Preparation of carbon nanotubes-incorporated polymeric microspheres for electrorheological fluids

Electrically conducting polymeric microspheres having an average diameter of 92 μm were prepared from composites of multiwalled carbon nanotubes (MWCNTs) and suspension-polymerized poly(vinyl chloride) (PVC) particles. Cetyl trimethylammonium bromide and sodium dodecylbenzene sulfonate were selected as the surfactants to stably disperse the MWCNTs in water. Strong adhesion of MWCNTs on the surfaces of the PVC microspheres was observed from the images obtained by field emission scanning electron microscopy. The amount of MWCNTs adsorbed on the microspheres was approximately 2 wt.%, determined by thermogravimetric analysis. The electrical conductivity of these composite-microspheres was remarkably increased upto 1.5 × 10⁻⁴ S/cm compared with that of the pure PVC microspheres (less than 10⁻¹⁴ S/cm), because of the electrically conducting MWCNTs on their surfaces. These microspheres also showed an electrorheological (ER) effect under an electric field (1.8 kV/mm) owing to the interfacial polarization of the MWCNTs-adsorbed microspheres, when they were dispersed in silicone oil (20 wt.%). The MWCNT-adsorbed PVC microspheres formed linear structures by electric force; i.e. the individual microspheres were connected to neighboring microspheres.     

Flame-Retarding and Mechanical Properties of Flexible Polyvinyl Chloride with Surface-Treated Lamellar Magnesium Hydroxide

The effects of hydrophobic magnesium hydroxide (Mg(OH)₂) particles, prepared by a surface modification method with oleic acid, on the flame-retarding and mechanical properties of polyvinyl chloride (PVC) were investigated. Comparison between the use of modified and unmodified Mg(OH)₂ in the preparation of PVC composites showed that the former could provide excellent optical and flame-retarding properties. The dispersion of the modified Mg(OH)₂ particles in the PVC matrix was investigated through scanning electron microscopy. Compared with a composite containing unmodified Mg(OH)₂, the rheological and impact strength properties of that containing the modified Mg(OH)₂ filler were found to be significantly improved. These improvements were mostly attributed to the better dispersion of the modified Mg(OH)₂ particles and the strong adhesion between the filler and matrix.     

Direct writing of conductive silver micropatterns on flexible polyimide film by laser-induced pyrolysis of silver nanoparticle-dispersed film

This article describes fabrication of Ag micropatterns on a flexible polyimide (PI) film by laser direct writing using an Ag nanoparticle-dispersed film as a precursor. Ag micropatterns are characterized by optical microscopy, atomic force microscopy (AFM), field emission scanning electron microscopy (FE-SEM), surface profilometry, and resistivity measurements. The line width of Ag micropatterns can be effectively controlled by altering the experimental parameters of laser direct writing especially laser intensity, objective lens, and laser beam scanning speed etc. Using an objective lens of 100× and laser intensity of 170.50 kW/cm², Ag micropatterns with a line width of about 6 μm have been achieved. The Ag micropatterns show strong adhesion to polyimide surface as evaluated by Scotch-tape test. The resistivity of the Ag micropatterns is determined to be 4.1 × 10⁻⁶ Ω cm using two-point probe method. This value is comparable with the resistivity of bulk Ag (1.6 × 10⁻⁶ Ω cm).     

Effect of Surface Structure of Nano-CaCO3 Particles on Mechanical and Rheological Properties of PVC Composites

To study the effect of different surface structures on resultant mechanical and rheological properties, nano-CaCO₃ particles were treated with isopropyl tri-stearyl titanate (H928), isopropyl tri-(dodecylbenz-enesulfonyl) titanate (JN198), and isopropyl tri-(dioctylpyrophosphato) titanate (JN114). Scanning electron microscopy (SEM) and dynamic mechanic analysis (DMA), carried out to characterize the effective interfacial interaction between the nano-CaCO₃ particles and a poly(vinyl chloride) (PVC) matrix, indicated that JN114 treated nano-CaCO₃ particles had the strongest interfacial interaction with a PVC matrix, while H928 treated nano-CaCO₃ had the weakest. The rheological and mechanical properties of PVC/nano-CaCO₃ composites were investigated as a function of surface structure and filler volume fraction. The tensile yield stress and elongation at break decreased with the increasing of calcium carbonate content while tensile modulus increased. PVC filled with JN114 treated nano-CaCO₃ had the highest tensile modulus and tensile yield stress, while those filled with H928 treated nano-CaCO₃ had the highest elongation at break at the same filler content. The impact strength of PVC/nano-CaCO₃ composites increased with the increasing of CaCO₃ content, and PVC composites filled with JN198 treated nano-CaCO₃ particle had a higher impact strength than those with JN114 or H928 treated, with the value reaching 23.9 ± 0.7 kJ/m² at 11 vol% CaCO₃, four times as high as that of pure PVC. Rheological properties indicated that a suitable interfacial interaction and a good dispersion of inorganic filler in a PVC matrix could reduce the viscosity of PVC/nano-CaCO₃ composites. The interfacial interaction was quantitatively characterized by semiempirical parameters calculated from the tensile strength of PVC/nano-CaCO₃ composites to confirm the results from the SEM and DMA experiments.     

Effect of flexibility of grafted polymer on the morphology and property of nanosilica/PVC composites

In this study, poly(methyl methacrylate)-grafted-nanosilica (PMMA-g-silica) and a copolymer of styrene (St), n-butyl acrylate (BA) and acrylic acid (AA)-grafted-nanosilica (PSBA-g-silica) hybrid nanoparticles were prepared by using a heterophase polymerization technique in an aqueous system. The grafted polymers made up approximately 50 wt.% of the resulted hybrid nanoparticles which showed a spherical and well-dispersed morphology. The silica hybrid nanoparticles were subsequently used as fillers in a poly(vinyl chloride) (PVC) matrix to fabricate PVC nanocomposite. Morphology study of PVC nanocomposites revealed that both PMMA- and PSBA-grafted-silica had an adhesive interface between the silica and PVC. The tensile strength and elongation to break were found to be improved significantly in comparison with that of untreated nanosilica/PVC composites. Finally our results clearly demonstrated that the properties (e.g. chain flexibility, composition) of the grafted polymer in the hybrid nanoparticles could significantly affect the dispersion behavior of hybrid nanoparticles in PVC matrix, dynamic mechanical thermal properties and mechanical properties of the resulted PVC composites.     

Dielectric and impedance studies of DBSA doped polyaniline/PVC composites

Polyaniline (PANI) was doped with dodecylbenzene sulfonic acid (DBSA) and then mixed with PVC by solution blending method to prepare DBSA doped PANI (PAND)/PVC composites. FTIR spectroscopy indicates the strong dipole–dipole interaction between the individual components of the composites. The ac electrical properties of the synthesized composites were investigated by complex impedance spectroscopy in the frequency range of 0.5–10⁶ Hz at room temperature. Both dielectric loss factor and permittivity increase with the decrease of frequency exhibiting strong interfacial polarization at low frequency. Addition of PAND in PVC reduces the charge trapping centers by increasing the number of conducting channels participating in the relaxation process; hence an increase in conductivity is observed.     

Ultrasound-assisted surface treatment of ZrO2 with BSA and incorporating in PVC to improve the properties of the obtained nanocomposites: Fabrication and characterization

This paper describes the preparation of poly(vinyl chloride) (PVC) nanocomposites (NCs) reinforced with modified zirconia (ZrO₂) nanoparticles (NPs). The ZrO₂ NPs were defined as efficient filler for PVC NCs. For achieving the best dispersion and improvement of properties, the surface of ZrO₂ NPs was modified by Bovine Serum Albumin (BSA). Carboxylic acids and amines are important functional groups of BSA which handle the grafting BSA on the surface of ZrO₂ NPs. The PVC/ZrO₂-BSA NCs were fabricated by incorporation of various amounts of the ZrO₂-BSA NPs (3, 6 and 9 wt%) into PVC matrix. All the above processes were accomplished by ultrasonication as a green and environmentally-friendly method. Also, the magnetic and mechanical stirrer was used for the preparation of samples but the results are not suitable and the aggregation was observed which indicated the use of ultrasonic irradiation is the best method for the preparation of NC. The products were characterized by Fourier transform infrared spectroscopy, Transmission electron microscopy, Field emission scanning electron microscopy, X-ray diffraction, Thermogravimetric analysis, Ultraviolet–visible spectroscopy, photoluminescence spectroscopy, energy dispersive X-ray spectroscopy, wettability, and mechanical tests. The achieved PVC/ZrO₂-BSA NCs showed high thermal stability, good mechanical, optical and wettability properties compared to the pure PVC. In addition, among the obtained NCs, the PVC/ZrO₂-BSA NC 6 wt% showed the best improvement.     

Influence of the electrical field applied during thermal cycling on the conductivity of LLDPE/CNT composites

The effect of the electrical field on the conductivity of linear low-density polyethylene/carbon nanotubes/ (LLDPE/CNT) composites during temperature cycling has been investigated. Under applied voltage a positive resistivity temperature coefficient was observed during heating already at low (2–3 wt%) CNT content, followed by a large negative temperature coefficient during cooling whose value depends on the applied voltage. The resistivity values after thermal cycling were markedly lower, while they slightly increased in the absence of an electrical field. The effects of thermal cycling on structural and physical properties of the composites have been evaluated by X-ray diffraction and differential scanning calorimetry.     

Effect of ion beam irradiation on palladium (II) acetyl acetonate dispersed in polymer matrix

Composites, containing different concentrations of palladium (II) acetylacetonate in polymethyl methacrylate (PMMA) matrix were prepared by vigorous mixing. PMMA was prepared by solution polymerization technique. The composites were irradiated with a 120 MeV Ni¹⁰⁺ beam at two different fluences of 1×10¹¹ and 5×10¹² ions/cm² to study ion-induced effects on their dielectric, structural properties and surface morphology. AC electrical properties of these samples were studied in the frequency range 100 Hz to 10 MHz. The dielectric permittivity/loss shows frequency dependent behavior and it obeys the universal law of dielectric (i.e. ?α f ^n?1) for pristine and irradiated samples at high frequency. The crystalline size and crystallinity of the composites were studied by X-ray diffraction analysis. Decrease in peak intensity after irradiation signifies the amorphization which is also responsible for decrease in T _g as obtained by means of differential scanning calorimetry measurement. Fourier transform infrared spectra also support this result. Surface roughness increases upon irradiation as observed from scanning electron microscopy.     

Measurement of surface resistivity and surface conductivity of anodised aluminium by optical interferometry techniques

Optical interferometry techniques were used for the first time to measure the surface resistivity and surface conductivity of anodised aluminium samples in aqueous solution, without any physical contact. The anodization process (oxidation) of the aluminium samples was carried out in different sulphuric acid solutions (1.0–2.5% H₂SO₄), by the technique of electrochemical impedance spectroscopy (EIS), at room temperature. In the mean time, the real-time holographic interferometric was carried out to measure the thickness of anodised (oxide) film of the aluminium samples during the anodization process. Then, the alternating current (AC) impedance (resistance) of the anodised aluminium samples was determined by the technique of electrochemical impedance spectroscopy (EIS) in different sulphuric acid solutions (1.0–2.5% H₂SO₄) at room temperature. In addition, a mathematical model was derived in order to correlate between the AC impedance (resistance) and to the surface (orthogonal) displacement of the samples in solutions. In other words, a proportionality constant (surface resistivity or surface conductivity=1/surface resistivity) between the determined AC impedance (by EIS technique) and the orthogonal displacement (by the optical interferometry techniques) was obtained. Consequently the surface resistivity (ρ) and surface conductivity (σ) of the aluminium samples in solutions were obtained. Also, electrical resistivity values (ρ) from other source were used for comparison sake with the calculated values of this investigation. This study revealed that the measured values of the resistivity for the anodised aluminium samples were 2.8×10⁹, 7×10¹², 2.5×10¹³, and 1.4×10¹²  Ω cm in 1.0%, 1.5%, 2.0%, and 2.5% H₂SO₄ solutions, respectively. In fact, the determined value range of the resistivity is in a good agreement with the one found in literature for the aluminium oxide, 85% Al₂O₃ (5×10¹⁰ Ω cm in air at temperature 30 °C), 96% Al₂O₃ (1×10¹⁴  Ω cm in air at temperature 30 °C), and 99.7% Al₂O₃ (>1×10¹⁴ Ω cm in air at temperature 30 °C).     

Formation of Polyvinyl Alcohol film with graphene nanoplatelets and carbon black for electrostatic discharge protective packaging

This research investigated the synergic effect of graphene nanoplatelets (GNPs) and carbon black (CB) as a blended conductive filler for polymer film used as electrostatic discharge (ESD) packaging materials. Various weight ratios of GNPs/CB and combined filler concentrations were mixed and processed into Polyvinyl Alcohol (PVOH) based film. The surface resistivity and volume resistivity of the resulting film was measured under three different humidity environments. The study found that the composite with GNPs/CB ratios of 10:90 and 30:70 resulted in a sharp drop in surface resistivity by 5–8 orders of magnitude at the filler loading 8-10 wt%. The volume resistivity of the resulting film exhibited steady and consistent ranges within 10⁸–10¹² Ω cm across all loadings. The difference in conductivity between surface and volume made the film possible to be used in protecting equipment against electrostatic discharges inside of a package. The high loading of GNPs in hybrid GNPs/CB had no effect on enhancing both surface and volume conductivity of the composite film.     

Preparation and ablation properties of ZrC-SiC coating for carbon/carbon composites by solid phase infiltration

A novel ZrC-SiC coating was prepared on carbon/carbon (C/C) composites surface by solid phase infiltration and the ablation properties of the ZrC-SiC coated C/C composites under oxyacetylene flame were studied. The results show that the coating prepared on the condition of optimum process parameters exhibits dense surface and outstanding anti-ablation ability. After ablation for 20 s, the mass ablation rates of the coated C/C composites can be lowered to 2.36 × 10⁻³ g/s, 37.1% reduction compared with uncoated C/C composites. The oxide layer composed of ZrO₂ and SiO₂ acts as oxygen diffusion barrier and the evaporation of ZrO₂ and SiO₂ absorbs a great amount of heat from the flame and reduces the erosive attack on the coating.     

Electromagnetic and mechanical properties of Fe3O4-coated amorphous carbon nanotube/polyvinyl chloride composites

Electromagnetic wave absorbing properties of absorbing composites depend on the dielectric and magnetic loss generally. In this paper, using Fe₃O₄-coated amorphous carbon nanotubes (ACNTs-Fe₃O₄) fabricated using a chemical synthesis–hydrothermal treatment method as an absorber and polyvinyl chloride (PVC) as a matrix, electromagnetic and mechanical properties of ACNT-Fe₃O₄/PVC composite were investigated. The results showed that the dielectric and magnetic losses of ACNT-Fe₃O₄/PVC composite were significantly enhanced in 8.2–12.4 GHz compared to ACNT/PVC composite, which improved absorbing properties, while slightly changing the mechanical properties.     

Preparation of PVOH coatings with graphene nanoplatelets for electrostatic discharge protective packaging

This study investigated the use of graphene nanoplatelets (GNP) as a conductive filler for electrostatic discharge (ESD) protective packaging. Various weight concentrations of GNP were mixed and sonicated with polyvinyl alcohol (PVOH). The resulting polymer solution was applied as a coating to corrugated board in order to form an ESD packaging. Surface resistivity, mechanical strength and coating adhesion were then measured. The study found that the electrical percolation threshold of the PVOH/GNP coating is 9–13wt% GNP. GNP incorporated PVOH coatings with surface resistivity of 10³–10⁸ Ω/sq. generally meet all of ESD packaging requirements. The humidity strongly affects the surface resistivity of the coatings below the percolation threshold, but the change of the surface resistivity with humidity is less significant above the percolation threshold.     

An influence of deposition temperature on structural,optical and electrical properties of sprayed ZnO thin films of identical thickness

Nanocrystalline ZnO thin films were deposited at different temperatures (T_s = 325 °C–500 °C) by intermittent spray pyrolysis technique. The thickness (300 ± 10 nm) independent effect of T_s on physical properties was explored. X-Ray diffraction analysis revealed the growth of wurtzite type polycrystalline ZnO films with dominant c-axis orientation along [002] direction. The crystallite size increased (31 nm–60 nm) and optical band-gap energy decreased (3.272 eV–3.242 eV) due to rise in T_s. Scanning electron microscopic analysis of films deposited at 450 °C confirmed uniform growth of vertically aligned ZnO nanorods. The films deposited at higher T_s demonstrated increased hydrophobic behavior. These films exhibited high transmittance (>91%), low dark resistivity (～10^?2 Ω-cm), superior figure of merit (～10^?3 Ω^?1) and low sheet resistance (～10² Ω/□). The charge carrier concentration (η -/cm³) and mobility (μ – cm²V^?1s^?1) are primarily governed by crystallinity, grain boundary passivation and oxygen desorption effects.     

Al-doped zinc oxide films grown by successive chemical solution deposition

Films of ZnO were grown and doped by the successive chemical solution deposition technique from a zincate solution containing aluminum (Al/Zn molar ratio in the range 2–10%). To our knowledge, this is the first report of its kind. A post-deposition heat treatment in argon (500 °C, 20 min) was performed for the activation of incorporated Al donors. Films were characterized by using scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, optical transmittance, photoluminescence and Hall-effect measurement. Films with a resistivity 0.2 Ω cm, carrier concentration 1.2×10¹⁸ cm^-3 and mobility 26 cm²/V s can be grown from a solution with Al/Zn = 10%. Further reduction in resistivity is plausible by using more heavily doped solutions and by the optimization of annealing parameters. Although the doping process does not change the films’ structure and surface morphology, it slightly lowers the optical transparency in the visible region and blue shifts the room-temperature photoluminescence peak to 378 nm. PACS  81.16.Be; 73.61.Ga; 78.55.Et; 79.60.-i; 68.55.Jk     

Thermoelectric properties and electronic structure of Te-doped CoSb3 compounds

Co₄Sb_12−xTe_x compounds were prepared by mechanical alloying combined with cold isostatic pressing, and the effects of Te doping on the thermoelectric properties were studied. The electronic structure of Te-doped and undoped CoSb₃ compounds has been calculated using the first-principles plane-wave pseudo-potential based on density functional theory. The experimental and calculated results show that the value of the solution limit x of Te in Co₄Sb_12−xTe_x compounds is between 0.5 and 0.7. The Fermi surface of CoSb₃ is located between the conduction band and the valence band, and its electrical resistivity decreases with increasing temperature. The density of states is mainly composed of Co 3d and Sb 5p electrons for intrinsic CoSb₃.The Fermi surface of Te-doped compounds moves to the conduction band and its electrical resistivity increases with increasing temperature, exhibiting n-type degenerated semiconductor character. Under the conditions of the experiment, the maximum value 2.67 mW/m K² of the power factor for Co₄Sb_11.7Te_0.3 is obtained at 600 K; this is about 14 times higher than that of CoSb₃.     

Optoelectronic properties of Cu1−xPtxFeO2 (0 ≤ x ≤ 0.05) delafossite for p-type transparent conducting oxide

The samples of Cu_1−xPt_xFeO₂ (0 ≤ x ≤ 0.05) delafossite have been synthesized by solid-state reaction method to investigate their optical and electrical properties. The properties of electrical resistivity and Seebeck coefficient were measured in the high temperature ranging from 300 to 960 K, and the Hall effect and the optical properties were measured at room temperature. The obtained results of Seebeck showed the samples are p-type conductor. The optical properties at room temperature exhibited the samples are transparent visible light material with optical direct gap 3.45 eV. The low electrical resistivity, hole mobility and carrier density at room temperature displayed value ranging from 0.29 to 0.08 Ω cm, 1.8 to 8.6 cm²/V s and 1.56 × 10¹⁸ to 4.04 × 10¹⁹ cm⁻³, respectively. The temperature range for transparent visible light is below 820 K because the direct energy gap contains value above 3.1 eV. Consequently, the Cu_1−xPt_xFeO₂ delafossite enhance performance for materials of p-type transparent conducting oxide (TCO) with low electrical resistivity.     

Influence of carbon nanofibers on electrochemical properties of carbon nanofibers/glass fibers composites

Conducting glass fiber fabrics (GFs) with double-scale roughness were fabricated by growing carbon nanofibers (CNFs) on its surfaces. The homogeneous growth of CNFs was achieved by the decomposition of C₂H₂ on glass fibers surfaces coated with Fe-doped mesoporous silica films at different C₂H₂ flow rates. The chemical composition and surface structure of the GFs before and after CNFs growth were examined by electron dispersive X-ray spectrometry (EDX), N₂ full isotherms, and scanning electron microscopy (SEM). The electrical properties of the GFs were examined using a four-probe volume resistivity tester. The CNFs with a mean diameter of 50 nm grew uniformly and densely on the glass fiber surfaces. The CNFs/GFs fabrics surface exhibited excellent electrochemical properties due to the CNFs. The specific capacitance of the GFs ranged from 0.2 to 4 F/g at 1 A/g in a 1 M H₂SO₄ aqueous solution.     

Structural,optical and electrical properties of tin oxide thin films by electrostatic spray deposition

Tin oxide (SnO₂) thin films were deposited by electrostatic spray deposition (ESD). The structural, optical and electrical properties of the films for different solvents were studied. The morphology of the deposited thin films was investigated by scanning electron microscopy. The optical transmission spectra of the films showed 66–75% transmittance in the visible region of spectrum. The electrical resistivity of thin films deposited using the different solvents ranged 1.08 × 10^?3–1.34 × 10^?3 Ω-cm. Overall, EG and PG were good solvents for depositing SnO₂ thin films by the ESD technique with stable cone jet.