Nanocrystalline CaCu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript> powders prepared by egg white solution route: synthesis,characterization and its giant dielectric properties

Nanocrystalline CaCu₃Ti₄O₁₂ powders with particle sizes of 50–90 nm were synthesized by a simple method using Ca(NO₃)₂·4H₂O, Cu(NO₃)₂·4H₂O, titanium(diisoproproxide) bis(2,4-pentanedionate) and freshly extracted egg white (ovalbumin) in aqueous medium. The synthesized precursor was characterized by TG-DTA to determine the thermal decomposition and crystallization temperature which was found to be at above 400 °C. The precursor was calcined at 700 and 800 °C in air for 8 h to obtain nanocrystalline powders of CaCu₃Ti₄O₁₂. The calcined CaCu₃Ti₄O₁₂ powders were characterized by XRD, FTIR, SEM and TEM. Sintering of the powders was conducted in air at 1100 °C for 16 h. The XRD results indicated that all sintered samples have a typical perovskite CaCu₃Ti₄O₁₂ structure and a small amount of CuO, although the sintered sample of the 700 °C calcined powders contained some amount of CaTiO₃. SEM micrographs showed the average grain sizes of 12.0±7.8 and 15.5±8.9 μm for the sintered CaCu₃Ti₄O₁₂ ceramics prepared using the CaCu₃Ti₄O₁₂ powders calcined at 700 and 800 °C, respectively. The sintered samples exhibit a giant dielectric constant, ε^′ of ∼ 1.5–5×10⁴. The dielectric behavior of both samples exhibits Debye-like relaxation, and can be explained based on a Maxwell–Wagner model. PACS 77.22.Gm; 81.05.Je; 81.07.Wx; 81.20.Ev     

Manganese doping effects on interband electronic transitions,lattice vibrations,and dielectric functions of perovskite-type Ba<Subscript>0.4</Subscript>Sr<Subscript>0.6</Subscript>TiO<Subscript>3</Subscript> ferroelectric ceramics

The Ba_0.4Sr_0.6−x Mn _x TiO₃ (BSMT) ceramics with different Mn composition (from 1% to 10%) have been prepared via the conventional solid-state reaction sintering. The X-ray diffraction analysis shows that the ceramics are polycrystalline with the single perovskite phase. The lattice vibrations and optical properties have been investigated using Raman scattering, spectroscopic ellipsometry (SE), and infrared reflectance spectra. It was found that the optical bandgap for the BSMT ceramics is varied between 3.40 and 3.65 eV. The three first-order Raman-active phonon modes can be observed, and the frequency of the A ₁(LO₃)/E(LO) mode shows a blue shift of 8 cm⁻¹ with the Mn composition, which can be attributed to the distortion of the TiO₆ octahedron. With increasing Mn composition, the frequency of the infrared-active TO₄ mode decreases from 532 to 520 cm⁻¹, owing to the local variation of the lattice constant induced by the Mn incorporation. Moreover, the optical functions of the ceramics from the far-infrared to ultraviolet region are obtained based on the SE and reflectance spectra, which is useful for the potential applications in ferroelectric-based optoelectronic devices.     

Microstructure,dielectric and piezoelectric properties of (K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>)NbO<Subscript>3</Subscript>-Ba(Ti<Subscript>0.95</Subscript>Zr<Subscript>0.05</Subscript>)O<Subscript>3</Subscript> lead-free ceramics with CuO sintering aid

Using an ordinary ceramic fabrication technique, we fabricated lead-free (1-x)(K_0.5Na_0.5)NbO₃-xBa(Ti_0.95Zr_0.05)O₃ ceramics with CuO sintering aid . Ba(Ti_0.95Zr_0.05)O₃ diffuses into (K_0.5Na_0.5)NbO₃ to form a new solid solution. The ceramics with perovskite structure possess orthorhombic phase at x≤0.04 and become tetragonal phase at x≥0.06. Both the paraelectric cubic–ferroelectric tetragonal and the ferroelectric tetragonal–ferroelectric orthorhombic phase transition temperatures decrease with increasing the concentration of Ba(Ti_0.95Zr_0.05)O₃. The doping of CuO effectively promotes the densification of the ceramics. The coexistence of the orthorhombic and tetragonal phases at 0.04<x<0.06 and the improvement in sintering performances of the ceramics significantly enhance the piezoelectric and dielectric properties at room temperature. The ceramics with x=0.04–0.06 and y=0.75–1.50 possess excellent properties: d₃₃=119–185 pC/N, k_P=37–44%, k_t=35–49%, ε=341–1129, cosδ=0.7–4.4% and T_c=312–346 °C. PACS 77.65.-j; 77.84.Dy; 77.84.-s     

Preparation and characterization of Yb-doped Ba(Ce,Zr)O<Subscript>3</Subscript> nanopowders with high sinterability

The Ba(Ce_0.8Zr_0.2)_0.95Yb_0.05O_2.975 ceramics electrolyte was prepared via a Pechini method using metal nitrate salts as starting materials. An optimum annealing temperature of 1,400 °C was needed to obtain a pure perovskite-like phase with orthorhombic structure. Particle size distribution showed a bimodal distribution that corresponds to the loose powders and agglomerates size. Scanning electron micrograph revealed that the loose powders were in the nanosize range (70–200 nm). These ultrafine loose powders enhanced the densification of a pellet with relative density ∼95% obtained at 1,400 °C. The sample formed clear and compact grains with submicron sizes. Impedance results showed that the impedance semicircle of the grain was observed only at T ≤ 250 °C. The introduction of 20 mol% Zr improved the chemical stability of BaCe_0.95Yb_0.05O_2.975 sample in atmosphere containing carbon dioxide at 600 °C. The sample also exhibited high proton conductivity in wet hydrogen.     

Dielectric properties of Bi<Subscript>2</Subscript>PbNb<Subscript>2</Subscript>O<Subscript>9</Subscript> ceramics prepared by different techniques

Different techniques for the synthesis of Bi₂PbNb₂O₉, namely the mixed oxide technique, molten salt synthesis, hydrothermal synthesis, co-precipitation and the tartaric acid gel method were investigated and the results on the dielectric properties are reported. The heat-treatment of the precursor powders was the same for all precursor powders. Sintering at 1040 °C under ambient pressure resulted in polycrystalline specimens, while hot-forging at 1040 °C with a pressure of 20 MPa produced c-axis aligned samples. Phase composition and crystallite orientation of the sintered bodies were analyzed by X-ray diffraction. Single-phase material was obtained in all cases. Hot-forging not only yielded c-axis orientation, but also increased the relative densities above 99.4%. The relative permittivity decreased for c-axis oriented material compared to polycrystalline ceramics. Values for the relative permittivity for the hot-forged specimens at 100 °C at 100 kHz varied between 165 and 250, depending on the fabrication method. The Curie temperature for the c-axis aligned samples was 568 °C, independent of the nature of the precursor powders. PACS 77.22.-d; 77.84.-s     

Spherical shape BaO-ZnO-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> glass powders prepared by spray pyrolysis

Fine-sized BaO-ZnO-B₂O₃-SiO₂ (BZBS) glass powders were directly prepared by high temperature spray pyrolysis. The hollow glass powders prepared at low preparation temperature of 1000 °C had a low density of 2.65 g/cm³. However, the densities of the BZBS powders obtained at preparation temperatures of 1200 and 1400 °C were each 3.92 and 4.13 g/cm³. The mean size of the BZBS glass powders prepared by spray pyrolysis at preparation temperature of 1400 °C was 0.98 μm. The glass transition temperature (T_g) of the prepared BZBS glass powders was 518.9 °C. The dielectric layers formed from the prepared BZBS glass powders with a dense structure had a clean surface and a dense inner structure without voids at the firing temperature of 580 °C. The transparencies of the dielectric layers formed from the prepared BZBS glass powders were higher than 90% within the visible range. PACS 42.70.Ce; 85.60.Pg; 71.55.Jv     

Structural evolutions of the mechanically alloyed Al<Subscript>70</Subscript>Cu<Subscript>20</Subscript>Fe<Subscript>10</Subscript> powders

Elemental mixtures of Al, Cu, Fe powders with the nominal composition of Al₇₀Cu₂₀Fe₁₀ were mechanically alloyed in a planetary ball mill for 80 h. Subsequent annealing of the as-milled powders were performed at 600–800°C temperature range for 4 h. Structural characteristics of the mechanically alloyed Al₇₀Cu₂₀Fe₁₀ powders with the milling time and the heat treatment were investigated by X-ray diffraction (XRD), differential scanning calorimeter (DSC) and differential thermal analysis (DTA). Mechanical alloying of the Al₇₀Cu₂₀Fe₁₀ did not result in the formation of icosahedral quasicrystalline phase (i-phase) and a long time milling resulted in the formation of β-Al(Cu,Fe) solid solution phase (β-phase). The i-phase was observed only for short-time milled powders after heat treatment above 600°C. The β-phase was one of the major phases in the Al₇₀Cu₂₀Fe₁₀ alloy. The w-Al₇Cu₂Fe₁ phase (w-phase) was obtained only after heat treatment of the short-time milled and unmilled samples. The present investigation indicated that a suitable technique to obtain a large amount of quasicrystalline powders is to use a combination of short-time milling and subsequent annealing.     

Dielectric and polar order behaviors of BaTiO<Subscript>3</Subscript>-Bi(Mg<Subscript>1/2</Subscript>Ti<Subscript>1/2</Subscript>)O<Subscript>3</Subscript> ceramics

New perovskite solid solution ceramics of (1−x)BaTiO₃-xBi(Mg_1/2Ti_1/2)O₃ ((1−x)BT-xBMT, x≤0.09) were synthesized by the solid-state reaction technique. X-ray diffraction studies have revealed a stable single perovskite structure for all samples. Dielectric measurements were carried out at different frequencies and temperatures. The polarization evolutions with temperatures were measured to investigate the ferroelectric properties. All the compositions show features of ferroelectrics with diffuse phase transition, though the temperature T _m of their dielectric constant maximum ε _m is frequency dependent. The dielectric constant peak ε(T) of (1−x)BT-xBMT ceramics become broad with increasing BMT content. During the temperature range of ε(T) peak summit, (1−x)BT-xBMT ceramics present quasi-linear dielectric phenomenon under high electric field with very high dielectric constant.     

Phase transition and electrical properties of (K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>)(Nb<Subscript>1-x</Subscript>Ta<Subscript>x</Subscript>)O<Subscript>3</Subscript> lead-free piezoelectric ceramics

(K_0.5Na_0.5)(Nb_1-xTa_x)O₃ lead-free piezoelectric ceramics have been prepared by an ordinary sintering technique. The results of X-ray diffraction reveal that Ta⁵⁺ diffuses into the K_0.5Na_0.5NbO₃ lattices to form a solid solution with an orthorhombic perovskite structure. Because of the high melting temperature of KTaO₃, the (K_0.5Na_0.5)(Nb_1-xTa_x)O₃ ceramics can be sintered at higher temperatures. The partial substitution of Ta⁵⁺ for the B-site ion Nb⁵⁺ decreases both paraelectric/cubic–ferroelectric/tetragonal and ferroelectric/tetragonal–ferroelectric/orthorhombic phase transition temperatures, T_C and T_O-T. It also induces a relaxor phase transition and weakens the ferroelectricity of the ceramics. The ceramics become ‘softened’, leading to improvements in d₃₃, k_p, k_t and ε_r and a decease in E_c, Q_m and N_p. The ceramics with x=0.075–0.15 become optimum, having d₃₃=127–151 pC/N, k_p=0.43–0.44, k_t=0.43–0.44, ε_r=541–712, tanδ=1.75–2.48% and T_C=378–329 °C. PACS 77.65.-j; 77.84.Dy; 77.84.-s     

Synthesis of SmAlO<Subscript>3</Subscript> nanocrystalline powders by polymeric precursor method

SmAlO₃ nanocrystalline powders were successfully synthesized by the polymeric precursor method using ethylenediaminetetraacetic acid as a chelating agent. The precursor and the derived powders were characterized by thermogravimetry analysis (TG) and differential scanning calorimetry analysis (DSC), infrared spectroscopy (IR), X-ray diffractometry (XRD) and transmission electron microscopy (TEM). The results showed that pure SmAlO₃ powder with orthorhombic perovskite structure could be synthesized at 800°C for 2 h without formation of any intermediate phase. The average particle size of the powder synthesized at 900°C was as low as 28 nm. Subsequently, the bulk SmAlO₃ ceramics were prepared at various sintering temperatures using the synthesized powders calcined at 900°C for 2 h as starting materials. The sintering experiments indicated that the sample sintered at 1550°C for 2 h exhibited the highest relative density of 97.2% and possessed the best microwave dielectric properties of ε _r=20.94, Q×f=78600 GHz and τ _f=−71.8 ppm/°C.     

Genesis,structural, and transport properties of La<Subscript>2</Subscript>Mo<Subscript>2-x</Subscript>W<Subscript>x</Subscript>O<Subscript>9</Subscript> prepared via mechanochemical activation

Fast oxide-ion conductors La₂Mo_2-xW_xO₉ (x = 0–1) have been prepared using mechanochemical activation (MA) of starting oxides in a high-power planetary ball mill. Studies of La₂Mo_2-xW_xO₉ genesis and structural properties using thermal analysis, XRD, SEM, IR, and Raman spectroscopy have revealed that MA results in the formation of an amorphous precursor, while the cubic β-phase is formed after calcination at 700–900 °C. Due to a high dispersion of powders, high-density pellets of W-LAMOX ceramics have been obtained already after sintering at 950 °C. Their electrical conductivity measured by the impedance spectroscopy depends on the W concentration being sufficiently high (up to 5.6?10^?3 S/cm at 630 °C) at temperatures below 650 °C.     

Structural and electrical properties of 0.7Pb(Mg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript>–0.3PbTiO<Subscript>3</Subscript> thin films grown on Ir/MgO buffered Si(100) substrates

Thin films of 0.7Pb(Mg_1/3Nb_2/3)O₃–0.3PbTiO₃ (PMN-PT) have been grown on Ir/MgO buffered Si(100) substrates at different substrate temperatures by pulsed laser deposition. Crystalline phases as well as preferred orientations in the PMN-PT films were investigated by X-ray diffraction analysis (XRD). The microstructure, dielectric and ferroelectric properties of PMN-PT film prepared at 650 °C were studied. The results show that the film prepared at 650 °C exhibits pure perovskite phase and single c-axis orientation. The dielectric constant and dissipation factor of the single c-axis oriented film are 1000 and 0.04 at a frequency of 1 kHz, while the remnant polarization and coercive field are about 13.0 μC/cm² and 100 kV/cm under an electric field of 480 kV/cm, respectively. PACS 81.15.Fg; 77.80.-e; 77. 22.Ej; 77.55.+f; 85.50.Gk     

Electrophysical properties and the structure of the YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> compound thermally restored after low-temperature decomposition

The electrophysical properties and structure of the nonstoichiometric high-temperature superconductor YBa₂Cu₃O _y restored at T = 930–950°C after low-temperature decomposition (T = 200°C) into phases different in the oxygen content have been studied. It has been shown that, unlike heat treatments at T ≤ 900°C, the superconducting properties are almost completely restored for 3–5 h during grain recrystallization, which is impossible at lower temperatures. After short-term annealing at T = 930–950°C (for 1–2 h), the ceramic material still contains a significant number of structural defects, most likely, in cation sublattices. These defects can contribute to the pinning of magnetic vortices, which substantially increases the critical current density in magnetic fields up to 2 T as compared to ceramic materials produced by the conventional technology.     

Fabrication and laser performance of highly transparent Nd:YAG ceramics from well-dispersed Nd:Y<Subscript>2</Subscript>O<Subscript>3</Subscript> nanopowders by freeze-drying

Well-dispersed Nd:Y₂O₃ powders with uniform particle size of about 60 nm were synthesized from freeze-dried precursors. Highly transparent 2 at.% Nd:YAG ceramics were fabricated from the as-synthesized Nd:Y₂O₃ powders and commercial Al₂O₃ powders by vacuum sintering at 1,750 °C for 5 h. Phase evolution, microstructures, and spectroscopic properties of the Nd:YAG transparent ceramics were investigated. Freeze-drying played an important role in the synthesis of high-quality Nd:Y₂O₃ nanosized powders, which were essential for the fabrication of highly transparent Nd:YAG ceramics. Optical transmittance of a 3-mm thick sample reached 82% in the wavelength range of 200–900 nm. 5.23 W output power was obtained with 14.3 W diode laser pumping, giving a slope efficiency of 36.5%.     

Structural and dielectric characterization of Sr substituted Ba(Zr,Ti)O<Subscript>3</Subscript> based functional materials

Single phase Sr substituted BaZr_0.1Ti_0.9O₃ (also known as BZT) ceramics with a formula Ba_1-xSr_xZr_0.1Ti_0.9O₃ (x=0.10, 0.20, 0.30, 0.40 and 0.50) are prepared using a solid state reaction of mixed oxides at 1250 °C for 15 h. Analysis of XRD patterns of the ceramic powders show that Sr substitutes into Ba sites and reduces the lattice parameter. The powders are sintered at 1600 °C for 6 h to investigate the microstructure and functional properties. It is found that strontium substitution significantly modifies the microstructure and greatly influences the dielectric properties. The increase in Sr content reduces the ceramic grain size and results in spherical grains. With an increase in Sr content, the Curie temperature is lowered, and the relative permittivity maximum is increased and broadened. In Ba_1-xSr_xZr_0.1Ti_0.9O₃ with x=0.30, the relative permittivity reached a maximum of 26600 and with further increase of Sr content, the relative permittivity is lowered and the phase transition is found to be broad and diffused. The ferroelectric hysteresis characteristics are discussed in detail. PACS 77.84.-s; 77.80.Bh; 77.22.Ch; 77.84.Dy; 77.22.-d     

Photoluminescence,thermoluminescence and electron spin resonance studies on Eu<Superscript>3+</Superscript> doped Ca<Subscript>3</Subscript>Al<Subscript>2</Subscript>O<Subscript>6</Subscript> red phosphors

Tricalcium aluminate doped with Eu³⁺ was prepared at furnace temperatures as low as 500°C by using the convenient combustion route and examined using powder X-ray diffraction, scanning electron microscope and photoluminescence techniques. A room-temperature photoluminescence study showed that the phosphors can be efficiently excited by UV/Visible region, emitting a red light with a peak wavelength of 616 nm corresponding to the ⁵D₀–⁷F₂ transition of Eu³⁺ ions. The phosphor exhibits three thermoluminescence (TL) peaks at 195°C, 325°C and 390°C. Electron Spin Resonance (ESR) studies were carried out to study the defect centres induced in the phosphor by gamma irradiation and also to identify the defect centres responsible for the TL process. Room-temperature ESR spectrum of irradiated phosphor appears to be a superposition of three distinct centres. One of the centres (centre I) with principal g-value 2.0130 is identified as O⁻ ion while centre II with an axially symmetric principal values g _∥=2.0030 and g _⊥=2.0072 is assigned to an F⁺ centre (singly ionized oxygen vacancy). O⁻ ion (hole centre) correlates with the TL peak at 195°C and the F⁺ centre (electron centre), which acts as a recombination centre, is also correlated to the 195°C TL peak. F⁺ centre further appears to be related to the high temperature peak at 390°C. Centre III is also assigned to an F⁺ centre and seems to be the recombination centre for the TL peak at 325°C.     

Giant positive magnetoresistance in heterostructure (La<Subscript>0.7</Subscript>Sr<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript>) coated with YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7</Subscript> composites

(La_0.7Sr_0.3MnO₃) _x /(YBa₂Cu₃O₇) _y composites were prepared by mixing La_0.7Sr_0.3MnO₃ powders and the sol–gel-derived YBa₂Cu₃O₇ matrix, followed by high-temperature calcinations. Their structural, magnetic properties and magnetoresistance effect have been investigated systematically. A giant positive magnetoresistance (PMR) at low magnetic field is observed at low temperatures. In the case of (La_0.7Sr_0.3MnO₃)₁/(YBa₂Cu₃O₇)₉ composite, the PMR achieves 260% under a magnetic field of 5800 Oe. However, the PMR value sharply decreases with increasing temperature and no magnetoresistance effects are found above metal-insulator transition temperature. The enhancement of spin-dependent scattering at the grain boundaries should be responsible for the observed PMR. In addition, the temperature dependence of resistance under magnetic field could be explained by the competition between diamagnetism and paramagnetism in YBCO phase. At low temperature, the diamagnetism is predominant over paramagnetism and the interface scattering between LSMO grains is enhanced correspondingly. As a result, the low-temperature resistance increases and large PMR appears.     

Synthesis of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> by molten salt technique

Lithium manganese oxide powders have been successfully prepared by a molten salt synthesis using eutectic mixture of LiCl and MnO₂ salt at 900 °C. The synthesis was performed in open atmosphere. The crystalline powders were characterized for their phase identification using X-ray diffraction analysis. The physicochemical properties of the lithium manganese oxide powders are investigated by thermal analysis (thermo gravimetric analysis/ differential thermal analysis), Fourier transform infrared spectroscopy, Raman spectroscopy, atomic absorption spectroscopy, electron spin resonance spectroscopy, and scanning electron microscopy. This work shows the feasibility for obtaining lithium manganese oxide at low-temperature molten salt flux method.     

A sonochemical-assisted synthesis and annealing temperature effect of La<Subscript>0.7</Subscript>Sr<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript> nanoparticles

This paper reports on the sonochemical-assisted synthesis of La_0.7Sr_0.3MnO₃ (LSMO) nanoparticles (NPs) which have a single-crystalline perovskite structure. The average particle size of LSMO NPs was controlled from about 40 to 120 nm by changing the annealing temperatures from 750 to 1050°C. The particle size, electrical resistivity, and ferromagnetic transition temperature of LSMO NPs were strongly dependent on the annealing temperature. A substantial decrease in resistivity and an enhancement in the insulator–metal transition temperature were found on increasing the annealing temperature. Furthermore, the enhancement in magnetization and paramagnetic–ferromagnetic (PM–FM) transition temperatures was observed as the annealing temperature increases.     

Magnetic state of the structural separated anion-deficient La<Subscript>0.70</Subscript>Sr<Subscript>0.30</Subscript>MnO<Subscript>2.85</Subscript> manganite

The results of neutron diffraction studies of the La_0.70Sr_0.30MnO_2.85 compound and its behavior in an external magnetic field are stated. It is established that in the 4–300 K temperature range, two structural perovskite phases coexist in the sample, which differ in symmetry (groups R[`3]cR\bar 3c and I4/mcm). The reason for the phase separation is the clustering of oxygen vacancies. The temperature (4–300 K) and field (0–140 kOe) dependences of the specific magnetic moment are measured. It is found that in zero external field, the magnetic state of La_0.70Sr_0.30MnO_2.85 is a cluster spin glass, which is the result of frustration of Mn³⁺-O-Mn³⁺ exchange interactions. An increase in external magnetic field up to 10 kOe leads to fragmentation of ferromagnetic clusters and then to an increase in the degree of polarization of local spins of manganese and the emergence of long-range ferromagnetic order. With increasing magnetic field up to 140 kOe, the magnetic ordering temperature reaches 160 K. The causes of the structural and magnetic phase separation of this composition and formation mechanism of its spin-glass magnetic state are analyzed.