以固体超强酸SO4^2-／ZrO2-Fe2O3催化合成醋酸异戊酯

以合成醋酸异戊酯为探针反应,筛选出制备固体超强酸SO2-4 /ZrO2- Fe2O3 (SZF -1 )的最佳工艺条件为:ZrOCl2·8H2O9. 7g, FeCl3·6H2O16. 2g, 常温陈化24h, 0. 5mol·L-1 H2SO4 (15mL·g-1 )浸泡5h, 550℃焙烧3h。以SZF 1为催化剂合成醋酸异戊酯的反应条件为:异戊醇200mmol, n(异戊醇)∶n(醋酸) =1. 0∶1. 3, SZF -1 1g(反应物总质量的3% ), 环己烷15mL, 回流反应3h, 酯化率93. 47%。催化剂连续使用6次后酯化率仍在70%以上。     

SnCl4·5H2 O/C催化合成谷氨酸月桂酯

以谷氨酸和月桂醇为原料,固体酸SnCl4·H2O/C为催化剂合成了谷氨酸月桂酯.正交实验得出最佳的反应条件为月桂醇100 mmol, n(谷氨酸) ∶ n(月桂醇)＝1 ∶ 1, SnCl4·H2O/C 1.2 g, 135 ℃反应4.0 h,醇转化率97.9%.     

环境友好催化剂TiSiW12O40/TiO2的制备及其催化性能研究

制备了新型固载杂多酸盐TiSiW12O40/TiO2环境友好催化剂,并以丁酸丁酯的合成作为探针反应,系统考察了原料H4SiW12O40@xH2O与TiO2摩尔比、焙烧温度、焙烧时间等制备条件对TiSiW12O40/TiO2催化活性的影响.实验表明:制备催化剂的适宜条件为原料H4SiW12O40@xH2O与TiO2摩尔比为0.47,焙烧温度为350℃,焙烧时间为3.0 h.利用该条件下制备的催化剂TiSiW12O40/TiO2合成丁酸丁酯,正丁醇与正丁酸的投料摩尔比n(醇):n(酸)=1.3:1,催化剂的用量占反应物总投料质量的1.3%,反应时间为1 h,丁酸丁酯的产率为97.2%.该催化剂TiSiW12O40/TiO2用于制备其它丁酸酯类(如乙酯、丙酯、戊酯、异戊酯)时同样取得了好的结果.     

环境友好催化剂TiSiW_(12)O_(40j)/TiO_2的制备及其催化性能研究

制备了新型固载杂多酸盐TiSiW_(12)O_(40)/TiO_2环境友好催化剂，并以丁酸 丁酯的合成作为探针反应，系统考察了原料H_4SiW_(12)O_(40)·xH_2O与TiO_2摩 尔比、焙烧温度、焙烧时间等制备条件对TiSiW_(12)O_(40)/TiO_2催化活性的影响 。实验表明：制备催化剂的适宜条件为原料H_4SiW_(12)O_(40)·xH_2O与TiO_2摩 尔比为0.47，焙烧温度为350 ℃，焙烧时间为3.0 h。利用该条件下制备的催化剂 TiSiW_(12)O_(40)/TiO_2合成了丁酸丁酯正丁醇与正丁醇的投料摩尔比n(醇):n(酸 ) = 1.3:1，催化剂的用量占反应物总投料质量的1.3%，反应时间为1 h，丁酸丁酯 的产率为97.2%。该催化剂TiSiW_(12)O_(40)/TiO_2用于制备其它丁酸酯类（如乙 酯、丙酯、戊酯、异戊酯）时同样取得了好的结果。     

强酸性阳离子交换树脂催化合成马来酸二异戊酯

以强酸性阳离子交换树脂为催化剂催化异戊醇与马来酸酐反应合成了马来酸二异戊酯。在马来酸酐50mmol，异戊醇200mmol和强酸性阳离子交换树脂4.0g，回流分水60min的条件下，马来酸二异戊酯收率达92.2%，树脂重复使用5次，其活性未发生明显的变化。     

以固体超强酸SO2-4/ZrO2-Fe2O3催化合成醋酸异戊酯

以合成醋酸异戊酯为探针反应,筛选出制备固体超强酸SO2-4/ZrO2-Fe2O3(SZF-1)的最佳工艺条件为ZrOCl2·8H2O 9.7 g, FeCl3·6H2O 16.2 g, 常温陈化24 h, 0.5 mol·L-1 H2SO4(15 mL·g-1)浸泡5 h, 550 ℃焙烧3 h.以SZF-1为催化剂合成醋酸异戊酯的反应条件为异戊醇200 mmol, n(异戊醇)n(醋酸)＝1.0 1.3, SZF-1 1 g(反应物总质量的3%), 环己烷15 mL, 回流反应3 h, 酯化率93.47%.催化剂连续使用6次后酯化率仍在70%以上.     

甲烷磺酸铜的合成及在催化酯化反应中的性能研究

合成了甲烷磺酸铜 ,其结构经热重分析和IR表征。研究了以其催化乙酸与异戊醇酯化反应的性能及各种因素对酯化率的影响。反应条件为 :乙酸 1 67mmol,n(乙酸 )∶n(异戊醇 ) =1 .0∶1 .1 ,催化剂用量 0 .2 5 % (以酸的摩尔数计 ) ,回流反应 2 .0h ,不加带水剂 ,酯化率可达 96.0 %。其催化活性远远高于CuSO4·5H2 O ,CuCl2 ·2H2 O ,Cu(NO3 ) 2 ·3H2 O ,Cu(CH3 CO2 ) 2 ·H2 O及其它Lewis酸催化剂 ,而且反应过程中不水解 ,反应后经过简单的相分离即可重复使用 ,并成功地用于催化合成其它酯。     

ZrO_2-TiO_2/SO_4~(2-)催化合成马来酸二异戊酯

以马来酸酐和异戊醇为原料,复合型固体超强酸ZrO2-TiO2/SO24-为催化剂催化合成了马来酸二异戊酯。最佳工艺条件为:催化剂活化温度450℃,活化时间5 h,1.0 mol.L-1H2SO4,催化剂用量1.0 g,酸醇摩尔比为1∶4,回流分水70 m in,酯化率达98.72%。ZrO2-TiO2/SO42-具有良好的催化活性,可重复使用5次以上。     

NaHSO4·H2O催化合成苯甲酸甲酯

以 Na HSO4 · H2 O催化苯甲酸与甲醇的酯化反应 ,合成了苯甲酸甲酯。研究结果表明 ,Na HSO4 · H2 O具有较高的催化活性。考察了苯甲酸 /甲醇摩尔比、催化剂用量及反应时间对酯产率的影响。在优化反应条件 [n(苯甲酸 )∶n(甲醇 )∶n( Na HSO4 ·H2 O) =1∶ 2∶ 0 .2 9,回流8h]下 ,苯甲酸甲酯产率达 85.3 %。     

氨基磺酸催化合成氯乙酸正丁酯

氨基磺酸能够代替硫酸作为酯化催化剂。研究了以氨基磺酸为催化剂,氯乙酸与正丁醇合成氯乙酸正丁酯。研究了反应的影响因素和催化剂的重复使用性能。当氯乙酸、正丁醇和氨基磺酸的摩尔比为0.05:0.15:0.00773,回流分水90min时,酯收率达82.4%。并以氨基磺酸为催化剂合成了氯乙酸异丁酯、氯乙酸仲丁酯、氯乙酸正戊酯、氯乙酸异戊酯和氯乙酸2-戊酯。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.