Selective and rapid determination of biogenic amines by capillary zone electrophoresis

Summary A rapid separation of 21 amines by high-performance capillary zone electrophoresis with indirect photometric detection is presented. The electrolyte is based on copper(II) as primary constituent. Factors affecting the separation by this electrolyte have been investigated and include the composition of the buffer, the voltage, the temperature and the mode of injection. External calibration was used to characterize the analytical response to each amine. The detection limits were approximately 0.05 μg mL⁻¹ for almost all the amines. After electrokinetic or hydrodynamic injection calibration plots of peak area against concentration were linear between 0.05 and 10 μg mL⁻¹. The method has been applied to the analysis of biogenic amines in synthetic samples; the recoveries of the amines from such samples, determined by the standard addition technique, were in the range 90 to 110%.     

Influence of injection parameters on column performance in nanoscale high-performance liquid chromatography

Summary The influence of the injection volume and the sample solvent on column efficiency has been evaluated in packed nano liquid chromatography using columns 150μ i.d. Evaluation of column performance was by means of reduced plate height (h) versus reduced velocity (v) for four polyaromatic hydrocarbon test compounds (PAHs). When compounds are dissolved in a weak solvent (such as MeCN: H₂O, 30∶70), and whatever the injection volume −60 or 200 nL-a gain in efficiency can be observed due to the well-known on-column focusing phenomenon, but keeping constant solute retention factors. Under optimized conditions (flow rate: 150 nLmin⁻¹, solvent sample MeCN: H₂O, 30∶70, injection volume 200 nL), a reduced plate height of 1.83 has been obtained for a 15 μm C₁₈ packing corresponding to 36000 plates m⁻¹, which illustrates the absence of any extracolumn band broadening under nano LC conditions.     

Determination of ascorbic acid by use of a flow-through solid phase UV spectrophotometric system

A continuous flow-through solid phase spectrophotometric system was developed for the determination of ascorbic acid based on the measurement of its intrinsic absorbance in the UV region when retained on a 1 mm Sephadex QAE A-25 anion exchanger gel layer which is placed into an appropriate quartz flow-through cell, the absorbance exhibited by this solid phase being monitored at 267 nm. A monochannel manifold was used, the sample (300, 600 or 1000 μL) being injected into the carrier solution (acetate buffer). This solution also elutes the analyte after developing the analytical signal, and regenerates the resin layer which, therefore, remains ready for the next sample. The linear dynamic range and other analytical parameters vary according to the sample volume injected. Three calibration lines were established for 300, 600 and 1000 μL sample volume, which ranged from 1.0 to 20.0, 0.5 to 10.0 and 0.2 to 6.0 μg mL^–1, respectively. The detection limits were 0.04 (300 μL), 0.03 (600 μL) and 0.02 μg mL^–1 (1000 μL), the sampling rates 28, 24 and 21 h^–1, and the RSDs (n = 10) 0.87%, 1.08% and 0.90%, respectively. The amount of ascorbic acid in various samples (pharmaceuticals, sweets and urine) were successfully determined with this method. Received: 28 April 1998 / Revised: 3 June 1998 / Accepted: 30 June 1998     

Determination of ascorbic acid by use of a flow-through solid phase UV spectrophotometric system

A continuous flow-through solid phase spectrophotometric system was developed for the determination of ascorbic acid based on the measurement of its intrinsic absorbance in the UV region when retained on a 1 mm Sephadex QAE A-25 anion exchanger gel layer which is placed into an appropriate quartz flow-through cell, the absorbance exhibited by this solid phase being monitored at 267 nm. A monochannel manifold was used, the sample (300, 600 or 1000 μL) being injected into the carrier solution (acetate buffer). This solution also elutes the analyte after developing the analytical signal, and regenerates the resin layer which, therefore, remains ready for the next sample. The linear dynamic range and other analytical parameters vary according to the sample volume injected. Three calibration lines were established for 300, 600 and 1000 μL sample volume, which ranged from 1.0 to 20.0, 0.5 to 10.0 and 0.2 to 6.0 μg mL^–1, respectively. The detection limits were 0.04 (300 μL), 0.03 (600 μL) and 0.02 μg mL^–1 (1000 μL), the sampling rates 28, 24 and 21 h^–1, and the RSDs (n = 10) 0.87%, 1.08% and 0.90%, respectively. The amount of ascorbic acid in various samples (pharmaceuticals, sweets and urine) were successfully determined with this method. Received: 28 April 1998 / Revised: 3 June 1998 / Accepted: 30 June 1998     

Liquid chromatographic determination of aliphatic amines in water using solid support assisted derivatization with 9-fluorenylmethyl chloroformate

Summary A simple and sensitive method has been developed for the liquid chromatographic determination of short-chain aliphatic amines in water. Analytes are retained in solid-phase extraction (SPE) cartridges, and then derivatized by drawing an aliquot of the fluorogeneic reagent 9-fluorenylmethyl chloroformate (FMOC) through the cartridges. After a certain reaction time the derivatives formed are desorbed with acetonitrile. The collected extracts are then chromatographed on a LiChrospher 100 RP₁₈ 125 mm×4 mm i.d., 5 μm, column using an acetonitrile-water gradient. The influence of experimental conditions (SPE material, volume of sample, concentration of FMOC, time of reaction and pH) has been investigated. Optimal results have been obtained with C₁₈ SPE cartridges using a sample volume of 5.0 mL. For derivatization, 0.25 mL aliquots of 25 mM FMOC have been used, the reaction time being only 2 min. The method has been applied to the quantification of several aliphatic amines: methylamine, ethylamine, dimethylamine,n-butylamine,n-pentylamine andn-hexylamine. Under the proposed conditions the percentages of analytes retained plus derivatized were of about 54–107% compared to those obtained with direct solution derivatization. The method provided good reproducibility, linearity and accuracy within the 0.050–1.0 mg L⁻¹ concentration range. The limits of detection were in the 0.25–5.0 μg L⁻¹ range. The utility of the described approach has been tested by analysing tap water, river water and industrial waste water.     

Multiresidue procedures for determination of triazine and organophosphorus pesticides in water by use of large-volume PTV injection in gas chromatography

Summary Two procedures, based on large-volume injection with a programmed-temperature vaporizer (PTV), have been developed for the determination of several triazine and organophosphorus pesticides. The use of PTV for injection in gas chromatography (GC) has enabled the introduction of up to 200 μL sample extract into the GC, thus increasing the sensitivity of the method. PTV injection has been combined off-line with two different microextraction procedures—liquid-liquid partition and solid-phase extraction. A simple and rapid off-line liquid-liquid microextraction procedure (5 mL water/1 mL methyltert-butyl ether) was applied to surface water samples spiked at levels between 0.01 and 5μg L⁻¹. Recoveries of the overall procedure were >80% and the precision was better than 15%. Detection limits were <30 ngL⁻¹ from 200-μL injections in GC-NPD analysis of triazines and GC-FPD analysis of organophosphorus pesticides. Off-line automated solid-phase extraction with C₁₈ cartridges has been applied to water samples (50 mL) spiked at 0.01, 0.1 and 1 μg L⁻¹. The overall procedure was satisfactory (recoveries >80% and coefficients of variation <12%) and the limits of detection ranged from 1 to 9 ng L⁻¹. Finally, several surface water samples were anlysed, and triazine herbicides were detected at concentrations of approx. 0.1–0.2 μg L⁻¹. The results were similar to those obtained by conventional solvent extraction then GC-MSD after splitless injection of 2 μL.     

Automatic determination of phylloquinone in vegetables and fruits using on-line photochemical reduction and fluorescence detection via solid phase extraction and flow injection

A very simple, rapid and highly sensitive flow injection fluorimetric method was developed for the determination of phylloquinone. The assay was based on the on-line reduction of phylloquinone in dodecylsulfate micelles after irradiation with UV light. The micellar medium enhanced the fluorescence and stability of the reduced phylloquinone. Under optimum experimental conditions, the range of application of the technique was between 0.09 and 45.0 μg mL⁻¹ and the detection limit was 0.05 μg mL⁻¹. The sample throughput was 90 injections per hour. The reliability of the method for the routine analysis of phylloquinone in vegetables and fruits is demonstrated. Extractions were made with hexane, and an automated solid phase extraction system was used to purify the sample extracts prior to injection into the flow injection manifold.     

Determination of Trihalomethanes in Drinking Water by Dispersive Liquid–Liquid Microextraction then Gas Chromatography with Electron-Capture Detection

Dispersive liquid–liquid microextraction (DLLME) has been used for preconcentration of trihalomethanes (THMs) in drinking water. In DLLME an appropriate mixture of an extraction solvent (20.0 μL carbon disulfide) and a disperser solvent (0.50 mL acetone) was used to form a cloudy solution from a 5.00-mL aqueous sample containing the analytes. After phase separation by centrifugation the enriched analytes in the settled phase (6.5 ± 0.3 μL) were determined by gas chromatography with electron-capture detection (GC–ECD). Different experimental conditions, for example type and volume of extraction solvent, type and volume of disperser solvent, extraction time, and use of salt, were investigated. After optimization of the conditions the enrichment factor ranged from 116 to 355 and the limit of detection from 0.005 to 0.040 μg L⁻¹. The linear range was 0.01–50 μg L⁻¹ (more than three orders of magnitude). Relative standard deviations (RSDs) for 2.00 μg L⁻¹ THMs in water, with internal standard, were in the range 1.3–5.9% (n = 5); without internal standard they were in the range 3.7–8.6% (n = 5). The method was successfully used for extraction and determination of THMs in drinking water. The results showed that total concentrations of THMs in drinking water from two areas of Tehran, Iran, were approximately 10.9 and 14.1 μg L⁻¹. Relative recoveries from samples of drinking water spiked at levels of 2.00 and 5.00 μg L⁻¹ were 95.0–107.8 and 92.2–100.9%, respectively. Comparison of this method with other methods indicates DLLME is a very simple and rapid (less than 2 min) method which requires a small volume of sample (5 mL).     

Flow injection spectrophotometric determination of iron(III) using diphenylamine-4-sulfonic acid sodium salt

A highly sensitive and very simple spectrophotometric flow-injection analysis (FIA) method for the determination of iron(III) at low concentration levels is presented. The method is based on the measurement of absorbance intensity of the red complex at 410 nm formed by iron(III) and diphenylamine-4-sulfonic acid sodium salt (DPA-4-SA). It is a simple, highly sensitive, fast, and low cost alternative method using the color developing reagent DPA-4-SA in acetate buffer at pH 5.50 and the flow-rate of 1 mL min⁻¹ with the sample throughput of 60 h⁻¹. The method provided a linear determination range between 5 μg L⁻¹ and 200 μg L⁻¹ with the detection limit (3S) of 1 μg L⁻¹ of iron(III) using the injection volume of 20 μL. FIA variables influencing the system performance were optimized. The amount of iron(III) and total iron in river and seawater samples was successfully determined. Repeatability of the measurements was satisfactory at the relative standard deviation of 3.5 % for 5 determinations of 10 μg L⁻¹ iron(III). The accuracy of the method was evaluated using the standard addition method and checked by the analysis of the certified material Std Zn/Al/Cu 43 XZ3F.     

Direct analysis of crude plasma samples by turbulent flow chromatography/tandem mass spectrometry

Summary Turbulent flow chromatography coupled to tandem mass spectrometry (TFC-MS-MS) has recently emerged as a potentially fast, sensitive and specific technique for the direct analysis of pharmaceutical compounds from crude plasma. TFC-MS-MS removes the need for time-consuming sample preparation procedures such as solid-phase extraction (SPE) or liquid-liquid extraction (LLE). A relatively high flow rate combined with the use, of an HPLC column with large porous particles allows the on-line clean up and quantification of compounds in plasma samples. Until, now, the amount of plasma directly injected into TFC systems has rarely exceeded 30 μL in order to prevent rapid column degradation. Increasing the injection volume also induces high carry-over levels, particularly for drugs with basic and/or lipophilic properties. This paper describes the first genetic TFC-MS-MS method developed in a 96-well format, which allows the direct injection of 200 μL of 1∶1 diluted plasma (equivalent to 100 μL neat plasma). An average, of 390 injections was carried out with each extraction column. More than 2000 dog plasma samples were injected into the system without any sign of carryover. The method was fully validated over a 5–500 ng mL⁻¹ range for three basic compounds: doxazosin, CP122,288 and dofetilide. The imprecision was 1.2 to 8.3% for doxazosin, 1.5 to 4% for CP122,288 and 1.6 to 9.2% for dofetilide. The inaccuracy ranged from 6% to 7.9%. This generic methodology was then used to assay two structurally unrelated development compounds, showing that the method accuracy and sensitivity were adequate for the early pharmacokinetic (PK) studies in animals.     

Determination of Low-Level Ethylenediaminetetraacetic Acid in Water Samples by Ion Chromatography with Ultraviolet Detection

A convenient and sensitive ion chromatographic (IC) method for the analysis of ethylenediaminetetraacetic acid (EDTA) in water samples was proposed. Using a fast reversible reaction of free EDTA and metal–EDTA complexes into Fe(III)–EDTA complex in the presence of Fe(III) ions, sample solutions were applied to an ion-exchange column using a mobile phase (pH 2.3), which was composed of 100 μM Fe(III) chloride and 5 mM methanesulfonic acid. The addition of Fe(III) solution (100 μL) containing 10 mM Fe(III) chloride and 0.5 M methanesulfonic acid to the sample solution (10 mL) permitted the injection of a large volume (400 μL) of sample, which allowed for greater sensitivity. The proposed IC method gave a highly linear (r ² > 0.999) calibration curve ranging 0.005–1.0 μM EDTA and had a limit of detection of 1.5 nM. High repeatability (RSD < 2.1%) and recoveries (88–108%) were also obtained. With this method, total EDTA level in raw and drinking waters were analyzed successfully.     

Semi-micro size-exclusion chromatography: Molecular-weight measurement of poly (ethylene terephthalate) and separation of oligomers and prepolymers

Summary Several polystyrene gels of different pore sizes were packed into a 500 mm×2.1 mm I.D. column. Semi-micro size-exclusion chromatography (SEC) using these columns was carried out with a system consisting of a triple piston pump, a micro loop injector and a flow cell with 1.0-μl cell volume constructed for semi-micro HPLC, because the dead volume of the injector and the cell volume of flow cell for conventional HPLC caused a significant loss in column efficiency. The effects of sample amount, injection volume and mobile phase flow rate on column efficiency and retention volume were examined and the optimized operational variables of the sample amount (below 500 μg), the injection volume (less than 15 μl) and the flow rate range (30–70 μl/min) determiend for semi-micro SEC. Oligostyrene, epoxy resin, phenol-formaldehyde resin and phthalates were analyzed by the optimized semi-micro SEC system under the given conditions. In addition, molecular weight distribution of four different poly(ethylene terephthalate) films was successfully measured by using a mixture of chloroform and hexafluoroisopropanol as the eluent.     

Determination of trace amounts of lead in mussels by flow-injection flame atomic-absorption spectrometry coupled with on-line minicolumn preconcentration

A minicolumn packed with poly(aminophosphonic acid) chelating resin incorporated in an on-line preconcentration system for flame atomic-absorption spectrometry was used to determine ultratrace amounts of lead in mussel samples at μg L^–1 level. The preconcentrated lead was eluted with hydrochloric acid and injected directly into the nebulizer for atomization in an air-acetylene flame for measurement. The performance characteristics of the determination of lead were: preconcentration factor 26.8 for 1 min preconcentration time, detection limit (3σ) in the sample digest was 0.25 μg g^–1 (dry weight) for a sample volume of 3.5 mL and 0.2 g sample (preconcentration time 1 min), precision (RSD) 2.3% for 25 μg L^–1 and 2.0% for 50 μg L^–1. The sampling frequency was 45 h^–1. The method was highly tolerant of interferences, and the results obtained for the determination of lead in a reference material testify to the applicability of the proposed procedure to the determination of lead at ultratrace level in biological materials such as mussel samples. Received: 1 November 2000 / Revised: 8 January 2001/ Accepted: 11 January 2001     

Comparison of adsorbents for on-line solid-phase extraction of polycyclic aromatic hydrocarbons before liquid chromatography with UV detection

Summary On-line solid-phase extraction (SPE) coupled with reversed-phase liquid chromatography and UV detection at 254 nm has been used for the determination of trace-level polycyclic aromatic hydrocarbons (PAH) in soil extracts. Five commercially available adsorbents (C₈, C₁₈, PLRP-S, PRP-1, and Bond-Elut Env) were evaluated. Results showed that recovery of the PAH decreased with increasing molecular weight, because of their poorer solubility. Recovery of high-molecular-weight PAH was significantly improved by addition of 10% (v/v) acetonitrile to the sample before loading of the SPE adsorbent. PAH recovery ranged from 64.0 to 108% when a 50 mL sample spiked with 1 μg L⁻¹ was applied to these adsorbents. Determination of PAH was possible with detection limits below 0.05 μg L⁻¹, which corresponds to 0.2 μg kg⁻¹ soil. The method was successfully used to determine PAH in soil extracts.     

Liquid chromatography time-of-flight mass spectrometry following sorptive microextraction for the determination of fungicide residues in wine

This work evaluates the suitability of sorptive microextraction, using disposable silicone sorbents, and liquid chromatography time-of-flight mass spectrometry (LC-TOF-MS) for the determination of 15 fungicides in wine. Under optimized conditions, wine samples (10 mL) were diluted with the same volume of ultrapure water and poured in a glass vessel containing a magnetic stirrer and 4 g of sodium chloride. Extractions were performed at room temperature for 4 h, using an inexpensive silicone disk (12 μL volume) exposed directly to the sample. Thereafter, analytes were recovered with 0.2 mL of acetonitrile. The electrospray ionization (ESI) source was operated in the fast polarity switching mode obtaining, in the same injection, selective LC-MS records (extracted with a mass window of 10 ppm) of compounds rendering [M + H]⁺ and [M-H]⁻ ions. The method provided limits of quantification (LOQs) between 0.1 and 2.2 ng mL⁻¹, linear response ranges up to 500 ng mL⁻¹, relative recoveries from 75% to 117% and an inter-day variability below 15% for all analytes in red and white wine samples. The feasibility of in situ sample enrichment followed by delayed desorption and analysis is also assessed.     

Environmental monitoring of phenolic pollutants in water by cloud point extraction prior to micellar electrokinetic chromatography

Many aromatic compounds can be found in the environment as a result of anthropogenic activities and some of them are highly toxic. The need to determine low concentrations of pollutants requires analytical methods with high sensitivity, selectivity, and resolution for application to soil, sediment, water, and other environmental samples. Complex sample preparation involving analyte isolation and enrichment is generally necessary before the final analysis. The present paper outlines a novel, simple, low-cost, and environmentally friendly method for the simultaneous determination of p-nitrophenol (PNP), p-aminophenol (PAP), and hydroquinone (HQ) by micellar electrokinetic capillary chromatography after preconcentration by cloud point extraction. Enrichment factors of 180 to 200 were achieved. The limits of detection of the analytes for the preconcentration of 50-ml sample volume were 0.10 μg L⁻¹ for PNP, 0.20 μg L⁻¹ for PAP, and 0.16 μg L⁻¹ for HQ. The optimized procedure was applied to the determination of phenolic pollutants in natural waters from San Luis, Argentina. Figure Schematic representation of the cloud point extraction process.     

Ion-pair hollow-fiber liquid-phase microextraction of the quaternary ammonium surfactant dicocodimethylammonium chloride

A two-phase hollow-fiber (HF) liquid-phase microextraction (LPME) method was developed for determination of a quaternary ammonium compound surfactant, dicocodimethylammonium chloride, in aqueous samples. The porous HF was fixed on a metal rod support and was impregnated with approximately 6.6 μL of organic extractant, which was immobilized in the HF pores. Surfactant extraction was facilitated by addition of carboxylic acid to the sample forming neutral ion pairs with the quaternary ammonium compound. After extraction, the analyte was transferred from the organic extractant in the fiber pores by dissolving the 1-octanol into 100 μL methanol. The methanol extract was analyzed by liquid chromatography–mass spectrometry. The method was optimized (with optimized parameters in brackets) with regard to type of organic extractant (1-octanol), fiber length (2 cm), choice and concentration of anionic carrier (600 μg L⁻¹ octanoate), procedure of transfer to methanol (15-min sonication), sample volume (250 mL), extraction time (17 h), pH (10), and ionic strength (50 mM carbonate). Aspects influencing repeatability in LPME of (quaternary ammonium) surfactants are discussed. The enrichment factor achieved in 250-mL carbonate buffer was around 400. Due to matrix effects, the enrichment factors achieved when industrial process water was analyzed were 120 or about 30% of that in carbonate buffer. Detection limits of 0.3 μg L⁻¹ in carbonate buffer and 0.9 μg L⁻¹ in industrial process water were obtained. If the studied compound is seen as a model substance representing quaternary dialkylated dimethylated ammonium surfactants in general, the developed method may be applied to other quaternary ammonium surfactants.     

On-line solid-phase extraction and multisyringe flow injection analysis of Al(III) and Fe(III) in drinking water

A new analytical method was developed for on-line monitoring of residual coagulants (aluminium and iron salts) in potable water. The determination was based on a sequential procedure coupling an extraction/enrichment step of the analytes onto a modified resin and a spectrophotometric measurement of a surfactant-sensitized binary complex formed between eluted analytes and Chrome Azurol S. The optimization of the solid phase extraction was performed using factorial design and a Doehlert matrix considering six variables: sample percolation rate, sample metal concentration, flow-through sample volume (all three directly linked to the extraction step), elution flow rate, concentration and volume of eluent (all three directly linked to the elution step). A specific reagent was elaborated for sensitive and specific spectrophotometric determination of Al(III) and Fe(III), by optimizing surfactant and ligand concentrations and buffer composition. The whole procedure was automated by a multisyringe flow injection analysis (MSFIA) system. Detection limits of 4.9 and 5.6 μg L⁻¹ were obtained for Al(III) and Fe(III) determination , respectively, and the linear calibration graph up to 300 μg L⁻¹ (both for Al(III) and Fe(III)) was well adapted to the monitoring of drinking water quality. The system was successfully applied to the on-site determination of Al(III) and Fe(III) at the outlet of two water treatment units during two periods of the year (winter and summer conditions).     

Determination of biogenic amines in food by automated pre-column derivatization with 2-naphthyloxycarbonyl chloride (NOC-CI)

Summary The fluorogenic reagent 2-naphthyloxycarbonyl chloride (NOC-Cl) has been used for the automated precolumn derivatization of biogenic amines (BAs) at ambient followed by liquid-chromatographic separation of the derivatives formed. For optimized derivatization samples in 0.5 M borate buffer (pH 9.0) were derivatized with 5 mM NOC-Cl in acetonitrile (MeCN) for 3 minutes. Excess of reagent was scavenged by addition of 20 mM glycine in water. For HPLC a Superspher^? RP-18e column and gradient elution using 0.1 M sodium acetate buffer (pH 4.4) and MeCN were used. The NOC-derivatives were detected by fluorescence at an emission wavelength of 335 nm at an excitation wavelength of 274 nm. This method allows the detection of BAs (2-phenylethylamine, putrescine, histamine, cadaverine, tyramine, spermidine, spermine) found in food and beverages (fruit juices, wines, various vinegars, fermented cabbage juice, and salmon). Detection limit of BAs are approximately 49–113 μg kg⁻¹ with the exception of histamine (747 μg kg⁻¹) (injected amounts: 18–41 pg histamine 267 pg), at a signalto-noise ratio of 3:1. The limits of determination are approximately 82–189 μg kg⁻¹ (histamine 1245 μg kg⁻¹) at a signal-to-noise ratio of 5:1. The correlation coefficients of linearity are 0.9910–0.9976. Recoveries from different matrices range from 65 to 109%, depending on the sample investigated. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996.     

Development of a sequential injection anodic stripping voltammetry (SI-ASV) method for determination of Cd(II), Pb(II) and Cu(II) in wastewater samples from coatings industry

This paper describes the development and validation of a sequential injection (SI) anodic stripping voltammetry (ASV) method using the hanging mercury drop electrode for accumulation of the heavy metal cations Cu(II), Pb(II) and Cd(II). The method was applied to wastewater samples after proper acid digestion in open vessels to eliminate matrix effects. For a deposition time of 90 s at the flow rate of 10 μl s⁻¹, the detection limits of the method were 0.06, 0.09 and 0.16 μmol L⁻¹ for Cd, Pb and Cu, respectively. Under these conditions the linear dynamic range was between 0.20 and 9.0 μmol L⁻¹ and the sampling frequency was 30 analyses per hour. The relative standard deviation of the method was 3%(n=7) at the concentration level of 2.0 μmol L⁻¹. The accuracy of the method was evaluated by spiking the samples with known amounts of the metal cations, and by comparison with an independent analytical technique, the inductively coupled plasma atomic emission spectroscopy (ICP-AES). Average recoveries were around of 84%, and the results showed no evidence of systematic errors in comparison to the ICP-AES.