Isothermal melt-crystallization and melting behavior for three linear aromatic polyesters

Isothermal crystallization and subsequent melting behavior for three different types of linear aromatic polyester, namely poly(ethylene terephthalate) (PET), poly(trimethylene terephthalate) (PTT), and poly(butylene terephthalate) (PBT), were investigated (with an emphasis on PTT in comparison with PET and PBT). These polyesters were different in the number of methylene groups (i.e. 2, 3, and 4 for PET, PTT, and PBT, respectively). Isothermal crystallization studies were carried out in a differential scanning calorimeter (DSC) over the crystallization temperature range of 182-208 °C. The wide-angle X-ray diffraction (WAXD) technique was used to obtain information about crystal modification and apparent degree of crystallinity. The kinetics of the crystallization process was assessed by a direct fitting of the experimental data to the Avrami, Tobin, and Malkin macrokinetic models. It was found that the crystallization rates of these polyesters were in the following order: PBT>PTT>PET, and the melting of these polyesters exhibited multiple-melting phenomenon. Lastly, the equilibrium melting temperature for these polyesters was estimated based on the linear and non-linear Hoffman-Weeks (LHW and NLHW) extrapolative methods.     

Calorimetric study of blends of poly(butylene terephthalate) and liquid crystalline copolyester

A calorimetric study of blends of poly(ethylene terephthalate-co-p-oxybenzoate), PET/PHB, with poly(butylene terephthalate), PBT has been carried out in the form of as-spun and drawn fibres. DSC melting and crystallization results show that PBT is compatible with LCP and the crystallization of PBT decreases by the addition of LCP in the matrix. The crystallization behaviour of blend fibres is investigated as a function of temperature of crystallization. A detailed analysis of the crystallization course has been made utilizing the Avrami expression. The isothermal calorimetric measurements provide evidence of decrease of rate of crystallization of PBT on addition of the liquid crystalline component up to about 50% by weight. The values of the Avrami exponents change in the temperature range from 200° to 215°C. Dimensionality changes in crystallization could be due to LCP mesophase-transition.     

Block copolymers of poly(ethylene terephthalate)-poly(butylene terephthalate). II. Small-angle light-scattering studies

Small-angle light-scattering (SALS) studies were carried out on block copolymers of poly(ethylene terephthalate) (PET) and poly(butylene terephthalate) (PBT), the synthesis and characterization of which have been reported in an earlier paper. Samples were crystallized isothermally from the melt at 95°C for predetermined crystallization times in order to follow the formation and growth of crystalline superstructure. During the early stages of crystallization, the block copolymers showed unusual H_v patterns with the four lobes along the polarizer directions, while at later stages they showed the usual H_v patterns with the four lobes at 45° to the polarizer directions. The unusual patterns are characteristic of PBT superstructure, while the usual patterns are characteristic of PET superstructure. These results show that PBT, which is the faster-crystallizing component, crystallizes first and provides nucleation sites for the crystallization of PET, which crystallizes later. Similar behavior was not observed in PET homopolymer and random copolymers of equivalent compositions. In each case the spherulite size increased with the time of crystallization. The ultimate spherulite size decreased with increasing PBT content in the block copolymer, thus showing an increase in nucleation density. It was demonstrated that light scattering is a useful tool to characterize block copolymers of two crystalline components which have different types of superstructure.     

Relationships between the molecular architecture,crystallization capacity,and miscibility in poly(butylene terephthalate)/polycarbonate blends: A comparison with poly(ethylene terephthalate)/polycarbonate blends

Poly(butylene terephthalate) (PBT)/polycarbonate (PC) samples, prepared via reactive blending in the presence of Ti‐ and Sm‐based catalysts, resulted in block copolymers whose block length decreased as the mixing time increased. A single homogeneous amorphous phase occurred when the blocks had monomeric sequences shorter than 10 units. Otherwise, a crystalline phase of PBT developed. Also, in poly(ethylene terephthalate) (PET)/PC blends previously studied, the miscibility was strictly correlated with the crystallizability of the system. Therefore, the miscibility of the PBT/PC and PET/PC blends was compared with respect to the tendency of the PBT and PET blocks to crystallize under isothermal conditions. The crystallization rate of the PBT/PC copolymers was faster than that of the PET/PC copolymers with similar block lengths. Accordingly, the minimum crystallizable sequence length of the PBT blocks was shorter than that of the PET blocks (18 vs 31 monomeric unit sequences). This behavior was interpreted as an effect of the more flexible PBT units, which had a greater tendency to fold and crystallize than the PET units. Therefore, PBT, the blocks of which tended to crystallize even if they were very short and phase‐separated, was characterized by a poorer compatibility with PC than that of PET. As a result, the block size had a fundamental role in determining the crystallizability and, therefore, phase behavior of the semicrystalline block copolymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2821–2832, 2004     

Isothermal crystallization kinetics of PEO in poly(ethylene terephthalate)–poly(ethylene oxide) segmented copolymers. I. Effect of the soft‐block length

The isothermal crystallization kinetics of poly(ethylene oxide) (PEO) block in two poly(ethylene terephthalate) (PET)–PEO segmented copolymers was studied with differential scanning calorimetry. The Avrami equation failed to describe the overall crystallization process, but a modified Avrami equation, the Q equation, did. The crystallizability of the PET block and the different lengths of the PEO block exerted strong influences on the crystallization process, the crystallinity, and the final morphology of the PEO block. The mechanism of nucleation and the growth dimension of the PEO block were different because of the crystallizability of the PET block and the compositional heterogeneity. The crystallization of the PEO block was physically constrained by the microstructure of the PET crystalline phase, which resulted in a lower crystallization rate. However, this influence became weak with the increase in the soft‐block length. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3230–3238, 2000     

Syntheses of random PET‐co‐PTTs and some related copolyesters by entropically‐driven ring‐opening polymerizations and by melt blending: Thermal properties and crystallinity

A library of random poly(ethylene terephthalate) (PET), poly(trimethylene terephthalate) (PTT), and seven PET–PTT copolymers has been prepared in a high throughput manner by entropically‐driven ring‐opening polymerizations of the corresponding macrocyclic oligomers. The products have been investigated by differential scanning calorimetry and wide angle X‐ray diffraction. They show that the 50:50 copolymer displays a crystalline phase. The same phase can be formed by in situ transesterification when a 50:50 mixture of PET and PTT is melt blended. Poly(butylene terephthalate) (PBT)–PET and PTT–PBT 50:50 copolymers also show crystal phases. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Thermal properties of multiblock thermoplastic elastomerswith oligoamide soft blocks derived from dimerized fatty acid

Two series of multiblock copolymers, poly(ester-block-amide)s (PEA) and poly(amide-block-amide)s (PAA), with the same type of oligoamide soft block were obtained. Oligoamide soft block was prepared from dimerized fatty acid and 1,6-hexamethylenediamine. Oligo(butylene terephthalate) (PBT) was used as oligoester hard block in the first series and oligolaurolactam (PA12) was oligoamide hard block in the second one. The thermal and mechanical properties of these copolymers have been investigated as functions of temperature and the hard/soft block ratio. DSC and DMTA revealed that the copolymers behaved as thermoplastic elastomers.     

Synthesis and non‐isothermal crystallization kinetics of poly(ethylene terephthalate)‐co‐poly(propylene glycol) copolymers

Poly(ethylene terephthalate)‐co‐poly(propylene glycol) (PET‐co‐PPG) copolymers with PPG ratio ranging from 0 to 0.90 mol% were synthesized by the melt copolycondensation. The intrinsic viscosity, structure, non‐isothermal crystallization behavior, nucleation and spherulitic growth of the copolymers were investigated by Ubbelohde viscometer, Proton Nuclear Magnetic Resonance (¹H‐NMR), differential scanning calorimetry, and polarized optical microscopy, respectively. The non‐isothermal crystallization process of the copolymers was analyzed by Avrami, Ozawa, Mo's, Kissinger, and Dobreva methods, respectively. The results showed that the crystallizability of PET was apparently enhanced with incorporating a small amount of PPG, which first rose and then reduced with increasing amount of PPG in the copolymers at a given cooling rate. The crystallization mechanism was a three‐dimensional growth with both instantaneous and sporadic nucleation. Particularly, PET‐co‐PPG containing 0.60 mol% PPG exhibited the highest crystallizability among all the copolymers. Copyright © 2015 John Wiley & Sons, Ltd.     

Preparation and characterization of poly(butylene terephthalate)/poly(ethylene terephthalate) copolymers via solid‐state and melt polymerization

To increase the T_g in combination with a retained crystallization rate, bis(2‐hydroxyethyl)terephthalate (BHET) was incorporated into poly(butylene terephthalate) (PBT) via solid‐state copolymerization (SSP). The incorporated BHET fraction depends on the miscibility of BHET in the amorphous phase of PBT prior to SSP. DSC measurements showed that BHET is only partially miscible. During SSP, the miscible BHET fraction reacts via transesterification reactions with the mobile amorphous PBT segments. The immiscible BHET fraction reacts by self‐condensation, resulting in the formation of poly(ethylene terephthalate) (PET) homopolymer. ¹H‐NMR sequence distribution analysis showed that self‐condensation of BHET proceeded faster than the transesterification with PBT. SAXS measurements showed an increase in the long period with increasing fraction BHET present in the mixtures used for SSP followed by a decrease due to the formation of small PET crystals. DSC confirmed the presence of separate PET crystals. Furthermore, the incorporation of BHET via SSP resulted in PBT‐PET copolymers with an increased T_g compared to PBT. However, these copolymers showed a poorer crystallization behavior. The modified copolymer chain segments are apparently fully miscible with the unmodified PBT chains in the molten state. Consequently, the crystal growth process is retarded resulting in a decreased crystallization rate and crystallinity. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 882–899, 2007.     

PET,PBT结晶过程Avrami方程的探讨

用解偏振光法研究了PET,PBT以及PET-PBT,PBT-PBI共聚物在不同条件下的等温结晶过程.结果表明,Avrami指数n值和结晶速度常数随条件不同呈明显规律变化,且n值在绝大多数情况下不成整数.由此提出了这样的假设:n值是一个与晶核中结晶生长点数目相关的参数.     

聚对苯二甲酸乙二醇酯/聚乙二醇醚插层嵌段共聚物的结晶性能

合成了不同用量、不同分子量的聚乙二醇醚(PEG)或聚丁二醇醚(PTMC)与聚对苯二甲酸乙二醇酯(PET)/蒙脱土(MMT)的嵌段共聚物。研究了MMT在共聚物中的分散状态及PEG或PTMG对PET/MMT插层聚合物结晶性能的影响。结果表明,MMT在共聚物中以纳米尺寸分散;加入PEG或PTMG增强了聚酯链段的柔顺性,使共聚物熔体降温过程的结晶温度提高,冷结晶温度降低,即插层嵌段共聚物的结晶速率提高;在合成的共聚物中,分子量为2000,用量为DMT的6%的PEG对插层共聚物结晶速率的促进作用最大     

Heterogeneous nucleation on the crystallization poly(ethylene terephthalate)

The crystallization behavior of poly(ethylene terephthalate) (PET) with disodium terephthalate (DST) as nucleating agent was investigated. A detailed analysis of the crystallization course from the melt was made with the Avrami expression. The results demonstrated that DST additive can promote the PET crystallization rate in its entire crystallizable temperature range, and the acceleration degree of DST decreases with increasing temperature after a temperature higher than 180 °C. The values of the Avrami exponent indicated that the crystallization mode in Avrami theory is not suitable for the crystallization of these polymers, and the mechanism of the heterogeneous nucleation on PET crystallization is discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2135–2144, 2003     

Isothermal crystallization kinetics and melting behaviour of PET/ATO nanocomposites prepared by in situ polymerization

Neat poly(ethylene terephthalate) (PET) and PET/antimony doped tin oxide (ATO) nanocomposites were prepared by in situ polymerization. The study of the isothermal crystallization behaviors of neat PET and PET/ATO nanocomposites was carried out using differential scanning calorimetry (DSC). The crystallization kinetics under isothermal conditions could be described by the Avrami equation. For neat PET and PET/ATO nanocomposites, the Avrami exponent n both decreased with increasing crystallization temperature. In addition, for the same crystallization temperature, the value of n increased with increasing ATO content. These suggested that the crystallization types related to the values of n in the Avrami theory could not be suitable for the crystallization of PET and its nanocomposites. The change of the n values indicated that the addition of ATO resulted in the increase of the crystallizing growth points. That is a heterogeneous nucleating effect of ATO on crystallization of PET. In the DSC scan after isothermal crystallization process, multiple melting behavior was found. And the multiple endotherms could be attributed to melting of the recrystallized materials or the secondary lamellae produced during different crystallization processes. The equilibrium melting temperature of PET in the nanocomposites increased with increasing the ATO content. Surface free energy of PET chain folding for crystallization of PET/ATO nanocomposites was lower than that of neat PET, confirming the heterogeneous nucleation effect of ATO.     

Isothermal crystallization studies of poly(butylene terephthalate) composites

Different crystallization kinetic models (Avrami and Tobin) have been applied to study the crystallization kinetics of virgin poly(butylene terephthalate) (PBT) and filled PBT systems under isothermal experimental conditions. The experimental data have been analyzed with a nonlinear, multivariable regression program. The kinetic parameters for the isothermal crystallization have been determined. The analysis results indicate that both models satisfactorily represent the isothermal crystallization kinetics. PBT crystallizes most slowly. The presence of nanoclays or nanofibers, added as fillers, enhances the crystallization rate of PBT composites. An analysis of the kinetic data with the Avrami and Tobin models has shown little change in the crystallization exponent compared with that of virgin PBT. The crystallization rate constant decreases with a rise in the temperature for the two models. This trend has been observed for similar polyester systems reported in the literature. The dispersion of the clay layers in the PBT nanocomposites has been characterized with wide‐angle X‐ray diffraction and transmission electron microscopy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1344–1353, 2007     

Melt-crystallization behavior and isothermal crystallization kinetics of crystalline/crystalline blends of poly(ethylene terephthalate)/poly(trimethylene terephthalate)

The melt-crystallization and isothermal melt-crystallization kinetics of poly(ethylene terephthalate)/poly(trimethylene terephthalate) blends (PET/PTT) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy. Although PET and PTT in the binary blends are miscible at amorphous state, they will crystallize individually when cooled from the melt. In the DSC measurements, PET component with higher supercooling degree will crystallize first, and then the crystallite of PET will be the nucleating agent for PTT, which induce the crystallization of PTT at higher temperature. On the other hand, in both blends of PET80/PTT20 and PET60/PTT40, the PET component will crystallize at higher temperature with faster crystallization rate due to the dilute effect of PTT. So the commingled minor addition of one component to another helps to improve the crystallization of the blends. For blends of PET20/PTT80 and PET40/PTT60, isothermal crystallization kinetics evaluated in terms of the Avrami equation suggest different crystallization mechanisms occurred. The more PET content in blends, the fast crystallization rate is. The Avrami exponent, n = 3, suggests a three-dimensional growth of the crystals in both blends, which is further demonstrated by the spherulites formed in all blends. The crystalline blends show multiple-melting peaks during heating process.     

Copolymers of PBT and nylon 4T

Polybutylene terephthalate–nylon 4T copolymers (PBT–PA 4T) are synthesized from the diamide of diaminobutane and dimethyl terephthalate (DMT) with butane diol and more DMT in a concentration range of up to 50% PA 4T. The polymerization conditions were similar to those for PBT: first, a melt polymerization, followed by solid-state post-condensation. The materials were studied by differential scanning analysis (DSC) (melting and crystallization behavior) and dynamic mechanical thermal analysis (DMTA) (glass transitions and torsion moduli). The water absorptions were determined at 100% RH. By increasing the PA 4T content in the copolymers, melting temperatures increased strongly, heats of fusion decreased slightly, and glass transition temperatures increased linearly. The torsion moduli above the glass transition temperature were higher. © 1993 John Wiley & Sons, Inc.     

PBT-PA6嵌段共聚物中嵌段间的相容性

用热分析、动态粘弹谱、红外光谱和小角X光散射的实验结果,证实了在聚对苯二甲酸丁二酯-聚己内酰胺嵌段共聚物(简称PBT-PA_6)的无定形区中,两嵌段间具有良好的相容性,两嵌段间有氢键生成。     

Transesterification and crystallization behavior of poly(butylene succinate)/poly(butylene terephthalate) block copolymers

The block copolymers of poly(butylene succinate) (PBS) and poly(butylene terephthalate) (PBT) were synthesized by melt processing for different times. The sequence distribution, thermal properties, and crystallization behavior were investigated over a wide range of compositions. For PBS/PBT block copolymers it was confirmed by statistical analysis from ¹H-NMR data that the degree of randomness (B) was below 1. The melting peak (T_m) gradually moved to lower temperature with increasing melt processing time. It can be seen that the transesterification between PBS and PBT leads to a random copolymer. From the X-ray diffraction diagrams, only the crystal structure of PBS appeared in the M1 copolymer (PBS 80 wt %) and that of PBT appeared in the M3 (PBS 50 wt %) to M5 (PBS 20 wt %) copolymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 147–156, 1998     

Crystallization of polypropylene,nylon-66 and poly(ethylene terephthalate) at pressures to 200 MPa: Kinetics and characterization of products

The crystallization kinetics of polypropylene (PP), polyamide (PA66), and poly(ethylene terephthalate) (PET) were studied, using a pressure dilatometer (to 200 MPa) to follow the volume changes associated with the crystallization process. The commonly used Avrami equation fitted the isothermal/isobaric crystallization data of PP and PA66 well. The Avrami exponent n was between 1.3 and 1.7, independent of crystallization pressure and temperature. Lines of constant Avrami rate parameter Z in the P-T plane were essentially parallel to the pressure dependence of the melting points and crystallization temperatures. However, the Avrami equation was not suitable for PET. The Malkin, Dietz, and Kim equations provided better fits. The crystallization half-time of PET increased with pressure at constant supercooling, in contrast to PP and PA66, for which it remained essentially unchanged. X-ray diffraction, differential scanning calorimetry, and pressure dilatometry were used to study the effect of formation pressure on the crystal structure, the melting point, and the density of products which were crystallized for short times (minutes) at various temperatures and pressures. No new crystal structures were found for PA66 and PET, but a mixture of monoclinic and triclinic crystals existed in PP above a formation pressure of 50 MPa. The melting points increased with formation pressure for PET, but remained unchanged for PP and PA66. Density at ambient conditions decreased with formation pressure for PP, but increased for PET and PA66. © 1994 John Wiley & Sons, Inc.     

Influence of copolymeric poly(diethylene glycol) terephthalate on the thermal stability of poly(ethylene terephthalate)

Copolymers of poly(ethylene terephthalate) (PET) containing 1–24% poly(diethylene glycol)terephthalate (PDEGT) were prepared and characterized by infrared spectra. The energy and entropy of activation for the thermal degradation were measured for these copolymers and for the PDEGT. These activation energies and energies and entropies were found to decrease steadily with increasing diethylene glycol content. From these measurements the mechanism of degradation of PDEGT was found to be different from that of PET. Fibers prepared from seven different copolymeric compositions were heat-aged at 121°C and 204°C for 24 hr. From the changes observed in intrinsic viscosity, per cent ether, hydroxyl and carboxyl endgroups during heat aging it became apparent that the mechanisms for decomposition are operative below melt temperatures and can rapidly destroy such copolymers.