Effect of oxygen activity and water partial pressure to degradation rate of Ni cermet electrode contacting Zr<Subscript>0.84</Subscript>Y<Subscript>0.16</Subscript>O<Subscript>1.92</Subscript> electrolyte

The time curves of full polarization resistance of Ni cermet electrode modified with CeO_{2 − δ} additive were studied by means of impedance spectroscopy in binary gas mixtures x% H₂ + (100 − x)% H₂O, 10% CO + 90% CO₂ and multicomponent gas mixtures H₂ + CO₂ + H₂O + CO + Ar of various composition at the temperature of 900°C. The Ni cermet electrode degradation rate in binary gas mixtures H₂ + H₂O was shown to increase sharply at the partial water pressure over 45%. The Ni cermet electrode degradation rate in the mixture of 10% CO + 90% CO₂ was significantly lower than that in 10% H₂ + 90% H₂O. The major changes in the electrode characteristics upon long exposure in working conditions were accounted for by changes in the high-frequency partial polarization resistance. In the course of long testing, the electrode microstructure was not significantly changed. In the presence of hydrogen-containing components (H₂ and H₂O), the carbon-containing components (CO and CO₂) were shown to make an insignificant contribution to the current generation processes in Ni cermet electrode. It was suggested that strong degradation of Ni cermet electrode was caused by poisoning its reaction sites with strongly linked adsorption forms of water (hydroxyls) at the positive charge of electrode.     

Gas diffusion electrodes for polymer electrolyte fuel cell using sulfonated polyimide

Gas diffusion electrodes for high temperature polymer electrolyte fuel cells (PEFCs) have been prepared by using a novel proton conductive sulfonated polyimide (SPI) electrolyte. The catalyst layer was composed of Pt-loaded carbon black (Pt-CB) and SPI ionomer. The polarization properties and the microstructure of the catalyst layer were investigated as a function of the SPI/CB weight ratio. The anodic polarization was found to be negligibly small for all the compositions examined. The highest cathode performance was obtained at SPI/CB = 0.5 (by weight), where the best balance of high catalyst utilization and oxygen gas diffusion rate through the ionomer was obtained.     

Sintering behavior and ionic conductivity of Ce<Subscript>0.8</Subscript>Gd<Subscript>0.2</Subscript>O<Subscript>1.9</Subscript> with a small amount of MnO<Subscript>2</Subscript> doping

A 20% GdO_1.5 doped ceria solid solution with a small amount of MnO₂ doping (≤5% molar ratio) was prepared via the mixed oxide method from high-purity commercial powders with grain size around 0.2–0.5 μm. X-ray diffraction analysis indicated that all the samples exhibited the fluorite structure, and no new phase was found. The data from dilatometeric measurements and scanning electron microscopy observations revealed that 1% Mn doping reduced the sintering temperature by over 150 °C, and enhanced the densification and grain growth. Mn doping has little effect on grain interior conductivity, but a marked deterioration in grain boundary behavior is observed. This leads to a lower total conductivity in comparison with the undoped Ce_0.8Gd_0.2O_2–δ. Therefore, for solid oxide fuel cells (SOFCs) with Mn-containing compounds as electrodes, optimization of electrode fabrication conditions is needed to prevent the formation of a lower conductivity layer at the electrode/electrolyte interface since Mn will diffuse from the electrode side to the electrolyte during fabrication and operation of SOFCs. Electronic Publication     

Interaction of solid electrolyte La<Subscript>0.88</Subscript>Sr<Subscript>0.12</Subscript>Ga<Subscript>0.82</Subscript>Mg<Subscript>0.18</Subscript>O<Subscript>2.85</Subscript> with hydrogen,water vapor,and carbon dioxide

The air,Au/La_0.88Sr_0.12Ga_0.82Mg_0.18O_2.85/Au,air cells are studied by an impedancemetry method before and after a week-long exposure at 700°C to atmospheres of hydrogen, humid air, and carbon dioxide. Blank specimens of the same electrolyte are examined by methods of x-ray diffraction, Raman scattering (RS), and x-ray photoelectron spectroscopy. The fact that the shape of the RS spectra and the shape of the electrode impedance dispersion alter unequivocally suggests that, at the very least, the electrode surface interacts with all the gases. The interaction in question is reversible in the case of hydrogen and carbon dioxide. In the case of water vapor, the interaction is irreversible.Translated from Elektrokhimiya, Vol. 41, No. 2, 2005, pp. 198–205.Original Russian Text Copyright © 2005 by Shkerin, Kovyazina, Beresnev, Kalashnikova, Martemyanova.This revised version was published online in April 2005 with corrections to the article note and article title and cover date.     

Determination of diffusion coefficients for sulfide ions in solid electrolytes on the basis of BaSm<Subscript>2</Subscript>S<Subscript>4</Subscript> and CaGd<Subscript>2</Subscript>S<Subscript>4</Subscript>

Coefficients of self-diffusion and coefficients of diffusion of the sulfur ion in solid electrolytes BaSm₂S₄ and CaGd₂S₄ are determined with recourse to methods of conductimetry and potentiostatic chronoamperometry. A vacancy mechanism for the defect formation in solid solutions on the basis of barium thiosamarate and calcium thiogadolynate is proposed.     

Use of solid electrolyte GeSe-GeI<Subscript>2</Subscript> for electrochemical doping with germanium

Lead tellurite is study to show that solid electrolyte GeSe-GeI₂, which has the optimum composition and contains 5 mol % of GeI₂, can in principle be used for electrochemical doping of semiconducting materials with germanium by the coulometric titration method. Some parameters of the coulometric titration are considered. The doping efficiency is monitored by determining variations in the concentration of charge carriers using the Hall method and by measuring the EMF of corresponding galvanic cells.     

Mass transfer in porous systems, flooded in part with water, of gas diffusion and catalytic layers of the cathode of a fuel cell with a solid polymer electrolyte

Mass transfer in porous gas diffusion and catalytic layers of the cathode of a hydrogen-air fuel cell with a solid polymer electrolyte is considered. The transport processes are considered with allowance made for the partial flooding of porous systems of these layers with water, which forms during the fuel cell operation. The consideration also allows for the influence of the diluent gas present when air oxygen is used as the oxidant. The fraction of water-flooded pores is calculated within percolation theory as a function of structural parameters of the porous system. Conditions leading to the beginning of the gas diffusion layer flooding are presented.     

Solid vitreous inorganic electrolytes in Li<Subscript>2</Subscript>O-LiF-P<Subscript>2</Subscript>O<Subscript>5</Subscript> system for rechargeable lithium power sources: Ionic conductivity and activation energy

The effect of chemical composition to ionic conductivity and activation energy of vitreous solid electrolytes (SE) based on Li₂O-P₂O₅-LiF system (Li₂O ≥ 45.4 mol %) was detected. The temperature effect to conductivity and activation energy was studied. An original technology was designed to prepare vitreous SEs in Li₂O-P₂O₅-LiF system containing up to 20 mol % LiF and characterized with ionic conductivity up to 4.4 × 10^?7 S cm^?1 (24°C) and activation energy about 0.567 eV. The synthesized materials are characterized with high X-ray amorphism and technological performance.     

Conductivity and thermal expansion of the Ce<Subscript>0.8</Subscript>Gd<Subscript>0.2</Subscript>O<Subscript>1.9</Subscript> solid electrolyte in the oxidizing and reducing atmospheres

Highly compact (99%) solid electrolyte Ce_0.8Gd_0.2O_1.9 with submicron (0.3 μm) grains is synthesized. The dilatometric (20–850°C) and conductivity (180–350°C) measurements are performed on the electrolyte in air and as a function of the partial oxygen pressure \(p_{O_2 } \) (0.21?1×10^?25 atm) at 600, 700, and 800°C. An inflection is found in the temperature dependences of the thermal coefficient of linear expansion and conductivity (impedance measurements) at ～230°C, which is the evidence for a phase transition. The activation energies for conduction in the grain bulk and boundaries differ only slightly, indicating that the grain boundaries’ resistance is caused not by the precipitation of the second phase at the boundaries, but most probably by the presence of intergranular nanopores. The dilatometric measurements confirm a significant increase in the linear dimensions of Ce_0.8Gd_0.2O_1.9 in the reducing atmospheres with a parallel increase in its electron conductivity. The electron conductivity and specific elongation increase proportionally to \(p_{O_2 }^{ - 1/4} \) at all temperatures. The \(p_{O_2 } \) values, at which the transport numbers of ions t _i = 0.5, are determined. They are 10^?22.5, 10^?20, and 10^?18 atm at 600, 700, and 800°C, respectively.     

Electrochemical behavior of composite cathodes in contact with solid electrolyte La<Subscript>10</Subscript>Ge<Subscript>6</Subscript>O<Subscript>27</Subscript>

The cathodic overvoltage of composite cathodes 50 wt % La_0.8Sr_0.2MnO₃ (LSM) + 50 wt % La₁₀Ge₆O₂₇ (LGO) (further on, LSM-LGO), LSM-SSZ (Zr_0.835Sc_0.165O_2?δ), Ag-Pd-LGO, and Ag-Pd-SSZ in contact with the LGO electrolyte is measured. The temperature dependences of the polarization conductivity and the working-current densities of the same composite cathodes are investigated. The study is performed at 700–900°C. A comparison with the SSZ electrolyte is conducted. The chemical interaction in the LSM-LGO composition is studied. It is demonstrated that the interaction of lanthanum-strontium manganite with lanthanum germanate occurs with the dissolution of the initial phases in one another and with the formation of fresh phases at elevated temperatures. Coefficients of linear thermal expansion of the LGO and SSZ electrolytes and the LSM, LSM-LGO, and LSM-SSZ electrode materials are compared at 40–900°C. Most of the studied electrodes in contact with the LGO electrolyte demonstrate thermomechanical stability and high electrochemical activity.     

SOFC中干甲烷浓度对Ni-YSZ阳极上反应的影响

为探讨固体氧化物燃料电池(solid oxide fuel cell, SOFC)中干甲烷浓度对反应的影响,采用色谱在线测量阳极尾气,总结阳极尾气的变化规律。在此基础上,分析干甲烷在固体氧化物燃料电池Ni-YSZ阳极上的反应,寻找干甲烷浓度与电流对电池阳极反应影响的数学关系。结果表明,随着电流密度的增加,低浓度甲烷按顺序发生CH₄+O^2- → CO+2H₂+2e^-、CH₄+2O^2- → CO+H₂O+H₂ +4e^-、CH₄+3O^2- → CO+2H₂O + 6e^-、CH₄+4O^2- → CO₂+2H₂O+8e^-反应,高浓度甲烷只发生甲烷的第一个氧化反应,中浓度甲烷发生前两个或前三个反应。依据法拉第第一定律及反应物之间的关系,确定甲烷的低、中、高浓度的判定依据分别为:q_v(CH₄)≤I/(4F)、I/(4F)≤q_v(CH₄)≤I/(2F)、q_v(CH₄)≥I/(2F)。     

Thermodynamic study of the Ag-As-Se and Ag-S-I systems using the EMF method with a solid Ag<Subscript>4</Subscript>RbI<Subscript>5</Subscript> electrolyte

The EMF method with a solid Ag₄RbI₅ superionic conductor was used to study the Ag-As-Se and Ag-S-I systems in the composition ranges of Ag₂Se-As₂Se₃-Se and Ag₂S-AgI-S, accordingly. Their solid-phase equilibrium diagrams are constructed or specified. The existence of ternary AgAs₃Se₅, AgAsSe₂, Ag₃AsSe₃, Ag₇AsSe₆, Ag₃SI compounds is confirmed. The standard partial and integral thermodynamic formation functions and also standard entropies were calculated for these compounds for the first time.     

Polarization Characteristics of Composite Electrodes in Electrochemical Cells with Solid Electrolytes Based on CeO<Subscript>2</Subscript> and LaGaO<Subscript>3</Subscript>

For two types of electrochemical cells with oxygen-conducting solid electrolytes based on lanthanum gallate (LSGM) and cerium oxide (SDC) studied are the temperature dependences of the polarization conductivity of air electrodes prepared from lanthanum-strontium manganite (LSM) and composites LSM-LSGM, LSM-SDC, and LSM-SSZ (SSZ is zirconium dioxide-based electrolyte). Effect of praseodymium oxide, added into these electrodes as a modifier, on their electrochemical properties is examined. Electrochemical systems with an LSM/LSGM interface exhibit low electrochemical activity toward the oxygen reaction, because during the formation of electrodes, LSM interacts with LSGM to form a poorly conducting product.__________Translated from Elektrokhimiya, Vol. 41, No. 5, 2005, pp. 602–606.Original Russian Text Copyright © 2005 by Yaroslavtsev, Kuzin, Bronin, Bogdanovich.     

Effect of anodic current on carbon dioxide reforming of methane on Pt electrode in a cell with solid oxide electrolyte

The carbon dioxide reforming of methane in a cell with a solid oxygen-conducting electrolyte:

Cathode of a fuel cell with a solid polymer electrolyte: Calculating overall currents in the presence of a gas-diffusion layer

Mathematical apparatus, which makes it possible to perform calculations of the current-voltage characteristics of cathodes of fuel cells with a solid polymer electrolyte in conditions where there are present extraneous diffusion restrictions is proposed. In so doing, the partial pressure of oxygen and the absolute pressure of gas in the gas chamber may assume any values. First of all presented are the results of calculations of the current-voltage characteristics intrinsic to active layers of the air and oxygen cathodes, which are performed under the assumption that the extraneous diffusion restrictions are absent altogether. Thereafter, in the same conditions (at the same parameters that characterize the active layer of a cathode), obtained are results of a calculation of the current-voltage characteristics inherent in the air and oxygen cathodes in the presence of extraneous diffusion restrictions. Afterward there is performed an analysis of the way a gas-diffusion layer restricts the process of generation of current in a cathode and of what measures should be taken in order for the extraneous diffusion restrictions to become less significant.     

Oxidative conversion of methane and methanol on M/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/cordierite structured metal oxide catalysts (m = Ni,Cu, Zn)

A study was carried out on the properties of Ni/Al₂O₃ and Cu-ZnO/Al₂O₃ composites supported on ceramic honeycomb monoliths made from synthetic cordierite in the carbon dioxide conversion of methane and the partial oxidation of methanol. The structured nickel-alumina catalysts are significantly more efficient than the conventional granulated catalysts. The improved working stability of these catalysts was achieved by adjusting the acid-base properties of the surface by introducing sodium and potassium oxides, which leads to inhibition of surface carbonization. The hydrogen yield was close to 90% in the partial oxidation of methanol with a stoichiometric reagent ratio in the presence of the Cu-ZnO/Al₂O₃/cordierite catalyst. A synergistic effect was found, reducing the selectivity of CO formation in the presence of the Cu-ZnO catalyst relative to samples derived from the individual components Cu and ZnO. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 43, No. 5, pp. 299–306, September–October, 2007.     

Cathode of a hydrogen-oxygen fuel cell with a solid polymer electrolyte: The effect of the flooding of pores by water on the characteristics of the active layer

A computer model of the active layer of the cathode of a hydrogen-oxygen fuel cell with a solid polymer electrolyte is studied. The active mass of the electrode consists of equidimensional grains of the substrate (agglomerates of carbon particles with platinum particles embedded in them) and a solid polymer electrolyte (Nafion). The flooding by water can be experienced by both the pores in the substrate grains, which facilitate the oxygen penetration into the active layer of the electrode, and the voids between the grains. All possible versions of the flooding of these pores by water are considered. A calculation of the optimum, at a given polarization of the electrode, value of electrochemical activity, the thickness of the active layer, and the weight of platinum is performed. The major parameters of the system are the concentrations of grains of the substrate and solid polymer electrolyte, the size of these grains, the platinum concentration in the substrate grains, the average diameter of pores in the substrate grains, and the polarization of electrodes. The ultimate aim of the work is to estimate how the flooding of pores of the active layer of the cathode by water affects the magnitude of the optimum current, the effective thickness of the active layer, and the weight of platinum.Translated from Elektrokhimiya, Vol. 41, No. 1, 2005, pp. 35–47.Original Russian Text Copyright © 2005 by Chirkov, Rostokin.     

Cyclic voltammetric study on the catalysis of electrodeposited manganese oxide on the electrochemical oxygen reduction reaction (ORR) in room temperature ionic liquids (RTILs) of 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIBF<Subscript>4</Subscript>) on glassy carbon clectrode

For the first time, the electrochemical oxygen reduction reaction (ORR), was investigated using cyclic voltammetry (CV) on the electrodeposited manganese oxide (MnO _x )-modified glassy carbon (MnO _x -GC) electrode in the room temperature ionic liquids (RTILs) of EMIBF₄, i.e. 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIBF₄). The results demonstrated that, after being modified by MnO _x on a GC electrode, the reduction peak current of oxygen was increased to some extent, while the oxidation peak current, corresponding to the oxidation of superoxide anion, i.e., O₂⁻ was attenuated in some degree, suggesting that MnO _x could catalyze ORR in RTILs of EMIBF₄, which is consistent with the results obtained in aqueous solution. To accelerate the electron transfer rate, multi-walled carbon nanotubes (MWCNTs) was modified the GC electrode, and then MnO _x was electrodeposited onto the MWCNTs-modified GC electrode to give rise to a MnO _x /MWCNTs-modified GC electrode, consequently, the improved standard rate constant, k_s, originated from the modified MWCNTs, along with the modification of electrodeposited MnO _x , showed us a satisfactory electrocatalysis for ORR in RTILs of EMIBF₄. Published in Russian in Elektrokhimiya, 2009, Vol. 45, No. 3, pp. 340–345. The article is published in the original.     

Effect of Bi0.75Y0.25O1.5 electrolyte additive in collector layer to properties of bilayer composite cathodes of solid oxide fuel cells based on La(Sr)MnO3 and La(Sr)Fe(Co)O3 compounds

The sintering features, electroconductivity, and electrochemical characteristics of bilayer electrodes with functional composite layers based on La(Sr)MnO₃ (LSM) and La(Sr)Fe(Co)O₃ with LSM collector layer and Bi(Y)O_1.5 (YDB) electrolyte additive in contact with Ce (Sm)O₂(SDC), La(Sr)Ga(Mg)O₃, and Zr(Sc)O₂ electrolytes were studied. YDB additive to the electrode collector layer was shown to produce a positive effect to the properties of the studied electrode systems. The maximum electrochemical activity and electroconductivity was observed for the electrodes with 5 wt % of YDB electrolyte additive in the collector layer. Thus, electroconductivity of electrodes is almost doubled and 100 mV cathode overvoltage current density is increased by 30% at the temperatures of 800 to 900°C and up to 10-fold at 650 to 700°C. The collector layer sintering temperature of bilayer electrodes can be reduced from 1150 to 1000°C without loss of electrochemical activity. The service life tests (about 1200 h) of composite electrodes with LSM2-SDC functional layer and 90% LSM2 + 10% YDB collector layer in contact with SDC electrolyte showed the time dependences of polarization resistance tending to saturation and described with damped exponent. Original Russian Text ? N.M. Bogdanovich, D.I. Bronin, G.K. Vdovin, I.Yu. Yaroslavtsev, B.L. Kuzin, 2009, published in Elektrokhimiya, 2009, Vol. 45, No. 4, pp. 486–494.