Vitrification/devitrification phenomena during isothermal and nonisothermal crystallization of poly(aryl–ether–ether–ketone) (PEEK) and PEEK/poly(ether–imide) blends

We have established time–temperature transformation and continuous-heating transformation diagrams for poly(ether–ether–ketone) (PEEK) and PEEK/poly(ether–imide) (PEI) blends, in order to analyze the effects of relaxation control on crystallization. Similar diagrams are widely used in the field of thermosetting resins. Upon crystallization, the glass transition temperature (T_g) of PEEK and PEEK/PEI blends is found to increase significantly. In the case of PEEK, the shift of the α-relaxation is due to the progressive constraining of amorphous regions by nearby crystals. This phenomenon results in the isothermal vitrification of PEEK during its latest crystallization stages for crystallization temperatures near the initial T_g of PEEK. However, vitrification/devitrification effects are found to be of minor importance for anisothermal crystallization, above 0.1°C/min heating rate. In the case of PEEK/PEI blends, amorphous regions are progressively enriched in PEI upon PEEK crystallization. This promotes a shift of the α-relaxation of these regions to higher temperatures, with a consequent vitrification of the material when crystallized below the T_g of PEI. The data obtained for the blends in anisothermal regimes allow one to detect a region in the (temperature/heating rate) plane where crystallization proceeds in the continuously close proximity of the glass transition (dynamic vitrification). These experimental findings are in agreement with simple simulations based on a modified Avrami model coupled with the Fox equation. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 919–930, 1998     

Analysis of crystallization kinetics of poly(ether ether ketone)

An optical microscope equipped with a video photograph system was used to follow the growth of spherulites. Under nitrogen atmosphere, the growth rates at 290 and 300°C suggest that when the melt of PEEK has been equilibrated for 15 min at 400°C, the subsequent crystallization behavior was nearly independent of the prior thermal history. Linear growth rates of crystallization of PEEK have been measuredin the temperature range of 260–325°C for melt-pressed films and solvent cast films. Detailed kinetic analysis indicated that PEEK exhibited an unmistakable regime II → III transition at 296 ± 1°C. The II → III transition was clearly present irrespective of the rather drastic changes in U*. It is interesting that the branching and crosslinking retarded the growth rate of PEEK, but a transition from regime II to regime III still existed. For melt-pressed films after equilibration at 400°C for 15 min, values of σ and q suggest that U* should be taken nearer to 1500 cal/mol in the case of T_∞ = T_g − 30 K and 2000 cal/mol in the case of T_∞ = T_g − 51.6 K. The K_g(III)/K_g(II) ratio (1.32) was not as close to the predicted value of 2 as was Hoffman's ratio. For PEEK, the Thomas-Staveley constant (β) should be closer to 0.25 or 0.3 instead of 0.1. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1335–1348, 1998     

SAXS/WAXS/DSC studies on crystallization of a polystyrene-b-poly(ethylene oxide)-b-polystyrene triblock copolymer with lamellar morphology and low glass transition temperature

Crystallization of a polystyrene-b-poly(ethylene oxide)-b-polystyrene (S-EO-S) triblock copolymer, S₄₀EO₁₃₆S₄₀, with lamellar morphology in the melt and low glass transition temperature (T_g=47 °C) of the S block was studied. The triblock copolymer was cooled from ordered melt and isothermal crystallization was conducted at crystallization temperatures (T_c) near the T_g of the S block. It is found that crystallization behavior of S₄₀EO₁₃₆S₄₀ strongly depends on T_c. When T_c is far below T_g, an Avrami exponent n=0.5 is observed, which is attributed to diffusion-controlled confined crystallization. As T_c slightly increases, the Avrami exponent is 1.0, indicating that crystallization is confined and crystallization rate is determined by the rate of homogeneous nucleation. When T_c is just below the T_g of the S block, crystallization tends to become breakout and accordingly Avrami exponent changes from 1.0 to 3.2. Crystallinity and melting temperature of the EO block in breakout crystallization are slightly higher than those in confined crystallization. Time-resolved small and wide angle X-ray scattering (SAXS/WAXS) were used to monitor isothermal crystallization of S₄₀EO₁₃₆S₄₀. It shows that the long period is constant in confined crystallization, but it gradually increases during breakout crystallization. WAXS result reveals that confined or breakout crystallization has no effect on the crystal structure of the EO block.     

Studies of the enthalpy relaxation and the “multiple melting” behavior of semicrystalline poly(arylene ether ether ketone) (PEEk)

We report the results of an investigation by differential scanning calorimetry (DSC) of two mobility controlled processes in the amorphous phas e of semicrystalline PEEK — enthalpy relaxation below the glass transition (T _g) and secondary crystallization aboveT _g. Both result in the observation of an endothermic peak just above the annealing temperature in the DSC scan of the polymer — the enthalpy recovery peak and the low temperature melting peak, respectively. There is a striking similarity in the time and temperature dependence of the endothermic peak for these two processes. These results are reminiscent of those obtained from small strain creep studies of physical aging of semicrystalline PEEK below and aboveT _g.We gratefully acknowledge support of this work by the National Science Foundation, Science and Technology Center for High Performance Polymeric Adhesives and Composites under DMR grant 91-2004 and by an NSF Young Investigator Award (DMR 93-57512).     

Physical aging of poly(ether sulfone)-modified epoxy resin

The physical aging process of 4,4′-diaminodiphenylsulfone (DDS) cured diglycidyl ether bisphenol-A (DGEBA) blended with poly(ether sulfone) (PES) was studied by differential scanning calorimetry (DSC) at four aging temperatures between T_g-50°C and T_g-10°C. At aging temperatures between T_g-50 and T_g-30°C, the experimental results of epoxy resin blended with 20 wt% of PES showed two enthalpy relaxation processes. One relaxation process was due to the physical aging of PES, the other relaxation process was due to the physical aging of epoxy resin. The distribution of enthalpy relaxation process due to physical aging of epoxy resin in the blend was broader and the characteristic relaxation time shorter than those of pure epoxy resin at the above aging temperatures (between T_g-50 and T_g-30°C). At an aging temperature between T_g-30 and T_g-10°C, only one enthalpy relaxation process was found for the epoxy resin blended with PES, the relaxation process was similar to that of pure epoxy resin. The enthalpy relaxation process due to the physical aging of PES in the epoxy matrix was similar to that of pure PES at aging temperatures between T_g-50 and T_g-10°C. © 1997 John Wiley & Sons, Inc.     

Kinetics of crystallization of Zr52Cu18Ni14Al10Ti6 metallic glass

Metallic glasses have received considerable attention in comparison to normal metallic materials due to their superior physical and mechanical properties. These systems possess large under cooled region, ∆T (∆T = T _x − T _g where, T _x is crystallization temperature and T _g is glass transition temperature) and hence increased thermal stability against crystallization. Due to this, the study of their crystallization kinetics is important and interesting. It is interesting because of the fact that, crystallization becomes multi-step process due to several components present in these systems. In this paper, we report the experimental investigations of crystallization of Zr₅₂Cu₁₈Ni₁₄Al₁₀Ti₆ glassy alloy system, which is among the best non-beryllium containing glasses, using differential scanning calorimetry (DSC). The crystallization, as expected, consists of multiple steps. Interestingly, the peak heights of these steps vary with heating rate. At lower heating rates, first peak is most prominent and subsequently diminishes with increase in heating rate with last peak prominence visible at highest heating rate. Both, iso-kinetic and iso-conversional methods of analysis of kinetics of crystallization have been used to evaluate the activation energy and Avrami exponents and consistent results are obtained.     

Relationship between morphology and glass transition temperature in solvent-crystallized poly(aryl ether ketones)

The relationship between semicrystalline morphology and glass transition temperature has been investigated for solvent-crystallized poly(ether ether ketone) (PEEK) and poly(ether ketone ketone) (PEKK). Solvent-crystallized specimens of both PEEK and PEKK displayed a sizeable positive offset in T_g compared to quenched amorphous specimens as well as thermally crystallized specimens of comparable bulk crystallinity; the offset in T_g for the crystallized samples reflected the degree of constraint imposed on the amorphous segments by the crystallites. Small-angle X-ray scattering studies revealed markedly smaller crystal long periods (d) for the solvent-crystallized specimens compared to samples prepared by direct cold crystallization. The strong inverse correlation observed between T_g and interlamellar amorphous thickness (l_A) based on a simple two-phase model was in excellent agreement with data reported previously for PEEK, and indicated the existence of a unique relationship between glass transition temperature and morphology in these poly(aryl ether ketones) over a wider range of sample preparation history and lamellar structure than was previously reported. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 65–73, 1998     

Physical transitions and crystallization phenomena in poly(ethylene terephthalate) studied by microhardness

The crystallization behavior of poly(ethylene terephthalate) both with and without sodium montanate, a crystal nucleating agent, has been studied using the microhardness technique. The kinetics of crystallization from the glassy state were investigated in real time by measuring the microhardness H at different crystallization temperatures. Results are discussed in terms of the Avrami equation. Values of the Avrami exponent n of about 3 are observed for samples irrespective of nucleating agent. For samples with nucleant two crystallization ranges are observed: a first range which corresponds to a fast crystallization from nucleating agent particles and a second range which is associated with a slow self-crystallization mode. New transitions evidenced by the presence of a small maximum in H as a function of annealing time and temperature are detected at temperatures above T_g for physically aged samples. The kinetics of this transition have also been examined. It is further shown that the presence of nucleating agent induces a hardening at room temperature which is similar to the effect produced by the physical aging of the samples below T_g. Finally, it is found that aging reduces the rate of creep of the material under the indenter. © 1993 John Wiley & Sons, Inc.     

Impact of plasticizers and tackifiers on the crystallization of isotactic poly(1-butene)

Crystallization of a semi-crystalline polyolefin in the presence of low molecular weight modifiers was quantified by differential scanning calorimetry and optical microscopy. The polyolefin was a commercial grade of isotactic poly(1-butene) (iPB). Two modifiers were used: an oligomeric plasticizer, designated HOAO, which decreased the glass transition temperature (T_g) of the system, and an oligomeric tackifier, designated HOCP, which increased T_g. Binary iPB/modifier blends containing 10% or 20% by weight of HOAO or HOCP were examined to determine how their addition affects T_g, while ternary iPB/HOAO/HOCP blends containing 10% or 20% by weight of total modifier were examined to determine the effects of dilution by using a ratio of HOAO to HOCP that matched the T_g of iPB. The addition of modifier decreased the nucleation rate, spherulitic crystal growth rate, and final crystallinity of each blend. However, only the nucleation rate showed a dependence on the type of modifier, with nucleation retarded more by HOCP than by HOAO. A Hoffman-Weeks analysis of the melting point as a function of crystallization temperature confirmed that the driving force for nucleation was reduced, and that the effect was larger for HOCP. An Avrami analysis of the bulk crystallization kinetics was consistent with these observations, as the Avrami exponents were in the range of 3-4.     

Plasticization and crystallization of cis-1,4 polyisoprene mixed with methyl linolate

Crystallization behavior of synthetic cis-1,4 polyisoprene mixed with methyl linolate was investigated by differential scanning calorimetry and dilatometry. At isothermal crystallization temperature of ?25°C, a rate of crystallization decreased with the addition of 1 wt % methyl linolate, whereas it increased with a large amount of methyl linolate, about 30% by weight. Although Avrami constant of cis-1,4 polyisoprene was 2.82, that of mixtures containing 1 and 30 wt % methyl linolate was found to be approximately 4. This implies the same crystallization mechanism was in operation in the mixtures. Since glass transition temperature, T_g, of cis-1,4 polyisoprene decreased as the methyl linolate content of mixture increased, methyl linolate was found to be plasticizer for cis-1,4 polyisoprene. The increase in the rate of crystallization in the mixtures was corresponding to the decrease in T_g. © 1995 John Wiley & Sons, Inc.     

Quantitative nanoscale measurements of the thermomechanical properties of poly-ether-ether-ketone (PEEK)

Understanding the internal structure and organization of semicrystalline polymers, especially at the nanoscale, has many challenges for researchers to date. In this article, we demonstrate a quantitative method for investigating the local viscoelastic properties (i.e., storage and loss moduli, as well as loss tangent) of semicrystalline polyether-ether ketone (PEEK) through the combination of contact resonance atomic force microscopy (CR-AFM) and in situ local heating with a thermal probe. Furthermore, the local viscoelastic properties of the crystalline and amorphous phases were decoupled by performing thermal CR-AFM array mapping near the glass transition temperature of PEEK (T_g, 143 °C). A distinct bimodal distribution of tip-sample interaction was observed for PEEK near its T_g, providing a means to estimate the T_g and the degree of crystallinity of PEEK.     

Segmental and secondary dynamics in hydrogen‐bonded poly(4‐vinylphenol)/poly(methyl methacrylate) blends

Broadband dielectric spectroscopy was used to study the segmental (α) and secondary (β) relaxations in hydrogen‐bonded poly(4‐vinylphenol)/poly(methyl methacrylate) (PVPh/PMMA) blends with PVPh concentrations of 20–80% and at temperatures from ?30 to approximately glass‐transition temperature (T_g) + 80 °C. Miscible blends were obtained by solution casting from methyl ethyl ketone solution, as confirmed by single differential scanning calorimetry T_g and single segmental relaxation process for each blend. The β relaxation of PMMA maintains similar characteristics in blends with PVPh, compared with neat PMMA. Its relaxation time and activation energy are nearly the same in all blends. Furthermore, the dielectric relaxation strength of PMMA β process in the blends is proportional to the concentration of PMMA, suggesting that blending and intermolecular hydrogen bonding do not modify the local intramolecular motion. The α process, however, represents the segmental motions of both components and becomes slower with increasing PVPh concentration because of the higher T_g. This leads to well‐defined α and β relaxations in the blends above the corresponding T_g, which cannot be reliably resolved in neat PMMA without ambiguous curve deconvolution. The PMMA β process still follows an Arrhenius temperature dependence above T_g, but with an activation energy larger than that observed below T_g because of increased relaxation amplitude. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3405–3415, 2004     

Molecular relaxation of isotactic polystyrene: Real‐time dielectric spectroscopy and X‐ray scattering studies*

The molecular relaxation processes and structure of isotactic polystyrene (iPS) films were investigated with real‐time dielectric spectroscopy and simultaneous wide‐ and small‐angle X‐ray scattering. The purpose of this work was to explore the restrictions imposed on molecular mobility in the vicinity of the α relaxation (glass transition) for crystallized iPS. Isothermal cold crystallization at temperatures of T_c = 140 or 170 °C resulted in a sigmoidal increase of crystallinity with crystallization time. The glass‐transition temperature (T_g), determined calorimetrically, exhibited almost no increase during the first stage of crystal growth before impingement of spherulites. After impingement, the calorimetric T_g increased, suggesting that confinement effects occur in the latter stages of crystallization. For well‐crystallized samples, the radius of the cooperativity region decreased substantially as compared with the purely amorphous sample but was always smaller than the layer thickness of the mobile amorphous fraction. Dielectric experiments directly probed changes in the amorphous dipole mobility. The real‐time dielectric data were fitted to a Havriliak–Negami model, and the time dependence of the parameters describing the distribution of relaxation times and dielectric strength was obtained. The central dipolar relaxation time showed little variation before spherulite impingement but increased sharply during the second stage of crystal growth as confinement occurred. Vogel–Fulcher–Tammann analysis demonstrated that the dielectric reference temperature, corresponding to the onset of calorimetric T_g, did not vary for well‐crystallized samples. This observation agreed with a model in which constraints affect primarily the modes having longer relaxation times and thus broaden the glass‐transition relaxation process on the higher temperature side. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 777–789, 2004     

Shear influence on the phase behavior of systems containing a homopolymer A and a block copolymer AB

Cloud point temperatures (T_cp) and crystallization temperatures (T_l/s) of the ternary system tetrahydronaphthalene/poly(ethylene oxide)/poly(dimethyl siloxane-b-ethylene oxide) have been measured at different constant shear rates using a rheo-optical device and an advanced rheometer. The cloud points temperatures (UCST-type phase diagram) are reduced by several degrees as the system flows; i.e. the shear can suppress the phase separation and enlarge the homogenous region. The crystallization kinetics of PEO in the ternary mixtures has been investigated isothermally and non-isothermally at quiescent state and under shear. The shear could strongly enhance the crystallization i.e. the (T_l/s) shifts to higher temperatures and the induction time, t₀ (the time needs for the onset of crystallization) substantially decreases with increasing shear rate during the non-isothermal and isothermal crystallization processes, respectively. The isothermal crystallization kinetics at quiescent state and at different shear rates was analyzed on the bases of Avrami approach. The Avrami exponent which provides qualitative information about the nature of the nucleation and growth process, was found to be shear rate and temperature dependent. The Avrami exponent increased from ∼3 at the quiescent state to as large as 9 at &&ggr;dot; = 100 s⁻¹.     

Crystallization kinetics of poly(trimethylene terephthalate)

The isothermal crystallization kinetics of poly(trimethylene terephthalate) (PTT) have been investigated using differential scanning calorimetry (DSC) and polarized light microscopy (PLM). Enthalpy data of exotherm from isothermal crystallization were analyzed using the Avrami theory. The average value of the Avrami exponent, n, is about 2.8. From the melt, PTT crystallizes according to a spherulite morphology. The spherulite growth rate and the overall crystallization rate depend on crystallization temperature. The increase in the spherulitic radius was examined by polarized light microscopy. Using values of transport parameters common to many polymers (U* = 1500 cal/mol, T_∞= T_g − 30 °C) together with experimentally determined values of T (248 °C) and T_g (44 °C), the nucleation parameter, k_g, for PTT was determined. On the basis of secondary nucleation analyses, a transition between regimes III and II was found in the vicinity of 194 °C (ΔT ≅ 54 K). The ratio of k_g of these two regimes is 2.1, which is very close to 2.0 as predicted by the Lauritzen–Hoffman theory. The lateral surface‐free energy, σ = 10.89 erg/cm² and the fold surface‐free energy, σ_e = 56.64 erg/cm² were determined. The latter leads to a work of chain‐folding, q = 4.80 kcal/mol folds, which is comparable to PET and PBT previously reported. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 934–941, 2000     

The preparation,compatibility and structure of PEEK–PES blends

Blends of polyetheretherketone and polyethersulfone (PEEK–PES blends) were prepared either by mechanically mixing fine PEEK and PES powders or by mixing PEEK and PES solutions in H₂SO₄ (98%). Partially compatible blends were obtained in the latter method. The sulfurization of PEEK or PES in concentrated sulphuric acid did not occur provided that the experiment was performed within 30 min. The T_g of the PEEK component increased and that of PES component decreased with the increase of PES weight fraction; the melting exothermic peak of the PEEK component did not appear in the DSC curves of the quenched blends, suggesting that PES can effectively reduce the crystallization of PEEK component. The major absorbances of the bands were characterized by IR spectroscopy; the frequency difference between PEEK or PES and their blends were observed. A linear correlation of absorbance ratios with PEEK weight fraction was found.     

Effects of diluent on molecular motion and glass transitions in polymers. III. The system poly(vinyl acetate)–toluene

Dielectric measurements, differential thermal analyses (DTA), and broad-line proton magnetic resonance (NMR) measurements are reported on the system poly(vinyl acetate)–toluene. Four dielectric relaxations were observed between 80 and 400°K. From proton NMR measurements on solutions in toluene and in deuterated toluene, the relaxation processes can be assigned, respectively, to segmental motion of poly(vinyl acetate), α; motion of side group, β′ rotation of toluene, β; local motions of poly(vinyl acetate) and toluene, γ, in order of appearance with decreasing temperature. Two stepwise changes in DTA traces have been observed and can be assigned as glass transition points T_gI and T_gII. Comparison of these glass transition points with temperatures at which dielectric relaxation times for the α and β processes are 100 sec, indicate that segmental motion of poly(vinyl acetate) and rotation of toluene are frozen-in at T_gI and T_gII, respectively. Activation plots for the α process conform to the Vogel–Tamman equation. In terms of the parameters A, B, and T₀ of the equation, T_gI can be represented by an expression of the form T_gI ≈ T₀ + B/(A + 3). In the range of concentration above 50% by weight, A and B are almost independent of concentration but T₀ varies strongly. The nature of the secondary dispersions is also discussed.     

Glass transition and miscibility in blends of two semicrystalline polymers: Poly(aryl ether ketone) and poly(ether ether ketone)

Binary melt‐blended mixtures of two aryl ether ketone polymers (i.e., a new poly(aryl ether ketone) (code name PK99) and poly(ether ether ketone) (PEEK), have been studied. Polymer miscibility in glassy amorphous (or melt) domains has been demonstrated for the binary blend comprising of two aryl‐ether‐ketone‐type semicrystalline polymers. Composition‐dependent, single T_g was observed within full composition range in the PK99/PEEK blends, and the narrow T_g breadth also suggests that the scale of mixing was fine and uniform. To better resolve any possible overlapping T_g's, physical aging was imposed on a comparison set of blend samples for the purpose of improving detectability of overlapped multiple transitions if existing. The result still showed one single T_g. The relative sharp T_g and lack of cloud point transition suggest that the scale of molecular intermixing is good. Phase homogeneity was further confirmed using optical and scanning electron microscopy. The X‐ray diffractograms suggest that isomorphism does not exist in the PK99/PEEK blends and that the crystal forms of the respective polymers remain distinct and unchanged by the miscibility in the amorphous region. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1485–1494, 1999     

Revisiting the crystallization of poly(2‐alkyl‐2‐oxazoline)s

Poly(2‐alkyl‐2‐oxazoline)s (PAOx) exhibit different crystallization behavior depending on the length of the alkyl side chain. PAOx having methyl, ethyl, or propyl side chains do not show any bulk crystallization. Crystallization in the heating cycle, that is, cold crystallization, is observed for PAOx with butyl and pentyl side chains. For PAOx with longer alkyl side chains crystallization occurs in the cooling cycle. The different crystallization behavior is attributed to the different polymer chain mobility in line with the glass transition temperature (T_g) dependency on alkyl side chain length. The decrease in chain mobility with decreasing alkyl side chain length hinders the relaxation of the polymer backbone to the thermodynamic equilibrium crystalline structure. Double melting behavior is observed for PButOx and PiPropOx which is explained by the melt‐recrystallization mechanism. Isothermal crystallization experiments of PButOx between 60 and 90 °C and PiPropOx between 90 and 150 °C show that PAOx can crystallize in bulk when enough time is given. The decrease of T_g and the corresponding increase in chain mobility at T > T_g with increasing alkyl side chain length can be attributed to an increasing distance between the polymer backbones and thus decreasing average strength of amide dipole interactions. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 721–729     

Glass transition of semi-crystalline PLLA with different morphologies as studied by dynamic mechanical analysis

Poly(l-lactic acid) was crystallized from the glassy state at different temperatures to produce fully transformed semi-crystalline specimens exhibiting different lamellar morphologies. The materials were tested by dynamic mechanical analysis, where a T _g decrease was found with an increasing crystallization temperature. Considering a three-phase model, this tendency was related to the corresponding increase in the thickness of the rigid amorphous phase. It is suggested that this phase could, in some extent, accommodate through local translational/rotational motions the cooperative motions taking place within the mobile amorphous phase. This could be due to the non-compact structure of the cooperatively rearranging regions, which can present a string-like or fractal structure in their edges. The width of the loss factor peak associated to the glass transition increases with increasing crystallization temperature, suggesting an increase in the broadness of the distribution of relaxation times. The drop in the storage modulus across T _g varies systematically with the crystallization temperature in the different materials and could be correlated with the crystalline content. Above T _g, the loss factor exhibits a plateau-like behaviour at significantly high values, which seems to be a rather general behaviour in semi-crystalline systems that could be related to the contribution of pure irreversible flow in the overall viscoelastic behaviour.