Anodic characterization of mercury microelectrodes for determinations of anions in real samples

The anodization of mercury microelectrodes was investigated in synthetic samples containing several strong and weak electrolytes at different concentrations. In particular, the effects on mercury anodization due to the presence of NaOH, HClO₄, NaCl, NaI, NaF, Na₂SO₄, NaHCO₃, Na₂CO₃, tartaric and citric acids, were studied in solutions containing either each species or mixtures of them, and without addition of supporting electrolyte. Some of the electrode processes studied led to linear calibration plots e.g. 1 × 10⁻⁵ − 1 × 10⁻⁴M Cl⁻, 1 × 10⁻⁶ − 1 × 10⁻⁵M I⁻, 5 × 10⁻⁴ − 3 × 10⁻³M SO₄²⁻, 5 × 10⁻⁴ − 2 × 10⁻²M HCO₃⁻, with typical correlation coefficients of 0.998–0.999. The anodization of mercury microelectrodes was also investigated directly in wine, rain, tap and mineral water, without pretreatment and without addition of supporting electrolyte. In the real samples only the ions Cl⁻ and HCO₃⁻ could be quantified, and the values found were in agreement, within 3–5%, with the reference values obtained by using Italian standard methods for food.     

Kinetics and mechanisms of the redox reaction of hexaaquotitanium(III) and the ethylenediamine tetraacetato titanium(III) complex by aqueous solutions of bromine

At 25°C, I = 1.0 M (CF₃SO₃⁻Li⁺+CF₃SO₃H), [H⁺] = 0.034–0.274 M and λ = 453 nm, the rate equation for the oxidation of Ti(H₂O), ₆³⁺ by bromine was found to be: −d/[Br₂]T/dt=kK/[Br₂][Ti^III]/[H⁺]+K+kK/[Br₃⁻][Ti^III]/[H⁺+K, where k = 9.2 × 10⁻³ M ⁻¹ s ⁻¹ and K = 4.5 × 10⁻³ M. At [H⁺] = 1.0 M, [Br⁻] = 0.05–0.4 M, the apparent second-order rate constant decreases as [Br⁻] increases.

The pH-dependence of the oxidation of Ti^III-edta by bromine is interpreted in terms of the change in identity of the Ti^III-edta species as the pH of the reaction medium changes. The second-order rate constants were fitted using a non-linear least-square computer program with (1/k₀^edta)² weighting into an equation of the form: k₀^edta =k₁+k₂K₁[H⁺]⁻¹+k₃K₁K₂[H⁺]^−2/1+K₁[H⁺[H⁺⁻¹+K₁K₂[H⁺]⁻², with K₁ and K₂ fixed as earlier determined at 9.55 × 10⁻³ and 2.29 × 10⁻⁹ M, respectively, for the oxidation of bromine. k₁=k₂=(3.1±0.32)×10³M⁻¹s⁻¹ k₃=(2.3±0.45)×10⁶N⁻¹s⁻¹.

It is proposed that these electron transfer reactions proceed by univalent changes with the production of Br₂^.− as a transient intermediate. An outer-sphere mechanism is proposed for these reactions. The homonuclear exchange rate for Ti^III-edta+Ti^IV-edta is estimated at 32 M⁻¹ s⁻¹.     

Time-resolved vibrational cemiluminescence: Rate constants for the reaction F + HC1 → HF + Cl and for the relaxtion of HF(v = 3) by HCl, CO2, N2O, CO, N2 and O2

The reaction: F + HCl→ HF (v 3) + Cl (1), has been initiated by photolysing F₂ using the fourth-harmonic output at 266 nm from a repetitively pulsed Nd: YAG laser By analysing the time-dependence of the HF(3,0) vibrational chemiluminescence, rate constants have been determined at (296 ± 5) K for reaction (1), k₁ = (7.0 ± 0.5) × 10⁻¹² cm³ molecule⁻¹ s⁻¹, and for the relaxation of HF(v = 3) by HCl, CO₂, N₂O, CO, N₂ and O₂: k_HCl = (1.18 ±0.14) × 10⁻¹¹ k_CO2 = (1.04 ± 0. 13) × 10⁻¹², k_N2O = (1.41 ± 0.13) × 10⁻¹¹ k_CO = (2.9 ± 0.3) × (10⁻¹², k_N2 = (7.1 ± 0.6) × 10⁻¹⁴ and k_O2 = (1.9 ± 0.6) × 10⁻¹⁴ cm³molecule⁻¹s⁻¹.     

Effect of presence of 18-crown-6 on the response of 1-pyrrolidine dicarbodithioate-based lead selective electrode

The lipophilic ammonium salt of 1-pyrrolidine dicarbodithioic acid (PCDT)[I] was introduced as a selective ionophore for a sensitive Pb-ion selective electrode. Also, the effect of immobilization of 18-crown-6 (CW), into the above membrane, on the electrode performance was discussed. The slope of the PCDT-based [I] electrode was (26–30 mV decade⁻¹), while it was (29-30 mV decade⁻¹) for (PCDT+CW)-based [II] electrode according to the doping time. The linear concentration ranges were (1×10⁻⁶–1×10⁻¹ M) and (5×10⁻⁵–1×10⁻¹ M) for electrode types [I] and [II] after one-day doping. The working pH ranges were (5.0–10.0) and (7.0–10.0) for electrode types [I] and [II], respectively. Most of the common cations were tested for the evaluation of the electrode selectivity with correlation to the ionic radii of the tested cations. Among them only Na⁺, Ag⁺ and Fe³⁺ were the real interference. Application of using the electrode for the determination of lead in lubrication oil samples was performed with RSD (0.86–1.03%). The obtained results were compared to those of an atomic absorption spectrophotometric method.     

Flow-injection chemiluminescence determination of tetracyclines with in situ electrogenerated bromine as the oxidant

By designing a novel flow-through electrolytic cell (FEC), bromine was produced near to the surface of the platinum electrode by electrochemical oxidation of acidic KBr. The fast and weak chemiluminescence signal produced by the chemical reaction of the electrogenerated bromine with H₂O₂ was greatly enhanced by tetracyclines Based on these observations, a new, sensitive and simple electrogenerated chemiluminescence (ECL) method for the determination of tetracyclines was developed. Under the optimum experimental conditions, the calibration graphs are linear over the range 3.0×10⁻⁸ to 5.0×10⁻⁵ g ml⁻¹ for tetracycline, 2.0×10⁻⁷ to 2.4×10⁻⁵ g ml⁻¹ for oxytetracycline and 1.0×10⁻⁷ to 5.0×10⁻⁵ g ml⁻¹ for chlortetracycline. The limits of detection (S/N=3) are 1.0×10⁻⁸ g ml⁻¹ for tetracycline, 7.0×10⁻⁸ g ml⁻¹ for oxytetracycline and 1.5×10⁻⁷ g ml⁻¹ for chlortetracycline. For the determination 5.0×10⁻⁷ g ml⁻¹ tetracycline, the relative standard deviation was <5%. The proposed method was used to determine tetracyclines in pharmaceutical formulations.     

Simultaneous determination of selenium and lead in whole blood samples by differential pulse polarography

The polarographic reduction of lead in the presence of selenite gives rise to an additional peak corresponding to the reduction of lead (Pb) on adsorbed selenium (Se) on mercury at −0.33 V. The selenium and lead content can be determined using this peak by the addition of a known amount of one of these ions first and then the second ion. The linear domain range of lead is 5.0×10⁻⁷–2.0×10⁻⁵ M and for selenium 5.0×10⁻⁷–1.0×10⁻⁵ M. Using this method 4.90×10⁻⁷ M Se(IV) and 1.47×10⁻⁶ M Pb(II) in a synthetic sample could be determined with a relative error of +2.0% and 1.8%, respectively (n=4). A recovery test after acid digestion for a synthetic sample was 97% for selenium and 96.5% for lead. The method was applied to 1 ml of digested blood, and 328±23 μg l⁻¹ Se(IV) and 850±62 μg l⁻¹ Pb(II) could be determined with a 90% (n=5) confidence interval.     

Dynamics of electronic polarization in molecular crystals

Dynamics of electronic polarization in the vicinity of charge carriers in molecular crystals is for the first time investigated here in connection with the carrier transport and intramolecular vibronic polarization. According to standard picture it has been assumed that the electronic polarization relaxation time is extremely short, as estimated from the relation τ_c = τ_d1 ≈ h/E_exc, where E_exc is the energy of the first single exciton state. In the case of anthracene (Ac) crystals, the value of τ_e is about 2 × 10⁻¹⁶ s, i.e. by several orders of magnitude shorter than a typical hopping (residence) time of charge carriers τ_h = 10⁻¹⁴ -10⁻¹³ s. It is argued that typical time of full reconstruction of the electronic polarization after individual carrier hops equals, in the slow carrier regime, approximately to t_d2 ≈ h/ΔE_exc is the width of the lowest singlet-exciton band. In Ac, this means t_d2 ≈ 0.73 × 10⁻¹⁴ s. Physical implications of this relatively high value of t_d2 in connection with carrier transport and molecular (vibronic) polarization are discussed.     

Acidity constants of benzidine in aqueous solutions

The acidity constants of benzidine (Bz) in aqueous solutions determined potentiometrically at 25° were K_a1 = (1.11 ± 0.08) × 10⁻⁵, K_a2 = (1.45 ± 0.12) × 10⁻⁴. The apparent mixed constants in 0.1M sodium nitrate are K_a1 = (5.37 ± 0.28) × 10⁻⁶ and K_a2 = (1.14 ± 0.09) × 10⁻⁴. The ultraviolet spectra were recorded as a function of pH and analysed with these constants to obtain the absorption spectra of H₂Bz²⁺, HBz⁺ and Bz; the corresponding wavelengths of maximal absorption are 247, 273 and 278 nm, and molar absorptivities 1.63 × 10⁴, 1.76 × 10⁴ and 2.26 × 10⁴ 1.mole⁻¹.cm⁻¹.     

Simultaneous potentiometric determination of ClO(3)(-)-ClO(2)(-) and ClO(3)(-)-HClO by flow injection analysis using Fe(III)-Fe(II) potential buffer

A rapid potentiometric flow injection technique for the simultaneous determination of oxychlorine species such as ClO₃⁻–ClO₂⁻ and ClO₃⁻–HClO has been developed, using both a redox electrode detector and a Fe(III)–Fe(II) potential buffer solution containing chloride. The analytical method is based on the detection of a large transient potential change of the redox electrode due to chlorine generated via the reaction of the oxychlorine species with chloride in the potential buffer solution. The sensitivities to HClO and ClO₂⁻ obtained by the transient potential change were enhanced 700–800-fold over that using an equilibrium potential. The detection limit of the present method for HClO and ClO₂⁻ is as low as 5×10⁻⁸ M with use of a 5×10⁻⁴ M Fe(III)–1×10⁻³ M Fe(II) buffer containing 0.3 M KCl and 0.5 M H₂SO₄. On the other hand, sensitivity to ClO₃⁻ was low when a potential buffer solution containing 0.5 M H₂SO₄ was used, but could be increased largely by increasing the acidity of the potential buffer. The detection limit for ClO₃⁻ was 2×10⁻⁶ M with the use of a 5×10⁻⁴ M Fe(III)–1×10⁻³ M Fe(II) buffer containing 0.3 M KCl and 9 M H₂SO₄. By utilizing the difference in reactivity of oxychlorine species with chloride in the potential buffer, a simultaneous determination method for a mixed solution of ClO₃⁻–ClO₂⁻ or ClO₃⁻–HClO was designed to detect, in a timely manner, a transient potential change with the use of two streams of potential buffers which contain different concentrations of sulfuric acid. Analytical concentration ranges of oxychlorine species were 2×10⁻⁵–2×10⁻⁴ M for ClO₃⁻, and 1×10⁻⁶–1×10⁻⁵ M for HClO and ClO₂⁻. The reproducibility of the present method was in the range 1.5–2.3%. The reaction mechanism for the transient potential change used in the present method is also discussed, based on the results of batchwise experiments. The simultaneous determination method was applied to the determination of oxychlorine species in a tap water sample, and was found to provide an analytical result for HClO, which was in good agreement with that obtained by the o-tolidine method and to provide a good recovery for ClO₃⁻ added to the sample.     

Flow injection visible diffuse reflectance quantitative analysis of nickel

Flow injection (FI) methodology, using diffuse reflectance in the visible region of the spectrum, for the analysis of nickel, precipitated in the form of dimethylglyoximate, is presented. A reflectance cell, constructed in polytetrafluoroethylene, using a LED (light emitting diode) as light source and a LDR (light dependent resistor) as detector, is described. The analytical signal (S) correlates with nickel concentration (C) between 1.6 × 10⁻⁴ and 6.6 × 10⁻⁴ mol L⁻¹. This correlation is described by the equation S = −1.108 + 3.314 × 10⁴C − 2.081 × 10⁷C² (r = 0.9996). The experimentally observed limit of detection is about 1.3 × 10⁻⁴ mol L⁻¹, as in lower concentrations the formation of precipitate is not observed. The experimental quantitation limit is about 1.6 × 10⁻⁴ mol L⁻¹. The mean R.S.D. (relative standard deviation) is about 2.7%. Samples containing nickel were analyzed and the results obtained in this method were compared with those of other methods using the statistical Student's t-test.     

Kinetics of the autoxidation of vitamin A catalysed by cobalt ion

Vitamin A,dissolved in liquid paraffin, is stable below room temperature, but suffers oxidative decomposition at 80°, giving its epoxide as the main product. The rate of decomposition of vitamin A (V_A) at 80° in the presence of oxygen (partial pressure of p) and a small amount of cobaltous stearate (Co) is expressed as: d[V_A]/dt = 3·15 × 10⁻¹:[V_A][Co] p^1·48 + 1·51 × 10⁻⁵[V_A]p^0·33 + 0·33 × 10⁻⁵[V_A], where the last term represents the spontaneous thermal decomposition.     

Rate constants for the reaction of OH radicals with CH3CN, C2H5CN AND CH2=CH-CN in the temperature range 298–424 K

Rate constants for the reactions of OH with CH₃CN, CH₃CH₂CN and CH₂=CH-CN have been measured to be 5.86 × 10⁻¹³ exp(−1500 ± 250 cal mole⁻¹/RT), 2.69 × 10⁻¹³ exp(−1590 ± 350 cal mole⁻¹/RT and 4.04 × 10⁻¹² cm³ molecule⁻¹ s⁻¹, respectively in the temperature range 298–424 K. These results are discussed in terms of the atmospheric lifetimes of nitrfles.     

Determination of pK(a)'s for thymol blue in aqueous medium: evidence of dimer formation

Formation constants for recrystallized thymol blue were determined in water, using the SQUAD and SUPERQUAD programs. The best model correlating spectrophotometric, potentiometric and conductimetric data was fitted with the dissociation of HL⁻=L²⁻+H⁺−log K=8.918±0.070 and H₃L₂⁻=2L²⁻+3H⁺−log K=29.806±0.133 with the SUPERQUAD program at variable low ionic strength (1.5×10⁻⁴–3.0×10⁻⁴ M); and HL=L²⁻+H⁺−log K=8.9±0.000, H₃L₂⁻ =2L²⁻+3H⁺−log K=30.730±0.032, H₄L₂=2L²⁻+4H⁺−log K=32.106±0.033 with SQUAD at 1.1 M ionic strength.     

PVC membrane based potentiometric sensors for uranium determination

Two novel uranyl PVC matrix membrane sensors responsive to uranyl ion are described. The first sensor incorporates tris(2-ethylhexyl)phosphate (TEHP) as both electroactive material and plasticizer and sodium tetraphenylborate (NaTPB) as an ion discriminator. The sensor displays a rapid and linear response for UO₂²⁺ ions over the concentration range 1×10⁻¹–2×10⁻⁵ mol l⁻¹ UO₂²⁺ with a cationic slope of 25.0±0.2 mV decade⁻¹. The working pH range is 2.8–3.6 and the life span is 4 weeks. The second sensor contains O-(1,2-dihydro-2-oxo-1-pyridyl)-N,N,N′,N′-bis(tetra-methylene)uronium hexafluorophosphate (TPTU) as a sensing material, sodium tetraphenylborate as an ion discriminator and dioctyl phenylphosphonate (DOPP) as a plasticizer. Linear and stable response for 1×10⁻¹–5×10⁻⁵ mol l⁻¹ UO₂²⁺ with near-Nernstian slope of 27.5±0.2 mV decade⁻¹ are obtained. The working pH range is 2.5–3.5 and the life span of the sensor is 6 weeks. Interference from many inorganic cations is negligible for both sensors. However, interference caused by some ions (e.g. Th⁴⁺, Cu²⁺, Fe³⁺) is eliminated by a prior ion exchange or solvent extraction step. Direct potentiometric determination of as little as 5 μg ml⁻¹ uranium in aqueous solutions shows an average recovery of 97.2±1.3%. Application for the determination of uranium at levels of 0.01–1 wt.% in naturally occurring and certified ores gives results with good correlation with data obtained by X-ray fluorescence.     

Reusable ethanol sensor based on a NAD-dependent dehydrogenase without coenzyme addition

An amperometric sensor for the detection of ethanol has been designed. The sensing layer consists of alcohol dehydrogenase (ADH), NADH oxidase and NAD⁺-dextran, entrapped together in a matrix of poly(vinyl alcohol) bearing styrylpyridinium groups (PVA-SbQ). Measurements have been carried out at a low oxidizing potential (equivalent to 250 mV vs. SCE) to detect hexacyanoferrate(II), thus avoiding interferences due to presence of oxidizable compounds in real samples. The influence of the amount of polymer, enzymes and coenzyme in the sensing layer on the sensor sensitivity, linear range and operational stability has been studied. The sensitivity was close to 2 mA 1 mol⁻¹, with a linear range 3 × 10⁻⁷ −2 × 10⁻⁴M and a response time <2 min. Good operational stability was observed, allowing more than 40 reproducible assays without NAD⁺ addition. Alcoholic beverages were analysed with the use of sensor and the results showed good correlation with those obtained using a standard spectrophotometric procedure.     

Phosphorescence of biacetyl sensitized by benzene in gas phase pulse radiolysis

The phophorescence of biacetyl induced by an energy transfer to biacetyl from triplet benzene produced in the pulse radiolysis of benzene-biacetyl mixtures has been studied. The time required to reach the maximum intensity of phosphorescence, t_max, after the electron pulse, varies as a function of biacetyl pressure at constant benzene pressure (40 torr), which gives the lifetime of triplet benzene τ = (6.7 ± 3.2) × 10⁻⁶ s and the rate constant of the energy transfer k_{C6H6^*(T1) + biacetyl} = (1.6 ± 0.7) × 10⁻¹⁰ cm³ molecule⁻¹ s⁻¹.     

Kinetic–catalytic–spectrophotometric determination of low concentrations of molybdenum in white wines

The paper describes the determination of the molybdenum content in white wines based on its catalytical action on the kalium iodide oxidation by hydrogen peroxide in acid medium.

The optimum reaction conditions (the catalyst, KI and H₂O₂ concentrations, the pH value, the order of the reagent additions, the temperature) have been found by studying the effect of the reaction variables.

The influence of some metallic ions (Ca²⁺, Mg²⁺, Zn²⁺, Cd²⁺, Fe²⁺ and Fe³⁺) and complexing anions (F⁻, C₂O²⁻₄, EDTA⁴⁻) on the catalyzed reaction rate was elucidated.

The molybdenum concentration was estimated by the tangent, fixed-time and fixed-absorbance method. The obtained average values for molybdenum content in white wines are within the 1.77×10⁻⁷–1.83×10⁻⁷ mol l⁻¹ range.     

Kinetic study of gas-phase Lu(D3/2) with O2, N2O and CO2

The second-order rate constants of gas-phase Lu(²D_3/2) with O₂, N₂O and CO₂ from 348 to 573 K are reported. In all cases, the reactions are relatively fast with small barriers. The disappearance rates are independent of total pressure indicating bimolecular abstraction processes. The bimolecular rate constants (in molecule⁻¹ cm³ s⁻¹) are described in Arrhenius form by k(O₂)=(2.3±0.4)×10⁻¹⁰exp(−3.1±0.7 kJmol⁻¹/RT), k(N₂O)=(2.2±0.4)×10⁻¹⁰exp(−7.1±0.8 kJmol⁻¹/RT), k(CO₂)=(2.0±0.6)×10⁻¹⁰exp(−7.6±1.3 kJmol⁻¹/RT), where the uncertainties are ±2σ.     

New aspects of the reaction of silver(I) cations with the ethylenediaminetetraacetate ion

The highly neutralized ethylenediaminetetraacetate (EDTA) titrant (95–99% as Y⁴⁻ anion) precipitates with Ag⁺ cations to form the Ag₄Y species, in aqueous medium, which is well characterized from conductometric titration, thermal analysis and potentiometric titration of the silver content of the solid. The precipitate dissolves in excess Y⁴⁻ to form a complex, AgY³⁻. Equilibrium studies at 25°C and ionic strength 0.50 M (NaNO₃) have shown from solubility and potentiometric measurements that the formation constant (95% confidence level) β₁ = (1.93 ± 0.07) × 10⁵ M⁻¹ and the solubility products are K_S0 = [Ag +]⁴[Y⁴⁻] = (9.0 ± 0.4) × 10⁻¹⁸ M⁵ and K_S1 = [Ag +]³[AgY³⁻] = (1.74 ± 0.08) × 10⁻¹² M⁴. The presence of Na⁺, rather than ionic strength, markedly affects the equilibrium; the data at ionic strength 0.10 M are: β₁ = (1.19 ± 0.03) × 10⁶ M⁻¹, K_S0 = (1.6 ± 0.4) × 10⁻¹⁹ M⁵ and K_S1 = (1.9 ± 0.5) × 10⁻¹³ M⁴; at ionic strength tending to zero; β₁ = (1.82 ± 0.05) × 10⁷ M⁻¹, K_S0 = (2.6 ± 0.8) × 10⁻²² M⁵ and K_S1 = (5 ± 1) × 10⁻¹⁵ M⁴. The intrinsic solubility is 2.03 mM silver (I) in 0.50 M NaNO₃. Well-defined potentiometric titration curves can be taken in the range 1–2 mM with the Ag indicator electrode. Thermal analysis revealed from differential scanning calorimetry a sharp exothermic peak at 142°C; thermal gravimetry/differential thermal gravimetry has shown mass loss due to silver formation and a brown residue, a water-soluble polymeric acid (decomposition range 135–157°C), tending to pure silver at 600°C, consistent with the original Ag₄Y salt.     

Synthesis, crystal structure and third-order non-linear optical property of heterobimetallic cluster compound [MoOICu3S3(2,2′-bipy)2]

Nest-shaped cluster [MoOICu₃S₃(2,2′-bipy)₂] (1) was synthesized by the treatment of (NH₄)₂MoS₄, CuI, (n-Bu)₄NI, and 2,2′-bipyridine (2,2′-bipy) through a solid-state reaction. It crystallizes in monoclinic space group P2₁/n, a=9.591(2) Å, b=14.820(3) Å, c=17.951(4) Å, β=91.98(2)°, V=2549.9(10) ų, and Z=4. The nest-shaped cluster was obtained for the first time with a neutral skeleton containing 2,2′-bipy ligand. The non-linear optical (NLO) property of [MoOICu₃S₃(2,2′-bipy)₂] in DMF solution was measured by using a Z-scan technique with 15 ns and 532 nm laser pulses. The cluster has large third-order NLO absorption and the third-order NLO refraction, its ₂ and n₂ values were calculated as 6.2×10⁻¹⁰ and −3.8×10⁻¹⁷ m² W⁻¹ in a 3.7×10⁻⁴ M DMF solution.