Equilibrium anionic polymerization of β-methoxypropionaldehyde

Anionic polymerization of β-methoxypropionaldehyde (MPA) was carried out in tetrahydrofuran (THF) by using benzophenone–monolithium complex as an initiator. An equilibrium between polymerization and depolymerization was observed at a temperature range of ?90 to ?70°C. From the temperature dependence of the equilibrium monomer concentration, thermodynamic parameters for the polymerization of MPA in THF were evaluated as follows: ΔH_ss = ?4.8 ± 0.2 kcal/mole, ΔH_SS = ?22.4 ± 1.3 cal/mole-deg, and (T_c)_ss = ?59°C. The thermodynamic change upon the conversion of liquid monomer to condensed polymer was computed from both the partial mixing energy of MPA with THF and the linear relationship between the equilibrium volume fraction of MPA monomer and that of the resulting polymer: ΔH_1c = ?4.7 ± 0.2 kcal/mole, ΔS_1c = ?19.5 ± 1.3 cal/mole-deg, and (T_c)_1c = ?35°C.     

Equilibrium cyclotrimerization of ether oxygen-substituted aliphatic aldehydes

This article describes the equilibrium cyclotrimerization of β-methoxypropionaldehyde (MPA), 4,7-dioxaoctanal (DOA), and n-octanal (OA) initiated by boron trifluoride etherate in toluene at a temperature range of ?10 to 25°C. The enthalpy and entropy changes corresponding to the conversion of 1 mole of the monomers to 1/3 mole of their cyclic trimers in toluene solution, at the initial monomer concentration of 1 mole/liter, were evaluated as follows: ΔH_ss = ?5.9 ± 0.3 kcal/mole and ΔS_ss = ?19.1 ± 1.3 cal/mole deg for the MPA system; ΔH_ss = ?7.4 ± 0.4 kcal/mole and ΔS_ss = ?24.1 ± 1.7 cal/mole deg for the DOA system; ΔH_ss = ?6.1 ± 0.4 kcal/mole and ΔS_ss = ?21.2 ± 1.5 cal/mole deg for the OA system. The comparison of these values with those in their polymerization indicates that the cyclotrimerization of aldehydes is thermodynamically of greater advantage than their polymerization. The effects of long and polar substituents are discussed from the view-point of the intermolecular interactions by the polar groups in monomers and their cyclic trimers.     

Equilibrium anionic polymerization of β-methoxycarbonylpropionaldehyde

β-Methoxycarbonylpropionaldehyde (MCPA) was polymerized in tetrahydrofuran (THF) with benzophenone–monolithium complex as the initiator. An equilibrium between the monomer and its polymer was observed in the temperature range of ?96 to ?78°C. MCPA had lower polymerizability than ether-substituted aldehydes and their corresponding unsubstituted aliphatic aldehydes in the temperature range. The thermodynamic parameters were evaluated from the temperature dependence of the equilibrium monomer concentration: ΔH_ss = ?4.3 ± 0.2 kcal/mole, ΔS_ss = ?21.9 ± 1.0 cal/mole deg, Tc_ss = ?76°C. Not only an ether substitution but also an ester substitution in propionaldehyde caused the decrease in the absolute values of the thermodynamic parameters for the aldehyde polymerization. These substituent effects may have been the result mainly of the strong intermolecular dipole–dipole interactions of polar groups in monomer states.     

Equilibrium anionic polymerization of 4,7-dioxaoctanal and n-octanal

Equilibrium anionic polymerization of 4,7-dioxaoctanal (DOA) and n-octanal (OA) was carried out in tetrahydrofuran in the temperature range of ?90 to ?68°C, and thermodynamic parameters were evaluated as follows: ΔH_ss = ?4.0 ± 0.1 kcal/mole, ΔS_ss = ?18.4 ± 0.5 cal/mole-deg, and T_c,ss = ?56°C for the DOA system; ΔH_sc = ?3.4 ± 0.1 kcal/mole, ΔS_sc = ?15.7 ± 0.4 cal/mole-deg, and T_c,sc = ?59°C for the OA system. Comparison of these values with those in the cases of β-methoxypropionaldehyde and n-valeraldehyde made it clear that the aliphatic aldehyde having a longer alkyl group polymerizes with smaller changes of enthalpy and entropy and that the polar-substituted aldehydes have higher polymerizability than the corresponding unsubstituted aliphatic aldehydes in the temperature range studied. These effects of substituents are interpreted from the viewpoint of the intermolecular interactions of polar groups in monomers and their polymers.     

Kinetics and thermodynamics of anionic polymerization of 2-methoxy-2-oxo-1,3,2-dioxaphosphorinane

Kinetic activation parameters and thermodynamic functions describing the reversible anionic polymerization of 2-methoxy-2-oxo-1,3,2-dioxaphosphorinane (1,3-propylene methyl phosphate) were determined. Enthalpy and entropy of the anionic propagation ? depropagation equilibrium were found to be close to those found previously by the present authors for the cationic polymerization, while the activation parameters of propagation and depropagation differ substantially for both processes and reflect the differences in the involved mechanisms. Thus, data for anionic polymerization (and cationic polymerization in parentheses) are: ΔH_1s° = ?0.7 kcal/mole (?1.1); ΔS_1s° = ?2.8 cal/mole-deg (?5.4); ΔH_p^? = 26.7 kcal/mole, and ΔS_p^? = ?6.1 cal/mole-deg. The polymers obtained have low degrees of polymerization (DP _n ≤ 10) because of the extensive chain transfer, leaving cyclic end groups in macromolecules. The presence, structure and concentration of the end groups have been determined by ¹H-, ³¹P-, and ¹³C-NMR spectra.     

Equilibrium anionic polymerization of the isopropenyl monomers containing aromatic heterocycles

The anionic polymerization of three monomers, 2-isopropenyl-4,5-dimethyloxazole(I), 2-isopropenylthiazole(II), and 2-isopropenylpyridine(III), was studied in THF. These monomers produced red-colored living polymers on addition of sodium naphthalene or living α-methylstyrene tetramer as an initiator. It was observed that a considerable amount of monomer remained in the respective living polymer–monomer system, indicating that an equilibrium between the polymer and the monomer existed as in the case of α-methylstyrene. At lower temperatures, the conversion of the monomer to the polymer increased. The equilibrium monomer concentrations [M_e] were determined at different temperatures, and the heats (ΔH) and the entropies (ΔS°) of polymerization were obtained by plotting In(1/[M_e]) against 1/T as ΔH = ?9.4, ?6.8, and ?6.2 kcal/mole, ΔS°S = ?22.9, ?16.5, and ?16.6, eu for I, II, and III, respectively.     

Anionic polymerization of norbornene trisulfide (exo-3,4,5-trithia-tricyclo[5.2.1.02.6]decane)

The anionic polymerization of norbornene trisulfide initiated with sodium thiophenoxide (sodium cation solvated with dibenzo-18-crown-6 ether) was studied. Polymers with high molecular weights were obtained (M _n up to 10⁵, osmometrically). Molecular weights calculated for living polymerization conditions (i.e., one molecule of initiator yields one macromolecule) agree well with M _n measured by osmometry. ¹H-NMR, ¹³C-{¹H}-NMR, and Raman spectra of the polymer are given. Thermodynamics of polymerization in toluene solvent is described. Enthalpy ΔH_ss = ?(1.39 ± 0.17) kcal mol^?1 and entropy ΔS_ss = ?(7.52 ± 0.55) cal mol^?1 deg^?1 coefficients of polymerization were evaluated from the temperature dependence of the equilibrium monomer concentration determined dilatometrically.     

Equilibrium concentration of trioxane in cationic polymerization

In the cationic polymerization of trioxane and tetraoxane near room temperature, the equilibrium trioxane concentration is not negligible during polymerization. In this work, tetraoxane was polymerized with BF₃ ? O(C₂H₅)₂ in various solvents and the equilibrium concentration of trioxane produced during the polymerization of tetraoxane and equilibrated with the growing polyoxymethylene chain was determined. The equilibrium trioxane concentrations were 0.05, 0.13, and 0.19 mole/l. in benzene, ethylene dichloride, and nitrobenzene at 30°C, respectively, and 0.20 mole/l. in thhylene dichloride at 50°C. The values in ethylene dichloride showed that the approximate values of ΔH_p and ΔS were ?4.2 kcal/mole and ?9.7 cal/mole-deg., respectively.     

Vinyl polymerization. Part 268. Polymerization of acrylonitrile initiated by the system of tetramethyl tetrazene and bromoacetic acid

The polymerization of acrylonitrile (AN) initiated by the system of tetramethyl tetrazene (TMT) and bromoacetic acid (BA) in dimethylformamide (DMF) was studied. The TMT–BA system could initiate the polymerization of AN more easily than TMT alone. The polymerization was confirmed to proceed through a radical mechanism. The initial rate of polymerization R_p was expressed by the equation: R_p = [TMT]^0.62-[BA]^0.5[AN]^1.5. The overall activation energy for the polymerization was estimated as 9.4 kcal/mole. In the absence of monomer, the reaction of TMT with BA in DMF was also studied kinetically by measuring the evolution of nitrogen gas. The reaction was first-order in TMT and first-order in BA; the rate data at 49°C were k₂ = 9.1 × 10^?2l./mole-sec., ΔH? = 17.0 kcal/mole, and ΔS? = ? 6.6 eu. In addition, the treatment of TMT with BA in benzene led to the formation of tetramethylhydrazine radical cation, which was identified by its ESR spectrum. On the other hand, the relatively strong interaction between TMT and DMF was observed by absorption spectrophotometry.     

Das Phenylcarbamylchlorid-Phenylisocyanat-Gleichgewicht in Chlorbenzol

The equilibrium constant for the reaction C₆H₅NHCOCl = C₆H₅NCO + HCl in chlorobenzene solution is K = 0.14 mole/kg at 70°. The approximate values of the enthalpy and the entropy of the reaction are ΔH⁰ = 12 kcal and ΔS⁰ = 31 cal/deg.     

Polymerization of Acrylonitrile Initiated by 1,4-Dimethyl-1,4-bis(p-nitrophenyl)-2-tetrazene

The polymerization of acrylonitrile (AN) initiated by 1,4-dimethyl-1,4-bis(p-nitrophenyl)-2-tetrazene (Ie) was studied in dimethylformamide (DMF) at high temperature. The polymerization proceeds by a radical mechanism. The rate of polymerization is proportional to [Ie]^0.64 and [AN]^1.36. The overall activation energy for the polymerization is 21.5 kcal/mole within the temperature range of 115-130°C. The chain transfer of Ie was also undertaken over the temperature range of 120-135°C. The activation parameters for the decomposition of Ie at 120°C are k_d = 2.78 × 10^?6 sec^?1, ΔH^? = 40.8 kcal/mole, and ΔS^? = 19.5 cal/mole-deg, respectively.     

Polymerization of α-amino acid N-carboxy anhydrides. III. Mechanism of polymerization of L- and DL-alanine NCA in acetonitrile

The polymerization of L - and DL -alanine NCA initiated with n-butylamine was carried out in acetonitrile which is a nonsolvent for polypeptide. The initiation reaction was completed within 60 min.; there was about 10% of conversion of monomer. The number-average degree of polymerization of the polymer obtained increased with the reaction period, and it was found to agree with value of W/I, where W is the weight of the monomer consumed by the polymerization and I is the weight of the initiator used. The initiation reaction of the polymerization was concluded as an attack of n-butylamine on the C₅ carbonyl carbon of NCA. The initiation, was followed by a propagation reaction, in which there was attack by an amino endgroup of the polymer on the C₅ carbonyl carbon of NCA. The rate of polymerization was observed by measuring the CO₂ evolved, and the activation energy was estimated as follows: 6.66 kcal./mole above 30°C. and 1.83 kcal./mole below 30°C. for L -alanine NCA; 15.43 kcal./mole above 30°C., 2.77 kcal./mole below 30°C. for DL -alanine NCA. The activation entropy was about ?43 cal./mole-°K. above 30°C. and ?59 cal./mole-°K. below 30°C. for L -alanine NCA; it was about ?14 cal./mole-°K. above 30°C. and ?56 cal./mole-°K. below 30°C. for DL -alanine NCA. From the polymerization parameters, x-ray diffraction diagrams, infrared spectra, and solubility in water of the polymer, the poly-DL -alanine obtained here at a low temperature was assumed to have a block copolymer structure rather than being a random copolymer of D - and L -alanine.     

Kinetic Study of 1-β-Cyanoethyl Aziridine for Ring-Opening Polymerization Initiated with Alkyl Sulfate

The kinetics of the cationic polymerization of 1-β-cyanoethyl aziridine initiated 3-hydroxy- 1-propane sulfonic acid sultone and methyl tosylate have been studied. The course of polymerization involved the propagation stage and termination reaction due to the reaction between the growing chain and imino groups in the polymer chain. The propagation constants and termination constants were obtained. The enthalpies of activation for the propagation and termination reactions are ΔH_p? = 12.9 kcal/mol and ΔH_t? = 12.4 kcal/mol, and the entropies of activation are ΔS_p? = -31 cal/deg·mol and ΔS_t? = -39 cal/deg·mol. Otherwise, the polymerization initiated with methyl tosylate involved an early stage which was initiated very quickly.     

Kinetics of reactions of Schiff base complexes of iron(II). V. Reactions of the complex of the hexadentate ligand NN‴-bis-[α-(2-pyridyl)benzylidene]triethylenetetramine in acid solution and with hydroxide,cyanide, and peroxodisulphate

The preparation and characterization of the iron(II) complex of the hexadentate Schiff base ligand NN?-bis-[α-(2-pyridyl)benzylidene]triethylenetetramine are reported. Kinetic patterns and rate constants for aquation of this complex, and for its reactions with hydroxide, cyanide, and peroxodisulphate have been determined. Activation parameters for the reaction with cyanide, in aqueous solution, are ΔH? = 24.3 kcal/mole and ΔS? = +1 cal/deg-mole.     

Reaction of tetramethyl-1,2-dioxetane with triphenylphosphine: Activation parameters for the formation of 2,2-dihydro-4,4,5,5-tetramethyl-2,2,2-triphenyl-1,3,2-dioxaphospholane

The reaction of tetramethyl-1,2-dioxetane ( 1 ) and triphenylphosphine ( 2 ) in benzene-d₆ produced 2,2-dihydro-4,4,5,5-tetramethyl-2,2,2-triphenyl-1,3,2-dioxaphospholane ( 3 ) in ?90% yield over the temperature range of 6–60°. Pinacolone and triphenylphosphine oxide ( 4 ) were the major side products [additionally acetone (from thermolysis of 1 ) and tetramethyloxirane ( 5 ) were noted at the higher temperatures]. Thermal decomposition of 3 produced only 4 and 5 . Kinetic studies were carried out by the chemiluminescence method. The rate of phosphorane was found to be first order with respect to each reagent. The activation parameters for the reaction of 1 and 2 were: Ea ? 9.8 ± 0.6 kcal/mole; ΔS^≠ = ?28 eu; k_30° = 1.8 m^?1sec^?1 (range = 10–60°). Preliminary results for the reaction of 1 and tris (p-chlorophenyl)phosphine were: Ea ? 11 kcal/mole, ΔS^≠ = ?24 eu, k_30° = 1.3 M^?1sec^?1 while those for the reaction of 1 and tris(p-anisyl)phosphine were: Ea ? 8.6 kcal/mole, ΔS^≠ = ?29 eu, k_30° = 4.9 M^?1 sec^?1.     

Stereoregularity of poly(alkyl α-chloroacrylates) and mechanism of isotactic polymerization

The catalytic activity of the complexes prepared by the reaction of Grignard reagents with ketones, esters, and an epoxide as polymerization catalysts of methyl and ethyl α-chloroacrylates was investigated. The modifiers which gave isotactic polymers were α,β-unsaturated ketones such as benzalacetophenone, benzalacetone, dibenzalacetone, mesityl oxide, and methyl vinyl ketone, and α,β-unsaturated esters such as ethyl cinnamate, ethyl crotonate, and methyl acrylate. Catalysts with butyl ethyl ketone, propiophenone, and propylene oxide as modifiers produced atactic polymers but no isotactic polymers. It was revealed that the complex catalysts having a structure ? C?C? O? MgX (X is halogen) gave isotactic polymers. The mechanism of isotactic polymerization was discussed. In addition, for radical polymerization of ethyl α-chloroacrylate, enthalpy and entropy differences between isotactic and syndiotactic additions were calculated to give ΔH_i^* ? ΔH_s^* = 910 cal/mole and ΔS_i^* ? ΔS_s^* = 0.82 eu.     

First observation of equilibrium polymerization of cyclic sulfite

Cationic polymerization of a seven-membered cyclic sulfite ( 7CS ) was carried out with methyl trifluoromethanesulfonate as a catalyst in chlorobenzene. The final conversions of 7CS were 22, 41, 52, and 60% in the polymerizations at 25°C with the initial monomer concentrations of 3, 4, 5, and 6M, respectively. The calculated monomer concentration at equilibrium was evaluated as 2.4M in any case. The conversion of 7CS decreased as the polymerization temperature rose. These results support the fact that this polymerization is an equilibrium one. ΔH⁰ and ΔS⁰ in the polymerization were evaliuated as −0.765 kcal/mol and −4.18 cal/mol by Dainton's equation, respectively. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3235–3240, 1997     

Quantitative Line-Shape Analysis of Temperature- and Concentration-Dependent 13C-NMR Spectra of 6Li- and 13C-Labelled Organolithium Compounds. Kinetic and Thermodynamic Data for Exchange Processes in Dibromomethyllithium, (Phenylthio)methyllithium,and Butyllithium

Using the ‘permutation of indices’ method proposed by Kaplan and Fraenkel, we could formulate the density-matrix equations required to fit the temperature-dependent ¹³C-NMR spectra observed with the title compounds. For ⁶Li¹³CHBr₂ ( 1 ) and ⁶Li¹³CH₂SC₆H₅ ( 2 ) an exchange mechanism is proposed by which monomers interchange C- and Li-atoms via a non-observed dimeric intermediate; the activation parameters of these intermolecular dynamic processes have been found to be ΔH^≠ = 10.2 kcal/mol, ΔS^≠ = 13.7 cal/mol·K for 1 and ΔH^≠ = 11.1 kcal/mol, ΔS^≠ = 20.6 cal/mol·K for 2 ((D₈)THF as solvent). In the case of (⁶Li)butyllithium ( 3 ), the observed low-temperature spectra indicate that dimeric ( 3b ) and tetrameric ( 3a ) species are in dynamic equilibrium interchanging the C₃HCH₂ groups (and THF molecules) bonded to the ⁶Li-atoms. The relative concentrations of the dimer and of the tetramer have been determined by peak integration or by line-shape fitting; the ‘pseudo’- equilibrium constant, defined by K′_eq = [ 3b ]²/[ 3a ], was found to be 2.6·10^?2 mol/1 (at ?88°) and corresponds to ΔG_R (?88°) = 2 ΔG°_f( 3b ) – ΔG°_f( 3a ) = 1.34 kcal/mol. The activation parameters of the dynamic process responsible for the exchange were estimated as ΔH^≠ = 3.78 kcal/mol and ΔS^≠ = ?31.3 cal/mol·K. Tentative interpretation of the thermodynamic and kinetic parameters is given.     

Dynamics of a conformational change in aqueous 18-crown-6 by an ultrasonic absorption method

A temperature dependence study of the ultrasonic amplitudes, velocities, and relaxation times for a presumed conformational transition of noncomplexed aqueous 18-crown-6 (1,4,7,10,13,16-hexaoxacyclooctadecane) is discussed. At all temperatures a single relaxation was observed within a 15–255-MHz frequency range. The equilibrium constant for the presumed conformational transition \documentclass{article}\pagestyle{empty}\begin{document}$ {\rm CR}_1 \mathop \rightleftarrows\limits^{K_{12} } {\rm CR}_2 $\end{document} was determined to be K₂₁ = (2 ± 2) × 10^?2. The activation parameters are ΔH₂₁^≠ = 10.2 ± 1.0 kcal/mol, ΔS₂₁^≠ = 7.7 ± 0.2 cal/(mol·deg), ΔH₁₂^≠ = 7.4 ± 1.0 kcal/mol, and ΔS₁₂^≠ = 7.7 ± 0.2 cal/(mol·deg), while the thermodynamic enthalpy and entropy were found to be ?2.6 ± 1.0 kcal/mol and 0 ± 0.2 cal/(mol·deg), respectively. The rate constants at 25.0°C for the presumed conformational transition are k₂₁ = (1.0 ± 0.3) × 10⁷ sec^?1 and k₁₂ = (6.2 ± 0.2) × 10⁸ sec^?1.     

Effects of mercaptides on anionic polymerization. III. Polymerization of methyl methacrylate by thiophenoxides in polar aprotic solvents

Sodium thiophenoxide initiated the polymerization of methyl methacrylate in polar aprotic solvents (DMF, DMSO, HMPA). The active species that initiated the polymerization of the monomer was found by spectrophotometric measurements and by the sodium fusion method to be sodium thiophenoxide itself. The activation energy for the polymerization of the monomer in DMF solvent obtained was E = 3.4 kcal/mole below 30°C, and E = ?3.3 kcal/mole above the temperature. The phenomena were reasoned as the result of the formation of two active species: a solvent-separated ion pair and a contact ion pair. The effects of counterions on the reactivity of thiophenoxide increased with increasing electropositivity of the metals: Li < Na < K. Sodium phenoxide, the oxygen analog of thiophenoxide, was also found to initiate the polymerization of the monomer in the solvents. The relative reactivity of thiophenoxide to phenoxide for the monomer in HMPA at 30°C was thus determined: phenyl-SNa > phenyl-ONa. The relative effect of the polar aprotic solvents on the reactivity of thiophenoxide was also as follows: HMPA > DMF > DMSO. The kinetic studies were made by the graphical evaluation of rate constants. The following results were obtained for the monomer at 20°C in DMF solvent: K_p = 3.5 × 10² 1./mole-hr and K_t = 9.8 × 10^?2/hr.