Synthesis and characterization of spinel LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles prepared by high-energy milling and hydrothermal method

Spinel LiMn₂O₄ has been known to be a technologically important, environmental-friendly, and low-cost cathode material used in Li-based rechargeable batteries, and it is also widely available. Nanoparticle spinel LiMn₂O₄ has been synthesized by the top-down, high-energy milling, and hydrothermal methods. SEM images, X-ray diffraction patterns, and neutron high-resolution powder diffraction patterns have confirmed the nanocrystalline nature of the spinel LiMn₂O₄ samples. Raman and Fourier transform infrared (FTIR) measurements show typical absorption and vibration spectra typical for the spinel LiMn₂O₄ showing the formation of various metallic bonds in the sample. The strongest Raman and FTIR signals come from the higher frequency region, with weaker signals appearing in the lower frequency range.     

Evolution of MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript> crystals in Al-Mg-SiO<Subscript>2</Subscript> composites

The present study analyzes the morphological transformations of reaction products i.e., MgO, MgAl₂O₄ occurring during the reaction between SiO₂ and Al-Mg alloy in Al-Mg-SiO₂ composite processed by the liquid metallurgy technique. Different phases of platelet and hexagonal morphologies are detected and their composition analysis by EDS has confirmed them as being transition phases existing between MgO, MgAl₂O₄ and Al₂O₃. This study has also revealed the gradual transformation of (i) MgO needles to octahedral MgAl₂O₄ through Mg-Al-Si-O and Mg-Al-O transition phases having platelet morphologies and (ii) MgAl₂O₄ to Al₂O₃ through hexagonal transition phases on holding of Al-5Mg-SiO₂ and Al-1Mg-SiO₂ composites respectively at 1023K. Fully developed α-Al₂O₃ crystals are not observed under the present experimental conditions, wherein the Mg content is well above the equilibrium Mg content required for the formation of stable Al₂O₃ (<0.05 wt. %). PACS 05.70.Np     

Magnetoreflection of light in CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> magnetostrictive spinel

The reflection and magnetoreflection of natural light within the infrared spectral range is studied in single crystals of CoFe₂O₄ ferrimagnetic ferrite spinel. Correlation between the reflection of light and magnetoelastic characteristics of this spinel is found. It is shown that the most significant magnetic-field-induced changes in the magnetoreflection of the spinel occur near the fundamental absorption edge and within the range of the phonon spectrum.     

Synthesis and microstructure of Co/Ni: MgGa<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles

This report discusses the preparation and microstructure of Co/Ni co-doped MgGa₂O₄ nanoparticles. The nanoparticles with the size of 20–55 nm were synthesized by sol-gel method. The phase and crystallinity were confirmed by X-ray powder diffraction (XRD) pattern. The particle size was estimated according to XRD data and transmission electron microscopy. The electronic structure was studied using X-ray photoelectron spectroscopy (XPS). The XPS studies showed that Ga³⁺ ions possess tetrahedral and octahedral sites of spinel structure and the inverse degree (two times of the fraction of tetrahedral Ga³⁺ ions) has increased with the increase of the doping concentration of Co²⁺ and Ni²⁺ ions. For Co/Ni co-doped MgGa₂O₄, two broad absorption bands of 350~500 and 550~700 nm were observed in the absorption spectra. The broad band at 350~500 nm was assigned to the combination of the absorption of octahedral Co²⁺ and Ni²⁺ ions, whereas the absorption band at 550~700 nm is mainly due to tetrahedrally coordinated Co²⁺ ions and octahedrally coordinated Ni²⁺ ions.     

Anisotropy of nonlinear absorption in Co<Superscript>2+</Superscript>:MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript> crystal

Anisotropy of the nonlinear absorption of Co²⁺ ions in MgAl₂O₄ single crystal at the wavelengths of 1.35 and 1.54 μm has been experimentally demonstrated. The experimental data are analyzed in the framework of a phenomenological model when the Co²⁺ ions are described as three sets of linear dipoles oriented along the crystallographic axes. Ground-state and excited state absorption cross-sections at 1.35 and 1.54 μm are evaluated to be σ_gsa=(4.0±0.3)×10^-19, σ_esa=(3.6±0.4)×10^-20 cm² and σ_gsa=(5.1±0.3)×10^-19, σ_esa=(4.6±0.4)×10^-20 cm², respectively. PACS 42.55.Rz; 71.20.Be     

The effective reinforcement of magnesium alloy ZK60A using Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

ZK60A nanocomposite containing Al₂O₃ nanoparticle reinforcement (50 nm average size) was fabricated using solidification processing followed by hot extrusion. The nanocomposite exhibited similar grain size to the monolithic alloy, reasonable Al₂O₃ nanoparticle distribution, non-dominant (0 0 0 2) texture in the longitudinal direction, and 15% higher hardness than the monolithic alloy. Compared to the monolithic alloy (in tension), the nanocomposite exhibited lower yield strength (0.2%TYS) (−4%) and higher ultimate strength (UTS), failure strain, and work of fracture (WOF) (+13%, +170%, and +200%, respectively). Compared to the monolithic alloy (in compression), the nanocomposite exhibited lower yield strength (0.2%CYS) (−5%) and higher ultimate strength (UCS), failure strain, and WOF (+6%, +41%, and +43%, respectively). The effects of Al₂O₃ nanoparticle addition on the enhancement of tensile and compressive properties of ZK60A are investigated in this article.     

Synthesis and characterization of hollow nanoparticles of crystalline Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>

Although Gd₂O₃ (gadolinia) nanoparticle is the subject of intense research interest due to its magnetic property as well as controllable emission wavelengths by doping of various lanthanide ions, it is known to be difficult to prepare monodisperse crystalline gadolinia nanoparticles because it requires high temperature thermal annealing process to enhance the crystallinity. In this article, we demonstrate the synthesis of hollow nanoparticles of crystalline Gd₂O₃ by employing poly(N-vinylpyrrolidone) (PVP) to stabilize the surface of Gd(OH)CO₃·H₂O nanoparticles and to successively form SiO₂ shell as a protecting layer to prevent aggregation during calcinations processes. Silica shells could be selectively removed after calcinations by a treatment with basic solution to give hollow nanoparticles of crystalline Gd₂O₃. The formation mechanism of hollow nanoparticles could be suggested based on several characterization results of the size and shape, and crystallinity of Gd₂O₃ nanoparticles by TEM, SEM, and XRD.     

Synthesis of ZnAl<Subscript>2</Subscript>O<Subscript>4</Subscript>/α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> complex substrates and growth of GaN films

With the solid phase reaction between pulsed-laser-deposited (PLD) ZnO film and α-Al₂O₃ substrate, ZnAl₂O₄/α-Al₂O₃ complex substrates were synthesized. X-ray diffraction (XRD) spectra show that as the reaction proceeds, ZnAl₂O₄ changes from the initial (111)-oriented single crystal to poly-crystal, and then to inadequate (111) orientation. Corresponding scanning electron microscope (SEM) images indicate that the surface morphology of ZnAl₂O₄ transforms from uniform islands to stick structures, and then to bulgy-line structures. In addition, XRD spectra present that ZnAl₂O₄ prepared at low temperature is unstable at the environment of higher temperature. On the as-obtained ZnAl₂O₄/α-Al₂O₃ substrates, GaN films were grown without any nitride buffer using light-radiation heating low-pressure MOCVD (LRH-LP-MOCVD). XRD spectra indicate that GaN film on this kind of complex substrate changes fromc-axis single crystal to poly-crystal as ZnAl₂O₄ layer is thickened. For the single crystal GaN, its full width at half maximum (FWHM) of X-ray rocking curve is 0.4°. Results indicate that islands on thin ZnAl₂O₄ layer can promote nucleation at initial stage of GaN growth, which leads to the (0001)-oriented GaN film.     

Synthesis of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles with tunable magnetism by the modified hydrothermal method

Cobalt ferrite (CoFe₂O₄) nanoparticles were synthesized by using the hydrothermal route with the addition of trisodium citrate dihydrate (Na₃CA·2H₂O). The formation of CoFe₂O₄ nanoparticles with size ranging from 13 to 19 nm was confirmed by X-ray diffraction, energy dispersive X-ray analysis, and Fourier transform infrared spectroscopy; the clear-cut sharp of the nanoparticles was observed by transmission electron microscopy. By these characterization methods, the evolution of lattice constant and morphologies of the nanoparticles with the addition of Na₃CA·2H₂O is observed. Furthermore, the magnetic hysteresis loops measured at room temperature indicate that the magnetic properties of the products also show clear relationship with the masses of Na₃CA·2H₂O. For example, coercivity and high-field paramagnetic susceptibility increase with the increasing masses of Na₃CA·2H₂O, whereas the saturation magnetization and the effective magnetic anisotropy constant have the maximum values as the mass of Na₃CA·2H₂O is 1 g. This change of magnetic properties is related with the expanded lattice and the varied size and shape because of the addition of Na₃CA·2H₂O.     

Plasmachemical synthesis and basic properties of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> magnetic nanoparticles

Cobalt-ferrite (CoFe₂O₄) nanoparticles (CFNPs) are obtained using direct plasmachemical synthesis in the plasma of a low-pressure arc discharge. The formation of the CFNPs with an average size of 9 nm and a narrow granulometric composition is established employing the methods of X-ray structure analysis and transmission microscopy. The CFNP behavior upon high-temperature annealing is analyzed. The CFNP functional groups are determined using the infrared Fourier spectrum. The results of the X-ray energy dispersion confirm the correspondence of the ratio of the number of atoms of each material to the nominal stoichiometry. The basic magnetic properties of the obtained and annealed samples are investigated at room temperature using the vibrating spectrum magnetometry (VSM).     

Effect of synthesis on the magnetostrictive properties of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> spinel ferrite

The correlation between methods of synthesis and magnetostrictive properties of ferrite materials is investigated. CoFe₂O₄ spinel ferrite was synthesized using three techniques: solid-phase reactions, thermal hydrolysis, and sol-gel. The effect of the method of synthesis on the magnetostrictive properties of spinel ferrite is demonstrated.     

Synthesis of spinel LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> as advanced cathode via a modified oxalate co-precipitation method

Spinel-type LiNi_0.5Mn_1.5O₄ (LNMO) cathode materials for lithium ion batteries have been synthesized via a modified oxalate co-precipitation method. By virtue of the co-precipitation of Li⁺ with transition metal ions, the target materials can be obtained through one-pot reaction without subsequent mixing with lithium salts. What’s more, a uniform distribution between the lithium and transition metal ions at molecular level could be realized, which is beneficial for final electrochemical performances. The physical and electrochemical properties of the material are characterized by XRD, TGA, EDS, FT-IR, SEM, CV, EIS, and charge/discharge tests. The results prove that the as-prepared material owns a cubic spinel structure with a space group of Fd-3m, high crystallinity, uniform particle size, and excellent electrochemical performances. A higher initial capacity and superior rate performance are delivered compared with that of material by conventional co-precipitation method. High capacities of 131.7 and 104.0 mAh g^?1 could be displayed at 0.5 and 10 C, respectively. Excellent cycle stability is also demonstrated with more than 98.5 % capacity retention after 100 cycles at 1 C.     

One-step synthesis of colloidal Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> and γ-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles at room temperature

A facile room-temperature synthesis has been developed to prepare colloidal Mn₃O₄ and γ-Fe₂O₃ nanoparticles (5 to 25 nm) by an ultrasonic-assisted method in the absence of any additional nucleation and surfactant. The morphology of the as-prepared samples was observed by transmission electron microscopy. High-resolution transmission electron microscopy observations revealed that the as-synthesized nanoparticles were single crystals. The magnetic properties of the samples were investigated with a superconducting quantum interference device magnetometer. The possible formation process has been proposed.     

Synthesis of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> by molten salt technique

Lithium manganese oxide powders have been successfully prepared by a molten salt synthesis using eutectic mixture of LiCl and MnO₂ salt at 900 °C. The synthesis was performed in open atmosphere. The crystalline powders were characterized for their phase identification using X-ray diffraction analysis. The physicochemical properties of the lithium manganese oxide powders are investigated by thermal analysis (thermo gravimetric analysis/ differential thermal analysis), Fourier transform infrared spectroscopy, Raman spectroscopy, atomic absorption spectroscopy, electron spin resonance spectroscopy, and scanning electron microscopy. This work shows the feasibility for obtaining lithium manganese oxide at low-temperature molten salt flux method.     

Synthesis of In<Subscript>2</Subscript>O<Subscript>3</Subscript>nanoparticles by thermal decomposition of a citrate gel precursor

This paper describes the synthesis of indium oxide by a modified sol–gel method, and the study of thermal decomposition of the metal complex in air. The characterization of the intermediate as well as the final compounds was carried out by thermogravimetry, differential thermal analysis, Fourier transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy, and small angle X-ray scattering. The results show that the indium complex decomposes to In₂O₃ with the formation of an intermediate compound. Nanoparticles of cubic In₂O₃ with crystallite sizes in the nanosize range were formed after calcination at temperatures up to 900°C. Calcined materials are characterized by a polydisperse distribution of spherical particles with sharp and smooth surfaces.This revised version was published online in August 2005 with a corrected issue number.     

Influence of the preparation method on the morphology of templated NiCo<Subscript>2</Subscript>O<Subscript>4</Subscript> spinel

The synthesis of NiCo₂O₄ spinel by several nanocasting strategies (i.e., multi-step nanocasting, one-step nanocasting and soft-templating), in which nickel and cobalt nitrates are used as precursors and Pluronic P123 as surfactant, is explored. First, in the multi-step nanocasting, the effect of the impregnation method (evaporation, solid–liquid and two-solvent) of the SBA-15 silica template on the morphology of NiCo₂O₄ replica is investigated. The evaporation method seems to be the best choice to obtain mesoporous NiCo₂O₄ powder which, after calcination at 375 °C and subsequent template removal, displays the highest surface area (93.1 m²/g). We have also checked the feasibility of the one-step nanoscating approach for the synthesis of ordered NiCo₂O₄ arrays, though this methodology entails severe difficulties, mainly related to the different decomposition temperature of the nitrate precursors and the P123 surfactant. Finally, randomly oriented, aggregated NiCo₂O₄ nanoparticles are obtained by means of P123 surfactant-assisted soft-templating approach.     

Magnetic and dielectric response of cobalt-chromium spinel CoCr<Subscript>2</Subscript>O<Subscript>4</Subscript> in the terahertz frequency range

The nature of the phonon and magnon modes in the CoCr₂O₄ multiferroic with a cubic spinel structure has been studied using submillimeter spectroscopy and infrared Fourier spectroscopy. This paper reports on the first measurement of the evolution with temperature of the exchange optical magnon in the ferrimagnetic (T _C = 94 K) and two low-symmetry (T _S ≈ 26 K, T _lock-in = 14.5 K) phases of CoCr₂O₄ down to T = 5 K in zero magnetic field. It has been shown that the detected magnon is not a ferrimagnetic order parameter and originates, most probably, from spin precession in the cobalt sublattices. At the points of the magnetic phase transitions, the oscillator parameters of the two lowest-frequency phonon modes reveal an anomalous temperature behavior, thus evidencing the presence of significant interaction between the magnetic and phonon subsystems. The increase by 25% of the damping parameter of the phonon mode originating from vibrations of the CoO₄ tetrahedra during the transition of CoCr₂O₄ to the multiferroic state (T < T _S ) suggests structural changes in the lattice involving loss of spatial central symmetry of the medium.     

Elevated electrochemical property of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> originated from nano-sized Mn<Subscript>3</Subscript>O<Subscript>4</Subscript>

By employment of nano-sized pre-prepared Mn₃O₄ as precursor, LiMn₂O₄ particles have been successfully prepared by facile solid state method and sol-gel route, respectively. And the reaction mechanism of the used precursors of Mn₃O₄ is studied. The structure, morphology, and element distribution of the as-synthesized LiMn₂O₄ samples are characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Compared with LiMn₂O₄ synthesized by facile solid state method (SS-LMO), LiMn₂O₄ synthesized by modified sol-gel route (SG-LMO) possesses higher crystallinity, smaller average particle size (~175 nm), higher lithium chemical diffusion coefficient (1.17 × 10^?11 cm² s^?1), as well as superior electrochemical performance. For example, the cell based on SG-LMO can deliver a capacity of 85.5 mAh g^?1 at a high rate of 5 °C, and manifests 88.3% capacity retention after 100 cycles at 0.5 °C when cycling at 45 °C. The good electrochemical performance of the cell based on SG-LMO is ascribed mainly to its small particle size, high degree of dispersion, and uniform element distribution in bulk material. In addition, the lower polarization potential accelerates Li⁺ ion migration, and the lower atom location confused degree maintains integrity of crystal structure, both of which can effectively improve the rate capability and cyclability of SG-LMO.