Polymers from 4,4′-thiodiphenol

Polyesters were made with aromatic diacid chlorides and 4,4,-thiodiphenol. Isophthaloyl chloride and/or terephthaloyl chloride were used as acid chlorides alone or together with 5-cyanoisophthaloyl chloride or [2.2]p-cyclophane-3,9-dicarboxylic acid chloride. The latter components were incorporated in order to make the polymers useful for crosslinking. A polyether could be obtained by polycondensation of 2,4-dichloro-benzonitrile and 4,4′-thiodiphenol. The polycondensations were run in nitrobenzene as solvent.     

Polyamides from perchloro-4,4′-dichloroformylbiphenyl

New thermally stable polyamides were prepared by low-temperature polycondensation in N,N-dimethylacetamide from perchloro-4,4′-dichloroformylbiphenyl and various aromatic and aliphatic diamines. The polymers were characterized by infrared spectroscopy, elemental analysis, TGA, and DSC and found to show higher thermal stability than other nonchlorinated polyamides.     

Synthesis and characterization of photosensitive polyimides from methylthiomethyl-substituted 4,4′-diaminodiphenylmethanes and 3,3′,4,4′-benzophenonetetracarboxylic dianhydride

A series of novel polyimides are synthesized by the reaction of 3,3′,4,4′-benzophenonete-tracarboxylic dianhydride (BTDA) with four methylthiomethyl-substituted aromatic diamines: 3-methylthiomethyl-4,4′-diaminodiphenylmethane ( I ), 3,3′-dimethylthiomethyl-4,4′-diaminodiphenylmethane ( II ), 3,3′,5-trimethylthiomethyl-4,4′-diaminodiphenylmethane ( III ), and 3,3′,5,5′-tetramethylthiomethyl-4,4′-diaminodiphenylmethane ( IV ) in refluxing m-cresol. The polyimide of diamine I and BTDA carrying only one pendant methylthiomethyl group in a repeating unit is readily soluble in m-cresol, chloroform, and polar aprotic solvents. Increasing the number of the pendant group results in higher solubility. These fully imidized polyimides are also intrinsically photosensitive. The fraction of photoreactive benzophenone sites that relates to the rate and degree of completion of photocrosslinking reaction increases systematically with the increase of the pendant group content. As the average number of the pendant group in a repeating unit reaches 3, 63% of benzophenone sites are found to be photoreactive. These methylthiomethyl-substituted polyimides possess moderate tensile strength which falls in the range of 67–81 MPa. As a result of the increase of methylthiomethyl content, this type of polyimide reveals higher glass transition temperature but lower thermal stability due to the considerable dimension of the pendant group and the ready cleavage nature of the C? S bond. © 1993 John Wiley & Sons, Inc.     

Mass spectral fragmentation pattern of 4,4′-bipyridines. Part II. 4,4′-oxybispyridine and 4,4′-thiobispyridine

The mass spectra of 4,4′-oxybispyridine and 4,4′-thiobispyridine are reported. In the former the base peak is due to the molecular ion and the fragmentation routes involve loss of H, CO, HCN, C₂H₂N and C_sHO from the molecular ion as well as rupture of the central bonds. In the latter the base peak is also due to the molecular ion and the fragmentation routes involve loss of H, CS, S, HCN and C₂HS as well as central bond rupture.     

Mass spectra of some tetrasubstituted 4,4′-biisoxazoles and 4,4′-methylendiisoxazoles

The behaviour of some tetrasubstituted 4,4′-biisoxazoles and 4,4′-methylendiisoxazoles under electron impact has been investigated by means of high and low resolution mass spectrometry. The determination of metastable transitions and accurate masses of important fragment ions has led to the construction of fragmentation schemes. Specific skeletal rearrangement processes are discussed and it is proposed that they proceed through azirine and oxazole intermediates.     

Sorption and transport of carbon dioxide in a polyimide from 3,3′4,4′-biphenyltetracarboxylic dianhydride and 4,4′-diaminodiphenyl sulfone

CO₂ sorption and transport were investigated for the polyimide prepared from 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) and 4,4′-diaminodiphenyl sulfone (DDS). The morphology of films did not change on annealing above the glass transition temperature and remained amorphous unlike the polyimide prepared from BPDA and 4,4′-oxydianilline (ODA). This seems to be due to the strong hindrance to rotation of the sulfonyl linkage. Sorption and transport data were analyzed according to the dual-mode model. Solubility, diffusion, and permeability coefficients at 20 atm and 80°C for BPDA-DDS polyimide were substantially equal between as-cast and annealed films and were 1.7, 2.2, and 3.7 times greater, respectively, than for the as-cast films of the BPDA-ODA polyimide. The higher solubility was due to larger values of the Henry's law solubility constant k_D, Langmuir capacity constant C, and the Langmuir affinity constant b. The sorption and transport properties were compared with those for amorphous glassy aromatic polymers including other polyimides. The relation of k, C, b, and the diffusion coefficients in the Henry's law population and the Langmuir population (D_D and D_H) with other properties of the polymers were discussed. Values D_D and D_H for BPDA-DDS polyimide were much larger than expected from the estimated free-volume fraction.     

Shear‐enhanced crystallization of a thermoplastic polyimide derived from 3,3′,4,4′‐oxydiphthalic dianhydride and 4,4′‐oxydianiline

The aim of this work is to investigate the effect of consecutive shear on the crystallization of an amorphous aromatic polyimide (PI) derived from 3,3 ′ ,4,4 ′ ‐oxydiphthalic dianhydride (3,3 ′ ,4,4 ′ ‐ODPA) and 4,4 ′ ‐oxydianiline (ODA). At 260 °C, the increase of shear rate or shear time leads to the increase of crystallinity. Indeed, increasing shear rate can also accelerate the crystallization behavior. Moreover, it was found that a new melting peak appeared at higher temperature for long time or high rate sheared sample. The enhancement of crystallization behavior appears directly linked to the increase of crystal thickness. Particularly, the effect of shear temperature was investigated, and the results revealed that the crystallization of the PI was more sensitive to shear at 260 °C, which was 10° above the glass transition temperature (250 °C) of the PI. Possible mechanism was proposed to illustrate the effect of consecutive shear on the crystallization of the PI polymer. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2344–2349, 2007     

Polyimidines. XI. Polyimidines from 3,3′,4,4′-benzophenonetetracarboxylic dianhydride and 4,4′-(hexafluoroisopropylidene) diphthalic anhydride

Two new bis(benzylidenephthalide)monomers were synthesized by melt condensation of phenylacetic acid with 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) and with 4,4′-(hexafluoroisopropylidene)diphthalic anhydride (6FDA). A mixture of three isomers for each monomer was obtained and polymerized with diamines to produce new polyimidines. Polymerizations were conducted with m-xylylenediamine (MXDA) or 4,4′-oxydianiline (ODA) in quantitative yields for the undehydrated intermediate. Inherent viscosities ranged from 0.17 to 0.35 dL/g in N,N-dimethylformamide (DMF) or N-methyl-2-pyrrolidone (NMP). These intermediate poly(hydroxylactams) were thermally dehydrated to polyimidines which exhibited a 10% weight loss, as high as 546°C in nitrogen. Inherent viscosities of the dehydrated (cured) polyimidines ranged from 0.14 to 0.20 dL/g in NMP. Brittle films could be cast from NMP solutions.     

Aromatic polyether, -ketone, -sulfones as laminating resins. XI. Polymers derived from 2,2′-diiododiphenyl-4,4′-dicarboxylic acid

Aromatic polyether-keto-sulfone polymers and related model compounds have been synthesized from 2,2′-diiododiphenyl-4,4′-dicarboxylic acid and a variety of intermediates. It was hoped to convert them to 2,2′-diphenylethynyl derivatives which could be cured by rearrangement to give dibenzanthracene units in the chain. Low solubilities and high melting points of the products prevented their use in the desired manner.     

Thermotropic liquid‐crystalline polyesters of 4,4′‐biphenol and phenyl‐substituted 4,4′‐biphenols with 4,4′‐oxybisbenzoic acid

A series of thermotropic polyesters, derived from 4,4′‐biphenol (BP), 3‐phenyl‐4,4′‐biphenol (MPBP), and 3,3′‐bis(phenyl)‐4,4′‐biphenol (DPBP), 4,4′‐oxybisbenzoic acid (4,4′‐OBBA), and other aromatic dicarboxylic acids as comonomers, were prepared by melt polycondensation and were characterized for their thermotropic liquid‐crystalline (LC) properties with a variety of experimental techniques. The homopolymer of BP with 4,4′‐OBBA and its copolymers with either 50 mol % terephthalic acid or 2,6‐naphthalenedicarboxylic acid had relatively high values of the crystal‐to‐nematic transition (448–460 °C), above which each of them formed a nematic LC phase. In contrast, the homopolymers of MPBP and DPBP had low fusion temperatures and low isotropization temperatures and formed nematic melts above the fusion temperatures. Each of these two polymers also exhibited two glass‐transition temperatures, which were associated with vitrified noncrystalline (amorphous) regions and vitrified LC domains, as obtained directly from melt polycondensation. As expected, they had higher glass‐transition temperatures (176–211 °C) than other LC polyesters and had excellent thermal stability (516–567 °C). The fluorescence properties of the homopolymer of DPBP with 4,4′‐OBBA, which was soluble in common organic solvents such as chloroform and tetrahydrofuran, were also included in this study. For example, it had an absorption spectrum (λ_max = 259 and 292 nm), an excitation spectrum (λ_ex = 258 and 292 nm with monitoring at 350 nm), and an emission spectrum (λ_em = 378 nm with excitation at 330 nm) in chloroform. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 141–155, 2002     

Synthesis and properties of polyimides from 4,4′-binaphthyl-1,1′,8,8′-tetracarboxylic dianhydride

4,4′-Binaphthyl-1,1′,8,8′-tetracarboxylic dianhydride was synthesized from 4-chloro-1,8-naphthalic anhydride and polymerized with aromatic and pliphatic diamines in m-cresol or N-methyl-2-pyrrolidinone (NMP). The polyimides, except for two derived from p-phenylenediamine and hydrazine, are soluble in 1,1,2,2-tetrachloroethane and NMP. Their intrinsic viscosities ranged from 0.36 to 2.20 dL/g. The polymers showed excellent thermal and thermooxidative stabilities and displayed weak glass transition temperatures. Young's moduli of some polymer films were in the range of 2.5 and 5.4 GPa at 30°C. The aliphatic polyimides exhibited a stronger fluorescence than the aromatic polyimides. © 1995 John Wiley & Sons, Inc.     

A zinc(II) metal–organic framework with a novel topology formed from 4,4′,4′′‐nitrilotribenzoate and 4,4′‐bipyridine ligands

A metal–organic framework with a novel topology, poly[sesqui(μ₂‐4,4′‐bipyridine)bis(dimethylformamide)bis(μ₄‐4,4′,4′′‐nitrilotribenzoato)trizinc(II)], [Zn₃(C₂₁H₁₂NO₆)₂(C₁₀H₈N₂)_1.5(C₃H₇NO)₂]_n, was obtained by the solvothermal method using 4,4′,4′′‐nitrilotribenzoic acid and 4,4′‐bipyridine (bipy). The structure, determined by single‐crystal X‐ray diffraction analysis, possesses three kinds of crystallographically independent Zn^II cations, as well as binuclear Zn₂(COO)₄(bipy)₂ paddle‐wheel clusters, and can be reduced to a novel topology of a (3,3,6)‐connected 3‐nodal net, with the Schläfli symbol {5.6²}₄{5².6}₄{5⁸.8⁷} according to the topological analysis.     

Synthesis of difurazanyl ethers from 4,4′‐dinitroazoxyfurazan

Nonselective attacks at the carbon bonded to a nitro group and carbon bonded to the N(O) atom of the azoxy group were observed in the reactions of 4,4′‐dinitroazoxyfurazan with bases and nucleophiles. A mechanism is presented to account for both of the pathways to products. A series of new difurazanyl ether derivatives was synthesized. © 2000 John Wiley & Sons, Inc. Heteroatom Chem 11:48–56, 2000     

2,2′,4,4′,6,6′‐Hexa­methyl‐4,4′‐bi­[4H‐pyran­yl]

The title mol­ecule, C₁₆H₂₂O₂, reveals C_i point symmetry in the crystal structure. The structure was disordered. The pyran ring is not planar; the O atom lies significantly out of the least‐squares plane (ten times the r.m.s. deviation of all six atoms).     

Effect of Metal Ions on the Structures of Coordination Polymers Based on Biphenyl‐2,2′,4,4′‐Tetracarboxylate

Two new coordination polymers, {[Cd₂(btc)(2,2′‐bpy)₂] · H₂O}_n ( 1 ) and [Zn₂(btc)(2,2′‐bpy)(H₂O)]_n ( 2 ) (H₄btc = biphenyl‐2,2′,4,4′‐tetracarboxylic acid, 2,2′‐bpy = 2,2′‐bipyridine), were synthesized hydrothermally under similar conditions and characterized by elemental analysis, IR spectra, TGA, and single‐crystal X‐ray diffraction analysis. In complexes 1 and 2 , the (btc)^4– ligand acts as connectors to link metal ions to give a 2D bilayer network of 1 and a 3D metal‐organic framework of 2 , respectively. The differences in the structures are induced by diverging coordination modes of the (btc)^4– ligand, which can be attributed to the difference metal ions in sizes. The results indicate that metal ions have significant effects on the formation and structures of the final complexes. Additionally, the fluorescent properties of the two complexes were also studied in the solid state at room temperature.     

Synthesis and characterization of poly(arylene ether)s derived from 4,4′‐bishydroxybiphenyl and 4,4′‐bishydroxyterphenyl

A series of poly(arylene ether)s were successfully prepared by aromatic, nucleophilic substitution reactions with various perfluoroalkyl‐activated bisfluoromonomers with 4,4′‐bishydroxybiphenyl and 4,4′‐bishydroxyterphenyl. 4,4′‐Bishydroxyterphenyl was synthesized through the Grignard coupling reaction of magnesium salt of 4‐bromoanisole with dibromobenzene followed by demethylation with pyridine–hydrochloride. The products obtained by the displacement of fluorine atoms exhibited good inherent viscosity, up to 0.77 dL/g, and number‐average molecular weights up to 69,300. These poly(arylene ether)s showed very good thermal stability, up to 548 °C for 5% weight loss according to thermogravimetric analysis under synthetic air, and high glass‐transition temperatures, up to 259 °C according to differential scanning calorimetry, depending on the exact repeat unit structure. These polymers were soluble in a wide range of organic solvents, such as N‐methylpyrrolidone, dimethylformamide, tetrahydrofuran, toluene, and CHCl₃, and were insoluble in dimethyl sulfoxide and acetone. Thin films of these poly(arylene ether)s showed good transparency and exhibited tensile strengths up to 132 MPa, moduli up to 3.34 GPa, and elongations at break up to 84%, depending on their exact repeating unit structures. These values are comparable to those of high‐performance thermoplastic materials such as poly(ether ether ketone) (PEEK) and Ultem poly(ether imide) (PEI). These poly(arylene ether)s exhibited low dielectric constants. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 55–69, 2002     

Mass spectral fragmentation pattern of 4,4′-bipyridyls. Part I. 4,4′-bipyridyl

The mass spectral fragmentation pattern of 4,4′-bipyridyl is described. The fragmentation proposals which differ from those previously reported are supported by high resolution mass measurements and metastable transitions.     

On the configuration of 4,4′,6,6′-tetraphenyl-2,2′-dithiopyrylene

The title compound showed in its UV-VIS absorption spectra large red shifts of bands from solution to crystal indicating a pronounced intermolecular interaction between the dithiopyrylene π-electron systems. Dipole moment measurement in benzene solution gave a dipole moment value of 1.90 D which offers a direct evidence for the molecule in cis-configuration.