Simultaneous determination of diethylene glycol and propylene glycol in pharmaceutical products by HPLC after precolumn derivatization with p-toluenesulfonyl isocyanate

A simple and reliable HPLC method was developed for the simultaneous quantitative analysis of diethylene glycol (DEG) and propylene glycol (PG) in pharmaceutical products by precolumn derivatization. The derivatization reagent p-toluenesulfonyl isocyanate (TSIC, 10 microL, 20% in ACN v/v) was added to 100 microL of the sample, and then 10 muL of water was added. The resulting derivatives were separated using a C(18)analytical column and a mobile phase composed of 0.01 M KH(2)PO(4)buffer (adjusted to pH 2.5 with phosphoric acid) and ACN (47:53 v/v) at 1 mL/min and 25 degrees C. For detection, UV light at 227 nm was used. The derivatization conditions including reaction time, temperature, and concentration of TSIC were optimized. The calibration curves were linear from 0.062 to 18.6 microg/mL (r(2)= 0.9999) and from 0.071 to 21.3 microg/mL (r(2) = 0.9999) for DEG and PG, respectively. The RSD values of intra- and interday assays were all below 4% for DEG and PG. The proposed method was then successfully applied to analyze two Armillarisin A injection samples and two spiked syrup samples.     

Gas-chromatographic determination of propylene- and diethylene glycol ethers in urine

Summary In order to reduce the health risks in solvent technology, produced by the largely used ethylene glycol ethers, these are getting more and more substituted by glycol ethers derived from propylene glycol. According to the current knowledge these also called 1-alkoxy-2-propanols are to a considerable amount excreted unmetabolized in urine; so these substances themselves might be used for the estimation of health risks. The sensitive analysis consists of a special extraction step using diatomaceous earth. The extract is then concentrated for further gas-chromatographic investigation (FID). Using this technique, 17 in part widely used glycol ethers in urine were determined.     

气相色谱-质谱法快速测定牙膏中的二甘醇

建立了气相色谱-质谱法（GC-MS）快速测定牙膏中的二甘醇的方法。牙膏样品经三氯甲烷提取后,应用气相色谱-质谱联用仪,以选择离子监测（SIM）模式对其中的二甘醇进行分析。二甘醇的线性范围为21.24-1062 mg/L,线性相关系数（r）为0.9995;检出限和定量限分别为2.0、5.0 mg/L;高、中、低3种浓度下的回收率在88.51%-101.6%之间,相对标准偏差（RSD）在1.6%-8.11%之间;仪器对二甘醇的响应在24 h内保持稳定。     

Identification of diethylene glycol monobutyl ether as a source of contamination in an ion trap mass spectrometer

Tandem liquid chromatography-mass spectrometry coupled to online radioactive material detection (LC/RAM/MS/MS) is a technique that is used routinely for in vivo and in vitro drug metabolism studies and allows for a simultaneous correlation between radiochemical peaks and mass spectral data. The compound diethylene glycol monobutyl ether (DGBE), a component of a commercially available scintillation cocktail for RAM analysis, was identified as a source of overwhelming chemical noise in a mass spectrometer which was used in an LC/RAM/MS/MS configuration. In this report, we describe the identification of DGBE as the source of the chemical noise and the methods that were used to minimize the exposure of the mass spectrometer to volatile components of the scintillation cocktail.     

Ternary diffusion coefficients of diethylene glycol and lithium chloride in aqueous solutions containing diethylene glycol and lithium chloride

In this work, ternary diffusion coefficients of diethylene glycol and lithium chloride in aqueous solutions containing diethylene glycol and lithium chloride were reported for temperatures (303.2, 308.2, and 313.2 K) using the Taylor dispersion method. The investigated ternaries contained total glycol–salt concentrations of 10, 15, and 20 wt%. The main diffusion coefficients (D₁₁ and D₂₂) and the cross-diffusion coefficients (D₁₂ and D₂₁) were discussed as function of temperature and concentration. A modified equation originally proposed by Batchelor [1] for mixture of hard spheres in a continuum solvent was used to correlate the present diffusion coefficient data and the results are satisfactory.     

Catalysis of heteropoly acidic salts for synthesis of diethylene glycol ethyl ether with diethylene glycol and ethanol

Ag₃PW₁₂O₄₀ and Ag₄SiW₁₂O₄₀ showed high activity and stability in the synthesis of diethylene glycol ethyl ether with diethylene glycol and ethanol, on which the conversion is 80.2% and 78.4%, respectively, and the selectivity of diethylene glycol ether is 75.4% and 80.6%, respectively. After the third reaction cycle, Ag₃PW₁₂O₄₀ and Ag₄SiW₁₂O₄₀) still showed higher activity and selectivity, on which the conversion is 72. 6% and 77.5% respectively. But the activity of Ag₃PMo₁₂O₄₀ is lower, the conversion is only 21.0%. IR, XRD, TG and n‐butylamine titrimetry showed that the catalysis may be connected with two kinds of acidic centers owned by heteropoly acidic salt.     

LC-ESI-MS determination of diethylene glycol pollution in sea water samples collected around gas extraction platform plants

Produced formation waters (PFWs) represent the largest aqueous wastes that are normally discharged into the marine environment during the offshore gas production processes. The chemical additive diethylene glycol (DEG) is widely used in the gas production line and therefore can be found in the PFW, becoming of environmental concern. In this study, a new method has been developed for trace determination of DEG in sea water samples collected around offshore gas platforms. The method is based on liquid chromatography coupled to electrospray ionization mass spectrometry (LC-ESI-MS). Prior to analysis, water samples were derivatized using the Schotten-Baumann method for the benzoylation of glycols. The derivatization procedure allowed us to maximize the ESI-MS response of DEG and minimize the influence of interfering compounds. The method was validated and allowed a quantification of DEG in sea water samples with a method LOD of 0.4 ng/mL. The applicability of the procedure was demonstrated by analyzing sea water samples collected around eight gas platforms located in the Adriatic Sea (Italy).     

Quantitative analysis of pharmaceutical products by laser-induced breakdown spectroscopy

In this paper, the capabilities of laser-induced breakdown spectroscopy (LIBS) for rapid analysis of multi-component pharmaceutical tablets are illustrated using several examples. The atomic line emission from an element present only in a particular component of the tablet (for instance, emission of phosphorus from the drug, or of magnesium from the lubricant) enables the quantitative analysis of that component. It is also demonstrated that simple schemes can significantly improve the analytical performance of LIBS in this context. In particular, internal standardization with a carbon line was found to enable the correction of a matrix effect, apart from improving the precision of measurement. Furthermore, an improvement in the linearity of calibration was observed when the plasma continuum emission was used as internal standard. Finally, in the case of drugs containing halogen species (e.g. F or Cl), producing the plasma in a helium atmosphere caused a seven to eight-fold increase of the signal-to-background ratio, thus improving sensitivity. These data illustrate the strengths of LIBS for fast at-line assessment of the reliability of pharmaceutical manufacturing processes.     

Quantitation of diethylene glycol monoethyl ether in citrus oils

The use of diethylene glycol monoethyl ether as a flavor solvent is restricted. Since existing methods of quantitation are tedious or require sophisticated multi-dimensional GC instrumentation, a simple method has been developed using low cost GC-MS. Monitoring of ions 31 and 45 enables quantitation of DEGEE in essential oils at levels down to 1 μg/g with accuracy equal to or better than 15%.     

Crystallization of poly(diethylene glycol terephthalate)

The crystallization of a low molecular weight fraction of poly(diethylene glycol terephthalate) (PDET) was studied from the melt and from benzene, ethyl acetate and chlorobenzene. From the melt, crystallization does not occur, irrespective of the crystallization temperature. When PDET is crystallized from solutions in the three solvents, by isothermal growth at temperatures from 10 to 30°, crystals are obtained in the concentration range examined. Crystals were investigated by X-ray diffraction and by differential scanning calorimetry in order to measure the crystallinity, the melting points, glass transition and melting depression of mixtures of the polymer with solvents. Prior to crystallization, at given undercoolings and sufficient concentrations, gelation occurs due to microstructural heterogeneity.     

Preparation of copolymer microspheres of diethylene glycol dimethacrylate

Preparation of copolymer microspheres of diethylene glycol dimethacrylate (2G) with several comonomers by radiation-induced radical polymerization is described. Ethyl methacrylate (EMA), acrylamide, maleic anhydride, and styrene gave microspheres successively. The copolymerization resulted in gelation more easily than the 2G homopolymerization. The allowed ratio of copolymerization is up to about 0.4 as the mole fraction of comonomer for the solution containing 10 vol % 2G monomer. Copolymerization affected the size of microspheres by keeping its narrow distribution. The size of microspheres was increased by the copolymerization with EMA and styrene and, was decreased with acrylamide. The formation of microsphere strongly depends on the crosslinking ability of monomers. The crosslinking ability and reactivity in the copolymerization cause the change of the size of the microspheres. © 1992 John Wiley & Sons, Inc.     

Degradation mechanism of diethylene glycol units in a terephthalate polymer

Diethylene glycol (DEG) is incorporated into poly(ethylene terephthalate) (PET) during industrial synthesis in order to control crystallisation kinetics. DEG is known to be a weak point in the thermal degradation of PET, which is problematic during the recycling of the polymer.Studies on the thermal decomposition of the model polymer poly(diethylene glycol terephthalate) (PDEGT) have been performed using TG, DSC, TVA and spectroscopic techniques. They revealed a degradation behaviour with two distinct steps, where the first step initiates some 100 K below the degradation temperature of PET. The second step is similar to the behaviour of PET.Based on our observations, a new degradation mechanism specific to DEG units is proposed, where random ether groups along the backbone can back-bite and form cyclic oligomers. These cyclic species, containing ether moieties, are evolved at 245 °C and constitute the first of the two steps of degradation observed for PDEGT.     

Simultaneous liquid chromatographic determination of ezetimibe and simvastatin in pharmaceutical products

A reversed-phase liquid chromatographic (LC) method was developed and validated for the simultaneous determination of ezetimibe and simvastatin in pharmaceutical dosage forms. The LC method was carried out on a Synergi fusion C18 column (150 mm x 4.6 mm id) maintained at 45 degrees C. The mobile phase consisted of phosphate buffer 0.03 M, pH 4.5-acetonitrile (35 + 65, v/v) run at a flow rate of 0.6 mL/min, and detection was made using a photodiode array detector at 234 nm. The chromatographic separation was obtained within 15.0 min, and calibration graphs were linear in the concentration range of 0.5-200 microg/mL. Validation parameters such as specificity, linearity, precision, accuracy, and robustness were evaluated, giving results within the acceptable range for both compounds. Moreover, the proposed method was successfully applied for the routine quality control analysis of pharmaceutical products.     

Titrimetric determination of fluoride in some pharmaceutical products used for fluoridation

Two titrimetric methods were developed for the determination of fluoride contents in some pharmaceutical preparations used for fluoridation. One of the methods is catalytic controlled-current potentiometry involving two identical platinum indicator electrodes and thorium nitrate as titrant. The reaction between hydrogen peroxide and potassium iodide in the presence of acetate buffer (pH 3.6), which is catalysed by the excess of thorium nitrate, served for the end-point indication. The other method is the automatic potentiometric titration involving a fluoride-selective electrode and lanthanum nitrate as titrating agent. In both procedures, special attention was paid to sample pretreatment and to determination of optimal experimental conditions. Fluoride contents in the range 16-32 microg/ml are determined with a relative standard deviation less than 1.34%. The results are compared to those obtained by standard methods described in the United States Pharmacopeia XXI and recommended by the manufacturer of the preparations.