Selective vinyl cationic polymerization of monomers with two cationically polymerizable groups. II. p-vinylphenyl glycidyl ether: An epoxy-functionalized styrene

p-Vinylphenyl glycidyl ether (VPGE), a styrene derivative with an epoxy pendant, was polymerized by various cationic initiators, and its selective vinyl polymerization was investigated at low temperatures below ?15°C. BF₃OEt₂ (a metal halide) and CF₃SO₃H (a strong protonic acid) polymerized both vinyl and epoxy groups of VPGE, and produced cross-linked insoluble polymers. The HI/I₂ initiating system and iodine, in contrast, polymerized its vinyl group in polar solvents (CH₂Cl₂ and nitroethane) highly selectively in the temperature range of ?15 to ?40°C to give soluble polymers with a polystyrene backbone and epoxy pendants; however, under these conditions, 10–15% of the epoxy groups of the polymers were consumed during the polymerization by the reaction with the growing species. The polymerization by HI/I₂ in CH₂CI₂ involved a long-lived propagating species, as indicated by a progressive increase in the molecular weight (M?_n) of the polymers with monomer conversion and their fairly narrow molecular weight distributions (M?_w/M?_n ～ 1.6). The differences between the polymerizations of VPGE and p-isopropenylphenyl glycidyl ether, an α-methylstyrene-type counterpart of VPGE, were also discussed with an emphasis on the effects of the α-methyl group in the latter monomer.     

Living cationic polymerization of isobutyl propenyl ether as β-substituted vinyl ether

Isobutyl propenyl ether [IBPE; CH₃CH=CH? OCH₂CH(CH₃)₂] was polymerized with a mixture of hydrogen iodide and iodine (HI/I₂ initiator) in n-hexane at ?40°C to yield living polymers with a nearly monodisperse molecular weight distribution (MWD) (M?_w/M?_n ≈ 1.1). The number-average molecular weight (M?_n) of the polymers increased proportionally to IBPE conversion and further increased when a new monomer feed was added to a completely polymerized solution. The M?_n was controlled by the initial concentration of hydrogen iodide if the acid was charged in excess over iodine. In polymerization by iodine alone the M?_n of the polymers obtained in nonpolar solvents (n-hexane and toluene) also increased with conversion, but their MWD was broader (M?_w/M?_n = 1.3–1.4) than in the HI/I₂-initiated systems under similar conditions. The iodine-initiated polymerization in polar CH₂Cl₂ solvent, in contrast, led to nonliving polymers with a broad MWD (M?_n/M?_n = 1.6–1.8) and M?_n, independent of conversion. The living polymerization of IBPE was also compared with that of the corresponding isobutyl vinyl ether, to determine the effect of the β-methyl group in IBPE.     

Living cationic polymerization of 2-vinyloxyethyl phthalimide: Synthesis of poly(vinyl ether) with pendant primary amino functions

Cationic polymerization of 2-vinyloxyethyl phthalimide ( 1 ) in CH₂Cl₂ at ?15°C with hydrogen iodide/iodine (HI/I₂) as initiator led to living polymers of a narrow molecular weight distribution (M?_w/M?_n = 1.1–1.25). The number-average molecular weight of the polymers was in direct proportion to monomer conversion and could be controlled in the range of 1000–6000 by regulating the 1 /HI feed ratio. However, when a fresh monomer was supplied to the completely polymerized reaction mixture, the molecular weight of the polymers was not directly proportional to monomer conversion. The polymerization of 1 by boron trifluoride etherate (BF₃OEt₂) in CH₂Cl₂ at ?78°C gave polymers with relatively high molecular weight (M?_w > 20,000) and broad molecular weight distribution (M?_w/M?_n ～ 2). The HI/I₂-initiated polymerization of 1 was an order of magnitude slower than that of ethyl vinyl ether, probably because of the electron-withdrawing phthalimide pendant. Hydrazinolysis of the imide functions in poly( 1 ) gave a water-soluble poly(vinyl ether) ( 3 ) with aliphatic primary amino pendants.     

Living cationic polymerization of vinyl ethers with a urethane group

To study the possibility of living cationic polymerization of vinyl ethers with a urethane group, 4‐vinyloxybutyl n‐butylcarbamate ( 1 ) and 4‐vinyloxybutyl phenylcarbamate ( 2 ) were polymerized with the hydrogen chloride/zinc chloride initiating system in methylene chloride solvent at ?30 °C ([monomer]₀ = 0.30 M, [HCl]₀/[ZnCl₂]₀ = 5.0/2.0 mM). The polymerization of 1 was very slow and gave only low‐molecular‐weight polymers with a number‐average molecular weight (M_n) of about 2000 even at 100% monomer conversion. The structural analysis of the products showed occurrence of chain‐transfer reactions because of the urethane group of monomer 1 . In contrast, the polymerization of vinyl ether 2 proceeded much faster than 1 and led to high‐molecular‐weight polymers with narrow molecular weight distributions (MWDs ≤ ～1.2) in quantitative yield. The M_n's of the product polymers increased in direct proportion to monomer conversion and continued to increase linearly after sequential addition of a fresh monomer feed to the almost completely polymerized reaction mixture, whereas the MWDs of the polymers remained narrow. These results indicated the formation of living polymer from vinyl ether 2 . The difference of living nature between monomers 1 and 2 was attributable to the difference of the electron‐withdrawing power of the carbamate substituents, namely, n‐butyl for 1 versus phenyl for 2 , of the monomers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2960–2972, 2004     

Living cationic polymerization of p-alkoxystyrenes by free ionic species

In contrast to the common view, living cationic polymerization of p-methoxy- and p-t-butoxystyrenes proceeded in polar solvents such as EtNO₂/CH₂Cl₂ mixtures, and involvement of free ionic growing species therein was examined. For example, the two alkoxystyrenes were polymerized with the isobutyl vinyl ether-HCl adduct/ZnCl₂ initiating system at −15°C in such polar solvents as CH₂Cl₂ or EtNO₂/CH₂Cl₂ [1/1 (v/v)], as well as toluene. The number average molecular weight (M̄_n) of the polymers increased in direct proportion to the monomer conversion, even after sequential monomer addition, and the molecular weight distribution (MWD) stayed very narrow throughout the reaction. In addition, the M̄_n agreed with the calculated values, assuming that one adduct molecule generates one living polymer chain. In these polar media the addition of a common ion salt retarded the polymerization, indicating that dissociated ionic species are involved in the propagating reaction. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3694–3701, 1999     

Living cationic polymerization of α‐methyl vinyl ethers using SnCl4

Cationic polymerization of α‐methyl vinyl ethers was examined using an IBEA‐Et_1.5AlCl_1.5/SnCl₄ initiating system in toluene in the presence of ethyl acetate at 0 ～ ?78 °C. 2‐Ethylhexyl 2‐propenyl ether (EHPE) had a higher reactivity, compared to corresponding vinyl ethers. But the resulting polymers had low molecular weights at 0 or ?50 °C. In contrast, the polymerization of EHPE at ?78 °C almost quantitatively proceeded, and the number‐average molecular weight (M_n) of the obtained polymers increased in direct proportion to the EHPE conversion with quite narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight ≤ 1.05). In monomer‐addition experiments, the M_n of the polymers shifted higher with low polydispersity as the polymerization proceeded, indicative of living polymerization. In the polymerization of methyl 2‐propenyl ether (MPE), the living‐like propagation also occurred under the reaction conditions similar to those for EHPE, but the elimination of the pendant methoxy groups was observed. The introduction of a more stable terminal group, quenched with sodium diethyl malonate, suppressed this decomposition, and the living polymerization proceeded. The glass transition temperature of the obtained poly(MPE) was 34 °C, which is much higher than that of the corresponding poly(vinyl ether). This poly(MPE) had solubility characteristics that differed from those of poly(vinyl ethers). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2202–2211, 2008     

Evidence for chain transfer in the atom transfer radical polymerization of butyl acrylate

Poly(butyl acrylate) (PBuA) of high molecular weight was synthesized by atom transfer radical polymerization (ATRP) in ethyl acetate. Whereas for low molecular weight polymers, a linear increase of the number‐average molecular weight, M_n, versus conversion and narrow molecular weight distributions indicate the suppression of side reactions, a downward curvature in the plot of M_n versus conversion was observed for high molecular weights (M_n > 50 000). This effect is explained by chain transfer reactions, leading to branched polymers. GPC measurements with a viscosity detector give evidence for the branched structure of high molecular weight polymers obtained in ATRP. In addition, transfer to solvent or monomer is likely to occur.     

Studies on propagating species in cationic polymerization of styrene derivatives by acetyl perchlorate or iodine. IV. Common-ion salt effect on the polymerization rate and the steric structure of the polymer obtained by acetyl perchlorate

Effects of a common-ion salt, n-Bu₄NClO₄, on the cationic polymerization of styrene and p-chlorostyrene by acetyl perchlorate were studied in a variety of solvents at 0°C. In polymerization (in CH₂Cl₂) which yielded polymers with a bimodal molecular weight distribution (MWD), addition of the salt suppressed the formation of higher polymers, but affected neither the molecular weight nor the steric structure of the lower polymers. The polymerization rate decreased with increasing salt concentration and became constant at or above a certain concentration. In nitrobenzene, on the other hand, the MWD of the polymers was unimodal and steric structure was unchanged even in the presence of salt at a concentration 50 times that of the catalyst. However, the polymerization rate and the polymer molecular weight decreased monotonically as salt concentration increased. On the basis of these results, it was concluded that the ion pair in methylene chloride differs from that in nitrobenzene, and that the species in the latter solvent is similar in nature to free ions. The fractional contribution of the dissociated and nondissociated propagating species to polymer formation was determined from the rate depression caused by addition of the salt.     

Solvent effects on the polymerization of multi-armed vinyl biphenyl derivatives containing pendant oligo(oxyethylene)cyclotriphosphazenes

Polymerization of vinyl biphenyl derivatives containing a pendant oligo(oxyethylene)cyclotriphosphazene (VBMEP, ? (OCH₂CH₂)nOCH₃, n = 1; VBDEP, n = 2; VBTEP, n = 3) was carried out in various solvents. The conversions of these monomers increased with increasing β values, solvent hydrogen bond acceptor abilities, indicating that the hydrogen bond formation is the most important factor in the polymerization. ¹³CNMR study showed that the reactivity of the monomer is influenced by the hydrogen bond interaction. In ethanol, the kinetic orders of monomer and initiator concentrations for the polymerization of VBDEP were different from those in 1,2-dichloroethane (DCE), which suggest the predominant occurrence of primary radical termination. The intrinsic viscosity of poly(VBDEP) with M?_n = 22 000 in DCE was two times higher than that in ethanol, and plots of intrinsic viscosity versus conversion of VBDEP gave a straight line. The results suggest that the polymer chains in ethanol are in a coiled conformation, whereas in DCE they are in a relatively extended structure, and that the propagation is affected by the conformational change. These behaviors originated from the hydrogen bond formation between polymers and solvents are discussed. The copolymerization of styrene with multiarmed monomers and the properties of polycascade polymers obtained are also described. © 1993 John Wiley & Sons, Inc.     

Living cationic polymerization of vinyl ethers with a functional group. VII. Polymerization of vinyl ethers with a silyloxyl group and synthesis of polyalcohols and related functional polymers

Living cationic polymerizations of two silicon-containing vinyl ethers, 2-(t-butyldimethyl-silyloxyl)ethyl vinyl ether (tBuSiVE) and 2-(trimethylsilyloxyl)ethyl vinyl ether (MeSiVE), have been achieved with use of the hydrogen iodide/iodine (HI/I₂) initiating system in toluene at ?15 or ?40°C, despite the existence of the acid-sensitive silyloxyl pendants. The living nature of the polymerizations was demonstrated by linear increases in the number-average molecular weights (M?_n) of the polymers in direct proportion to monomer conversion and by their further rise upon addition of a second monomer feed to a completely polymerized reaction mixture. The polymers obtained in these experiments all exhibited very narrow molecular weight distributions (MWD) with M?_w/M?_n around or below 1.1. Desilylation of the polymers under mild conditions (with H⁺ for MeSiVE and F^? for tBuSiVE) gave poly(2-hydroxyethyl vinyl ether), a water-soluble polyalcohol with a narrow MWD. The living processes also permitted clean syntheses of amphiphilic AB block copolymers and water-soluble methacrylate-type macromonomers, all of which bear narrowly distributed segments of the polyalcohol derived from the silicon-containing vinyl ethers.     

Free-radical polymerization of a reducing vinyl sugar ester in dimethylformamide and water

To develop a new synthetic polymer containing sugar branches, radical polymerization of the reducing vinyl sugar ester 6-O-vinyladipoyl-D -glucose ( 1 ) was performed in an organic solvent or in water. The polymers obtained with several azoinitiators in dimethylformamide (DMF) showed comparatively low average molecular weight (M̄_n ≈ 4500). In contrast, the use of a redox initiator (FeSO₄ and H₂O₂) in water gave polymers of higher average molecular weight (M̄_n ≈ 33000) in higher yield (90%), followed by crosslinking at high conversions.     

Synthesis of linear and starlike polymers from poly(propylene glycol) methacrylate using controlled radical polymerization

The copper‐catalyzed atom transfer radical polymerization (ATRP) of poly(propylene glycol) methacrylate (PPGM) in solution to produce linear and starlike polymers is reported, using methylethyl ketone as the solvent and a temperature of 80 °C. The ATRP system used was efficient for polymerization of the functionalized monomer without protecting hydroxyl end groups of monomer. The polymerizations were consistent with “living” or controlled processes, as revealed by the linear evolution of molecular weight with conversion. Increasing the [M]₀:[I]₀ ratio resulted in increasing molecular weights, whereas the polydispersity indices remained low (M_w/M_n < 1.4) even at high conversion. Decreasing the [CuBr]₀:[I]₀ ratio resulted in lower conversions, slightly larger polydispersities, and decreased molecular weights, likely resulting from a lower initiation efficiency. Polymers were characterized by ¹H and ¹³C NMR; molecular weights of polymers with low degrees of polymerization were estimated by end‐group analysis from ¹³C NMR spectra obtained using distortionless enhancement by polarization transfer and the gated decoupling techniques. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 334–343, 2002     

Synthesis of PMMA‐b‐PBA block copolymer in homogeneous and miniemulsion systems by DPE controlled radical polymerization

In this research, poly(methyl methacrylate)‐b‐poly(butyl acrylate) (PMMA‐b‐PBA) block copolymers were prepared by 1,1‐diphenylethene (DPE) controlled radical polymerization in homogeneous and miniemulsion systems. First, monomer methyl methacrylate (MMA), initiator 2,2′‐azobisisobutyronitrile (AIBN) and a control agent DPE were bulk polymerized to form the DPE‐containing PMMA macroinitiator. Then the DPE‐containing PMMA was heated in the presence of a second monomer BA, the block copolymer was synthesized successfully. The effects of solvent and polymerization methods (homogeneous polymerization or miniemulsion polymerization) on the reaction rate, controlled living character, molecular weight (M_n) and molecular weight distribution (PDI) of polymers throughout the polymerization were studied and discussed. The results showed that, increasing the amounts of solvent reduced the reaction rate and viscosity of the polymerization system. It allowed more activation–deactivation cycles to occur at a given conversion thus better controlled living character and narrower molecular weight distribution of polymers were demonstrated throughout the polymerization. Furthermore, the polymerization carried out in miniemulsion system exhibited higher reaction rate and better controlled living character than those in homogeneous system. It was attributed to the compartmentalization of growing radicals and the enhanced deactivation reaction of DPE controlled radical polymerization in miniemulsified droplets. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4435–4445, 2009     

A novel tridentate nitrogen donor as ligand in copper catalyzed ATRP of methyl methacrylate

A tridentate ligand, BPIEP: 2,6‐bis[1‐(2,6‐diisopropyl phenylimino) ethyl] pyridine, having central pyridine unit and two peripheral imine coordination sites was effectively employed in controlled/“living” radical polymerization of MMA at 90°C in toluene as solvent, Cu^IBr as catalyst, and ethyl‐2‐bromoisobutyrate (EBiB) as initiator resulting in well‐defined polymers with polydispersities M_w/M_n ≤ 1.23. The rate of polymerization follows first‐order kinetics, k_app = 3.4 × 10^?5 s^?1, indicating the presence of low radical concentration ([P*] ≤ 10^?8) throughout the reaction. The polymerization rate attains a maximum at a ligand‐to‐metal ratio of 2:1 in toluene at 90°C. The solvent concentration (v/v, with respect to monomer) has a significant effect on the polymerization kinetics. The polymerization is faster in polar solvents like, diphenylether, and anisole, as compared to toluene. Increasing the monomer concentration in toluene resulted in a better control of polymerization. The molecular weights (M_n,SEC) increased linearly with conversion and were found to be higher than predicted molecular (M_n,Cal). However, the polydispersity remained narrow, i.e., ≤1.23. The initiator efficiency at lower monomer concentration approaches a value of 0.7 in 110 min as compared to 0.5 in 330 min at higher monomer concentration. The aging of the copper salt complexed with BPIEP had a beneficial effect and resulted in polymers with narrow polydispersitities and higher conversion. PMMA obtained at room temperature in toluene (33%, v/v) gave PDI of 1.22 (M_n = 8500) in 48 h whereas, at 50°C the PDI is 1.18 (M_n = 10,300), which is achieved in 23 h. The plot of lnk_app versus 1/T gave an apparent activation energy of polymerization as (ΔE^≠_app) 58.29 KJ/mol and enthalpy of equilibrium (ΔH⁰_eq) to 28.8 KJ/mol. Reverse ATRP of MMA was successfully performed using AIBN in bulk as well as solution. The controlled nature of the polymerization reaction was established through kinetic studies and chain extension experiments. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4996–5008, 2005     

Living cationic polymerization of p-methylstyrene by hydrogen iodide/zinc halide initiating systems

Living cationic polymerization of p-methylstyrene has been investigated with use of hydrogen iodide/zinc halide initiating systems (HI/ZnX₂; X = Cl, I) in toluene and methylene chloride solvents. The best results were obtained with HI/ZnCl₂ below 0°C where the zinc salt was employed in excess over hydrogen iodide (HI/ZnCl₂ = 1/5 molar ratio). Under these conditions, the number-average molecular weights $ \left( {\overline {M_n } } \right)$ of the produced polymers increased proportionally to monomer conversion, further increased upon addition of fresh feeds of p-methylstyrene into completely polymerized reaction mixtures, and were in good agreement with the calculated values assuming that one living polymer chain forms per molecule of hydrogen iodide; the molecular weight distributions (MWDs) of the polymers were fairly narrow $ \left( {{{\overline {M_w } } \mathord{\left/ {\vphantom {{\overline {M_w } } {\overline {M_n } }}} \right. \kern-\nulldelimiterspace} {\overline {M_n } }} = 1.1 - 1.3} \right) $ throughout these processes. In contrast, when equimolar mixtures of hydrogen iodide and zinc chloride or iodide were employed, the polymerizations were rather slow even in methylene chloride at +25°C, and the product polymers exhibited bimodal MWDs, the lower-molecular weight fraction of which was mediated by long-lived growing species. Addition of tetra-n-butylammonium iodide as a common ion salt (nBu₄NI/HI = 1/200 molar ratio) led to unimodal MWDs consisting of the long-lived lower polymer fraction alone.     

Ruthenium‐catalyzed fast living radical polymerization of methyl methacrylate: The R?Cl/Ru(Ind)Cl(PPh3)2/n‐Bu2NH initiating system

A fast living radical polymerization of methyl methacrylate (MMA) proceeded with the (MMA)₂? Cl/Ru(Ind)Cl(PPh₃)₂ initiating system in the presence of n‐Bu₂NH as an additive [where (MMA)₂? Cl is dimethyl 2‐chloro‐2,4,4‐trimethyl glutarate]. The polymerization reached 94% conversion in 5 h to give polymers with controlled number‐average molecular weights (M_n's) in direct proportion to the monomer conversion and narrow molecular weight distributions [MWDs; weight‐average molecular weight/number‐average molecular weight (M_w/M_n) ≤ 1.2]. A poly(methyl methacrylate) with a high molecular weight (M_n ～ 10⁵) and narrow MWD (M_w/M_n ≤ 1.2) was obtained with the system within 10 h. A similarly fast but slightly slower living radical polymerization was possible with n‐Bu₃N, whereas n‐BuNH₂ resulted in a very fast (93% conversion in 2.5 h) and uncontrolled polymerization. These added amines increased the catalytic activity through some interaction such as coordination to the ruthenium center. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 617–623, 2002; DOI 10.1002/pola.10148     

Living cationic polymerization of 2‐adamantyl vinyl ether

Living cationic polymerization of 2‐adamantyl vinyl ether (2‐vinyloxytricyclo[3.3.1.1]^3,7decane; 2‐AdVE) was achieved with the CH₃CH(OiBu)OCOCH₃/ethylaluminum sesquichloride/ethyl acetate [CH₃CH(OiBu)OCOCH₃/Et_1.5AlCl_1.5/CH₃COOEt] initiating system in toluene at 0 °C. The number‐average molecular weights (M_n's) of the obtained poly(2‐AdVE)s increased in direct proportion to monomer conversion and produced the polymers with narrow molecular weight distributions (MWDs) (M_w/M_n = ～1.1). When a second monomer feed was added to the almost polymerized reaction mixture, the added monomer was completely consumed and the M_n's of the polymers showed a direct increase against conversion of the added monomer. Block and statistical copolymerization of 2‐AdVE with n‐butyl vinyl ether (CH₂?CH? O? CH₂ CH₂CH₂CH₃; NBVE) were possible via living process based on the same initiating system to give the corresponding copolymers with narrow MWDs. Grass transition temperature (T_g) and thermal decomposition temperature (T_d) of the poly(2‐AdVE) (e.g., M_n = 22,000, M_w/M_n = 1.17) were 178 and 323 °C, respectively. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1629–1637, 2008     

Living cationic polymerization of vinyl ether with a cyclic acetal group

The living cationic polymerization of 5‐ethyl‐2‐methyl‐5‐(vinyloxymethyl)‐1,3‐dioxane ( 1 ), a vinyl ether with a cyclic acetal unit, was investigated with various initiating systems in toluene or methylene chloride at 0 to ?30 °C. With initiating systems such as hydrogen chloride (HCl)/zinc chloride (ZnCl₂), isobutyl vinyl ether–acetic acid adduct [CH₃CH(OiBu)OCOCH₃]/tin tetrabromide (SnBr₄)/di‐tert‐butylpyridine (DTBP), and CH₃CH(OiBu)OCOCH₃/ethylaluminum sesquichloride (Et_1.5AlCl_1.5)/ethyl acetate (CH₃COOEt), the number‐average molecular weights (M_n's) of the obtained poly( 1 )s increased in direct proportion to the monomer conversion and produced polymers with relatively narrow molecular weight distributions [MWDs; weight‐average molecular weight/number‐average molecular weight (M_w/M_n) = 1.2–1.3]. To investigate the living nature of the polymerization with CH₃CH(OiBu)OCOCH₃/SnBr₄/DTBP, a second monomer feed was added to the almost polymerized reaction mixture. The added monomer was completely consumed, and the M_n values of the polymers showed a direct increase against the conversion of the added monomer, indicating the formation of a long‐lived propagating species. The glass transition temperature and thermal decomposition temperature of poly( 1 ) (e.g., M_n = 13,600, M_w/M_n = 1.30) were 29 and 308 °C, respectively. The cyclic acetal group in the pendants of the polymer of 1 could be converted to the corresponding two hydroxy groups in a 65% yield by an acid‐catalyzed hydrolysis reaction. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4855–4866, 2007     

Living cationic polymerization of vinyl ethers with carboxylic acid/tin tetrahalide initiating systems. I. New initiating systems based on acetic acid and selection of Lewis acid and basic additive leading to living polymers with low polydispersity

Cationic polymerization of isobutyl vinyl ether (IBVE) with acetic acid (CH₃COOH)/tin tetrahalide (SnX₄: X = Cl, Br, I) initiating systems in toluene solvent at 0°C was investigated, and the reaction conditions for living polymerization of IBVE with the new initiating systems were established. Among these tin tetrahalides, SnBr₄ was found to be the most suitable Lewis acid to obtain living poly(IBVE) with a narrow molecular weight distribution (MWD). The polymerization with the CH₃COOH/SnBr₄ system, however, was accompanied with the formation of a small amount of another polymer fraction of very broad MWD, probably due to the occurrence of an uncontrolled initiation by SnBr₄ coupled with protonic impurity. Addition of 1,4-dioxane (1–1.25 vol %) or 2,6-di-tert-butylpyridine (0.1–0.6mM) to the polymerization mixture completely eliminated the uncontrolled polymer to give only the living polymer with very narrow MWD (M _w/M _n ≤ 1.1; M _w, weight-average molecular weight; M _n, number-average molecular weight). The M _n of the polymers increased in direct proportion to monomer conversion, continued to increase upon sequential addition of a fresh monomer feed, and was in good agreement with the calculated values assuming that one CH₃COOH molecule formed one polymer chain. Along with these results, kinetic study and direct ¹H-NMR observation of the living polymerization indicated that CH₃COOH and SnBr₄ act as so-called “initiator” and “activator”, respectively, and the living polymerization proceeds via an activation of the acetate dormant species. The basic additives such as 1,4-dioxane and 2,6-di-tert-butylpyridine would serve mainly as a “suppressor” of the uncontrolled initiation by SnBr₄. The polymers produced after quenching the living polymerization with methanol possessed the acetate dormant terminal and they induced living polymerization of IBVE in conjunction with SnBr₄ in the presence of 1,4-dioxane. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3173–3185, 1998     

Living polymerization of isobutyl vinyl ether by HI/I2 initiator in polar solvents

This study has shown a nearly perfect living polymerization of isobutyl vinyl ether (IBVE) to proceed not only in nonpolar media (e.g., n-hexane) but in relatively polar CH₂Cl₂ solvent, provided that the HI concentration is sufficiently high. The produced polymers had a nearly monodisperse molecular weight distribution (M _w/M _n ≤ 1.1); the number-average molecular weight (M _n) increased in direct proportion to IBVE conversion and its increase continued on the addition of a fresh feed of the monomer at the end of the polymerization. The use of a more polar medium (PhNO₂/CH₂Cl₂) or a lower HI concentration leads to chain transfer reactions, by promoting the ionic dissociation of the “nondissociated” living propagating species. The successful living polymerization by HI/I₂ in CH₂Cl₂ indicates a very strong interaction between the iodide anion and the growing end.