Dilation and plasticization of polystyrene by carbon dioxide

We have used an optical interference technique to measure the dilation of polystyrene films in the presence of carbon dioxide or helium at pressures up to 20 atm. Dilation isotherms (plots of dilation versus gas pressure at constant temperature) were obtained for three samples of polystyrene which had widely differing molecular weights. The dilation isotherms have the same general shape as sorption isotherms, which means that all of the sorbed gas molecules contribute to volume dilation and non can be thought of as occupying molecular-sized voids in the polymer. Using sorption results from the literature we show that the partial molar volume of CO₂ at 35°C is about 39 cm³ mol^?1 and appears to be independent of polystyrene molecular weight. For a polystyrene sample with M_n = 3600, the partial molar volume of sorbed CO₂ increases to 44 and 50 cm³ mol^?1 at 45 and 55°C, respectively. The sorption of CO₂ in polystyrene is shown to depress the glass transition temperature of the mixture, consistent with theoretical predictions. The shape of the dilation and sorption isotherms are consistent with the depression of the glass transition temperature.     

Sorptive dilation of polysulfone and poly(ethylene terephthalate) films by high-pressure carbon dioxide

Dilation of polysulfone (PSUL) and crystalline poly(ethylene terephthalate) (PET) films accompanying sorption of carbon dioxide is measured by a cathetometer under high pressure up to 50 atm over the temperature range of 35–65°C. Sorptive dilation isotherms of PSUL are concave and convex to the pressure and concentration axes, respectively, and both isotherms exhibit hysteresis. Each dilation isotherm plotted versus pressure and concentration for the CO₂-PET system shows an inflection point, i.e., a glass transition point, at which the isotherm changes from a nonlinear curve to a straight line. Dilation isotherms of PET below the glass transition point are similar to those of the CO₂-PSUL system, whereas the isotherms above the glass transition point are linear and exhibit no hysteresis. Partial molar volumes of CO₂ in these polymers are determined from data of sorptive dilation. On the basis of the extended dual-mode sorption model and the current data, primitive equations for gas-sorptive dilation of glassy polymers are proposed.     

Sorption and partial molar volumes of gases in poly(ethylene-co-vinyl acetate)

Sorption and dilation properties of polymer-gas systems involving poly(ethylene-co-vinyl acetate) and N₂, CH₄, or CO₂, have been investigated at pressures up to 50 atm at temperatures of 10–40°C. Sorption isotherms for low-solubility gases (i.e., CH₄ and N₂) can be described by Henry's law, and those for high-solubility gas (i.e., CO₂) by Flory-Huggins dissolution equation. Dilation isotherms are similar in contour to the corresponding sorption isotherms. From the obtained sorption and dilation data, partial molar volumes of the gases in the polymer were determined as a function of temperature. Thermal expansivity of dissolved CO₂ molecules was estimated at ca. 2.4 × 10^?3°C^?1 from the temperature dependence of partial molar volume. The expansivity is smaller than that of liquid CO₂ and larger than those of the polymer and organic liquids. © 1994 John Wiley & Sons, Inc.     

Sorption and dilation in poly(ethyl methacrylate)–carbon dioxide system

Sorption and dilation in the system poly(ethyl methacrylate) (PEMA) and carbon dioxide are reported for pressures up to 50 atm over the temperature range 15–85°C. The sorption isotherms were obtained gravimetrically. The dilation accompanying sorption was measured directly with a cathetometer. At low temperatures the sorption and dilation isotherms were concave toward the pressure axis in the low-pressure region and turned to convex with increasing pressure. As the experimental temperature approached and exceeded the glass transition temperature of 61°C, both isotherms became convex or linear over the whole range of pressure. Partial molar volumes of CO₂ in PEMA were obtained from sorption and dilation data, which were described well by the extended dual-mode sorption and dilation models developed recently. The temperature dependence of the dual-mode parameters and the isothermal glass transition are discussed.     

Sorption and partial molar volume of gases in poly (dimethyl siloxane)

Sorption of N₂, O₂, Ar, CH₄, CO₂, C₂H₄, and C₂H₆ in poly (dimethyl siloxane) liquid and rubber and the dilation of the polymers due to sorption of the gases are studied at 25°C under pressures up to 50 atm. In the liquid, the sorption isotherms for low-solubility and high-solubility gases are described by Henry's law and the Flory–Huggins equation, respectively. Gas sorption in the rubber, which contains a 29 wt % silica filler, follows the dual-mode sorption model, though marked hysteresis is observed in the sorption of O₂ and CH₄. The dilation isotherms increase linearly or exponentially in both polymers with increasing pressure. Considering that gas molecules adsorbed into micropores of the filler particles do not participate in the dilation, partial molar volumes of the dissolved gases in the rubber are determined from data of sorption and dilation. The values are nearly equal to the partial molar volumes in the liquid (48–60 cm³/mol).     

Effect of penetrant-induced isothermal glass transition on sorption,dilation, and diffusion behavior of polybenzylmethacrylate/CO2

The effect of a penetrant-induced isothermal glass transition on sorption, dilation, and diffusion behavior was studied in a single experimental run for CO₂ in cast polybenzylmethacrylate films. The dual-mode type sorption isotherms below the glass transition temperature of the polymer changed to linear ones above a certain concentration. Meanwhile, partial molar volume of CO₂ determined from the dilation of the films above the concentration gave a value very close to the one reported for rubbery polymers, and diffusion coefficients became less concentration-dependent. The results were conformable to the concept of unrelaxed volume in glassy polymers. © 1996 John Wiley & Sons, Inc.     

Gravimetric study of high-pressure sorption of gases in polymers

A gravimetric method for determining precisely the solubility of gases in polymers at high pressure is described. The solubilities of N₂ and CO₂ in low-density polyethylene (LDPE); CO₂ in polycarbonate (PC); and N₂, CH₄, C₂H₆, and CO₂ in polysulfone (PSUL) have been measured as a function of pressure up to 50 atm. Most of the measured sorption isotherms agreed closely with published data, but reproducible and time-dependent hysteresis in the sorption of CO₂, C₂H₆, and CH₄ in glassy polymers, PC, and PSUL, was observed in this study for the first time. Like the well known conditioning effect of high-pressure CO₂ on the sorption capacity of glassy polymers, these hysteresis phenomena are believed to be due to the plasticizing effect of sorbed gases. On the basis of the current data, the dual-mode sorption model including the plasticization by sorbed gas is discussed and a primitive equation for the concentration of sorbed gases in a quasiequilibrium state of sorption or desorption is proposed.     

Evaluation of gas sorption parameters and prediction of sorption isotherms in glassy polymers

A model of continuous‐site distribution for gas sorption in glassy polymers is examined with sorption data of CO₂ and Ar in polycarbonate. A procedure is presented for determining from a measured isotherm the number of sorption sites in a polymer, an important parameter that previously had to be assumed. With this parameter value and solubility data obtained at zero pressure, the model can reasonably predict sorption isotherms of CO₂ in glassy polycarbonate for a wide temperature range. The number of sorption sites and the average site volume evaluated from CO₂ sorption isotherms are employed for the prediction of Ar sorption isotherms with zero‐pressure solubility data and the independently measured partial molar volume of Ar. A reasonable fit to the measured isotherms of Ar is achieved. With the proposed procedure, the continuous‐site model shows several advantages over the conventional dual‐mode sorption model. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 883–888, 2000     

Gas sorption-induced dilation of poly(4-methyl-1-pentene)

Sorption and volume dilation isotherms of semicrystalline poly(4-methyl-1-pentene) (PMP) were measured using CO₂ and C₃H₈ as penetrants, which have sieving diameters of 3.3 and 4.3 Å, respectively. On the other hand, the PMP crystal has a void width of approximately 4 Å as estimated by X-ray diffraction, so it was anticipated that CO₂ would be able to sorb into the PMP crystal while C₃H₈ would not. The data show that C₃H₈ has a constant partial molar volume of approximately 87 cc/mol, just above the value reported in other rubbery polymers, and are consistent with the hypothesis that the C₃H₈ molecules are too large to sorb into the PMP crystals. The partial molar volume of CO₂ was found to be 39 cc/mol for CO₂ weight fractions of up to 0.03. Since the typical partial molar volume of CO₂ in rubbery materials is 46 cc/mol, the lower values in this study were attributed to CO₂ sorption into crystalline regions of the polymer, which provided no dilation. Application of a two-phase model using the assumption of Henry's law sorption showed that apparently all C₃H₈ sorption was occurring in the amorphous region but approximately 16% of CO₂ sorption occurred in the crystalline regions. © 1996 John Wiley & Sons, Inc.     

Dilation of polycarbonate by carbon dioxide

A new technique is described for dilatometry under high pressure. The technique is based on optical interferometry and is analogous to measuring the thickness of thin, nonabsorbing films and coatings. The procedure is demonstrated for the well-characterized system of n-pentane sorption by polyisobutylene, and then results for the dilation of polycarbonate by the sorption of carbon dioxide are presented. The dilation of polycarbonate by CO₂ is nearly linear with concentration; the partial molar volume of CO₂ decreases slightly with increasing pressure. This result indicates that all sorbed CO₂ molecules contribute equally to the dilation of the polymer matrix and that none reside in microvoids or in preexisting free-volume elements which do not contribute to volume expansion of the polymer.     

Argon sorption and partial molar volume in poly(ethyl methacrylate) above and below the glass transition temperature

Sorption and dilation isotherms for argon in poly(ethyl methacrylate) (PEMA) are reported for pressures up to 50 atm over the temperature range 5–85°C. At temperatures below the glass transition (T_g=61°C), sorption isotherms are well described by the dual-mode sorption model; and isotherms above T_g follow Henry's law. However, isotherms for dilation due to sorption are linear in pressure at all temperatures over the range investigated. Partial molar volumes of Ar in PEMA are obtained from these isotherms. The volumes are approximately constant above T_g (about 40 cm³/mol), whereas the volumes below T_g are smaller and dependent on both temperature and concentration (19–26 cm³/mol). By analyzing the experimental data according to the dual-mode sorption and dilation model, the volume occupied by a dissolved Ar molecule and the mean size of microvoid in the glass are estimated to be 67 129 ų, respectively. The cohesive energy density of the polymer is also estimated as 61 cal/cm³ from the temperature dependence of the dual-mode parameters.     

Gas sorption in poly(vinyl benzoate)

High-pressure sorption (up to 50 atm) for CO₂, N₂, and Ar in poly(vinyl benzoate) (PVB) was studied at temperatures from 25 to 70°C by a gravimetric method utilizing an electromicrobalance. The results are described by Henry's law above the glass transition temperature T_g for all gases. The dual-mode sorption model, Henry's law plus a Langmuir isotherm, applies to the sorption isotherms of N₂ and Ar in the glassy state, and the dual-mode parameters are given. For CO₂, a new type of sorption isotherm is observed below T_g. The isotherm is concave to the pressure axis in the low-pressure region and turns into a straight line with increasing CO₂ pressure which can be extrapolated back to the coordinate origin. The linear part of the isotherm is characteristic of the rubbery state, while the nonlinear part stems from glassystate behavior. The “glass transition solubility” of CO₂, at which PVB film changes from the glassy to the rubbery state, decrease as the temperature increases. The disappearance of microvoids, that is, the decrease of the Langmuir capacity, may be due to a large plasticizing effect of sorbed CO₂. The difference between the N₂ and Ar isotherms and the CO₂ isotherm is discussed from this standpoint.     

Swelling and sorption in polymer–CO2 mixtures at elevated pressures

Experimental data on gas sorption and polymer swelling in glassy polymer—gas systems at elevated pressures are presented for CO₂ with polycarbonate, poly(methyl methacrylate), and polystyrene over a range of temperatures from 33 to 65°C and pressures up to 100 atm. The swelling and sorption behavior were found to depend on the occurrence of a glass transition for the polymer induced by the sorption of CO₂. Two distinct types of swelling and sorption isotherms were measured. One isotherm is characterized by swelling and sorption that reach limiting values at elevated pressures. The other isotherm is characterized by swelling and sorption that continue to increase with pressure and a pressure effect on swelling that is somewhat greater than the effect of pressure on sorption. Glass transition pressures estimated from the experimental results for polystyrene with CO₂ are used to obtain the relationship between CO₂ solubility and the glass transition temperature for the polymer. This relationship is in very good agreement with a theoretical corresponding-states correlation for glass transition temperatures of polystyrene-liquid diluent mixtures.     

CO2 sorption in wet ordered mesoporous silica kit-6: effects of water content and mechanism on enhanced sorption capacity

The sorption isotherms of CO₂ in wet ordered mesoporous silica KIT-6 with different amounts of pre-adsorbed water were firstly collected experimentally using a volumetric method in the temperature range of 275–281 K. The isotherms show an inflection point indicating CO₂ hydrates form in the pore spaces which is proofed by the enthalpy change calculated at the inflection pressure, and the quantity of water content shows considerable effect on the sorption capacity of CO₂. The highest enhancement of sorption capacity in the presence of water is observed in wet KIT-6 sample with water loadings of 2.48, which is about 12.80 mmol/g and 1.86 times than that on dry sample. However, the saturation capacity is still far less than that what can be stored merely in the form of hydrates due to the low ratio of water utilization because of the large pore and the polar surface of KIT-6.     

Sorption and diffusion of gases in a polyimide

Sorption and diffusion of gases (CO₂, N₂, and He) in a polyimide (PI2080) film were measured by using an apparatus which gives the sorption rate curves from the initial state to the equilibrium state. Nonlinear isotherms observed for CO₂ sorption were interpreted successfully in terms of the dual-mode model for sorption in glassy polymers. Linear isotherms observed for N₂ and He seemed to obey Henry's law. Two diffusion coefficients (D_I and D_E) were obtained using the short-time method and the long-time method for a Fickian diffusion model, together with the equilibrium solubility (C_e) from each experiment. The initial sorption rate curves agreed with the calculated curves using D_I, however near sorption equilibrium the curves are in accord with the calculated curves using D_E. These observations suggest that some relaxation process is superimposed on the diffusion process. The non-Fickian transport data were correlated successfully with a model that combines time-dependent diffusion and the Fickian model.     

Comparison of three models for permeation of CO2/CH4 mixtures in poly(phenylene oxide)

Two models for the permeability of pure gases have been extended to include binary gas mixtures. The first is an extension of a pure gas permeability model, proposed by Petropoulos, which is based on gradients of chemical potential. This model predicts the permeability of components in a gas mixture solely on the basis of competition for sorption sites within the polymer matrix. The second mixed gas model follows an earlier analysis by Barrer for pure gases which includes the effects of saturation of Langmuir sites on the diffusion as well as the sorption processes responsible for permeation. This generalized “competitive sorption/diffusion” model includes the effect of each gas component on the sorption and diffusion of the other component in the mixture. The flux equations from these two models have been solved numerically to predict the permeability of gas mixtures on the basis of pure gas sorption and transport parameters. Both the mixed gas Petropoulos and competitive sorption/diffusion model predictions are compared with predictions from the earlier simple competitive sorption model based on gradients of concentration. An analysis of all three models is presented for the case of CO₂/CH₄ permeability in poly(phenylene oxide) (PPO). As expected, the competitive sorption/diffusion model predicts lower permeability than either of the models which consider only competitive sorption effects. The permeability depression of both CO₂ and CH₄ predicted by the competitive sorption/diffusion model is roughly twice that predicted by the competitive sorption model, whereas the mixed gas Petropoulos model predictions for both gases lie between the other two model predictions. For the PPO/CO₂/CH₄ system, the methane permeability data lie above the predictions of all three models, whereas CO₂ data lie below the predictions of all models. Consequently, the competitive sorption/diffusion model gives the most accurate prediction for CO₂, while the simple competitive sorption model is best for methane. The effects of mixed gas sorption, fugacity, and CO₂-induced dilation were considered and do not explain the inaccuracies of any of the models. The relatively small errors in mixed gas permeability predictions using either of the three models are likely to be related to “transport plasticization” of PPO owing to high levels of CO₂ sorption and its effect on polymer segmental motions and gas diffusivity.     

Competitive permeation of gas and water vapour in high free volume polymeric membranes

Highly permeable glassy polymeric membranes based on poly (1‐trimethylsilyl‐1‐propyne) (PTMSP) and a polymer of intrinsic porosity (PIM‐1) were investigated for water sorption, water permeability and the separation of CO₂ from N₂ under humid mixed gas conditions. The water sorption isotherms for both materials followed behavior indicative of multilayer adsorption within the microvoids, with PIM‐1 registering a significant water uptake at very high water activities. Analysis of the sorption isotherms using a modified dual sorption model which accounts for such multilayer effects gave Langmuir affinity constants more consistent with lighter gases than the use of the standard dual mode approach. The water permeability through PTMSP and PIM‐1 was comparable over the water activities studied, and could be successfully model ed through a dual mode sorption model with a concentration dependent diffusivity. The water permeability through both membranes as a function of temperature was also measured, and found to be at a minimum at 80 ° C for PTMSP and 70 °C for PIM‐1. This temperature dependence is a function of reducing water solubility in both membranes with increasing temperature countered by increasing water diffusivity. The CO₂ ‐ N₂ mixed gas permeabilities through PTMSP and PIM‐1 were also measured and model ed through dual mode sorption theory. Introducing water vapour further reduced both the CO₂ and N₂ permeabilities. The plasticization potential of water in PTMSP was determined and indicated water swelled the membrane increasing CO₂ and N₂ diffusivity, while for PIM‐1 a negative potential implied that water filling of the microvoids hampered CO₂ and N₂ diffusion through the membrane. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 719–728     

Sorption and diffusion of carbon dioxide in single-phase polystyrene/poly(vinylmethylether) blends

The sorption and transport properties of CO₂ in miscible PS/PVME blends at 20°C are reported as a function of pressure from 1 to 15 atm. The complex shape of isotherms for glassy blends and the concentration-dependent diffusion coefficient for rubbery blends reveal a plasticization by sorbed CO₂. The significant depression in T_g has to be taken into account in the analysis of the sorption data. Diffusion coefficient for CO₂ passes through a minimum when plotted against the blend composition. Such a behavior can be quantitatively related to the negative volume mixing of the PS/PVME system in the framework of the theories based on unoccupied volume. © 1996 John Wiley & Sons, Inc.     

Sorption of CO2 in polymers observed by positron annihilation technique

Positron annihilation lifetimes were measured for several polymers in the atmosphere of high pressure CO₂ gas. At low CO₂ pressured both ₃ andI ₃ decreased due to the Langmuir-type sorption, and at higher pressures their values recovered because the Henry-type sorption takes over. The amount of sorbed CO₂ and dilation of the bulk volume were measured simultaneously, and the free volume fraction was determined at each CO₂ pressure. The free volume fraction became smaller (for polyimide and polycarbonate) or slightly larger (for polyethylene) with the progress of sorption. However, the size of the o-Ps hole estimated from the ₃ value increased regardless of the change of the free volume fraction. It appears that o-Ps is selectively looking at larger holes or expanding the holes in which it is accommodated. For polycarbonate, which remains to be glassy even at the largest CO₂ sorption attained in the experiment, the o-Ps hole size became larger than that before sorption. This implies that, even if the polymer is glassy as bulk, the sorption site is strongly prone to molecular displacement by the pressure of the penetrating Ps. Cautious consideration is evoked about directly correlating the o-Ps lifetime and intensity with the free volume in general.