The effect of soft-segment length and concentration on phase separation in segmented polyurethanes

Three series of polyurethanes, based on three polyols, diphenylmethane diisocyanate (MDI), and three chain extenders were synthesized. Polypropylene glycol (PPG) soft-segment length (MW 1000, 2000, and 3000), soft-segment concentration (30%, 50%, and 70%), and the type of chain extender (ethylene glycol, butane diol, and hexane diol) were varied and their effect on the amount of phase separation studied. Methods for assessing phase separation quantitatively, based on shifts of the glass transition temperature T_g and the enthalpy jump at the glass transition were tested. It was shown that they give incorrect results, especially with PPG 1000 as the soft segment. Dependence of the soft segment T_g on the polyol length was explained by the “network effect.” True phase mixing was found only with PPG 1000 series at low soft-segment concentration, whereas, no clear indication of the phase mixing with PPG 2000 and PPG 3000 based polyurethanes was observed.     

Preparation of Polyamide‐6 Submicrometer‐Sized Spheres by In Situ Polymerization

Polyamide‐6 (PA6) submicron‐sized spheres are prepared by two steps: (1) anionic ring‐opening polymerization of ε‐caprolactam in the presence of poly(ethylene glycol)‐block‐poly‐(propylene glycol)‐block‐poly(ethylene glycol)(PEG‐b‐PPG‐b‐PEG) and (2) separation of PA6 spheres by dissolving PEG‐b‐PPG‐b‐PEG from the prepared blends. The PA6 microspheres obtained are regular spherical, with diameter ranging from 200 nm to 2 μm and narrow size distribution, as confirmed by scanning electron microscopy. By comparison with PA6/PS and PA6/PEG systems, it is denominated that the PEG blocks in PEG‐b‐PPG‐b‐PEG can effectively reduce the surface tension of PA6 droplets and further decrease the diameter of the PA6 microspheres. The PPG block in PEG‐b‐PPG‐b‐PEG can prevent the PA6 droplets coalescing with each other, and isolated spherical particles can be obtained finally. The phase inversion of the PA6/PEG‐b‐PPG‐b‐PEG blends occurs at very low PEG‐b‐PPG‐b‐PEG content; the PEG‐b‐PPG‐b‐PEG phase can be removed by water easily. The whole experiment can be finished in a short time (approximately in half an hour) without using any organic solvents; it is an efficient strategy for the preparation of submicron‐sized PA6 microspheres.

     

Synthesis and non‐isothermal crystallization kinetics of poly(ethylene terephthalate)‐co‐poly(propylene glycol) copolymers

Poly(ethylene terephthalate)‐co‐poly(propylene glycol) (PET‐co‐PPG) copolymers with PPG ratio ranging from 0 to 0.90 mol% were synthesized by the melt copolycondensation. The intrinsic viscosity, structure, non‐isothermal crystallization behavior, nucleation and spherulitic growth of the copolymers were investigated by Ubbelohde viscometer, Proton Nuclear Magnetic Resonance (¹H‐NMR), differential scanning calorimetry, and polarized optical microscopy, respectively. The non‐isothermal crystallization process of the copolymers was analyzed by Avrami, Ozawa, Mo's, Kissinger, and Dobreva methods, respectively. The results showed that the crystallizability of PET was apparently enhanced with incorporating a small amount of PPG, which first rose and then reduced with increasing amount of PPG in the copolymers at a given cooling rate. The crystallization mechanism was a three‐dimensional growth with both instantaneous and sporadic nucleation. Particularly, PET‐co‐PPG containing 0.60 mol% PPG exhibited the highest crystallizability among all the copolymers. Copyright © 2015 John Wiley & Sons, Ltd.     

Sol–gel silica antireflective coating with enhanced abrasion-resistance using polypropylene glycol as porogen

Silica antireflective (AR) coatings with high transmittance and enhanced abrasion-resistance were synthesized by sol–gel process using polypropylene glycol (PPG) as porogen. The effects of molecular weight of PPG and weight ratio of PPG to SiO₂ on the refractive index and abrasion-resistance of the coating were systematically studied and compared with those of polyethylene glycol (PEG). Experimental data showed that the refractive index decreased with increasing the weight ratio to SiO₂ and molecular weight of both PEG and PPG, but PPG was much more effective than PEG. In the case of same molecular weight, PPG modified coating has the higher porosity than PEG modified one. When the weight ratio of PPG to SiO₂ is in a low level, the PPG-containing silica AR coatings exhibit the good abrasion-resistance. PPG is liquid at room temperature and the better solubility than PEG. These effective and economic AR coatings with enhanced abrasion-resistance have potential value in the field of solar thermal collectors.     

Biohybrid nanogels by crosslinking of ovalbumin with reactive star‐PEGs in W/O emulsions

This article reports the synthesis of biohybrid nanogels by crosslinking six‐arm acrylate functionalized star shaped P(EO‐stat‐PO) with the amine groups of various amino acids of a hen egg ovalbumin in W/O emulsion. PEG Poly(ethylene glycol)‐diamines of different molecular weights (368.5 g/mol, 897.1 g/mol, 3000 g/mol, and 6000 g/mol) were used to optimize the crosslinking reactions in aqueous droplets. The increase of molecular weight of the PEG‐diamine led to decrease of the nanogel size due to better stabilization by longer PEG chains. The size of the ovalbumin nanogels was independent of the acrylate‐sP(EO‐stat‐PO):ovalbumin ratio in the reaction mixture. The bicinchoninic acid (BCA) assay proved that the ovalbumin has been effectively crosslinked by reactive prepolymers. From the results of BCA assay, it can also be established that there exists a limiting amount of ovalbumin which can be incorporated into the nanogels. Both Diamine and ovalbumin‐based nanogels exhibit amphoteric behavior and display a positive charge in acidic and a negative charge in basic environment. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Characterization of polyethers using different methods: SFC,LAC and SEC with different detectors,and MALDI-TOF-MS

Polyethylene glycol 300 (PEG 300) and polypropylene glycol 425 (PPG 425) were analyzed using size exclusion chromatography (SEC) in different solvents, normal and reversed phase liquid chromatography (NPLC and RPLC), supercritical fluid chromatography (SFC), and matrix-assisted laserdesorption/ionisation time-of-flight mass spectrometry (MALDI-TOF-MS). In liquid chromatography, different detectors were used: density, refractive index (RI) and evaporative light scattering detector (ELSD).     

Characterization of polyether mixtures using thin-layer chromatography and matrix-assisted laser desorption/ionization mass spectrometry

Thin-layer chromatography (TLC) and matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) were combined to achieve characterization of polyether mixtures. Three polyethers, polyethylene glycol (PEG), polypropylene glycol (PPG) and polytetramethylene glycol (PTMG), or mixtures of these compounds, were studied. One shortcoming of mixture analysis of synthetic polymers using MALDI-MS is that individual polymers in the mixture may display different detection sensitivities. For example, the MALDI mass spectrum of an equimolar mixture of PEG, PPG and PTMG displayed a high intensity of PPG ions, while no PTMG ions were detectable; however, PTMG ions were detected after the mixture had been separated by TLC. This combined TLC and MALDI-MS analysis of a PPG polymer bearing reactive epoxy groups showed that the polymer contained byproducts with different end-groups. These byproducts were identified as chloro-substituted polymers formed during polymer synthesis. Our study shows TLC to be a rapid and low-cost separation technique, and that it can be combined with MALDI-MS to achieve effective analysis of synthetic polymers.     

Liquid–Liquid Equilibrium and Thermodynamic Modeling of Aqueous Two-Phase System Containing Polypropylene Glycol and NaClO<Subscript>4</Subscript> at <Emphasis Type="Italic">T</Emphasis> = (288.15 and 298.15) K

In this work the phase equilibrium of an aqueous two phase system (ATPS) containing polypropylene glycol (PPG, molecular weight = 425 kg·mol^?1) and NaClO₄ was investigated at atmospheric pressure and at 288.15 and 298.15 K. Two phase regions and composition of phases were determined. Our results show that as the temperature increases, the two-phase region expands. Also, the extended UNIQUAC (E-UNIQUAC) equation was used to correlate the equilibrium data. To reduce the number of adjustable parameters, ATPSs composed of PEG and PPG were collected from the literature and simultaneously correlated using the E-UNIQUAC model. Also, the effect of temperature on the liquid–liquid equilibrium (LLE) was considered by using temperature-dependent parameters. In the modeling, two different scenarios were supposed. In the first, polymer and salt were treated as solutes (Case A), while in the second, the pseudo-solvent approach was considered (Case B). The results showed good agreement with experimental data in both cases. The average absolute deviation of the model using Case B was about 0.2% and that for Case A was about 2% in the ATPS composed of PEG. Meanwhile, the reported errors in the ATPS containing PPG for Case A and Case B were almost equal.     

Effects of prepolymer structure in holographic polymer dispersed liquid crystal

Three different types of polyols—poly(ethylene glycol) (PEG), poly(propylene glycol) (PPG), and poly(tetramethylene glycol)—with different molecular weights (M_n) were incorporated into the prepolymer structure, and the effects were examined with regard to the morphology and performance of holographic polymer dispersed liquid crystal. Among them, PEG showing the lowest glass transition temperature (T_g) exhibited the lowest threshold voltage (V_th), lowest operating voltage (V_op), and lowest diffraction efficiency with slow grating formation owing to its high viscosity of prepolymer mixture. The T_g decreased with increasing M_n because of the decreased crosslink density and hydrogen bonding, which reduced the anchoring strength, V_th and V_op. PPG400 gave V_th and V_op of approximately 7 and 24 V, respectively, with a contrast ratio of approximately 12. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Application of New Modified Poly(ethylene Oxide)-Block-Poly(propylene oxide)-Block-Poly(ethylene oxide) Copolymers as Demulsifier for Petroleum Crude Oil Emulsion

Water soluble nonionic amphiphilic block copolymers based on hydrophilic poly(ethylene glycol) (PEG) and hydrophobic poly(propylene glycol) (PPG) were prepared. Poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol) copolymers, PEG-PPG-PEG, were prepared in the normal condition. The chemical composition and molecular weights of the prepared copolymers were determined from ¹H NMR and GPC techniques. The surface properties of the prepared surfactants were determined by measuring the surface tension at different temperatures. The prepared nonionic surfactants were evaluated as demulsifiers for water in crude-oil emulsions that were pronounced at different ratios of crude oil: water at 318 K and 333 K. The experimental results showed that the dehydration rate of the prepared demulsifiers reached 100% based on demulsifier chemical compositions and concentrations.     

Preparation and characterization of thermoresponsive isopropylacrylamide–hydroxyethylmethacrylate copolymer gels

A random copolymer of N-isopropylacrylamide and 2-hydroxyethylmeth-acrylate, poly(NIPAM-co-HEMA), having thermoresponsive character was prepared bya redox copolymerization method. Poly(ethylene glycol), PEG 4000 was included in the copolymerization recipe to increase the thermoresponsivity of copolymeric structure. Poly(NIPAM-co-HEMA) copolymer gels having more elastic character and higher mechanical strength relative to poly(NIPAM) gel could be achieved by the proposed copolymerization procedure. The equilibrium and dynamic response against the temperature were investigated for the gel matrices produced by changing the initial NIPAM/HEMA mol ratio and PEG 4000 concentration in the copolymerization mixture. The effective diffusion coefficient of water within the gel matrix was estimated for either swollen or shrunken states by applying an unsteady-state diffusion model on the dynamic swelling and shrinking behaviors of gel matrix prepared in the cylindrical form. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 527–541, 1998     

Sequencing of specific copolymer oligomers by electron-capture-dissociation mass spectrometry

Although a poly(ethylene/propylene glycol) (PEG/PPG) copolymer mixture is far too complex (approximately 150 oligomeric formulas) for conventional purification, oligomer ion compositions of <1% abundance can be separated by Fourier transform mass spectrometry and dissociated into sequence-specific fragment ions. Using collisionally activated dissociation (CAD) or other conventional energetic methods, we found that misleading rearrangements are common; however, these are negligible with electron capture dissociation (ECD), consistent with its nonergodic mechanism. Despite the lack of reference compounds, ECD of five oligomers ranging from PEG(1)PPG(18) to PEG(9)PPG(15) shows that approximately 80% of their isomers have all PEG units at one end, while CAD gave lower values because of an approximately 21% rearrangement loss of internal monomer units. In contrast to the indicated triblock "PEG/PPG/PEG" sample designation of this commercial surfactant, all of these oligomers are found to consist primarily of diblock PEG/PPG structures, so that their termini differ significantly in hydrophobicity, as expected for a surfactant.     

Effect of PLGA block molecular weight on gelling temperature of PLGA‐PEG‐PLGA thermoresponsive copolymers

Thermoresponsive, biodegradable polymeric hydrogel networks are used widely in medicinal applications. Poly(d ,l ‐lactic acid‐co‐glycolic acid)‐b‐poly(ethylene glycol)‐b‐poly(d ,l ‐lactic acid‐co‐glycolic acid) (PLGA‐PEG‐PLGA) triblock copolymers exhibit a sol–gel transition upon heating. The effect of PLGA block and PEG chain molecular weights (MWs) on the gelling temperature of polymer aqueous solution (20% w/w) is described. All polymer solutions convert into a hard gel within 2 °C of the gelling temperature. The release properties of the gels were displayed using paracetamol as a representative drug. A linear relation is described between the gelling temperature and PLGA block MW. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 35–39     

Application of aqueous mixtures of polypropylene glycol or polyethylene glycol with salts in proteomic analysis

Partitioning of Bovine serum albumin (BSA), β-lactoglobulin (β-LG) and zein as model proteins in aqueous two-phase systems (S) containing polypropylene glycol (PPG425) or polyethylene glycol (PEG 6000) and salts (MgSO₄, (NH₄)₂SO₄, Na₂SO₄) is presented in this paper. The effects of different factors such as tie-line length, salt type and polymer type on the partition coefficient and recovery percent of proteins were analysed. The model proteins were separated by these systems (S) and directly used for gel electrophoresis without separating the target proteins from phase-forming reagents. The results revealed that the S, studied in this work could be used as a novel prefractionation method in proteomic analysis and could separate proteomic proteins in multigroup by one step extraction.     

UV-curable poly(ethylene glycol)–based polyurethane acrylate hydrogel

Poly(ethylene glycol) (PEG) with molecular weight (M_n) of 1000, 2000, 3000, and 4000 g/mol, four types of diisocyanate [hexamethylene diisocyanate (HDI), 4,4′-dicyclohexylmethane diisocyanate (H₁₂MDI), isophorone diisocyanate (IPDI), and toluene diisocyanate (TDI)], two types of comonomers [acrylamide (AAm) and acrylic acid (AAc)] that comprised up to 60% of the total solid were used to prepare UV-curable PEG–based polyurethane (PU) acrylate hydrogel. The gels were evaluated in terms of mechanical properties, water content as a function of immersion time and pH, and X-ray diffraction profiles of dry and swollen films. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2703–2709, 1999     

Solvent extraction of cesium into nitrobenzene by using a synergistic mixture of hydrogen dicarbollylcobaltate and polypropylene glycol PPG 425

Extraction of microamounts of cesium by a nitrobenzene solution of hydrogen dicarbollylcobaltate (H⁺B^?) in the presence of polypropylene glycol PPG 425 (L) has been investigated. The equilibrium data have been explained assuming that the complex species HL⁺ and CsL⁺ (L = PPG 425) are extracted into the organic phase. The values of extraction and stability constants of the cationic complex species in nitrobenzene saturated with water have been determined.     

Efficient Synthesis of Polyethylene Glycol Mono‐Carboxylate via Michael Conjugate Addition

Abstract

Poly(ethylene glycol) (PEG) with one carboxylate group, the very useful precursors for the synthesis of the PEG derived heterobifunctional linkers, are synthesized in high yield in one‐pot via Michael conjugate addition of acrylate esters with PEG and catalyst amount of sodium in THF.     

Synthesis of poly(ethylene glycol)/polypeptide/poly(D,L‐lactide) copolymers and their nanoparticles

Core‐shell structured nanoparticles of poly(ethylene glycol) (PEG)/polypeptide/poly(D ,L ‐lactide) (PLA) copolymers were prepared and their properties were investigated. The copolymers had a poly(L ‐serine) or poly(L ‐phenylalanine) block as a linker between a hydrophilic PEG and a hydrophobic PLA unit. They formed core‐shell structured nanoparticles, where the polypeptide block resided at the interface between a hydrophilic PEG shell and a hydrophobic PLA core. In the synthesis, poly(ethylene glycol)‐b‐poly(L ‐serine) (PEG‐PSER) was prepared by ring opening polymerization of N‐carboxyanhydride of O‐(tert‐butyl)‐L ‐serine and subsequent removal of tert‐butyl groups. Poly(ethylene glycol)‐b‐poly(L ‐phenylalanine) (PEG‐PPA) was obtained by ring opening polymerization of N‐carboxyanhydride of L ‐phenylalanine. Methoxy‐poly(ethylene glycol)‐amine with a MW of 5000 was used as an initiator for both polymerizations. The polymerization of D ,L ‐lactide by initiation with PEG‐PSER and PEG‐PPA produced a comb‐like copolymer, poly(ethylene glycol)‐b‐[poly(L ‐serine)‐g‐poly(D ,L ‐lactide)] (PEG‐PSER‐PLA) and a linear copolymer, poly(ethylene glycol)‐b‐poly(L ‐phenylalanine)‐b‐poly(D ,L ‐lactide) (PEG‐PPA‐PLA), respectively. The nanoparticles obtained from PEG‐PPA‐PLA showed a negative zeta potential value of ?16.6 mV, while those of PEG‐PSER‐PLA exhibited a positive value of about 19.3 mV. In pH 7.0 phosphate buffer solution at 36 °C, the nanoparticles of PEG/polypeptide/PLA copolymers showed much better stability than those of a linear PEG‐PLA copolymer having a comparable molecular weight. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Factors of Influencing the Grafting Ratio of Poly(γ-benzyl-L-glutamate)-graft-Poly (ethylene glycol) Copolymer

Poly(γ-benzyl-L-glutamate)-graft-poly(ethylene glycol) (PBLG-graft-PEG) copolymer was synthesized by the ester exchange reaction of PBLG with PEG. Nuclear magnetic resonance (NMR) spectroscopy and scanning electron microscopy (SEM) were used to characterize the structure of PBLG-graft-PEG copolymer. The effects of reaction temperature, reaction time, and the chain length of PEG on the grafting ratio of PBLG-graft-PEG copolymer were investigated.     

Solvent extraction of some divalent metal cations into nitrobenzene by using a synergistic mixture of strontium dicarbollylcobaltate and hexaethyl calix[6]arene hexaacetate

Extraction of microamounts of cesium by a nitrobenzene solution of hydrogen dicarbollylcobaltate (H⁺B⁻) in the presence of polypropylene glycol PPG 425 (L) has been investigated. The equilibrium data have been explained assuming that the complex species HL⁺ and CsL⁺ (L = PPG 425) are extracted into the organic phase. The values of extraction and stability constants of the cationic complex species in nitrobenzene saturated with water have been determined.