Effect of associating polymer on the viscosity behavior of suspensions consisting of particles with different surface properties

Associating polymers which consist of water-soluble long-chain molecules containing a small fraction of hydrophobic groups (hydrophobes) behave as flocculants in aqueous suspensions. The effects of associating polymers on the rheological behavior are studied for single suspensions of particles with hydrophilic and hydrophobic surfaces, and their mixtures. For particles with hydrophilic surfaces, the suspensions are highly flocculated by a bridging mechanism, because the water-soluble chains adsorb onto hydrophilic surfaces. On the other hand, the particles with hydrophobic surfaces cannot be dispersed in water without polymer and the additions of a small amount of polymer are required for preparation of homogeneous suspensions. The associating polymer acts as a dispersant at low concentrations. However, further additions of polymer lead to a drastic increase in viscosity. Since the hydrophobes on one end of molecules adsorb onto hydrophobic surfaces and other hydrophobes tending from the particles can form micelles, the particles are connected by linkage of interchain associations. By mixing two suspensions of particles with hydrophilic and hydrophobic surfaces, the viscosity is substantially reduced and the flow becomes nearly Newtonian. The associating polymer in complex suspensions acts as a binder between the hydrophilic and hydrophobic surfaces. The hetero-flocculation which leads to the formation of composite particles may be responsible for the viscosity reduction of complex suspensions.     

特殊浸润性表面的液滴凝结

以铝片为基底, 经电化学腐蚀和沸水处理制备了多级微纳米结构; 通过气相沉积和涂油分别制备了超疏水表面、 疏水超润滑(slippery)表面和亲水slippery表面; 探究了表面不同的特殊浸润性(超亲水、 超疏水、 疏水slippery和亲水slippery)对液滴凝结的影响. 结果表明, 超亲水表面的液滴凝结属于膜状冷凝, 超疏水表面和slippery表面的液滴凝结均属于滴状冷凝. 超疏水表面液滴合并时, 合并的液滴会不定向弹离表面. 疏水slippery表面和亲水slippery表面由于表面浸润性的不同导致液滴成核密度和液滴合并的差异, 亲水slippery表面凝结液滴的最大体积远大于疏水slippery表面凝结液滴的最大体积. 4种表面的雾气收集效率由大到小依次为亲水slippery表面>疏水slippery表面>超亲水表面>超疏水表面.     

Adsorption of the fusogenic peptide B18 onto solid surfaces: insights into the mechanism of peptide assembly

The adsorption and assembly of B18 peptide on various solid surfaces were studied by reflectometry techniques and atomic force microscopy. B18 is the minimal membrane binding and fusogenic motif of the sea urchin protein bindin, which mediates the fertilization process. Silicon substrates were modified to obtain hydrophilic charged surfaces (oxide layer and polyelectrolyte multilayers) and hydrophobic surfaces (octadecyltrichlorosilane). B18 does not adsorb on hydrophilic positively charged surfaces, which was attributed to electrostatic repulsion since the peptide is positively charged. In contrast, the peptide irreversibly adsorbs on negatively charged hydrophilic as well as on hydrophobic surfaces. B18 showed higher affinity for hydrophobic surfaces than for hydrophilic negatively charged surfaces, which must be due to the presence of hydrophobic side chains at both ends of the molecule. Atomic force microscopy provided the indication that lateral diffusion on the surface affects the adsorption process of B18 on hydrophobic surfaces. The adsorption of the peptide on negatively charged surfaces was characterized by the formation of globular clusters.     

Adsorption states of amphipatic solutes at the surface of naturally hydrophobic minerals: a molecular dynamics simulation study

An initial molecular dynamics simulation study regarding interfacial phenomena at selected naturally hydrophobic surfaces is reported. Simulation results show that, due to the natural hydrophobicity of graphite and talc basal planes, the cationic surfactant dodecyltrimethylammonium bromide preferentially adsorbs at these surfaces through hydrophobic interactions. When a model dextrin molecule is considered, the simulation results suggest that the hydrophobic interaction between the naturally hydrophobic surfaces of graphite, talc basal plane, and sulfur and the hydrophobic moieties (C-H and methylene groups) in the dextrin molecule plays a significant role in dextrin adsorption at these surfaces. The hydroxyl group in the dextrin molecule also contributes to its adsorption at the talc basal plane surface. In contrast, dextrin was not found to adsorb at talc edge surfaces.     

Residence time dependent desorption of Staphylococcus epidermidis from hydrophobic and hydrophilic substrata

Adhesion and desorption are simultaneous events during bacterial adhesion to surfaces, although desorption is far less studied than adhesion. Here, desorption of Staphylococcus epidermidis from substratum surfaces is demonstrated to be residence time dependent. Initial desorption rate coefficients were similar for hydrophilic and hydrophobic dimethyldichlorosilane (DDS)-coated glass, likely because initial desorption is controlled by attractive Lifshitz–Van der Waals interactions, which are comparable on both substratum surfaces. However, significantly slower decay times of the desorption rate coefficients are found for hydrophilic glass than for hydrophobic DDS-coated glass. This difference is suggested to be due to the acid–base interactions between staphylococci and these surfaces, which are repulsive on hydrophilic glass and attractive on hydrophobic DDS-coated glass. Final desorption rate coefficients are higher on hydrophilic glass than on hydrophobic DDS-coated glass, due to the so called hydrophobic effect, facilitating a closer contact on hydrophobic DDS-coated glass.     

Molecular packing of lysozyme,fibrinogen, and bovine serum albumin on hydrophilic and hydrophobic surfaces studied by infrared-visible sum frequency generation and fluorescence microscopy

Infrared-visible sum frequency generation (SFG) vibrational spectroscopy, in combination with fluorescence microscopy, was employed to investigate the surface structure of lysozyme, fibrinogen, and bovine serum albumin (BSA) adsorbed on hydrophilic silica and hydrophobic polystyrene as a function of protein concentration. Fluorescence microscopy shows that the relative amounts of protein adsorbed on hydrophilic and hydrophobic surfaces increase in proportion with the concentration of protein solutions. For a given bulk protein concentration, a larger amount of protein is adsorbed on hydrophobic polystyrene surfaces compared to hydrophilic silica surfaces. While lysozyme molecules adsorbed on silica surfaces yield relatively similar SFG spectra, regardless of the surface concentration, SFG spectra of fibrinogen and BSA adsorbed on silica surfaces exhibit concentration-dependent signal intensities and peak shapes. Quantitative SFG data analysis reveals that methyl groups in lysozyme adsorbed on hydrophilic surfaces show a concentration-independent orientation. However, methyl groups in BSA and fibrinogen become less tilted with respect to the surface normal with increasing protein concentration at the surface. On hydrophobic polystyrene surfaces, all proteins yield similar SFG spectra, which are different from those on hydrophilic surfaces. Although more protein molecules are present on hydrophobic surfaces, lower SFG signal intensity is observed, indicating that methyl groups in adsorbed proteins are more randomly oriented as compared to those on hydrophilic surfaces. SFG data also shows that the orientation and ordering of phenyl rings in the polystyrene surface is affected by protein adsorption, depending on the amount and type of proteins.     

The hydrophobic effect: molecular dynamics simulations of water confined between extended hydrophobic and hydrophilic surfaces

Structural and dynamic properties of water confined between two parallel, extended, either hydrophobic or hydrophilic crystalline surfaces of n-alkane C(36)H(74) or n-alcohol C(35)H(71)OH, are studied by molecular dynamics simulations. Electron density profiles, directly compared with corresponding experimental data from x-ray reflectivity measurements, reveal a uniform weak de-wetting characteristic for the extended hydrophobic surface, while the hydrophilic surface is weakly wetted. These microscopic data are consistent with macroscopic contact angle measurements. Specific water orientation is present at both surfaces. The ordering is characteristically different between the surfaces and of longer range at the hydrophilic surface. Furthermore, the dynamic properties of water are different at the two surfaces and different from the bulk behavior. In particular, at the hydrophobic surface, time-correlation functions reveal that water molecules have characteristic diffusive behavior and orientational ordering due to the lack of hydrogen bonding interactions with the surface. These observations suggest that the altered dynamical properties of water in contact with extended hydrophobic surfaces together with a partial drying of the surfaces are more indicative of the hydrophobic effect than structural ordering, which we suggest to be independent of surface topology.     

Assembly of nanoparticles at the contact line of a drying droplet under the influence of a dipped tip

The manipulation of colloidal nanoparticles (NPs) in a drying droplet has critical importance not only for several industrial applications but also their assembly into patterns on surfaces. The influence of a tip with hydrophilic or hydrophobic surfaces dipped into a drying droplet on hydrophilic or hydrophobic surfaces on the behavior of 98 nm latex NPs was investigated. The formation of concentric rings on hydrophilic glass surfaces regardless of the surface chemistry of the dipped tip was observed. On the other hand, no pattern formation on hydrophobic surfaces was observed with the insertion of the tip. With a hydrophilic tip, the concentric rings were formed due to stick-slip motion of the solvent contact line resulting from competition between pinning and capillary forces while the capillary effect was not effective until the surface of the tip was changed by adherent NPs making the tip surface available for water adherence with a hydrophobic tip, which results in the pulling of droplet towards the tip. It is also found that the tip thickness and suspension concentration significantly influences the formation of concentric rings on surfaces. This simple procedure can be used to influence the distribution or assembly of NPs in the droplet area.     

Direct measurement of hydrophobic forces on cell surfaces using AFM

Although hydrophobic forces are of great relevance in biological systems, quantifying these forces on complex biosurfaces such as cell surfaces has been difficult owing to the lack of appropriate, ultrasensitive force probes. Here, chemical force microscopy (CFM) with hydrophobic tips was used to measure local hydrophobic forces on organic surfaces and on live bacteria. On organic surfaces, we found an excellent correlation between nanoscale CFM and macroscale wettability measurements, demonstrating the sensitivity of the method toward hydrophobicity and providing novel insight into the nature of hydrophobic forces. Then, we measured hydrophobic forces associated with mycolic acids on the surface of mycobacteria, supporting the notion that these hydrophobic compounds represent an important permeation barrier to drugs.     

On the stability of the polymer brushes formed by adsorption of ionomer complexes on hydrophilic and hydrophobic surfaces

We have studied the effect of normal forces and shear forces on the stability and functionality of a polymer brush layer formed upon adsorption of polymeric micelles on hydrophilic and hydrophobic surfaces. The micelles consist of oppositely charged polyelectrolyte blocks (poly(acrylic acid) and poly(N-methyl 2-vinyl pyridinium iodide), and a neutral block (poly(vinyl alcohol)) or neutral grafts (poly(ethylene oxide)). The strength of the attachment of the micellar layers to various substrates was evaluated with Atomic Force Microscopy. Flow cell experiments allowed for the evaluation of long-term stability of coatings in lateral flow. Fixed angle optical reflectometry was used to quantify protein (BSA) adsorption on the micellar layers after their exposure to flow. The results show that adsorbed micellar layers are relatively weakly attached to hydrophobic surfaces and much stronger to hydrophilic surfaces, which has a significant impact on their stability. Adsorbed layers maintain their ability to suppress protein adsorption on hydrophilic surfaces but not on hydrophobic surfaces. Due to the relatively weak attachment to hydrophobic surfaces the structure of adsorbed layers may easily be disrupted by lateral forces, such that the complex coacervate-brush structure no longer exists.     

Molecular modeling of interactions between L-lysine and functionalized quartz surfaces

Molecular modeling techniques have been used to investigate the interaction of L-lysine in aqueous medium with silanol and methyl sites onto quartz substrates. The substrate effect has been studied for partially hydrophilic surfaces formed by silanol and methyl groups with a ratio of 1:5 and hydrophobic fully methylated surfaces. Molecular dynamics and static calculations indicate that L-lysine does not show any significant interaction with fully methylated surfaces, while its interaction with hydroxylated/methylated surfaces is dominated by electrostatic and H-bond terms. Accordingly, on fully methylated surfaces there is no preferential orientation of L-lysine with respect to the surface, while for hydroxylated/methylated surfaces the L-lysine-surface interaction mainly depends on the molecular orientation, with a preferred geometry involving the ammonium group pointing toward the silanol site. The structure of water shells around L-lysine molecules was shown to be strongly affected by the relative hydrophilic/hydrophobic character of the surfaces. In particular, the order is almost completely lost for partially hydrophilic surfaces, while well-defined hydration shells around L-lysine are obtained for hydrophobic surfaces.     

Molecular hydrophobic attraction and ion-specific effects studied by molecular dynamics

Much is written about "hydrophobic forces" that act between solvated molecules and nonpolar interfaces, but it is not always clear what causes these forces and whether they should be labeled as hydrophobic. Hydrophobic effects roughly fall in two classes, those that are influenced by the addition of salt and those that are not. Bubble adsorption and cavitation effects plague experiments and simulations of interacting extended hydrophobic surfaces and lead to a strong, almost irreversible attraction that has little or no dependence on salt type and concentration. In this paper, we are concerned with hydrophobic interactions between single molecules and extended surfaces and try to elucidate the relation to electrostatic and ion-specific effects. For these nanoscopic hydrophobic forces, bubbles and cavitation effects play only a minor role and even if present cause no equilibration problems. In specific, we study the forced desorption of peptides from nonpolar interfaces by means of molecular dynamics simulations and determine the adsorption potential of mean force. The simulation results for peptides compare well with corresponding AFM experiments. An analysis of the various contributions to the total peptide-surface interactions shows that structural effects of water as well as van der Waals interactions between surface and peptide are important. Hofmeister ion effects are studied by separately determining the effective interaction of various ions with hydrophobic surfaces. An extension of the Poisson-Boltzmann equation that includes the ion-specific potential of mean force yields surface potentials, interfacial tensions, and effective interactions between hydrophobic surfaces. There, we also analyze the energetic contributions to the potential of mean force and find that the most important factor determining ion-specific adsorption at hydrophobic surfaces can best be described as surface-modified ion hydration.     

Stability of monomolecular films of archaebacterial tetraether lipids on silicon wafers: a comparison of physisorbed and chemisorbed monolayers

The monomolecular organisation of symmetric, chemically modified tetraether lipids caldarchaeol-PO(4) was studied using Langmuir film balance, ellipsometry, and atomic force microscopy (AFM). Solid silicon wafer substrates were modified to hydrophobic, hydrophilic, and amino-silanised surfaces; and Langmuir-Blodgett (LB)-films were transferred onto each. LB-caldarchaeol-PO(4) films were subjected to further rinsing with organic solvent and additional physical treatments, to compare their resistance and stability on chemisorbed (amino-silanised) and physisorbed (hydrophobic and hydrophilic) surfaces. The resistance and stability of these monolayer films was characterized by ellipsometry and AFM, and film thickness was determined using ellipsometry. AFM was also employed to observe surface morphology. Monolayer films on hydrophobic surfaces were found to be more resistant to rinsing with organic solvent and additional physical treatments than monolayer films on either amino-silanised or hydrophilic surfaces. The hydrophobic effect with hydrophobic surfaces appears to support the formation of stronger caldarchaeol-PO(4) films on silicon wafer substrates, with increased resistance and stability.     

Surface thermodynamics of osteoblasts: relation between hydrophobicity and bone active biomaterials

Surface tensions of rat calvaria osteoblasts were determined by measuring the cell–liquid–vapor contact angle with sessile drops of water on the cell monolayer. The results indicated the hydrophobic character of osteoblastic cells with a contact angle of 26.89° (0.29°). This value could explain the ability of osteoblasts to specifically attach onto hydrophobic surfaces like titanium or hydroxyapatite. The first cellular step of bone healing requires the presence of osteoblasts and their adhesion to biomaterial surfaces is the crucial phase of the osteointegration process. The presence of a monolayer of a newly discovered hydrophobic bacterial exopolysaccharide on coverglass slides appeared to strongly encourage adhesion of osteoblastic cells. In that, providing surfaces with this hydrophobic material induced a selective adsorption of osteoblast cells and might enhance osteointegration.     

Controlling chemical reactivity at solid-solution interfaces by means of hydrophobic magnetic nanoparticles

Hydrophobic magnetic nanoparticles are employed to reversibly regulate the hydrophobic/hydrophilic properties of surfaces and to control the electrochemistry and bioelectochemistry at chemically modified electrodes. Selective bioelectrocatalytic transformations at relay-functionalized electrodes are accomplished by the magnetic attractions of the hydrophobic magnetic nanoparticles with coadsorbed hydrophobic redox relays to the electrode. The selective activation of one of two biocatalysts solubilized in the aqueous electrolyte solution in the absence or presence of hydrophobic magnetic nanoparticles results in the specific activation of bioelectrocatalytic processes. The magnetic attraction and retraction of hydrophobic magnetic nanoparticles to and from semiconductor nanoparticle (CdS)-functionalized electrodes enable the control of the photocurrent directions at the electrode from cathodic to anodic directions, respectively. The magnetic attraction of the hydrophobic magnetic nanoparticles to the surfaces is also employed to control biorecognition and biocatalytic transformations at solid supports. The magnetic attraction and retraction of the hydrophobic magnetic nanoparticles to and from the surfaces allow the blockage and activation of DNA hybridization, polymerization, and enzymatic digestion, respectively.     

Induced hydrophobic recovery of oxygen plasma-treated surfaces

Plasma treatment is a widely used method in microfabrication laboratories and the plasticware industry to functionalize surfaces for device bonding and preparation for mammalian cell culture. However, spatial control of plasma treatment is challenging because it typically requires a tedious masking step that is prone to alignment errors. Currently, there are no available methods to actively revert a surface from a treated hydrophilic state to its original hydrophobic state. Here, we describe a method that relies on physical contact treatment (PCT) to actively induce hydrophobic recovery of plasma-treated surfaces. PCT involves applying brushing and peeling processes with common wipers and tapes to reverse the wettability of hydrophilized surfaces while simultaneously preserving hydrophilicity of non-contacted surfaces. We demonstrate that PCT is a user-friendly method that allows 2D and 3D surface patterning of hydrophobic regions, and the protection of hydrophilic surfaces from unwanted PCT-induced recovery. This method will be useful in academic and industrial settings where plasma treatment is frequently used.     

Interfacial water on hydrophobic surfaces recognized by ions and molecules

Recent spectrophotometric and molecular dynamics simulation studies have shown that the physicochemical properties and structures of water in the vicinity of hydrophobic surfaces differ from those of the bulk water. However, the interfacial water acting as a separation medium on hydrophobic surfaces has never been detected and quantified experimentally. In this study, we show that small inorganic ions and organic molecules differentiate the interfacial water formed on the surfaces of octadecyl-bonded (C(18)) silica particles from the bulk water and the chemical separation of these solutes in aqueous media with hydrophobic materials can be interpreted with a consistent mechanism, partition between the bulk water phase and the interfacial water formed on the hydrophobic surface. Thermal transition behaviour of the interfacial water incorporated in the nanopores of the C(18) silica materials and the solubility parameter of the water calculated from the distribution coefficients of organic compounds have indicated that the interfacial water may have a structure of disrupted hydrogen bonding. The thickness of the interfacial water or the limit of distance from the hydrophobic surface at which molecules and ions can sense the surface was estimated to be 1.25 ± 0.13 nm from the volume of the interfacial water obtained by a liquid chromatographic method and the surface area, suggesting that the hydrophobic effect may extend beyond the first solvation shell of water molecules directly surrounding the surfaces.     

The inevitable accumulation of large ions and neutral molecules near hydrophobic surfaces and small ions near hydrophilic ones

The present contribution offers a unified explanation to three central phenomena in physical chemistry of interfaces in contact with aqueous solution: (1) Accumulation of large anions at the air/water interface. (2) Accumulation of neutral gas molecules near hydrophobic surfaces and the resulting hydrophobic interaction between two such surfaces, and (3) The Hofmeister effect, namely, the enhanced propensity of small ions to hydrophilic surfaces and large ions to hydrophobic surfaces. The common thread linking these phenomena is the free energy balance between ion or molecule hydration in solution and the cost of localizing these objects at the water-surface interface. Comparing the results of an abstract lattice-gas model to force spectroscopy data collected by AFM we reveal the underlying principles and demonstrate their universality.     

Long-range attraction between surfaces: existence and amplitude?

The possible occurrence of a long-range attraction between hydrophobic surfaces is fundamental for understanding the kinetics of protein folding or self-assembling structures, such as biological membranes, the stability of emulsions and inorganic dispersions. Direct force measurements have revealed the presence in water of a long-range attraction between macroscopic and hydrophobic surfaces. Nevertheless, the existence of this so-called ‘hydrophobic force’ for smaller objects is still under discussion. For macroscopic surfaces, it appears that electrostatic contributions due to surface heterogeneities and gas effects and/or bubble bridging have to be taken into account, but do they define an intrinsic ‘hydrophobic force’? For charged colloidal particles, theoretical predictions of electrostatic attraction and a phase separation when the counterions are multivalent, are partially confirmed by experiments, and recent experimental evidences of an attraction in a confined geometry put an exciting challenge for theoreticians.     

Multiscale modeling and simulations of protein adsorption: progresses and perspectives

Protein adsorption, which shows wide prospects in many practical applications such as biosensors, biofuel cells, and biomaterials, has long been identified as a very complex problem in interface science. Here, we present a review on the multiscale modeling and simulation methods of protein adsorption on surfaces with different properties. First, various simulation algorithms (replica exchange, metadynamics, TIGER2A, and PSOVina) and protein models (colloidal, coarse-grained, and all-atom models) are introduced. Then, recent molecular simulation progresses about protein adsorption on different material surfaces (such as charged, hydrophobic, hydrophilic, and responsive surfaces) are retrospected. It has been demonstrated that the adsorption orientation of proteins on charged surfaces and hydrophobic surfaces can be controlled by the electrical dipole and the hydrophobic dipole of proteins, respectively. Superhydrophilic zwitterionic surfaces can resist protein adsorption because of the strong hydration. Under the stimuli of external conditions, the surface properties of materials can be modulated, and thus, the adsorption/desorption of proteins on responsive surfaces can be controlled. Finally, the future directions of molecular simulation study of protein adsorption are discussed.