Preparation and characterization of nano-ZnO flakes prepared by reactive ion exchange method

Nano-ZnO flakes were synthesized by calcination of the precursor of Zn(OH)₂ obtained via the reactive ion exchange method between an ion exchange resin and ZnSO₄ solution at room temperature. Scanning electron microscopy, X-ray diffraction, energy dispersive X-ray spectroscope, UV-Vis diffuse reflection spectrum and Na₂EDTA titration were used to characterize the structure features and chemical compositions of the as-prepared ZnO. The results show that the as-prepared ZnO flakes have uniform structure and high purity. Heat capacities in the temperature range of 83 to 396 K were measured. The measured heat capacities values were compared with those of coarse crystal powders and the difference between this two heat capacity curves was analyzed.     

Comparison of chromium speciation by CZE and ion exchange followed by AAS

The hydrogen chromate anion (HCrO4-), which is the predominant species in acidic solutions and solutions with low chromium concentration, was determined by capillary zone electrophoresis (CZE) using UV detection on-column at 200 nm. A fused-silica capillary (55 cm x 50 microm i.d.) was employed with a high negative voltage of 20 kV. Total chromium was determined after reduction by H2O2 and its complexation by EDTA. The use of H2O2 as reducing agent is advantageous, as it does not increase the conductivity of the solution. Detection limits achieved (for 200 s injection time) were 30 and 8 microg/L for Cr(VI) and Cr(III), respectively. The CZE results obtained for Cr(III) and Cr(VI) were compared with those obtained by ion exchange with subsequent AAS.     

Comparison of chromium speciation by CZE and ion exchange followed by AAS

The hydrogen chromate anion (HCrO₄ ^–), which is the predominant species in acidic solutions and solutions with low chromium concentration, was determined by capillary zone electrophoresis (CZE) using UV detection on-column at 200 nm. A fused-silica capillary (55 cm × 50 μm i.d.) was employed with a high negative voltage of 20 kV. Total chromium was determined after reduction by H₂O₂ and its complexation by EDTA. The use of H₂O₂ as reducing agent is advantageous, as it does not increase the conductivity of the solution. Detection limits achieved (for 200 s injection time) were 30 and 8 μg/L for Cr(VI) and Cr(III), respectively. The CZE results obtained for Cr(III) and Cr(VI) were compared with those obtained by ion exchange with subsequent AAS.     

The separation of rhodium and iridium by ion flotation

Mixtures of iridium(IV) and rhodium(III) as IrCl^2-₆ and RhCl^3-₆ are separated by ion flotation. The iridium(IV) is selectively floated from aqueous solutions of pH 2 and 0.05% Ce(IV) with either hexadecyltripropylammonium bromide (HTPAB) or hexadecyltributylammonium bromide (HTBAB). The rhodium(III) does not float under the same conditions. The floated iridium sublate is collected in n-butyl acetate without contamination by the unfloated rhodium. Data are presented also for the separation and recovery of the Ir(IV) and Rh(III) with the above surfactants, hexadecyltrimethyl-ammonium bromide (HTMAB) and hexadecyltriethylammonium bromide (HTEAB) from solutions of various sodium chloride and hydrochloric acid concentrations. The use of solvent sublation for recovering the floated iridium is examined. The separation is fast, practical, simple and does not require expensive reagents or apparatus. For these reasons, the separation of iridium and rhodium by ion flotation offers advantages over previous methods.     

机械力化学反应法制备纳米金红石型二氧化钛的研究

以Ti (C4H9O)4 和 C2H2O4·2H2O 为原料在室温下利用机械力化学反应法制备前驱体,利用热重-微商热重法(TG-DTG)决定前驱体的分解温度,通过在特定温度下对前驱体进行热分解得到TiO2.利用XRD,SEM,ZETA 电位粒度分析仪以及紫外光谱仪对所得样品物相,形貌,粒度和光学性能进行分析和表征.结果显示所得粉体微观形貌为球形,其直径(＞ 95%)小于60nm,粒径较小的粉体对紫外线UVA波段的吸收效果较好.     

Comparison of cation adsorption by isostructural rutile and cassiterite

Macroscopic net proton charging curves for powdered rutile and cassiterite specimens with the (110) crystal face predominant, as a function of pH in RbCl and NaCl solutions, trace SrCl(2) in NaCl, and trace ZnCl(2) in NaCl and Na Triflate solutions, are compared to corresponding molecular-level information obtained from static DFT optimizations and classical MD simulations, as well as synchrotron X-ray methods. The similarities and differences in the macroscopic charging behavior of rutile and cassiterite largely reflect the cation binding modes observed at the molecular level. Cation adsorption is primarily inner-sphere on both isostructural (110) surfaces, despite predictions that outer-sphere binding should predominate on low bulk dielectric constant oxides such as cassiterite (ε(bulk) ≈ 11). Inner-sphere adsorption is also significant for Rb(+) and Na(+) on neutral surfaces, whereas Cl(-) binding is predominately outer-sphere. As negative surface charge increases, relatively more Rb(+), Na(+), and especially Sr(2+) are bound in highly desolvated tetradentate fashion on the rutile (110) surface, largely accounting for enhanced negative charge development relative to cassiterite. Charging curves in the presence of Zn(2+) are very steep but similar for both oxides, reflective of Zn(2+) hydrolysis (and accompanying proton release) during the adsorption process, and the similar binding modes for ZnOH(+) on both surfaces. These results suggest that differences in cation adsorption between high and low bulk dielectric constant oxides are more subtly related to the relative degree of cation desolvation accompanying inner-sphere binding (i.e., more tetradentate binding on rutile), rather than distinct inner- and outer-sphere adsorption modes. Cation desolvation may be favored at the rutile (110) surface in part because inner-sphere water molecules are bound further from and less tightly than on the cassiterite (110) surface. Hence, their removal upon inner-sphere cation binding is relatively more favorable.     

Dispersion behaviors of molybdena on titania (rutile and/or anatase)

Raman and FT-IR spectra were employed to investigate the dispersion of molybdena on mixed TiO2 (rutile and anatase, signed as R and A) with different BET surface ratios of rutile/TiO2(R + A). The results showed that (1) molybdena would preferentially disperse on the rutile surface in mixed TiO2; (2) for MoO3/rutile with low molybdena loading (e.g., 0.20 mmol/100 m2 rutile), a dispersed molybdena species existed on the rutile surface in an isolated tetrahedral coordination environment, while for MoO3/rutile with high molybdena loading (e.g. 0.82 mmol/100 m2 rutile), a polymeric molybdena species could be detected on the rutile surface; (3) for the MoO3/anatase sample, a dispersed molybdena species existed on the anatase surface in a polymeric coordination environment; and (4) the formation of the Bronsted acid site on the surface of rutile and anatase should be related to the polymeric molybdena species. All these results have been discussed via the interaction between OH groups of molybdena and OH groups of rutile and anatase, and it seems reasonable to suggest that, for the lower molybdena loading, the different states of the dispersed molybdena species should result from the different dehydration orders of OH groups of the molybdena and surface OH groups of rutile and anatase.     

Characterization and catalytic behavior of silica-supported copper catalysts prepared by impregnation and ion-exchange methods

Two kinds of Cu/SiO₂ catalysts were prepared by impregnation (IM) and ion-exchange (IE) methods, and tested in dehydrogenation of 2-butanol to methyl-ethyl-ketone. Some kinds of Cu²⁺ on the IE catalyst could not be reduced during the reaction, and it produced the butene. The copper oxide over the IM catalyst could be reduced during the reaction, and showed stable dehydrogenation activity for 2-butanol.     

Selective separation of gold from iron ore samples using ion exchange resin

Gold in iron ore samples is separated from iron (major matrix cation), antimony and vanadium using anion exchange resin in (0.2 M) HBr, potassium peroxodisulfate and acetone:water:nitric acid media. The exchangeable anion Cl⁻ of the ion exchanger Dowex 1X 4 is replaced by Br⁻ using (6 M) HBr solution. Certified reference material DGP-M1, spiked ferric magnetic oxide, gold radioactive tracer ¹⁹⁸Au and gold standard solutions are used to study the adsorption efficiency and the yield recovery of tetrabromoaurate AuBr₄⁻ from the resin. Ten eluents have been tried to elute gold from the column, and it has been found that a 10 ml potassium peroxodisulfate and 240 ml acetone:water:nitric acid [125:5:5] solution fulfills the objective. The set up of the separation procedure allows quantitative adsorption of gold by the resin, while the major matrix cation (Fe) and others (Cd, Ag, Cu, V, Sb, Ti) have been passed through the column with the feeding solution (0.2 M) HBr. The resin selectivity coefficient (K) of separating Au from Fe has been found to be K_Fe^Au≈6.4×10¹¹. The eluted Au is treated with K₂S₂O₈ and H₂O₂ for spectrophotometric determination as rhodamine-B complex at 555.6 nm. The linearity, detection limit, precision, and accuracy of the determination method have been found to be up to 2.0 μg g⁻¹, 0.018 μg g⁻¹, 0.009 μg g⁻¹ and 3%, respectively.     

Separation of uranium from iron in ground water samples using ion exchange resins

Uranium determination in environmental samples is faced with problems due to presence of iron and other major elements. Iron is also used many a times for pre-concentration of uranium and actinides. Separation of milligram quantity of Fe from microgram quantity of uranium becomes essential during the estimation step. A simple two step procedure has been standardized for separating uranium and iron using anion exchange in 0.025 M H₂SO₄. Quantitative recovery of uranium was obtained as well as good separation from iron. This method was applied for estimation of uranium in water samples.     

Comparative studies of gold catalysts prepared via solvated metal atom impregnation and conventional impregnation: characterization and low-temperature co oxidation

Supported Au catalysts for low-temperature CO oxidation were prepared by solvated metal atom impregnation (SMAI) and conventional impregnation (CI). X-ray photoelectron spectroscopy investigations indicated that gold in all the samples was in the metallic state. TEM and XRD measurements showed that the mean diameter of Au particles prepared by SMAI was smaller than that of those prepared by CI with the same gold content. Catalytic tests showed that SMAI catalysts had higher CO oxidation activity than CI catalysts with the same compositions. Both SMAI and CI Au/TiO₂catalysts exhibited high activities in low temperature CO oxidation. Full CO conversion was obtained at 323 K for 3.1 wt.% Au/TiO₂ (SMAI) catalyst, which displayed higher activity than the 3.1 wt.% Au/D-72(SMAI) and 3.1 wt.% Au/TiO₂(CI). Although the sizes of gold particles prepared by the same method and supported on both TiO₂ and resin were comparable, the Au/TiO₂ catalysts showed significantly higher activities than the Au/resin catalysts with the same Au contents under the same reaction conditions. These results prove that not only the gold particle size, but also the support plays a key role in CO oxidation. This revised version was published online in June 2006 with corrections to the Cover Date.     

Determination of mercury in agroindustrial samples by flow-injection cold vapor atomic absorption spectrometry using ion exchange and reductive elution

A flow-injection system with a Chelite-S(R) cationic resin packed minicolumn is proposed for the determination of trace levels of mercury in agroindustrial samples by cold vapor atomic absorption spectrometry. Improved sensitivity and selectivity are attained since mercuric ions are on-line concentrated whereas other potential interferents are discarded. With on-line reductive elution procedure, concentrated hydrochloric acid could be replaced by 10% w/v SnCl(2), in 6 M HCl as eluent. The reversed-intermittent stream either carries the atomic mercury to the flow cell in the forward direction or removes the residue from reactor/gas-liquid separator to a discarding flask in the opposite direction. Concentration and volume of reagent, acidity, flow rates, commutation times and potential interfering species were investigated. For 120 s preconcentration time, the proposed system handles about 25 samples h(-1) (50.0-500 ng l(-1)), consuming about 10 ml sample and 5 mg SnCl(2) per determination. The detection limit is 0.8 ng l(-1) and the relative standard deviation (RSD) (n=12) of a 76.7 ng l(-1) sample is about 5%. Results are in agreement with certified value of standard materials at 95% confidence level and good recoveries (97-128%) of spiked samples were found.     

Studies on ion exchange equilibria and kinetics

¹⁶⁰Tb was used as radiotracer and the equilibria and kinetics of cation exchange with zeolite-Y were studied. The ion exchange isothems and the Kielland plots at 298 and 303 K were obtained. It was found that the ion exchange rate is controlled by particle diffusion. The integral interdiffusion coefficients for the direct and reverse exchanges at 298 K and 303 K were calculated. In addition, the isotopic ion exchange was studied too.     

Studies on ion exchange equilibria and kinetics

The kinetics and equilibria of cation exchange HR+Na⁺=NaR+H⁺ with 001×7 strong acidic resin have been studied. The isotherm for this reaction has been determined, and the rational equilibrium constant, Ka, calculated. It is found experimentally that at low concentration, the reverse exchange RNa/H⁺ is faster than the forward exchange; on the contrary, at high concentration, the forward exchange is faster than the reverse exchange. The integral particle interdiffusion coefficients have been calculated and the film interdiffusion coefficients estimated.     

Radiochemical separation of thorium by isotope ion exchange

The aim of the present work is to obtain the separation of²³³Th from the radioisotopes formed in the irradiation of Mn, U, Ba, Cs, Co and the lanthanide elements with thermal neutrons, because they may interfere in the neutron activation analysis of Th, when the activity of²³³Th is used. The experiments were performed with the resin Bio-Rad AG 50W X-4 and X-8 (100–200 mesh) in the thorium form. The separation of²³³Th from the interfering radioisotopes is based on the retention of²³³Th by the resin (isotope exchange) and the elution of the interfering radioisotopes with a dilute solution of Th in 0.5M HCl. Batch experiments were made in order to determine the equilibrium time for the isotopic ion exchange of thorium and also the distribution coefficients of the interfering elements between the solution and the resin. Column experiments were carried out with the purpose of establishing the conditions that allow the maximum isotope exchange of²³³Th and the minimum retention of the interfering radioisotopes in the resin. With this purpose, a statistical interpretation of a four variable experimental design is presented.From a thesis submitted by C. Sepúlveda Munita to the Instituto de Pesquisas Energéticas e Nucleares (CNEN/SP) University of São Paulo, in partial fulfillment of a Doctor of Science's Degree. Work supported by the Brazilian Atomic Energy Commission.     

Comparison of the determination of anions in dissolved organic carbon-loaded water samples by ion chromatography and photometric methods

Dissolved organic carbon (DOC) in water samples can cause strong interferences in photometric detection methods using complexing reactions. Ion chromatography was demonstrated to minimize DOC effects on the determination of anions. Further, it can be used to examine the accuracy of photometric methods by calculating the difference in the ion balance using ion chromatographic values.     

Separation of hydroxy acids by ion exchange chromatography

Factors affecting the Chromatographic separation of hydroxy acids by means of anion exchange resins in the borate form have been studied. With the acids studied the separation factor increases for a decreased borate concentration in the eluant. With complicated mixtures it is recommended to employ stepwise elution with solutions of increasing concentration.     

Rapid radiochemical separation and determination of chlorine,bromine and iodine in water samples using ion exchange

On the basis of tracer experiments, a simple and rapid radiochemical separation method for simultaneous determination of I^–, Br^– and Cl^– in one aliquot of a water sample (only 2–4 ml) has been developed. The method is based on short irradiation of the water sample and separation of the halogens using sequential ion exchange columns filled with Dowex 1×8, 100–200 mesh anionic resin prepared in I^–/I₂, Br^–/Br₂ and Cl^– form. After washing the columns with an appropriate volume of 2% NaCl solution, the resins were transferred to vials and activities of the isolated radionuclides¹²⁸I,⁸²Br and³⁸Cl measured together with standards in a well type or on a coaxial Ge detector connected to a Canberra 90 multichannel analyzer. Besides high chemical yields, from the -spectra of the isolated radionuclides, it is evident that high decontamination fac-The paper was presented at the MTAA-8, Vienna, September 1991.