Surface grafting of polyethylene by mutual irradiation in methyl acrylate vapor. IV. Kinetic analysis by quartz helix microbalances

A detailed kinetic study of the γ-ray-induced surface grafting of methyl acrylate (MA) onto polyethylene (PE) has been investigated by using quartz helix microbalances. Under typical graft conditions, the grafting rate increases, levels off, and then accelerates with irradiation time; i.e., the typical growth process of the surface grafting consists of an initial stage having an increasing rate of grafting, an intermediate stage having a constant rate, and an advanced stage having an accelerated rate. A homopolymer layer (consisting only of an MA component) begins to be formed on the inner graft copolymer layer (consisting both of MA and PE components) at the transition zone in grafting rate after a duration of a constant rate of grafting. Therefore, the increasing rate in increasing rate in the intial stage of grafting reflects the graft copolymerization in the graft copolymer layer (inside the PE sheet), and the increasing rate in the advanced stage reflects the growth of the homopolymer layer. Under grafting reflects the graft tage reflects the growth of the homopolymer layer. Under grafting conditions by which the homolymer layer is not formed throughout the whole grafting process, the surface grafting remains remains in the initial stage. On the order hand, under grafting conditions by which the homopolymer layer begins to be formed from an early stage of grafting, the surface grafting proceeds rapidly from the initial stage to the advanced stage and thus skips the intermediate stage.     

Surface grafting of polyethylene by mutual irradiation in methyl acrylate vapor. II. High-energy electrons irradiation

Vapor-phase mutual grafting of methyl acrylate (MA) onto polyethylene (PE) at high dose rates from an electron accelerator yields the same surface graft structure as does the grafting at low dose rates from ⁶⁰Co sources; i.e., a homopolymer layer (consisting of only MA component) is easily formed on the inner graft copolymer layer (consisting of both MA and PE components) as a result of the continuously increasing surface graft composition. To produce the surface layer, 4-MeV electron irradiation with a linear electron accelerator requires only less than 3 min of irradiation time at dose rates of more than 2 Mrad/min, whereas γ irradiation with a ⁶⁰Co source requires at least 1 hr at dose rates of less than 2 × 10³ rad/min. The rate of monomer consumption (or polymerization) in the surface homopolymer layer shows no dependence of irradiation time and a positive dependence of dose rate. It has been suggested that this kinetic feature at the high dose rates shows some contribution of vapor-phase homopolymerization and subsequent deposition (onto the grafting surface) followed by recombination with the grafted side chain radicals, although secondary graft copolymerization from the grafted chain radicals is still the principal process for the growth of the surface homopolymer layer.     

Surface grafting of polyethylene by mutual irradiation in methyl acrylate vapor. III. Quantitative surface analysis by x-ray photoelectron spectroscopy

X-ray photoelectron spectroscopy (ESCA) has been used for quantitative surface analysis of surface grafts prepared by mutual irradiation of polyethylene (PE) in methyl acrylate (MA) vapor with γ rays and high-energy electrons. The binding-energy shift between the C_1s electrons in the ester group of poly(methyl acrylate) (PMA) and in PE is large enough (ca. 3.6 eV) to distinguish the PMA and PE components. The C_1s peak-area ratio of ester carbon to other carbons is related quantitatively to graft composition by constructing a calibration curve for a given instrument and excitation source, with a series of homogeneous grafts of known composition used as the calibration standards. Using the calibration curve and the measured peak ratio, the surface composition of the surface grafts is determined. The relations between surface compositions according to ESCA and attenuated total reflection (ATR) infrared spectroscopy and between adhesive bond strength and ESCA composition are discussed. In the electron-induced grafts, the grafted surface reaches maximum adhesive bondability with attainment of 100 mole % MA in the surface detected by ESCA; i.e., with formation of a homopolymer layer. The ESCA composition can be used as an indicator of the presence of the homopolymer layer or as a criterion for predicting adhesive bond strength.     

淀粉与丙烯酸甲酯的接枝共聚物作为生物降解塑料的研究

如何解决废弃塑料制品的再资源化和使用无污染的降解塑料是当今人类急待解决的热点课题．淀粉与丙烯酸甲酯（MA）进行接技共聚以制备塑料发泡产品的研究已有报道［‘－‘1，一般认为塑料中淀粉含量在40％以上的产品，很容易在土壤中被微生物降解掉［‘］．这些研究都是在水溶液体系中进行的，本文的目的在于开发高淀粉含量的接校共聚物，为此对比了在3种不同体系（MA－CH3OHA12O三元均相溶液体系，水溶液体系和乳液体系）中得到的接校共聚物的力学性能、形态观察与组成情况，发现单纯追求高接技效率与接枝链MA的高分子量并不一定能得到…     

Process parameters and their effect on grafting reactions in core/shell latexes

The grafting of methyl methacrylate (MMA) onto polybutadiene (PB) latexes prepared by seeded emulsion polymerization at 50°C was investigated as a function of: (a) initiator concentration used in the secondary polymerization, (b) monomer-to-polymer ratio, (c) the specific surface area of the seed latex, and (d) the degree of conversion. The thin layer chromatography/flame ionization detection (TLC/FID) technique was used to determine the proportion of graft copolymer in the core/shell latex, It was found that grafting PMMA onto PB depended upon the concentration of initiator, decreasing as the concentration was increased. The amount of grafting increased with increasing specific surface area of the seed latex, while the molecular weight of the acetone-soluble graft copolymer decreased. The amount of graft copolymer was found to decrease concurrently with increasing monomer-to-polymer ratio and degree of conversion. These results suggest a hydrogen abstraction mechanism in the formation of graft PB–PMMA through a chain transfer process.     

Solution properties of poly(methyl acrylate) and (1:1) poly(styrene-co-methyl acrylate)

Poly(methyl acrylate) (PMA) and 1:1 poly(styrene-co-methyl acrylate) (PSMA) were prepared by solution and bulk polymerization, respectively. The copolymer was analyzed with NMR to ascertain its composition and microstructure. The solution properties of unfractionated PMA and fractionated PSMA in ethyl acetate were investigated by light-scattering and viscosity techniques at 35°C. Narrow composition heterogeneity as revealed from the light-scattering measurements in different solvents justified the use of a single solvent for the copolymer characterization. The equations relating the limiting viscosity number to molecular weight, the molecular dimension to molecular weight, etc., were found for homopolymer and copolymers in ethyl acetate at 35°C. In the evaluation of the Flory constant K for the unperturbed state by methods based on Flory-Fox-Schaefgen, Kurata-Stockmayer, and Stockmayer-Fixman expressions, only the first method gave a value for PMA in ethyl acetate, consistent with that obtained in other solvents, whereas similar values of K were obtained by the three methods for PSMA in ethyl acetate. The studies indicate reduced thermodynamic interaction for PSMA–ethyl acetate compared to PMA–ethyl acetate, but increased steric effect in the copolymer compared with the homopolymer.     

氯化原位接枝反应制备羟基官能化CPE——结构表征

以高密度聚乙烯(HDPE)为基体,采用气-固氯化原位接枝反应合成了以氯化聚乙烯(CPE)为骨架聚合物、丙烯酸-2羟基乙酯(HEA)为支链的接枝共聚物.反应中不需要加入任何引发剂,以氯自由基引发接枝及氯代反应,得到羟基官能化CPE接枝聚合物.并用1H-NMR,FT-IR,GPC及X-射线衍射等对接枝共聚物的结构进行了表征.     

聚苯乙烯大单体与丙烯酸酯接枝共聚物对聚苯乙烯表面的改性研究

研究了由大单体技术合成的侧链为聚苯乙烯、骨架由丙烯酸丁酯或甲基丙烯酸羟乙酯/丙烯酸丁酯组成的接枝共聚物对聚苯乙烯的表面改性效果(试样浇注于玻璃纸上成膜)。发现仅添加0.5wt％的接枝共聚物就可完全改变聚苯乙烯膜两面的临界表面张力γ-c与表面能中的色散力部份γ_s~D,少量添加的接枝共聚物在改性聚苯乙烯膜的两面呈现出明显的表面富集现象。虽然两类接枝共聚物的极性有较大的差异,但改性聚苯乙烯成膜后的自由表面均显示出与聚丙烯酸丁酯相同的低表面能(γ_s~D=37×10~(-3)牛顿·米~(-1)),而添加三元接枝共聚物的改性膜与玻璃纸接触的表面却具有高于聚苯乙烯的表面能|(γ_s~D=54×10(-3)牛顿·米~(-1))。这种改性膜的两面具有不同的表面能是由于接枝共聚物中不同的组分在膜的两面富集所致,已通过ESCA的表面测试结果证实,并与按Gibbs吸附式的计算值相符。     

Two‐dimensional chromatography of complex polymers. IV. Analysis of the grafting reaction of methyl methacrylate onto polybutadiene

The grafting reaction of methyl methacrylate onto polybutadiene (PB) was investigated with different chromatographic techniques, including high‐performance liquid chromatography (HPLC) and online coupled two‐dimensional liquid chromatography. As a result of the grafting reaction, a complex mixture of nongrafted PB, the graft copolymer PB‐g‐PMMA [where PMMA is poly(methyl methacrylate)], and the PMMA homopolymer was formed. The complete separation of all the products of the grafting reaction was achieved with gradient HPLC. By the combination of gradient HPLC and size exclusion chromatography in a fully automated two‐dimensional chromatography setup, the complex distributions of the chemical composition and molar mass were fingerprinted simultaneously. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3143–3148, 2003     

Surface modification of silicate glass using 3-(mercaptopropyl)trimethoxysilane for thiol-ene polymerization

A thiol-ene polymerization was accomplished on silicate glass slides to graft a series of homopolymers and copolymers using 3-(mercaptopropyl)trimethoxysilane (MTS) as both a silane coupling agent and initiator. MTS was initially covalently bonded to an acid cleaned glass surface via a classical sol-gel reaction. Poly(acrylic acid) (PAA), poly(acrylamide) (PAAm), poly(methyl acrylate) (PMA), poly(acrylamido-2-methyl-propanesulfonic acid) (PAMPS), and the copolymer poly(AA-co-AAm-co-MA-co-AMPS) were grafted from the thiol group of MTS. The surface chemistry of the MTS modified slides and polymer grafts was characterized with attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS). Surface texture was evaluated with tapping mode atomic force microscopy (TM-AFM). The Owens-Wendt-Kaelble (OWK) and Lifshitz-van der Waals acid-base (LW-AB) methods were used to evaluate surface energies by sessile drop contact angle method. The synthetic approach demonstrated a facile, rapid method for grafting to glass surfaces.     

Synthesis of double hydrophilic graft copolymer containing poly(ethylene glycol) and poly(methacrylic acid) side chains via successive ATRP

A well‐defined double hydrophilic graft copolymer, with polyacrylate as backbone, hydrophilic poly(ethylene glycol) and poly(methacrylic acid) as side chains, was synthesized via successive atom transfer radical polymerization followed by the selective hydrolysis of poly(methoxymethyl methacrylate) side chains. The grafting‐through strategy was first used to prepare poly[poly(ethylene glycol) methyl ether acrylate] comb copolymer. The obtained comb copolymer was transformed into macroinitiator by reacting with lithium diisopropylamine and 2‐bromopropionyl chloride. Afterwards, grafting‐from route was employed for the synthesis of poly[poly(ethylene glycol) methyl ether acrylate]‐g‐poly(methoxymethyl methacrylate) amphiphilic graft copolymer. The molecular weight distribution of this amphiphilic graft copolymer was narrow. Poly(methoxymethyl methacrylate) side chains were connected to polyacrylate backbone through stable C? C bonds instead of ester connections. The final product, poly[poly(ethylene glycol) methyl ether acrylate]‐g‐poly(methacrylate acid), was obtained by selective hydrolysis of poly(methoxymethyl methacrylate) side chains under mild conditions without affecting the polyacrylate backbone. This double hydrophilic graft copolymer was found be stimuli‐responsive to pH and ionic strength. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4056–4069, 2008     

Vapor-phase graft copolymerization of binary solid monomers onto poly(ethylene-co-vinyl acetate) film by ultraviolet irradiation

Vapor-phase graft copolymerizations of acenaphthylene–maleimide or acenaphthylene–maleic anhydride binary solid monomers onto poly(ethylene-co-vinyl acetate) films were carried out under ultraviolet irradiation. The extent of sorption of single or binary monomers increased with the increasing vinyl acetate content in the backbone polymers. The sorbed binary monomers were mainly composed of acenaphthylene, but the maleimide or maleic anhydride fraction increased with the increasing vinyl acetate content of the films and the composition was little affected by surface hydrolysis. In all series of graft polymerization of single or binary monomers the overall extent of grafting increased with the vinyl acetate content and was suppressed by the surface hydrolysis of the backbone film. The composition of the grafted copolymer, however, differed markedly, depending on the combination of binary monomers. The grafted copolymer in the acenaphthylene–maleimide system was composed mainly of acenaphthylene units, whereas that in the acenaphthylene–maleic anhydride system was composed mainly of maleic anhydride units. The results were compared with those of γ-ray grafting, and it was suggested that the contribution of a direct supply of monomers from vapor phase and the existence of an acetoxy group on the surface of the film should play an important role in the grafting reaction.     

Crystallization behavior, thermal property and biodegradation of poly(3-hydroxybutyrate)/poly(ethylene glycol) grafting copolymer

The poly(3-hydroxybutyrate)(PHB)/poly(ethylene glycol)(PEG) grafting copolymer was successfully prepared by PHB and acrylate groups ended PEGM using AIBN as initiator. The crystallization behavior, thermal stability and environmental biodegradability of PHB/PEG grafting copolymers were investigated with differential scanning calorimetry (DSC), Thermogravimetric analysis (TGA), wide angle X-ray diffraction (WAXD), scanning electron microscopy (SEM), and Biodegradation test in vitro. In the results, all the grafting copolymers were found to show the X-ray diffraction arising from the PHB crystal lattice, while none of the PEG crystallized peaks could be found even though the graft percent reached 20%. This result indicated that PEG molecules were randomly grafted onto PHB chain. The thermal properties measured by DSC showed that the melting temperature(T_m) and glass transition temperature (T_g) were both shifted to lower temperature with the graft percent increasing, and this broadened the narrow processability window of PHB. According to TGA results, the thermal stability of the grafting copolymers is not changed compared to pure PHB. From the biodegradation test, it could be concluded that degradation occurred gradually from the surface to the inside and that the degradation rate could be adjusted by the PEG grafting ratio. In another words, the biodegradation profiles of PHB/PEG grafting copolymer can be controlled. These properties make PHB/PEG grafting copolymer have promising potential applications especially in agriculture fields.     

Functional Polyolefins: Poly(ethylene)‐graft‐Poly(tert‐butyl acrylate) via Atom Transfer Radical Polymerization From a Polybrominated Alkane

Poly(cis‐cyclooctene) is synthesized via ring‐opening metathesis polymerization in the presence of a chain‐transfer agent and quantitatively hydrobrominated. Subsequent graft polymerization of tert‐butyl acrylate (tBA) via Cu‐catalyzed atom transfer radical polymerization (ATRP) from the non‐activated secondary alkyl bromide moieties finally results in PE‐g‐PtBA copolymer brushes. By varying the reaction conditions, a series of well‐defined graft copolymers with different graft densities and graft lengths are prepared. The maximum extent of grafting in terms of bromoalkyl groups involved is approximately 80 mol%. DSC measurements on the obtained graft copolymers reveal a decrease in T_m with increasing grafting density.     

Graft copolymerization of methyl methacrylate onto lignosulfonate by H2O2–Fe(II) redox system. I. Preparation and characterization of the graft copolymer

Graft copolymerization of methyl methacrylate onto lignosulfonate in aqueous medium was investigated. It was found that the H₂O₂–Fe(II) redox system is very effective for the grafting (E_a = 4.4 kcal/mole). The H₂O₂/Fe²⁺ ratio was the most important factor in the graft copolymerization and characteristics of the resultant graft copolymers. In most cases, polymerization for 100 min at 30°C was enough to obtain 80% conversion and 50–60% grafting efficiency. The resultant polymer mixture was subjected to extraction alternately with acetone and water, and the graft copolymer was isolated free from homopolymer and unreacted lignosulfonate. With increasing H₂O₂/Fe²⁺ ratio, the grafting ratio showed a maximum at 4, whereas the yield of graft copolymer and number of poly(methyl methacrylate) branches for every building unit of lignosulfonate increased up to a ratio of 4, both values, however, remaining constant above 4. The graft copolymer obtained for the case H₂O₂/Fe²⁺ = 4 consisted of one part of lignosulfonate and five parts of poly(methyl methacrylate). The number of branches in the graft copolymer was 6 × 10^?3/OCH³ or one every 167 guaiacyl nuclei.     

Effect of comonomer sorption on radiation-induced copolymer grafting onto polyethylene and EVA films in the vapor phase

Radiation-induced copolymer grafting of acenaphthylene and maleic anhydride onto polyethylene or EVA film in the vapor phase was carried out and the effect of comonomer sorption on the grafting was studied. When polyethylene film was used as a backbone polymer, the sorption of the binary monomers during the grafting increased linearly as the grafting reaction proceeded. The marked increase was probably caused by the formation of a grafted layer. Particularly, the sorption of maleic anhydride was brought about by the existence of a grafted layer. In grafting onto EVA film, the content of maleic anhddride in the grafted copolymer increased with the increasing content of vinyl acetate in EVA. Continuous measurements of sorption of the comonomers onto EVA and grafted EVA films were carried out by use of an electrobalance. The distinctive feature of the sorption was that the equilibrium sorption of acenaphthylene or maleic anhydride onto the grafted EVA film increased and the diffusion constants for both comonomers decreased markedly with increasing percentage of graft. The copolymer grafting was explained from these results by assuming that the monomer molecules are supplied to the propagating chain ends mostly through a sorbed state on the polymer film.     

Grafting onto poly(vinyl alcohol). II. Graft copolymerization of methyl acrylate and vinyl acetate and their binary mixture using γ-rays as initiator

Methyl acrylate (MA), vinyl acetate (VAc) and their binary mixture (MA + VAc) have been graft copolymerized onto poly(vinyl alcohol) using γ-rays as initiator by mutual radiation method in aqueous medium. The optimum conditions for affording maximum grafting have been evaluated. The percentage of grafting has been determined as a function of total dose, concentrations of poly(vinyl alcohol), MA, VAc, and their binary mixture. Rate of grafting (R_p) and induction period (I_p) have been determined as a function of total initial mixed monomer concentration and concentration of poly(vinyl alcohol). The graft copolymer has been characterized by thermogravimetric method. The effect of donor monomer (vinyl acetate) on percent grafting of acceptor monomer (methyl acrylate) has been explained.     

The preparation,characterization, and application of cellulose–MMA graft copolymers. I. The aqueous-based preparation of cellulose–MMA graft copolymers

Cellulose-MMA graft copolymers have been produced using aqueous-based, Ce(IV)-initiated and periodate-initiated systems and also photochemical initiation. The reaction variables studied include the effect on grafting of varying the MMA monomer concentration, the initiator type and concentration, and also the reaction time. Of the three initiator types examined, the Ce (IV)-initiated and the photochemically-initiated systems are comparable in their effects on graft copolymer formation. Concurrent homopolymer formation was in the region of 50% by weight. Periodate-initiation leads to less efficient grafting of MMA onto cellulose, although homopolymer formation is also lower (typically <20% by weight). The characterization of the copolymeric products through their properties as solids and, as their carbanilated derivatives, through their solution properties has been undertaken. Values of the activation onergy of decomposition (E_A) of the cellulose-MMA graft copolymers decrease with increasing MMA content, ranging between 227 and 155kJ mol^?1. There is also a dependence on initiator type and grafting reaction conditions used (E_A (cellulose wood pulp) = 239 kJ mol^?1; E_A (PMMA) = 115 kJ mol^?1). Quantitative zeta-potential (ζ) determinations for cellulose-MMA graft copolymer samples produce negative surface charge density (σ) values. At a comparable MMA grafting level of 70–80%, values are of the order: photochemical (?730 esu/cm²) > periodate (?470 esu/cm²) > Ce (IV)-initiation (?351 esu/cm²). Characterization of carbanilate solutions (by rheological examination) and of dry, carbanilate films (by study of surface wetting behavior) highlighted differences in the physical conformation of copolymers prepared by the different initiation routes. The highly degradative effect on cellulose of a periodate initiator, in comparison with the Ce (IV)-initiation system, is reflected in significantly reduced molar mass values (typically, M_n 65,000 as opposed to 130,000 for Ce (IV)-initiated graft copolymer carbanilates).     

Synthesis of PMHDO‐g‐PDEAEA well‐defined amphiphilic graft copolymer via successive living coordination polymerization and SET‐LRP

A series of well‐defined amphiphilic graft copolymer containing hydrophobic polyallene‐based backbone and hydrophilic poly(2‐(diethylamino)ethyl acrylate) (PDEAEA) side chains was synthesized by sequential living coordination polymerization of 6‐methyl‐1,2‐heptadiene‐4‐ol (MHDO) and single electron transfer‐living radical polymerization (SET‐LRP) of 2‐(diethylamino)ethyl acrylate (DEAEA). Ni‐catalyzed living coordination polymerization of MHDO was first performed in toluene to give a well‐defined double‐bond‐containing poly(6‐methyl‐1,2‐heptadiene‐4‐ol) (PMHDO) homopolymer with a low polydispersity (M_w/M_n = 1.10). Next, 2‐chloropropionyl chloride was used for the esterification of pendant hydroxyls in every repeating unit of the homopolymer so that the homopolymer was converted to PMHDO‐Cl macroinitiator. Finally, SET‐LRP of DEAEA was initiated by the macroinitiator in tetrahydrofuran/H₂O using CuCl/tris(2‐(dimethylamino)ethyl)amine as catalytic system to afford well‐defined PMHDO‐g‐PDEAEA graft copolymers (M_w/M_n ≤ 1.22) through the grafting‐from strategy. The critical micelle concentration (cmc) was determined by ?uorescence spectroscopy with N‐phenyl‐1‐naphthylamine as probe and the micellar morphology was visualized by transmission electron microscopy. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of pH-responsive polysilane with polyelectrolyte side chains through γ-ray-induced graft polymerization

Polysilanes with polyelectrolyte side chains are synthesized by two methods utilizing γ-ray-induced grafting and the pH responsiveness for one of those polymers is revealed mainly by investigating interfacial behavior of its monolayer at the air/water interface. In the first synthetic method, poly(methyl acrylate) is grafted onto poly(methyl-n-propylsilane) (PMPrS) through γ-ray-induced grafting, and then the PMA chains are hydrolyzed to poly(acrylic acid) resulting in the yield of ca. 97%. Thus PMPrS with polyelectrolyte side chains is successfully synthesized by the graft chain hydrolysis. The other method is the direct grafting of electrolyte monomers. Poly(methacrylic acid)-grafted PMPrS (PMPrS-g-PMAA) can be obtained through γ-ray-induced grafting of methacrylic acid monomers onto PMPrS chains, which shows the effectiveness of radiation grafting for the synthesis of polyelectrolyte graft copolymers. PMPrS-g-PMAA exhibits pH responsive behavior. In addition to the pH-dependence of water solubility, interfacial behavior also depends on the pH. Langmuir monolayers of PMPrS-g-PMAA exhibit different surface pressure-area isotherms according to the grafting yield and the pH of the subphase water. This result suggests that radiation modification is useful for fabricating polysilane-based ordered materials responsive to outer stimuli.