Effect of urea on poly(methacrylic acid) and poly(acrylic acid) aqueous solutions

The effects of urea on aqueous solutions of both poly(methacrylic acid (PMA) and poly(acrylic acid) (PAA) have been investigated by using potentiometry, viscometry and study of the fluorescence of Auramine O, a cationic dye. The viscosity behaviour of unionized PMA obtained from direct dissolution of solid powder shows that the unneutralized macromolecules can be associated in water. The stability of such “aggregates” seems weak as indicated by their disappearance as soon as the charge density is very low. For PMA salt solution percolated through a cation (H⁺) exchange resin column, no association is observed. The pH-dependent conformational behaviour of PMA which, contrary to PAA, presents compact conformations in water at low charge density is discussed in terms of solvophobic/solvophilic interactions. It is shown that, even for urea concentration up to 8 M, the compact conformations of PMA are not completely destroyed. The formation of H⁺/urea complex is taken into account.     

The synthesis and characterization of monodisperse poly(acrylic acid) and poly(methacrylic acid)

A number of polyacrylic (PAA) and polymethacrylic (PMAA) acids have been synthesized by living anionic polymerization of the monomeric tert-butyl esters followed by subsequent hydrolysis of the corresponding polyesters. The necessary precautions were taken in order to assure good molecular weight control, as well as high yields in the polymerization reactions. The intermediate and final polymers were characterized by gel permeation chromatography and NMR-H¹ spectrometry.     

Calorimetric investigation of poly(methacrylic acid) and poly(acrylic acid) in aqueous solution

The enthalpy of dissociation of poly(acrylic acid) and of poly(methacrylic acid) in water and in 0.5N NaCl at 25°C has been measured over a wide range of degrees of neutralization of the polyelectrolytes. In the case of poly(methacrylic acid) the calorimetric data permit the direct evaluation of the enthalpy of conformational transition of the polymer. For this transition, with the aid of standard free energy data derived from potentiometric titrations, the change in entropy was also estimated. The relative accuracy of the thermodynamic data, and the possibility of deriving therefrom information on the mechanism of transitions of the type, globular coils → expanded coils for partially hydrophobic synthetic polyelectrolytes in aqueous solution are discussed.     

Binding of a surfactant counterion to low-charge-density poly(acrylic acid) and poly(methacrylic acid)

The binding of a cationic surfactant, dodecylpyridinium (C12Py) chloride, with a low-charge-density poly (methacrylic acid) (PMA) was investigated in buffer solutions under the condition of constant pH. The binding isotherms with PMA consisted of two and three steps at a pH lower and higher than 3.2, respectively. Bindings in the first step were independent of pH and this step was considered to correspond to the solubilization of the hydrocarbon chains of C12Py into the nonpolar region of the compact form of PMA. This is the indication of the compact form from the binding isotherm. At pH higher than 3.2, the second step was discriminated and it depended on the pH. In the third step, a sharp rise in the degree of binding (β) was observed accompanying the solubilization of the precipitates of the PMA–C12Py complex. The binding with poly(acrylic acid) (PAA) and PMA in conventional unbuffered NaCl solutions was also examined and the pH profile of the solution during the binding process was determined. In the case of unbuffered NaCl solutions, the binding with PAA took place cooperatively at the critical association concentration (cac). The binding isotherm consisted of two steps and the pH decreased with the increase in β. The binding isotherm of PMA, on the other hand, consisted of three steps: the pH decreased slightly in the first step and considerably in the second step with the increase in β but it increased with β in the third step, exhibiting a pH minimum around 3.2. The binding in the first step coincided with that obtained in the buffered solutions. Linear relationships between β and the pH were found for both polymers. In the case of PMA, no cac was observed in both buffered and unbuffered NaCl solutions. Received: 24 January 2001 Accepted: 23 May 2001     

Analytical strategy for the molecular weight determination of random copolymers of poly(methyl methacrylate) and poly(methacrylic acid)

Molecular weight characterization of random amphiphilic copolymers currently represents an analytical challenge. In particular, molecules composed of methacrylic acid (MAA) and methyl methacrylate (MMA) as the repeat units raise issues in commonly used techniques. The present study shows that when random copolymers cannot be properly ionized by MALDI, and hence detected and measured in MS, one possible analytical strategy is to transform them into homopolymers, which are more amenable to this ionization technique. Then, by combining the molecular weight of the so-obtained homopolymers, as measured by MS, with the relative molar proportion of the MMA and MMA units, as given by ¹H NMR spectrum, one can straightforwardly estimate the molecular weight of the initial copolymer. A methylation reaction was performed to transform MAA-MMA copolymer samples into PMMA homopolymers, using trimethylsilyldiazomethane as a derivatization agent. Weight average molecular weight (M _w) parameters of the MAA-MMA copolymers could then be derived from M _w values obtained for the methylated MAA-MMA molecules by MALDI, which were also validated by pulsed gradient spin echo (PGSE) NMR. An alkene function in one of the studied copolymer end-groups was also shown to react with the methylation agent, giving rise to MMA-like polymeric by-products characterized by tandem mass spectrometry and which could be avoided by adjusting the amount of the trimethylsilyldiazomethane in the reaction medium.     

Activity of counterions in hydrogels based on poly(acrylic acid) and poly(methacrylic acid): Potentiometric measurements

The behavior of partially ionized weakly crosslinked gels based on poly(acrylic acid) and poly(methacrylic acid) undergoing contraction in the presence of a low-molecular-mass salt is studied experimentally. The concentration dependences of the enthalpies of swelling of gels in water and aqueous solutions with potassium chloride concentrations of 1, 10, and 100 mmol/L are determined via the method of isothermal calorimetry. On the basis of the obtained data, the enthalpy parameter of interaction between a polymer network and a medium is estimated as a function of the amount of the salt. This parameter does not exceed 0.3 and monotonically decreases with an increase in the concentration of the salt. The Donnan potential of gels depending on the concentration of KCl in the external solution is measured via the method of potentiometry with the use of capillary electrodes, and the activity of potassium counterions in the medium of hydrogel is calculated. The main factor that causes contraction of polyelectrolyte gels in a solution of a low-molecular-mass salt is a decline in the activity of counterions that leads to a decrease in the osmotic pressure inside the gel. A decline in activity may be associated with both a reduction in the activity coefficient and ionic association processes in the hydrogel.     

Molecular structure and dynamics of poly(methacrylic acid) and poly(acrylic acid) complexes with dodecyl-substituted poly(ethylene glycol)

The molecular dynamics and the structure of molecular complexes formed by micelles of dodecyl-substituted poly(ethylene glycol) with poly(methacrylic acid) and poly(acrylic acid) in aqueous solutions were studied by viscosimetry, pH measurement, and electron spin resonance spin-probe techniques. At low surfactant concentrations, the conformation of the complex is a compact globule. The local mobility of surfactant molecules in such a complex is much slower than that in the free micelle. At high surfactant concentration, the nonionic micelles and polyacids form hydrophilic associates. The associates have the conformation of extended coils. In an associate, a major part of the micellar poly(ethylene glycol) groups is free. The local mobility of the micellar phase depends on the number of micelles involved in an associate. The mobility of surfactant molecules is slower in the complexes of poly(methacrylic acid) than in the complexes of poly(acrylic acid).     

Thermoresponsive copolymers of methacrylic acid and poly(ethylene glycol) methyl ether methacrylate

Copolymers of methacrylic acid (MAA) and poly(ethylene glycol) methyl ether methacrylate (PEGMA) were prepared and their cloud points in aqueous solution were studied as a function of comonomer ratio, solution pH, and presence of hydrophobic comonomers. Under acidic conditions, the cloud point falls below 0 °C for copolymers with between 25% to 60% ether content, because of the formation of hydrophobic H‐bonded ether–acid complexes. The cloud point also decreases with solution pH. For equivalent ether to acid ratios, the cloud point decreases with decreasing PEG chain length, because of the presence of a larger number of hydrophobic methyl and methacrylate groups. Similarly, the cloud point decreases upon incorporation of hydrophobic comonomers such as butyl, lauryl, or glycidyl methacrylates. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6095–6104, 2005     

Terpolymerization of methyl methacrylate, poly(ethylene glycol) methyl ether methacrylate or poly(ethylene glycol) ethyl ether methacrylate with methacrylic acid and sodium styrene sulfonate: determination of the reactivity ratios

Materials bearing ionic monomers were obtained through free radical terpolymerization of methyl methacrylate (MMA), poly(ethylene glycol) methyl ether methacrylate (PMEM) or poly(ethylene glycol) ethyl ether methacrylate (PEEM) with methacrylic acid (MA) and sodium styrene sulfonate (NaSS). The reactions were carried out in dimethyl sulfoxide using azobis(isobutyronitrile) as initiator. The reactivity ratios of the different couple of monomers were calculated according to the general copolymerization equation using the Finnemann-Ross, Kelen-Tüdos and Tidwell-Mortimer methods. The values of the reactivity ratios indicate that the different monomer units can be considered as randomly distributed along the chains for terpolymerizations of MMA, PMEM or PEEM with MA and NaSS. The average composition of the comonomers in the different terpolymers were calculated, showing a good agreement between the experimental and theoretical compositions. The instantaneous compositions are constant until about 70% of conversion. For higher conversions, the insertion of ionic monomers increases or decreases according to the system studied.     

Thermodynamic characteristics and the temperatures of relaxation transitions of poly(methacrylic acid)

The heat capacity of poly(methacrylic acid) containing 2.5 wt % water was measured in a vacuum adiabatic calorimeter at temperatures between 80 and 325 K. The heat capacity of anhydrous poly(methacrylic acid) was calculated, and its standard enthalpies of combustion and formation were determined. On the basis of the enthalpy of melting of the “free”-water phase, the limit of water solubility in the polymer was found calorimetrically at 273 K. The temperatures of relaxation transitions (the glass transition and the β and γ transitions) of poly(methacrylic acid) mixtures with water were determined via differential thermal analysis in the region 80–550 K. In addition, the determination of the temperatures of transitions of anhydrous poly(methacrylic acid) was performed via extrapolation to zero water content of the concentration dependences of the relaxation-transition temperatures.     

Thermal degradation of poly(ethyl methacrylate) and its copolymer with poly(ethyl acrylate)

The thermal degradation behaviour of poly(ethyl methacrylate) homopolymers and poly(ethyl methacrylate) and poly(ethyl acrylate) copolymers synthesized by using the benzoyl peroxide-di-methyl aniline redox pair at different temperatures (18–35C) was investigated. Contrary to some reports in the literature, the thermal degradation of PEMA was observed to take place in multi steps. These are assigned to be loss of labile end groups, side chain scission, anhydride formation and main chain degradation steps. Dominating chemical formations at the end of these steps were characterized by FTIR spectroscopy.The homopolymer samples synthesized at 18C showed a greater thermal stability against degradation. Copolymerization with small amounts of ethyl acrylate was observed to impart thermal stability to PEMA by stabilizing mainly the end groups against degradations.     

ESR spectra of poly(methacrylic acid) and poly(methyl methacrylate): Reinterpretation of the 9-line spectrum

The temperature dependence of the ESR spectra of poly(methacrylic acid) and poly-(methyl methacrylate) γ-irradiated at room temperature was studied between ?196°C and +25°C. The conventional 9-line spectrum was observed throughout this range with no significant spectral change, in contrast to the propagating radical ··· CH₂? °C(CH₃)COOR found in methacrylic acid monomer or barium methacrylate dihydrate irradiated at ?196°C. In addition, the irradiation of methacrylic acid monomer with a low dose at 0°C gave the same 13-line spectrum as that of the propagating radical obtained by the irradiation at ?196°C, while prolonged irradiation at 0°C gave the same conventional 9-line spectrum as that of poly(methacrylic acid) or poly(methyl methacrylate). The conventional 9-line spectrum has a much weaker 4-line component than that of the propagating radical. The difference comes from the surrounding matrix, and the conventional 9-line spectrum is well interpreted by introducing the concept of the distribution of the conformational angle in the irregular polymer matrix. From simulation of the ESR spectrum, it was found that the intensity of the 4-line component is very sensitive to the distribution, and that the observed 9-line spectrum is well reproduced assuming a Gaussian distribution (half-height width of 5–6°) around the most probable conformation which is nearly the same as that of the propagating radical, where the conformational angles of the two C? H_β bonds to the half-filled p-orbital are 55° and 65°.     

Complexation between poly(acrylic acid) and poly(vinylpyrrolidone): Influence of the molecular weight of poly(acrylic acid) and small molecule salt on the complexation

Poly(acrylic acid) (PAA) with different molecular weight and poly(vinylpyrrolidone) (PVP) were prepared by free radical polymerization using 2,2′-azoisobutyronitrile (AIBN) as initiator in anhydrous methanol for PAA, and in distilled water for PVP. Then, the complexation between PAA and PVP in aqueous solution was studied by UV transmittance measurement and fluorescence probe technique. The result shows that (1) at low pH, the formation of complexation between PAA and PVP bases on the intermacromolecular hydrogen bond and the composition of the formed complex is around 3:2 (the unit molar ratio of PAA to PVP) at pH 2.60 over the range of pH investigated. (2) The cooperative interaction through the formation of hydrogen bond among active sites plays an important role in complex formation, and depends on the pH of solution, the required minimum chain length of poly(acrylic acid). (3) The hydrogen bond is not affected by small molecular salt, which only affects those carboxylic groups without forming hydrogen bond on the PAA chain.     

Complexation between poly(methacrylic) and poly(acrylic) acids and star-shaped poly(ethylene glycol) based on pyrogallol

Complex formation between polymethacrylic (PMAA) and polyacrylic acids, and star-shaped poly(ethylene glycol) prepared by ethoxylation of pyrogallol (Pyr–PEG) has been studied viscometrically and by potentiometric titration in water solution. The competitive ability of Pyr–PEG and of the derivatives of the ethoxylation of phenol and hydroquinone in complex formation with PMAA has been compared by UV spectroscopy. Pyr–PEG turns out to be the weakest competitor because of its chemical structure. © 1996 John Wiley & Sons, Inc.     

Effect of cyclodextrins on pH-induced conformational transition of poly(methacrylic acid)

A pH-induced conformational transition of atactic poly(2-methylprop-2-enoic acid) (poly(methacrylic acid), PMMA) from the contracted to expanded conformation was investigated by viscometry, potentiometric titration, and anthracene solubilisation in the presence of low-molecular-mass non-ionogenic co-solutes-glucose, α-cyclodextrin (αCD), and γ-cyclodextrin (γCD), respectively. No effect of glucose and αCD on the conformational transition was observed with either of the methods used. On the other hand, the characteristic features of the conformational transition were absent in the presence of γCD. The different effects of the co-solutes indicate that the interaction between PMAA and γCD corresponds to the partial inclusion of the PMAA chain into the γCD cavity. The viscometry and anthracene solubilisation imply that γCD promotes the expanded conformation of PMAA at low pH. The potentiometric titration does not support this conclusion. Even though there is no break on the Henderson-Hasselbalch plot, a characteristic of the conformational transition, the potentiometric behaviour corresponds to that of the contracted PMMA conformation. Thus the results suggest the hierarchical picture of the PMAA conformation at low pH in which the local arrangement of the PMAA chain is a prerequisite for clustering on a larger scale.     

聚甲基丙烯酸乙酯的合成与性能研究

通过阴离子聚合反应合成了窄分子量分布(D=1．05-1．2)聚甲基丙烯酸乙酯CPEMA）。运用IR谱、^1HNMR和GPC等手段对合成产物进行了表征,探讨了影响甲基丙烯酸乙酯(EMA)阴离子聚合反应的因素,测定了该聚合物的玻璃化温度Tg,并研究了聚甲基丙烯酸乙酯在不同pH溶液中的降解性能。     

Molecular modeling of polymers. 10. Characterization of conformational transitions of poly(acrylic acid) and poly(methacrylic acid) using dyad structures

The conformational profiles of nearest side-chain neighbors, methylene-dyad structures, of poly(acrylic acid), PAA, and poly(methacrylic acid), PMA, were determined as a function of tacticity, extent of ionization, and presence of counterion. The dominant backbone conformer states are quite similar for both isotactic and syndiotactic diads in a common charge state. Thus, the overall dimensional properties of isotactic syndiotactic and atactic chains of PAA or PMA, based upon dyad interactions, are predicted to be alike for a given charge state. Significant deviations from precise t, g⁺, and g^? states are found for the dyad minimum energy conformations. The rod-to-coil and coil-to-rod transitions observed in PAA and PMA, respectively, as a function of increasing counterion concentration can be explained, to a large extent, by the conformational profiles of the corresponding dyad model structures. © 1994 John Wiley & Sons, Inc.