Fabrication and Optical Properties of Aligned Zn1-xMgxO Nanowire Arrays

Aligned Zn_1-xMg_xO nanowire arrays were successfully prepared on Si(111) substrates via the chemical vapor deposition (CVD) method with a mixture of ZnO, Mg, and activated carbon powders as reactants. The microstructures and optical properties of the synthesized Zn_1-xMg_xO nanowire arrays were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive analysis X-ray (EDAX), and photoluminescence (PL) spectrum analytic apparatus, respectively. While Mg content was achieved or less approximately 0.29 (x, atomic ratio) in ZnO lattice, the crystal lattice of the synthesized samples exhibited wurtzite structure. The Mg atoms were distributed into the ZnO crystal as the interstitial and displaced atoms, and there was no phase separation in preparing Zn_1-xMg_xO nanowire arrays. However, as the Mg content was up to 0.53 (x) in the fabricated Zn_1-xMg_xO samples, a clear phase separation phenomena appeared in the Zn_1-xMg_xO crystal. Compared with the PL spectrum of the pure ZnO nanowire arrays, the analytic results showed that a blue-shift of the near-band edge emission with increasing Mg content was observed in the Zn_1-xMg_xO arrays. And the relative intensities of green peak at ca 535 nm and UV emission peak at ca 376 nm were all restrained.     

Optical Properties of Mg x Zn1−x O Polycrystalline Thin Films Prepared by Sol-Gel Deposition Method

The Mg _x Zn_1–x O alloy thin films were synthesized on Si and quartz substrates by the sol-gel deposition method. The transmittance and cathodoluminescence spectra of the Mg_0.05Zn_0.95O and Mg_0.15Zn_0.85O nanoparticle films were obtained at room temperature. It was found that the bandgap of Mg_0.05Zn_0.95O and Mg_0.15Zn_0.85O films is as large as 3.72 eV and 3.79 eV, respectively. The ultraviolet emission peaks are located at 376 nm and 370 nm, respectively, for the samples annealed at 600°C. When the annealing temperature is elevated to 1000°C, the band-gap decreases to 3.42 eV and an emission line related to the deep-level defect appears at 500 nm. The mechanism behind these phenomena is discussed.     

Preparation and characterization of lithium ion-conducting glass-ceramics in the Li1 + xCrxGe2 − x(PO4)3 system

Li₂O–Cr₂O₃–GeO₂–P₂O₅ based glasses were synthesized by a conventional melt-quenching method and successfully converted into glass-ceramics through heat treatment. Experimental results of DTA, XRD, ac impedance techniques and FESEM indicated that Li_1.4Cr_0.4Ge_1.6(PO₄)₃ glass-ceramics treated at 900 °C for 12 h in the Li_1 + xCr_xGe_2 − x(PO₄)₃ (x = 0–0.8) system exhibited the best glass stability against crystallization and the highest ambient conductivity value of 6.81 × 10⁻⁴ S/cm with an activation energy as low as 26.9 kJ/mol. In addition, the Li_1.4Cr_0.4Ge_1.6(PO₄)₃ glass-ceramics displayed good chemical stability against lithium metal at room temperature. The good thermal and chemical stability, excellent conducting property, easy preparation and low cost make it promising to be used as solid-state electrolytes for all-solid-state lithium batteries.     

Anodic composite deposition of RuO2·xH2O–TiO2 for electrochemical supercapacitors

This communication demonstrates the first work on anodic composite deposition of oxide nanocomposites. Rutile TiO₂ nanoflowers with an average petal size of ca. 10 nm in diameter and 100 nm in length were synthesized from a TiCl₃ solution purged with air at 25 °C for 12 days prior to the composite deposition. Hydrous ruthenium oxide (RuO₂·xH₂O) and TiO₂ nanoflowers were composite-deposited onto Ti substrates for supercapacitors. In comparing with RuO₂·xH₂O deposits, RuO₂·xH₂O–TiO₂ nanocomposites with a highly porous nature exhibit the weakly mass-dependent specific capacitance and high-power capacitive characteristics.     

Effects of gold catalysts and thermal evaporation method modifications on the growth process of Zn1−xMgxO nanowires

In this paper, we investigate the roles of gold catalysts and thermal evaporation method modifications in the growth process of Zn_1−xMg_xO nanowires. Zn_1−xMg_xO nanowires are fabricated on silicon substrates with and without using a gold catalyst. Characterizations reveal that Mg acts in a self-catalyst role during the growth process of Zn_1−xMg_xO nanowires grown on catalyst-free substrate. The optical properties and crystalline quality of the Zn_1−xMg_xO nanowires are characterized by room temperature photoluminescence (PL) measurements and Raman spectroscopy, respectively. The Raman and PL studies demonstrate that the Zn_1−xMg_xO nanowires grown using the catalyst-free method have good crystallinity with excellent optical properties and have a larger band-gap in comparison to those grown with the assistance of gold.     

Synthesis of visible-light reactive TiO2−xNy photocatalyst by mechanochemical doping

Yellowish TiO_2−xN_y was prepared by a novel mechanochemical nitrogen-doping method. The samples were prepared by a high-energy ball milling of P25 titania with different nitrogen sources such as hexamethylenetetramine, urea or ammonium carbonate, followed by calcination in air at 400 °C. The high mechanical energy accelerated the phase transformation of anatase to rutile, while the existence of the nitrogen reagents tended to block the transformation. The calcination treatment slightly increased the crystallinity of the prepared titania. The prepared powders possessed two absorption edges at around 400 and 540 nm and showed an excellent photocatalytic ability for the oxidation of nitrogen monoxide under visible light irradiation. Under the irradiation of visible light with wavelengths of >510 nm, nitrogen monoxide could be continuously removed by the nitrogen doped titania prepared from the P25 titania-hexamethylenetetramine mixture, while the powders prepared using urea and ammonium carbonate as nitrogen sources showed lower activities. This mechanochemical technique might be widely useful for doping oxides with nonmetallic elements.     

Effects of Mg doping on the properties of highly transparent conductive and near infrared reflective Zn1−xMgxO:Ga films

Highly transparent conductive and near infrared (IR) reflective Gallium-doped ZnMgO (Zn_1−xMg_xO:Ga) films with Mg content from 0 to 10 at% were deposited on glass substrate by DC reactive magnetron sputtering. X-ray diffraction shows all the ZnMgO:Ga films are polycrystalline and have wurtzite structure with a preferential c-axis orientation. Hall measurements indicate that the resistivity of these films obviously increases with the Mg concentration increasing. The average transmittance of Zn_1−xMg_xO:Ga films is over 90% in the visible range. All the Zn_1−xMg_xO:Ga films have low transmittance and high reflectance in the IR region.     

空气中合成固溶体荧光粉Ba_2(Zn,Mg)Si_2O_7∶Eu~(2+),Eu~(3+),Ce~(3+)及其发光特性

采用高温固相法在空气中合成了Ba1.97-yZn1-xMgxSi2O7∶0.03Eu,y Ce3+系列荧光粉。分别采用X-射线衍射和荧光光谱对所合成荧光粉的物相和发光性质进行了表征。在紫外光330~360 nm激发下,固溶体荧光粉Ba1.97-yZn1-xMgxSi2O7∶0.03Eu的发射光谱在350~725 nm范围内呈现多谱峰发射,360和500 nm处有强的宽带发射属于Eu2+离子的4f 65d1-4f 7跃迁,590~725 nm红光区窄带谱源于Eu3+的5D0-7FJ(J=1,2,3,4)跃迁,这表明,在空气气氛中,部分Eu3+在Ba1.97-yZn1-xMgxSi2O7基质中被还原成了Eu2+;当x=0.1时,荧光粉Ba1.97Zn0.9Mg0.1Si2O7∶0.03Eu的绿色发光最强,表明Eu3+被还原成Eu2+离子的程度最大。当共掺入Ce3+离子后,形成Ba1.97-yZn0.9Mg0.1Si2O7∶0.03Eu,y Ce3+荧光粉体系,其发光随着Ce3+离子浓度的增大由蓝绿区经白光区到达橙红区;发现名义组成为Ba1.96Zn0.9Mg0.1Si2O7∶0.03Eu,0.01Ce3+的荧光粉的色坐标为(0.323,0.311),接近理想白光,是一种有潜在应用价值的白光荧光粉。讨论了稀土离子在Ba2Zn0.9Mg0.1Si2O7基质中的能量传递与发光机理。     

Cathodic deposition of ternary In+As+Sb alloys and formation of InAsxSb1−x

In+As+Sb alloys have been deposited onto Ni and Ti cathodes from tartaric acid solutions at pH 2. Homogeneous deposits of composition suitable for achieving InAs_xSb_1−x can be obtained from this medium. The As-to-Sb ratio can be controlled by properly selecting solution composition and deposition potential.X-ray photoelectron spectroscopy and X-ray diffraction analyses show that formation of III–V compounds occurs at room temperature. In reacts preferentially with As rather than with Sb, but crystalline phases formed at room temperature are Sb-rich. After annealing the In+As+Sb alloys at 250°C, the composition calculated from cell parameters appears similar to that measured by energy-dispersive X-ray analysis, suggesting that the entire deposit has been converted into the InAs_xSb_1−x crystalline phase.     

A TEM, XRD, and crystal chemical investigation of oxygen/vacancy ordering in (Ba1−xLax)2In2O5+x, 0x0.6

A careful TEM and XRD study of the (Ba_1−xLa_x)₂In₂O_5+x, 0x0.6, ‘defect-perovskite’-type solid solution has been carried out. A well-defined structural phase transition is shown to occur between x=0.1 and 0.2 from the orthorhombic brownmillerite structure type on the low x side to a multiple twinned, tetragonal 1×1×2 perovskite-related superstructure phase on the high x side at x=0.2. This phase transition correlates with an important phase transition previously observed in electrical conductivity versus temperature measurements. The existence of additional satellite reflections close to the regions of reciprocal space was found to be typical of all (Ba_1−xLa_x)₂In₂O_5+x specimens, although their intensity relative to the parent Bragg reflections systematically reduces as x increases. As x increases beyond 0.2, the -type satellite reflections initially become weaker and rather more diffuse for x=0.3 before splitting into pairs of rather weak and somewhat diffuse incommensurate satellite reflections for x=0.4 and beyond. An interpretation in terms of oxygen vacancy ordering and associated structural relaxation is given. Additional structured diffuse scattering is also observed and a tentative explanation in terms of Ba/La ordering and associated local strain distortions put forward.     

Photoluminescence properties of La(PO3)3:Tb under VUV excitation

La_1−x(PO₃)₃:Tb_x³⁺ (0<x0.6) were prepared using solid-state reaction. The vacuum ultraviolet (VUV) excitation spectrum of La_0.55(PO₃)₃:Tb_0.45³⁺ indicates that the absorption of (PO₃)₃³⁻ groups locates at about 163 and 174 nm and the absorption bands of (PO₃)₃³⁻ groups (174 nm) and La³⁺–O²⁻ (200 nm) and Tb³⁺ (213 nm) overlap each other. These results imply that the (PO₃)₃³⁻ groups can efficiently absorb the excited energy around 172 nm and transfer the energy to Tb³⁺. Under 172 nm excitation, the optimal photoluminescence (PL) intensity is obtained when Tb concentration reaches 0.45 and is about 71% of commercial phosphor Zn_1.96SiO₄:0.04 Mn²⁺ with chromaticity coordinates of (0.343, 0.578) and the decay time of about 4.47 ms.     

空气中合成固溶体荧光粉Ba2(Zn, Mg)Si2O7:Ce3+,Eu2+,Eu3+及其发光特性

采用高温固相法在空气中合成了Ba_1.97-yZn_1-xMg_xSi₂O₇:0.03Eu,yCe³⁺系列荧光粉。分别采用X-射线衍射和荧光光谱对所合成荧光粉的物相和发光性质进行了表征。在紫外光330~360 nm激发下,固溶体荧光粉Ba_1.97-yZn_1-xMg_xSi₂O₇:0.03Eu的发射光谱在350~725 nm范围内呈现多谱峰发射,360和500 nm处有强的宽带发射属于Eu²⁺离子的4f⁶5d¹-4f⁷跃迁,590~725 nm红光区窄带谱源于Eu³⁺的⁵D₀-⁷F_J (J=1,2,3,4)跃迁,这表明,在空气气氛中,部分Eu³⁺在Ba_1.97-yZn_1-xMg_xSi₂O₇基质中被还原成了Eu²⁺;当x=0.1时,荧光粉Ba_1.97Zn_0.9Mg_0.1Si₂O₇:0.03Eu的绿色发光最强,表明Eu³⁺被还原成Eu²⁺离子的程度最大。当共掺入Ce³⁺离子后,形成Ba_1.97-yZn_0.9Mg_0.1Si₂O₇:0.03Eu,yCe³⁺荧光粉体系,其发光随着Ce³⁺离子浓度的增大由蓝绿区经白光区到达橙红区;发现名义组成为Ba_1.96Zn_0.9Mg_0.1Si₂O₇:0.01Ce³⁺,0.03Eu的荧光粉的色坐标为(0.323,0.311),接近理想白光,是一种有潜在应用价值的白光荧光粉。讨论了稀土离子在Ba₂Zn_0.9Mg_0.1Si₂O₇基质中的能量传递与发光机理。     

The Phase Relations in the System In2O3–TiO2–MgO at 1100 and 1350°C

The phase relations in the system In₂O₃–TiO₂–MgO at 1100 and 1350°C are determined by a classical quenching method. In this system, there are four pseudobinary compounds, In₂TiO₅, MgTi₂O₅ (pseudobrookite type), MgTiO₃ (ilmenite type), and Mg₂TiO₄ (spinel type) at 1100°C. At 1350°C, in addition to these compounds there exist a spinel-type solid solution Mg_2−xIn_2xTi_1−xO₄ (0≤x≤1) and a compound In₆Ti₆MgO₂₂ with lattice constants a=5.9236(7) Å, b=3.3862(4) Å, c=6.3609(7) Å, β=108.15(1)°, and q=0.369, which is isostructural with the monoclinic In₃Ti₂FeO₁₀ in the system In₂O₃–TiO₂–MgO. The relation between the lattice constants of the spinel phase and the composition nearly satisfies Vegard's law. In₆Ti₆MgO₂₂ extends a solid solution range to In₂₀Ti₁₇Mg₃O₆₇ with lattice constants of a=5.9230(5) Å, b=3.3823(3) Å, c=6.3698(6) Å, β=108.10(5)°, and q=0.360. The distributions of constituent cations in the solid solutions are discussed in terms of their ionic radius and site preference effect.     

Analysis of structural and magnetic phase transition behaviors of La1−xSrxCrO3 by measurement of heat capacity with thermal relaxation technique

The heat capacity, C_p, of the La_1−xSr_xCrO₃ system and its temperature dependence have been measured by a thermal relaxation technique. Both structural and magnetic phase transitions were detected at temperatures that can be surmised from the phase diagram proposed in previous studies. The observed variation in enthalpy after the first-order structural phase transition, ΔH, showed agreement with those measured by differential scanning calorimetry (DSC). A decrease in the variation in C_p in the second-order magnetic phase transition, ΔC_p, with an increase in Sr content was detected, which can be attributed to a decrease in electronic spin configuration entropy with an increase in Sr content. In the dependence of ΔC_p on Sr content, a bending point was also observed at x  0.12, at which the crystal system varies from an orthorhombic-distorted perovskite structure to a rhombohedral-distorted perovskite structure.     

Conductivity studies of dense yttrium-doped BaZrO3 sintered at 1325 °C

High-temperature proton conductors have wide applications in the areas of fuel cells, electrolysis and hydrogen separation. Barium zirconate-based materials are of interest due to their good stability and high protonic conductivity. The reported conductivity of these ceramic materials is generally less than 10⁻² S/cm, even at high temperatures. This is not high enough for an electrolyte-supported device to achieve an ASR of less than 0.2 Ω cm² therefore thin film electrolytes are required for successful application. As BaZrO₃-based materials have to be sintered at temperatures as high as 1700 °C, this makes it difficult to find a suitable supporting electrode which will not undergo significant chemical reaction with the BaZrO₃-based electrolyte during fabrication of the required electrode supported electrolyte. In this paper, proton-conducting BaZr_0.8Y_0.2O_2.9 was successfully sintered at 1325 °C with a relative density of 96% via addition of 1 wt% ZnO. Fabrication of electrochemical cells using proton-conducting BaZr_0.8Y_0.2O_2.9 as the electrolyte thus becomes possible. The formula of the 1 wt% ZnO added sample is Ba_0.97Zr_0.77Y_0.19Zn_0.04O_3−δ which exhibits a tetragonal structure with space group P4/mbm (127); a=5.9787(1) Å, c=4.2345(1) Å, V=151.36(1) Å³. It was found that a solid solution was formed for a limited range of Zn doping. Conductivity has been studied as a function of atmosphere (air, dry and wet 5% H₂/Ar) with the changes in bulk and grain boundary on changing atmosphere being monitored as a function of time. The total conductivity of Ba_0.97Zr_0.77Y_0.19Zn_0.04O_3–δ is 1.0×10⁻³ S/cm above 600 °C therefore it may be used as a proton-conducting thin film electrolyte for efficient electrochemical devices at such temperatures. The grain boundary resistance is insignificant at high temperature for the well-sintered sample.     

The metastable Ni7±xS6, and mixed Ni6±x(S1−ySey)5, phases

The closely related, narrowly non-stoichiometric, metastable as well as thermodynamically stable “phases” in the metal-rich part of the Ni–S phase diagram near the nominal composition Ni_7±xS₆ have been carefully re-investigated via electron diffraction and transmission electron microscope imaging. Two quite distinct polymorphs have been identified, a minority incommensurate interface-modulated polymorph and a (heavily twinned) majority I1a1, a=2a_p, b=2b_p, c=−a_p+c_p superstructure (of an underlying Bmmb, a_p3.3, b_p16.4, c_p11.3 Å parent structure) polymorph. The incommensurate polymorph is shown to be very closely related to the only known polymorph of Ni_6±xSe₅ and is rapidly stabilized to room temperature upon doping of the sulfide compounds with selenium.     

Characteristics of Au/MgxAlO hydrotalcite catalysts in CO selective oxidation

Gold catalysts, supported on a solid base of Mg_xAlO hydrotalcite, were prepared by a modified deposition precipitation method for CO selective oxidation. The preparation parameters and pretreatment of the catalysts were investigated. The pH and the HAuCl₄ concentration in the initial solution, and the Mg/Al molar ratio of Mg_xAlO affected the pH in the final solution and determined the actual gold loading of the catalyst. The calcination temperatures of the Mg_xAlO support and the Au/Mg_xAlO catalyst dominated the Au³⁺/Au⁰ ratio on the catalyst. The pretreatment of the catalyst as well as the gold loading and the Au³⁺/Au⁰ ratio, critically determined the activity of the catalyst for CO selective oxidation. Based on XPS and in situ DR-FTIR analyses, a mechanism for CO selective oxidation on 2%Au/Mg₂AlO was proposed. The hydroxyl group on Mg₂AlO also participated in the reaction.     

High performance protonic ceramic membrane fuel cells (PCMFCs) with Ba0.5Sr0.5Zn0.2Fe0.8O3−δ perovskite cathode

Protonic ceramic membrane fuel cells (PCMFCs) based on proton-conducting electrolytes have attracted much attention because of many advantages, such as low activation energy and high energy efficiency. BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY7) electrolyte based PCMFCs with stable Ba_0.5Sr_0.5Zn_0.2Fe_0.8O_3−δ (BSZF) perovskite cathode were investigated. Using thin membrane BZCY7 electrolyte (about 15 μm in thickness) synthesized by a modified Pechini method on NiO-BZCY7 anode support, PCMFCs were assembled and tested by selecting stable BSZF perovskite cathode. An open-circuit potential of 1.015 V, a maximum power density of 486 mW cm⁻², and a low polarization resistance of the electrodes of 0.08 Ω cm² was achieved at 700 °C. The results have indicated that BZCY7 proton-conducting electrolyte with BSZF cathode is a promising material system for the next generation solid oxide fuel cells.     

Properties of the perovskites, SrMn1−xFexO3−δ (x=1/3, 1/2, 2/3)

The SrMn_1−xFe_xO_3−δ (x=1/3, 1/2, 2/3) phases have been prepared and are shown by powder X-ray and neutron (for x=1/2) diffraction to adopt an ideal cubic perovskite structure with a disordered distribution of transition-metal cations over the six-coordinate B-site. Due to synthesis in air, the phases are oxygen deficient and formally contain both Fe³⁺ and Fe⁴⁺. Magnetic susceptibility data show an antiferromagnetic transition at 180 and 140 K for x=1/3 and 1/2, respectively and a spin-glass transition at 5, 25, 45 K for x=1/3, 1/2 and 2/3, respectively. The magnetic properties are explained in terms of super-exchange interactions between Mn⁴⁺, Fe^(4+δ)+ and Fe⁽³⁺⁾⁺. The XAS results for the Mn-sites in these compounds indicate small Mn-valence changes, however, the Mn-pre-edge spectra indicate increased localization of the Mn-e_g orbitals with Fe substitution. The Mössbauer results show the distinct two-site Fe⁽³⁺⁾+/Fe^(4+δ)+ disproportionation in the Mn- substituted materials with strong covalency effects at both sites. This disproportionation is a very concrete reflection of a localization of the Fe-d states due to the Mn-substitution.     

Analysis of thermo-magnetic fluctuations above the glass-transition temperature in Bi1.6Pb0.5Sr2−xEuxCa1.1Cu2.1O8+δ (0.000 ≤ x ≤ 0.180) system

The resistivity of Bi_1.6Pb_0.5Sr_2−xEu_xCa_1.1Cu_2.1O_8+δ (0.000 ≤ x ≤ 0.180) superconductor has been measured as a function of temperature and magnetic field. The resistivity shows a glassy behavior even at higher temperatures and magnetic fields for the Eu-doped samples as compared with the Eu free sample. The values of glass-transition temperature [T_g], magnetic field dependent activation energy [U₀(B)] and the temperature and magnetic field dependent activation energy [U₀(B,T)] are found to be maximum for optimal doping levels (x = 0.135) which shows that the flux lines are effectively pinned in this sample. Also for temperatures below the superconducting transition temperature (T_C), a scaling of measured resistivity curves in magnetic field (B = 0.4 and 0.8 T) is obtained and this scaling is quite useful for better understanding of the behavior of the flux vortices in high temperature superconductors.