TiO₂ and WO₃ monocomponent nanoparticles were submitted to IDC with the other oxide precursor, resulting in bicomponent nanoparticles. The broadening and shift of the Raman bands related to titanium and tungsten oxides suggest the formation of hetero-structure core–shell nanoparticles with tunable core sizes and shell thicknesses.     

Sol-gel synthesis, characterization and optical properties of mercury-doped TiO2 thin films deposited on ITO glass substrates

The Hg-doped and undoped nano-crystalline TiO₂ films on ITO glass substrates surface and polycrystalline powders were prepared by sol-gel dip coating technique. The crystal structure and surface morphology of TiO₂ were characterized by means of X-ray diffractometer (XRD), atomic force microscope (AFM), spectrophotometer, Fourier-transform infrared (FTIR), and spectroscopic ellipsometry (SE). The results indicated that the powder of TiO₂, doped with 5% Hg in room temperature was only composed of the anatase phase whereas in the undoped powder exhibits an amorphous phase were present. After heat treatments of thin films, titanium oxide starts to crystallize at the annealing temperature 400 °C. The average crystallite size of the undoped TiO₂ films was about 8.17 nm and was increased with Hg-doping in the TiO₂ films. Moreover, the grains distributed more uniform and the surface roughness was greater in the Hg-doped TiO₂ films than in the undoped one. Refractive index and porosity were calculated from the measured transmittance spectrum. The values of the index of refraction are in the range (1.95-2.49) and the porosity is in the range (47-2.8). The coefficient of transmission varies from 60 to 90%. SE study was used to determine the annealing temperature effect on the optical properties in the wavelength range from 0.25 to 2 μm and the optical gap of the Hg-doped TiO₂ thin films.     

Photocatalytic Activity of N-doped TiO2 Photocatalysts Prepared from the Molecular Precursor (NH4)2TiO(C2O4)2

用不同温度控制分解草酸氧钛铵制备N掺杂TiO₂光催化剂．利用XRD、IR、热分析、N₂吸-脱附等温线、XPS、紫外可见漫反射光谱和SEM表征了N-TiO₂光催化剂的结构．400～600 oC焙烧的N-TiO₂光催化剂为纯锐钛矿相,而700 oC焙烧的N-TiO₂光催化剂为锐钛矿和金红石混合相．N掺杂在TiO₂的间隙位使锐钛矿相TiO₂带隙变窄．在光降解甲基橙的反应中,600和400 oC焙烧的N-TiO₂催化剂分别在紫外光和全波长光照射下有最好活性;700 oC焙烧的N-TiO₂催化剂无论在紫外光和全波长光下都表现出最好的比活性,即最高的光量子效率,这可以归因于700 oC焙烧的N-TiO₂光催化剂良好的结晶程度和锐钛矿-金红石异相结的存在．     

Effect of additives and precursor chemical structure on crystalline shape and optical properties of TiO2

This paper proposes a new simple approach for synthetic of shape-defined anatase nanocuboids TiO₂ by using combination of titanium tetra isopropoxide (TTIP) and orthotitanic acid (H₄TiO₄) as titanium precursor. In first step by adding precursor to ethanol solution mixed with HCl the primary sol has been prepared, therefore two other different films by adding Methylcellulose (MC) as a carbon containing material and adding TiO₂ nanopowder as nanofiller have been prepared and properties of thin film as a function of parameters of annealing temperature and additives, have been discussed. The films were deposited on glass substrates and characterized by using UV–vis spectroscopy and scanning electron microscopy (SEM). SEM results show that optical properties of TiO₂ thin films were changed by baking in 300, 400 and 500 °C as annealing temperature. Moreover, they indicate that the additives have strong effect on anatase structure and therefore influence the optical properties.     

Investigation of chemical decomposition of CCl4 on TiO2 near room temperature

Dissociative adsorption of CCl₄ on TiO₂ at 35 °C has been studied by Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, and electron spin resonance. CCl₄ decompose to form CO, CO₂, and CO₃ on the surface, at such a low temperature, in which CO₂ formation is not from CO oxidation on TiO₂, but CO₃ can be produced by CO and CO₂ adsorption. The Cl generated from CCl₄ decomposition is left on the surface and bonded to titanium ions. Mineralization of CCl₄ on TiO₂ involves the lattice oxygens. Thermodynamical driving force and possible reaction routes for CO and CO₂ formation in the CCl₄ decomposition on TiO₂ are discussed.     

Decomposition of gaseous toluene on thermally-excited titanium dioxide and its ESR study under high temperatures

Decomposition of gaseous toluene on thermally-excited activated titanium dioxide (TiO₂) was investigated using a simple flow system. The decomposition of toluene on the TiO₂ bead was 92% at 400 °C. The irregular phenomena in the toluene decomposition at around 300 °C seemed to be due to the coloration of the TiO₂ bead. Electron spin resonance (ESR) measurement at high temperatures was carried out using the heating unit. Since the g-value of the signal was 1.996, the existence of Ti³⁺ in TiO₂ material was confirmed. That is, oxygen vacancy generated by thermally-excitation of TiO₂, and the reaction activity of the TiO₂ bead for gaseous toluene must be due to spins on the material.     

Role of the TiO6 octahedra on the ferroelectric and piezoelectric behaviour of the poled PbMg1/3Nb2/3O3-xPbTiO3 (PMN-PT) single crystal and textured ceramic

Field cooling (FC) poled/unpoled PMN-29%PT single crystal and room temperature (RT) poled/unpoled PMN-34.5%PT textured ceramic were investigated between ∼0 and 300 °C by thermal expansion, dielectric and Raman spectroscopy. New phase transitions are evidenced at 40, 91 and 180 °C in the case of FC PMN-29%PT as well as at 70 and 200 °C for RT PMN-34.5%PT and their order is discussed. The physical properties of the textured ceramics are rather similar to the ones observed for the single crystals that make them low-cost alternative for a wide range of applications. However, the temperatures and character of the phase transitions strongly depend on the kind of the poling conditions. Temperature dependences of the Raman line parameters show that the NbO₆ octahedra remain stable during temperature increase, while TiO₆ ones evolve quasi-continuously. The step transitions of the Pb²⁺ ion sublattice are evidenced. This suggests that the TiO₆ and Pb²⁺ sublattices are especially coupled. The role of the TiO₆ clusters on the structural phase transitions and dielectric properties of the PbMg_1/3Nb_2/3O₃-xPbTiO₃ (PMN-PT) system is discussed. The presence of the Raman modes above the maximum dielectric permittivity reveals that the local symmetry is lower than the cubic one (Pm3m). The decrease of the Raman line intensities vs. temperature indicates precisely the continuous evolution of the local symmetry towards the cubic one. The temperature evolution of the Rayleigh wing parameters appears sensitive to the phase transitions’ presence.     

Microstructure and infrared emissivity property of coating containing TiO2 formed on titanium alloy by microarc oxidation

Ceramic coatings containing TiO₂ were formed on Ti6Al2Zr1Mo1V alloy surface by microarc oxidation (MAO) method. The microstructure, phase and chemical composition of the coatings were analyzed by SEM, XRD and EDS techniques. The coating mainly consists of rutile TiO₂ and a small amount of anatase TiO₂. The infrared emissivity values of coated and uncoated titanium samples when exposed to 700 °C were tested. It was found that the coating exhibits a higher infrared emissivity value (about 0.9) in the wavelength range of 8–14 μm than that of the uncoated titanium alloy, although which shows a slight increase from 0.1 to 0.3 with increasing exposure time at 700 °C. The relatively high infrared emissivity value of the MAO coating is possibly attributed to the photon emission from the as formed TiO₂ phase.     

XRD and XPS characterization of mixed valence Mn3O4 hausmannite thin films prepared by chemical spray pyrolysis technique

Spray pyrolysis technique has been employed successfully for the synthesis of single phase mixed valence spinel hausmannite (Mn₃O₄) thin films using alcoholic start solution of manganese acetate (Mn(CH₃COO)₂·4H₂O) on pyrex glass substrates at atmospheric pressure using air as a carrier gas. Thermal decomposition of the precursor in the temperature range 320-490 °C led to the formation of Mn₃O₄ phase as revealed from the thermogravimetry analysis. Prepared samples are characterized by X-ray diffraction that shows spinel structure with space group I4₁/amd. Pure and well crystallized specimen is subjected to X-ray photoelectron spectroscopy for the surface chemistry investigation of these systems at a molecular level. Surface Mn/O ratio is compared to the bulk composition of the sample. Atomic force micrographs revealed that the morphology and the surface grains of the films largely influenced by the substrate temperature.     

Investigation of IrO2-SnO2 thin film evolution from aqueous media

The thermal evolution process of IrO₂-SnO₂/Ti mixed oxide thin films of varying noble metal content has been investigated under in situ conditions by thermogravimetry-mass spectrometry, Fourier transform infrared emission spectroscopy and cyclic voltammetry. The gel-like films prepared from aqueous solutions of the precursor salts Sn(OH)₂(CH₃COO)_2−xCl_x and H₂IrCl₆ on titanium metal support were heated in an atmosphere containing 20% O₂ and 80% Ar up to 600 °C.The thermal decomposition reactions practically take place in two separate temperature ranges from ambient to about 250 °C and between 300 and 600 °C. In the low temperature range the liberation of solution components and - to a limited extent - an oxidative cracking reaction of the acetate ligand takes place catalyzed by the noble metal. In the high temperature range the evolution of chlorine as well as the decomposition of surface species formed (carbonyls, carboxylates, carbonates) can be observed. The acetate ligand shows extreme high stability and is decomposed in the 400-550 °C range, only.Since the formation and decomposition of the organic surface species can significantly influence the morphology (and thus the electrochemical properties) of the films, the complete understanding of the film evolution process is indispensable to optimize the experimental conditions of electrode preparation.     

Effect of calcination temperature on the morphology and surface properties of TiO2 nanotube arrays

Well-ordered TiO₂ nanotube arrays were prepared by electrochemical anodization of titanium in aqueous electrolyte solution of H₃PO₄ + NH₄F at a constant voltage of 20 V for 3 h, followed by calcined at various temperatures. X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and Photoluminescence (PL) were used to characterize the samples. The results showed that the as-prepared nanotube arrays before being calcined were amorphous and could transform to anatase phase at a heat treatment temperature higher than 400 °C. As the calcination temperatures increased, crystallization of anatase phase enhanced and rutile phase appeared at 600 °C. However, further increasing the calcination temperature would cause the collapse of nanotube arrays. PL intensity of the nanotube arrays annealed at 500 °C was the lowest, which was probably ascribed to better crystallization together with fewer surface defects of the nanotube arrays.     

Preparation and characterization of nitrogen-doped TiO2 nanoparticles by the laser pyrolysis of N2O-containing gas mixtures

Nitrogen-doped TiO₂ nanoparticles have been prepared by the IR laser pyrolysis technique. A sensitized mixture of TiCl₄ (vapors) and N₂O was used as titanium and nitrogen precursors, respectively. The structural properties of the resultant N-doped nanoparticles such as the phase formation and the average particle size and distributions were investigated by X-ray diffraction, transmission electron microscopy and X-ray photoelectron spectroscopy. The phase composition varied from almost pure anatase to mixtures of rutile and anatase. A decrease of the mean particle diameters from about 18 nm in case of the almost pure anatase sample to about 13 nm in case of the anatase-rutile mixture is observed. XPS analysis suggests and interstitial character of the doping process.