Polymerization of para-xylylene derivatives. VI. morphology of parylene N and parylene C films investigated by gas transport characteristics

Polychloro-p-xylylene (Parylene C) and poly-p-xylylene (Parylene N) films were synthesized in vacuum with and without the presence of 42 mtorr of argon at various deposition temperatures and three different dimer sublimation rates. Depending on the synthesis conditions, the morphology of the films can vary from a homogeneous (nonporous) structure to a heterogeneous (porous) structure. The transport coefficients of the gases He, O₂, N₂, and CO₂ through these films were measured at 25°C. The transport coefficients for both types of films vary with the deposition temperature and the dimer sublimation rate. The variation, however, cannot be solely explained by the change of crystallinity. Anomalous transport behavior is observed in the homogeneous, as-synthesized polymers of relatively high crystalline content (above 20–30%). In many cases the permeabilities and diffusivities increase despite an increase in crystallinity. The effects of crystallization induced by isothermal and solvent annealing on the transport coefficients of polymers of Parylene C are different from those of Parylene N synthesized with or without argon. The mean pore size and effective porosity of the porous films were calculated from gas permeation data. For Parylene C and Parylene N porous films synthesized without argon, increasing the dimer sublimation rate or decreasing the deposition temperature increases the mean pore size but decreases the effective porosity. For Parylene N porous films synthesized in the presence of argon, increasing the dimer sublimation rate or decreasing the deposition temperature results in a decrease in the mean pore size but an increase in the effective porosity. Overall, no appreciable change in transport coefficients is observed upon addition of an inert gas.     

Solvent-induced crystallization. I. Crystallization kinetics

The kinetics of crystallization of quenched poly(ethylene terephthalate) (PET) films during the imbibition of methylene chloride (MeCl₂) vapor is studied by density measurements. The effects of film thickness (0.0025–0.086 cm) and temperature (0–38°C) were examined. The data suggest that MeCl₂ transport controls the crystallization in thick films and at elevated temperatures, but that spherulite growth controls in thin films and at reduced temperatures. The application of a mathematical model developed previously supports this mechanistic interpretation of the data.     

Determination of accurate surface tensions of maleimide copolymers containing fluorinated side chain from contact angle measurements

Surface energetics of two fluorinated maleimide copolymers containing fluorinated side chain, i.e., poly(ethene-alt-N-(4-(perfluoroheptylcarbonyl)aminobutyl)maleimide) (ETMF) and poly(octadecene-alt-N-(4-(perfluoroheptylcarbonyl)aminobutyl)maleimide) (ODMF), are studied by contact angle measurements with 10 liquids consisting of fairly bulky molecules. Because of the inertness of octamethylcyclotetrasiloxane (OMCTS) and decamethylcyclopentasiloxane (DMCPS) molecules, their contact angles are used to determine the surface tension of the two polymers. It is found that other liquids show specific interactions with the ETMF films, and their contact angles deviate from a smooth curve that represents the surface tension of ETMF, i.e., 11.00 mJ/m². On ODMF surfaces, only OMCTS and DMCPS yield useful contact angles. Other liquids either dissolve the polymer film or show a slip-stick pattern. This finding is discussed in terms of interactions between segments of the polymer chains and the test liquids. OMCTS and DMCPS are suggested as the appropriate probe liquids, meeting specific criteria necessary for the determination of accurate surface tension of fluoropolymers.     

Synthesis and Characterization of Fluorinated Polyimide Derived from 3,3′‐Diisopropyl‐4,4′‐diaminodiphenyl‐3′′,4′′‐difluorophenylmethane

A novel aromatic diamine monomer, 3,3′‐diisopropyl‐4,4′‐diaminodiphenyl‐3′′,4′′‐difluorophenylmethane (PAFM), was successfully synthesized by coupling of 2‐isopropylaniline and 3,4‐difluorobenzaldehyde. The aromatic diamine was adopted to synthesize a series of fluorinated polyimides by polycondensation with various dianhydrides: pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride (ODPA) and 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride (BTDA) via the conventional one‐step method. These polyimides presented excellent solubility in common organic solvents, such as N,N‐dimethylformamide (DMF), N,N‐dimethyl acetamide (DMAc), dimethyl sulfoxide (DMSO), N‐methyl‐2‐pyrrolidone (NMP), chloroform (CHCl₃), tetrahydrofuran (THF) and so on. The glass transition temperatures (T_g) of fluorinated polyimides were in the range of 260–306°C and the temperature at 10% weight loss in the range of 474–502°C. Their films showed the cut‐off wavelengths of 330–361 nm and higher than 80% transparency in a wavelength range of 385–463 nm. Moreover, polymer films exhibited low dielectric properties in the range of 2.76–2.96 at 1 MHz, as well as prominent mechanical properties with tensile strengths of 66.7–97.4 MPa, a tensile modulus of 1.7–2.1 GPa and elongation at break of 7.2%–12.9%. The polymer films also showed outstanding hydrophobicity with the contact angle in the range of 91.2°–97.9°.     

Electrical,Optical, and Structural Properties of SnO2: F Films as a Function of Fluoride Precursor Concentration and Temperature

Atmospheric pressure chemical vapor deposition (APCVD) employing the precursor system of tin tetrachloride, ethyl formate, and 2,2,2‐trifluoroethyl trifluoroacetate vapors that were transported to hot glass substrates to deposit fluorine doped tin dioxide thin films. The system is optimized with respect to the substrate deposition temperature and to the amount of fluoride added to the precursor stream and the resultant structural, electrical and optical properties compared. Increasing the substrate temperature from 360 °C to 610 °C resulted in an approximately linear increase in thickness of the tin dioxide films. However, the resistivity decreased from 1.8 × 10^–2 Ω · cm at 360 °C to a minimum of 5.9 × 10^–4 Ω · cm at 560 °C and increased to 9.4 × 10^–4 Ω · cm at 610 °C. While maintaining a substrate temperature of 560 °C different amounts of fluorine precursor was introduced into the carrier stream, from 0 mL · h^–1 to 5 mL · h^–1, resulting in a decrease in resistivity (ρ) from 5.3 × 10^–2 Ω · cm at 0 mL · h^–1 to a minimum of 5.9 × 10^–4 Ω · cm at 2 mL · h^–1 and then increased to 1.0 × 10^–3 Ω · cm at 5 mL · h^–1. As the amount of fluoride is increased a concommittent increase in carrier concentration results until the point of overdoping the film produces an increase in scattering sites that increases resistivity. Best films were deposited at 560 °C and when the fluoride precursor flow rate was 2 mL · h^–1.     

Diffusion studies of poly(ethylene terephthalate) crystallized by nonreactive liquids and vapors

The diffusion of vapors and liquids which induce crystallization in initially amorphous, unoriented poly(ethylene terephthalate) (PET) films was studied. It was determined that these vapors and liquids penetrate the polymer as distinct fronts, and the kinetics of this penetration and the weight uptake kinetics both follow apparent Fickian behavior. Distinct cavitation advanced into the polymer at the penetrant front–dry polymer interface in certain PET–liquid systems, and phenomenological explanations of its existence and of the general diffusion process observed are offered. Finally, the diffusion of the highly interactive liquids dioxane and methylene chloride into cold-drawn PET was studied and shown to occur considerably more slowly than does the diffusion of these liquids into unoriented films.     

Effect of crystallization on the morphologies of block copolymer/homopolymer blends cast in an electric field

Blends of polystyrene (PS) and poly(styrene-b-ethylene oxide) (PS-b-PEO) were cast from a ternary solvent mixture containing 85% toluene, 10% tetrahydrofuran, and 5% methanol under conditions that favor crystallization of the PEO phase. Electric fields (2–14 kV/cm) were applied during casting to explore the possibility of morphology control by the field. It was observed that films cast in the absence of an electric field, in the temperature range of 0–25°C, from solutions initially cooled to 0°C were translucent. Their transmission electron micrographs exhibited thread-like, fibrillar structures. Micrographs of films cast in dc fields of 2–14 kV/cm at 16.3 ± 0.4°C also showed fibrillar structures, with the fibrils in the presence of fields greater than 8 kV/cm being substantially oriented in the field direction. We suggest that the morphologies developed under these conditions result from crystallization from preexisting crystal nuclei in the cooled solutions with the fibrillar crystals being oriented by the electric field. This method provides a possible way of processing anisotropic polymer blends. © 1996 John Wiley & Sons, Inc.     

Thin films of PS/PS‐b‐pnipam and ps/pnipam polymer blends with tunable wettability

We developed thin films of blends of polystyrene (PS) with the thermoresponsive polymer poly(N‐isopropylacrylamide) (PNIPAM) (PS/PNIPAM) and its diblock copolymer polystyrene‐b‐poly(N‐isopropylacrylamide) (PS/PS‐b‐PNIPAM) in different blend ratios, and we study their surface morphology and thermoresponsive wetting behavior. The blends of PS/PNIPAM and PS/PS‐b‐PNIPAM are spin‐casted on flat silicon surfaces with various drying conditions. The surface morphology of the films depends on the blend ratio and the drying conditions. The PS/PS‐b‐PNIPAM films do not show an increase in their water contact angles with temperature, as it is expected by the presence of the PNIPAM block. All PS/PNIPAM films show an increase in the water contact angle above the lower critical solution temperature of PNIPAM, which depends on the ratio of PNIPAM in the blend and is insensitive to the drying conditions of the films. The difference between the wetting behavior of PS/PS‐b‐PNIPAM and PS/PNIPAM films is due to the arrangement of the PNIPAM chains in the film. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 670–679     

Photochemical grafting of polysulfobetaine onto polyethylene and polystyrene surfaces and investigation of long‐term stability of the polysulfobetaine layer in seawater

Low‐density polyethylene (LDPE) and polystyrene (PS) films with hydrophilic surface were prepared by photochemical grafting of sulfobetaine‐based copolymer containing photolabile moiety, and long‐term stability of the hydrophilic nature of the surfaces in seawater was proved. The sulfobetaine‐based copolymer was prepared by copolymerization of N,N‐dimethyl‐N‐(3‐(methacryloylamino)propyl)‐N‐(3‐sulfopropyl) ammonium betaine with 2 or 5 mol% of N‐methacryloyl‐4‐azidoaniline, and the resulted polymers were grafted onto the plasma pretreated LDPE and PS films. The contact angle measurements were used to prove the modification as well as to follow the changes in the hydrophilicity during storage at room temperature under air atmosphere as well as in seawater at 32°C. The stability of the polymer layer was confirmed also by FTIR and AFM. Polysulfobetaine‐modified LDPE and PS surfaces exhibited significantly higher long‐term hydrophilicity compared with only plasma treated LDPE and PS surfaces.     

Preparation and properties of polysilsesquioxanes: Polysilsesquioxanes and flexible thin films by acid‐catalyzed controlled hydrolytic polycondensation of methyl‐ and vinyltrimethoxysilane

Polymethylsilsesquioxane (PMS) and polyvinylsilsesquioxane (PVS) were prepared by acid‐catalyzed controlled hydrolytic polycondensation of methyl‐ and vinyltrimethoxysilane (MTS and VTS), respectively. The spinnabilities and molecular weights of polysilsesquioxanes were easily controlled by the reaction conditions, such as the molar ratios of water, hydrochloric acid, and methanol to MTS or VTS; nitrogen flow rate; temperature; and stirring rate. PMS and PVS showed spinnability of more than 200 cm when their molecular weights were up to 42,000 (PMS) and 19,000 (PVS) M_w. Transparent, colorless, and flexible films of 0.02–0.10 mm thick were prepared by casting a 20 wt % acetone–methanol (V/V = 1) solution of PMS and PVS on a polymethylpentene shale, followed by heating at 80°C for 3 weeks. The tensile strength of the films, approximately 26 (PMS) and 17 (PVS) MPa, was found to be correlated with the structure of the polysilsesquioxanes. The surface contact angle and electroconductivity of films were also measured. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1017–1026, 1999     

NEW MATERIALS DERIVED FROM POLY(4-HYDROXYSTYRENE) AS LITHIUM BATTERY CELL COMPONENTS

A new class of polyethers has been prepared by the Mitsunobu coupling of poly(4-vinyl phenol), P4VP, with low molecular weight poly(ethylene glycol)methyl ether. These comb-like polymers, having ca. 20–30% residual phenols, were characterized by IR, DSC, and TGA. Results of thermal analysis on the polymers suggest thermal stability to at least 300°C and a glass transition temperature in the range ?30 to ?40°C. Complexes with LiPF₆ gave conductivities of ca. 1 × 10^?5 S/cm at room temperature. The polymers were blended with plasticized poly(vinylidene fluoride) (PVDF) to prepare porous films and subsequently infiltrated with lithium salts and ethylene and ethyl methyl carbonate. Ionic conductivities of these hybrid films were measured from ?20°C to 40°C. Conductivities as high as 2.4 × 10^?3 S/cm are observed at room temperature. The electrochemical stability of hybrid materials was studied by cyclic voltammetry.     

Cold crystallization and thermal shrinkage of uniaxially drawn poly(ethylene 2,6-naphthalate) by solid-state coextrusion

Solid-state coextrusion has been used to prepare uniaxially drawn films from isotropic poly(ethylene 2,6-naphthalate) (PEN) of a minimum degree of crystallinity (ca. 5%) both below and above its glass transition temperature T_g. The onset of cold crystallization (T_c) of the drawn films has been studied as a function of the extrusion temperature (ET) and the draw ratio (EDR). It has been shown that T_c decreases markedly on draw, as much as 95°C, and, at constant draw ratio T_c goes through a minimum in the T_g region. For undrawn PEN, annealing below 153°C has no significant effect on T_c. To evaluate the crystallization rate constant (k) and the activation energy (E_a) of the drawn specimens, a nonisothermal DSC procedure has been used. With increasing EDR, k increases markedly and E_a goes down over threefold compared with the undrawn polymer. At high ET, strain-induced crystallization has also been shown to play an important role in lowering E_a for cold crystallization. Thermal shrinkage above T_m indicates a high elastic recovery, underlining the efficiency of deformation, ca. 93%, achieved by solid-state coextrusion.     

A novel polymer gel electrolyte: Direct polymerization of ionic liquid from surface of silica nanoparticles

A novel polymer electrolyte is synthesized by directly grafting poly ionic liquids onto silica nanoparticles. The kinetic study of this surface‐initiated polymerization has also been included. A gel‐state electrolyte is formed by mixing this type of polymer/silica nanocomposite with ionic liquids under 60 °C, which exhibits an excellent conductivity of 0.8 mS/cm at room temperature and 14.7 mS/cm at 90 °C. In addition, the mechanism of gel formation has also been discussed in this article. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 121–127     

Synthesis and characterization of poly(urethane‐benzoxazine) films as novel type of polyurethane/phenolic resin composites

Poly(urethane‐benzoxazine) films as novel polyurethane ( PU )/phenolic resin composites were prepared by blending a benzoxazine monomer ( Ba ) and PU prepolymer that was synthesized from 2,4‐tolylene diisocyanate (TDI) and polyethylene adipate polyol (MW ca. 1000) in 2 : 1 molar ratio. DSC of PU/Ba blend showed an exotherm with maximum at ca. 246 °C due to the ring‐opening polymerization of Ba, giving phenolic OH functionalities that react with isocyanate groups in the PU prepolymer. The poly(urethane‐benzoxazine) films obtained by thermal cure were transparent, with color ranging from yellow to pale wine with increase of Ba content. All the films have only one glass transition temperature (T_g ) from viscoelastic measurements, indicating no phase separation in poly(urethane‐benzoxazine) due to in situ polymerization. The T_g increased with the increase of Ba content. The films containing 10 and 15% of Ba have characteristics of an elastomer, with elongation at break at 244 and 182%, respectively. These elastic films exhibit good resilience with excellent reinstating behavior. The films containing more than 20% of Ba have characteristics of plastics. The poly(urethane‐benzoxazine) films showed excellent resistance to the solvents such as tetrahydrofuran, N,N‐dimethyl formamide, and N‐methyl‐2‐pyrrolidinone that easily dissolve PU s. Thermal stability of PU was greatly enhanced even with the incorporation of a small amount of Ba . © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4165–4176, 2000     

Influence of RAFT end‐groups on the water swelling of poly(N‐propyl methacrylate)

The immersion of poly(n‐propyl methacrylate), PPMA, films (ca., 425 nm) in water induces swelling that is measured in‐situ using spectroscopic ellipsometry. Unexpectedly, the end group of the PPMA resulting from the reversible addition‐fragmentation chain transfer (RAFT) polymerization impacts the temperature dependence of swelling, despite their relatively high molecular weights (ca., 30 kDa). At 25 °C, dithiobenzoate terminated PPMA (PPMA‐DB) leads to significantly less swelling (5.6 vol %) than the dodecylsulfanylthiocarbonyl terminated PPMA (PPMA‐DD, 9.0 vol %). These PPMA films swell significantly more than expected due to a common carboxylic acid end group. As temperature is increased, the swelling for PPMA‐DB increases and that for PPMA‐DD decreases, with a crossover at approximately 35 °C–40 °C where the swelling is indistinguishable between the two polymers. The swelling kinetics exhibit two stages: an initial rapid swelling within the first minute of immersion and then a slow increase in thickness over multiple hours. The water contact angle of PPMA‐DB increases on heating, while the water contact angle of PPMA‐DD is invariant. This difference in the temperature dependence of the hydrophobicity is consistent with that for swelling. These results illustrate the potential unexpected consequences of residual RAFT fragment end groups on physical properties of polymers even at relatively high molecular weights. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 77–84     

Polyimide containing internal acetylene units linked para to the aromatic ring

4,4′-Diaminodiphenylacetylene (p-intA) was reacted with 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA), 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) and pyromellitic dianhydride (PMDA) in N-methyl-2-pyrrolidone (NMP) to give poly(amic acid) solution of moderate to high viscosity. Thermal imidization gave polyimide having acetylene units that are linked para to the aromatic connecting unit. Polyimide having acetylene units that are linked meta to the aromatic connecting unit also was prepared utilizing 3,3′-diaminodiphenylacetylene (m-intA) for comparison. The crosslinking behavior of the acetylene units was observed with DSC. Exotherm due to the crosslinking of the para-linked acetylene units appeared at ca. 340 to 380°C depending on the structure of polyimide, whereas meta-linked acetylene units appeared at lower temperature as 340–350°C. After thermal treatment at high temperature such as 350 or 400°C, the amount of the exotherm became smaller and finally disappeared on DSC, confirming the progress of crosslinking. Dynamic mechanical properties of the polyimide films show that glass transition temperature increased with higher heat treatment, also confirming the progress of crosslinking. Tensile properties of the polyimide films showed that rigid polyimide films consisting of p-intA with BPDA or PMDA have considerably higher modulus than those consisting of m-intA. Cold-drawing of the poly(amic acid) followed by imidization gave much higher modulus in the case of rigid polyimide. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2395–2402, 1997     

Thermo‐responsive glycopolymer chains grafted onto honeycomb structured porous films via RAFT polymerization as a thermo‐dependent switcher for lectin Concanavalin a conjugation

Stable and surface‐modified films with regular porous arrays were created by crosslinking honeycomb structured porous films prepared via breath figures from poly(styrene‐co‐maleic anhydride). The formation of open or closed pores of the films was controlled by the addition of a polyion complex. Subsequent crosslinking of the films with 1,8‐diaminooctane led to films, which maintain their structure in solvents. In addition, excess amino functionality after crosslinking allowed the attachment of RAFT agent, 3‐benzylsulfanyl thiocarbonyl sulfanylpropionic acid, for the controlled surface polymerization of N‐isopropyl acrylamide (NIPAAm) and N‐acryloyl glucosamine (AGA). The attachment of thermo‐responsive glycopolymers onto the honeycomb structured porous films was confirmed using contact angle measurements and confocal fluorescence microscopy. Cleavage of surface anchored polymers via aminolysis revealed that the molecular weights of the surface grafted chains are significantly larger than the molecular weight of the chains generated in solution. The honeycomb structured porous films with their grafted PNIPAAm‐ran‐PAGA polymer chains showed selective recognition of Concanavalin A (ConA). Below the lower critical solution temperature (LCST) of the surface, the conjugation is switched off, while above the LCST the surface grafted glucose moieties bind strongly to ConA. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3440–3455, 2010     

Reduction in the moisture absorption of cured MY720/DDS epoxy resins

Thin films of cured MY720/DDS epoxy resins were treated with blocking reagents for hydroxyl, amine, and epoxide functional groups. Infrared spectroscopy (IR) and differential scanning calorimetry (DSC) were used to monitor the progress of the reaction. Treated films were soaked in distilled water at 30°C for 720 h, and the corresponding moisture absorption determined gravimetrically. Samples treated with N-methyl-N-t-butyldimethylsilyl trifluroacetamide (MTBSTFA) containing 1% t-butyldimethylchlorosilane (TBDMCS) in dimethylsulfoxide (DMSO) at 30°C showed a maximum reduction in the IR peak at 3400 cm^?1 (OH and NH) of 39% and a 100% reduction in the epoxide peak at 904 cm, ^?1. The moisture absorption was 1.9%, a reduction of 58% compared to the untreated films (ca. 4.5%). The reactions show dependencies on time and temperature and are diffusion controlled. Samples treated with trimethylsilyl isocyanate (TMSI) in DMSO a 70°C showed 72% reduction in the 3400 cm^?1 IR peak; DSC thermograms do not show an exothermic energy, suggesting that all epoxide groups reacted. These reactions are primarily dependent on time and temperature. The moisture absorption of TMSI treated samples was 1.0% (75% reduction). Samples were also treated with m-trifluoromethyl phenyliscyanate (MTFPI). The reduction in the IR peak at 3400 cm^?1 was 9%, but the moisture absorption was 2.4%—a reduction of 47%.     

Low‐rate dynamic contact angles on poly(methyl methacrylate/ethyl methacrylate, 30/70) and the determination of solid surface tensions

Low‐rate dynamic contact angles of 12 liquids on a poly(methyl methacrylate/ethyl methacrylate, 30/70) P(MMA/EMA, 30/70) copolymer were measured by an automated axisymmetric drop shape analysis‐profile (ADSA‐P). It was found that five liquids yield nonconstant contact angles, and/or dissolve the polymer on contact. From the experimental contact angles of the remaining seven liquids, it is found that the liquid–vapor surface tension times cosine of the contact angle changes smoothly with the liquid–vapor surface tension (i.e., γ_l|Kv cos θ depends only on γ_l|Kv for a given solid surface or solid surface tension). This contact angle pattern is in harmony with those from other methacrylate polymer surfaces previously studied.^45,50 The solid–vapor surface tension calculated from the equation‐of‐state approach for solid–liquid interfacial tensions¹⁴ is found to be 35.1 mJ/m², with a 95% confidence limit of ± 0.3 mJ/m², from the experimental contact angles of the seven liquids. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2039–2051, 1999     

poly(4,4′-oxybibenzoate): Polymerization,morphology, transitions,and crystal structures

4-Acetoxy 4′-carboxy biphenyl has been polymerized from solution, the bulk melt, and in constrained thin films, all below the melting point of the monomer as measured by differential scanning calorimetry (DSC). An isothermal sublimation–recrystallization–melting (and chemical change)–polymerization–crystallization process is proposed. From solution and in the thin films, single crystals consisting of ca. 100 Å thick lamellae are observed, with evidence for monomer addition–reaction on the end (top and bottom) surfaces. The bulk samples are fibrous, the “fibers” consisting of whisker-like single crystals. The polymer is highly heat and radiation (electron beam) resistant, with numerous successive electron diffraction (ED) patterns from the same crystal or sheared sample permitting comparison of the changes in ED patterns with transitions seen by DSC at ca. 350, 530, and 590°C. Phase I (a = 7.8, b = 5.5, c = 10.8 Å), a possible phase II (a = 15.6, b = 3.6 Å c = unknown), and a phase III (a = 9.0, b = 5.2 = √3a, c = 10.8 Å). Phases I and II are seen in samples polymerized at temperatures at and below 310°C; phase III is observed in samples polymerized at and above 350°C and in sheared samples. © 1993 John Wiley & Sons, Inc.