Evaluation of an atomic force microscopy pull-off method for measuring molecular weight and polydispersity of polymer brushes: effect of grafting density

The accuracy of the molecular weights Mn and polydispersities of polymer brushes, determined by stretching the grafted chains using atomic force microscopy (AFM) and measuring the contour length distribution, was evaluated as a function of grafting density sigma. Poly(N,N-dimethylacrylamide) brushes were prepared by surface initiated atom transfer radical polymerization on latex particles with sigma ranging between 0.17 and 0.0059 chains/nm2 and constant Mn. The polymer, which could be cleaved from the grafting surface by hydrolysis and characterized by gel permeation chromatography (GPC), had a Mn of 30,600 and polydispersity (PDI) of 1.35. The Mn determined by the AFM technique for the higher density brushes agreed quite well with the GPC results but was significantly underestimated for the lower sigma. At high grafting density in good solvent, the extended structure of the brush increases the probability of forming segment-tip contacts located at the chain end. When the distance between chains approached twice the radius of gyration of the polymer, the transition from brush to mushroom structure presumably enabled the formation of a larger number of segment-tip contacts having separations smaller than the contour length, which explains the discrepancy between the two methods at low sigma. The PDI was typically higher than that obtained by GPC, suggesting that sampling of chains with above average contour length occurs at a frequency that is greater than their spatial distribution.     

Attractive bridging interactions in dense polymer brushes in good solvent measured by atomic force microscopy

Using an atomic force microscope (AFM), we have investigated the interaction forces exerted by latex particles bearing densely grafted polymer brushes consisting of poly(N,N-dimethylacrylamide) (PDMA), poly(methoxyethylacrylamide) (PMEA), poly(N-isopropylacrylamide) (PNIPAM), and PMEA-b-PNIPAM in aqueous media (good solvent). The brushes were prepared by controlled surface-initiated atom transfer radical polymerization, and the hydrodynamic thicknesses were measured by dynamic light scattering. The molecular weight (Mn), grafting density (sigma), and polydispersity (PDI) of the brushes were determined by gel permeation chromatography and multiangle laser light scattering after cleaving the polymer from the latex surface by hydrolysis. Force profiles of PDMA (0.017 nm(-2) < or = sigma < or = 0.17 nm-2) and PMEA (sigma = 0.054 nm-2) brushes were purely repulsive upon compression, with forces increasing with Mn and a, as expected, due to excluded volume interactions. At a sufficiently low grafting density (sigma = 0.012 nm-2), PDMA exhibited a long-range exponentially increasing attractive force followed by repulsion upon further compression. The long-range attractive force is believed to be due to bridging between the free chain ends and the AFM tip. The PNIPAM brush exhibited a bridging force at a grafting density of 0.037 nm(-2), a value lower than the sigma needed to induce bridging in the PDMA brush. Bridging was therefore found to depend on grafting density as well as on the nature of the monomer. The grafting densities of these polymers were larger than those typically associated with bridging. Bridging interactions were used to confirm the presence of PNIPAM in a block copolymer PMEA-b-PNIPAMA brush given that the original PMEA homopolymer brush produced a purely repulsive force. The attractive force was first detected in the block copolymer brush at a separation that increased with the length of the PNIPAM block.     

Direct observation of the phase transition for a poly(N-isopropylacryamide) layer grafted onto a solid surface by AFM and QCM-D

The temperature-induced structural changes of a thermo-responsive poly(N-isopropylacrylamide) (PNIPAM) layer grafted onto a silica substrate were investigated in aqueous solution using an atomic force microscope (AFM) and a quartz crystal microbalance with dissipation (QCM-D). A PNIPAM layer was grafted onto the silicon wafer surface by free radical polymerization of NIPAM to obtain a high molecular weight polymer layer with low-grafting density overall. By AFM imaging, the transition of the grafted PNIPAM chains from a brush-like to a mushroom-like state was clearly visualized: The surface images of the plate were featureless at temperatures below the LCST commensurate with a brush-like layer, whereas above the LCST, a large number of domain structures with a characteristic size of approximately 100 nm were seen on the surface. Both frequency and dissipation data obtained using QCM-D showed a significant change at the LCST. Analysis of these data confirmed that the observed PNIPAM structural transition was caused by a collapse of the brush-like structure as a result of dehydration of the polymer chains.     

Self-assembly of catecholic macroinitiator on various substrates and surface-initiated polymerization

A catechol-containing macroinitiator has been designed for the surface-initiated atom transfer radical polymerization (SI-ATRP) from various substrates at ambient temperature. Temperature-sensitive poly(N-isopropyl acrylamide) (PNIPAM) brushes were successfully grafted from a range of substrates surfaces, including metals and polyimides, via SI-ATRP using the resulting macroinitiator, which were characterized by X-ray photoelectron spectroscopy (XPS), water contact angle measurements, and atomic force microscopy (AFM). Effects of the temperature response behavior of PNIPAM brushes on the water contact angles and the impedance of the modified surfaces were also exhibited. The self-assembled film of macroinitiator and the resulting polymer brushes were both stable to soaking of basic solvents, and the brushes did not show any exfoliation or delamination even after 2 h of ultrasonic test. The advantages of the macroinitiator in strong interactions with surfaces and high stability and convenience make it possible to modify the native materials with polymer brushes in a convenient and nondestructive way. Importantly, the macroinitiator is compatible with microcontact printing, and patterned polymer brushes on Ti plate were demonstrated by microcontact printing of BrDOPAMA and the following SI-ATRP.     

表面温敏聚合物刷的原子力显微镜和石英晶体微天平研究

通过表面引发的原子转移自由基聚合在硅片表面制备了聚（N-异丙基丙烯酰胺）（PNIPAAm）聚合物刷。用原子力显微镜（AFM）分别研究了PNIPAAm的接枝动力学、温度和溶剂性质对厚度的影响以及PNIPAAm链与原子力针尖间的粘附力。结果表明,PNIPAAm链在硅片表面的生长具有很好的可控性。常温下厚度为33nm的PNIPAAm膜在水溶液中的增加到82.4nm;而在甲醇/水（v/v,1:1）溶液中,PNIPAAm分子链处于坍塌收缩状态,厚度降低为45nm;在55℃下干燥所得厚度则仅为22nm。力-距离测量结果表明,在溶液中,PNIPAAm链与原子力针尖之间的粘附力远小于在干态下的粘附力。用石英晶体微天平（QCM-D）对PNIPAAm的可逆相转变进行了研究,结果表明PNIPAAm分子链随温度变化的构象转变是发生在30-34℃之间的连续过程。     

Conformation of poly(styrene sulfonate) layers physisorbed from high salt solution studied by force measurements on two different length scales

The conformation of poly(styrene sulfonate) (PSS) layers physisorbed from 1 M NaCl is determined by force measurements and imaging on two length scales. With colloidal probe technique steric forces as predicted for neutral grafted brushes are observed. On decrease and increase of the NaCl concentration, the grafting density remains constant, yet the brush thickness swells and shrinks reversibly with the salt concentration with an exponent of -0.3. At low salt conditions, the brush length amounts to 30% of the contour length, a behavior known for polyelectrolyte brushes and attributed to the entropy of the counterions trapped in the brush. Between a PSS layer and a pure colloidal silica sphere, the same steric forces are observed, and additionally at large separations (beyond the range of the steric repulsion) an electrostatic force is found. A negatively charged AFM tip penetrates the brush--a repulsive electrostatic force between the tip and surface is found, and single chains can be imaged. Thus, with the nanometer-sized AFM tip, the flatly adsorbed fraction of the PSS chains is seen, whereas the micrometer-sized colloidal probe interacts with the fraction of the chains penetrating into solution.     

Temperature-induced aggregation of poly(N-isopropylacrylamide)-stabilized CdS quantum dots in water

Water-soluble nanosized semiconductor CdS particles (quantum dots, QDs) were synthesized with a protective layer of covalently grafting linear thermally sensitive poly(N-isopropylacrylamide) chains. Reversible association and dissociation of these CdS particles can be induced via an alteration of the solution temperature. The formation and fragmentation of the QD aggregates of the CdS particles were systematically investigated by laser light scattering (LLS) and confirmed by transmission electron microscopy (TEM). There exists a hysteresis during one heating-and-cooling cycle. The CdS particles stabilized with shorter PNIPAM chains (Mn=15,000 g/mol) can associate to form larger and denser spherical aggregates with a much higher aggregation number than those grafted with longer PNIPAM chains (Mn=31,000 g/mol) in the heating process. The dissociation (fragmentation) in the cooling process has two stages: initially, the aggregates dissociate as the temperature decreases, and then, the fragmentation stops over a wider temperature range before complete dissociation. We attribute such a two-stage fragmentation to a balanced effect of inter- and intrachain hydrogen bonding as well as the hydrophobic interaction between PNIPAM chains and CdS particles.     

Thermoresponsive coatings strongly adhering to (semi)conducting surfaces

Thermoresponsive brushes have been efficiently grafted onto (semi)conductive surfaces by a two-step process. In the first step, poly(N-succinimidyl acrylate) chains have been chemisorbed onto silicon or stainless steel by the electrografting method. Then, these modified electrodes were immersed in isopropylamine in order to transform the grafted chains to the thermoresponsive poly(N-isopropyl acrylamide). The thermal response of these brushes has been shown by AFM. This straightforward grafting process is quite attractive for surface modification in confined media and is thus promising for microfludics application.     

Collapse and swelling of thermally sensitive poly(N-isopropylacrylamide) brushes monitored with a quartz crystal microbalance

Thermally sensitive poly(N-isopropylacrylamide) (PNIPAM) brushes grafted on SiO2-coated quartz crystal surface were prepared with a surface-immobilized initiator. Using quartz crystal microbalance (QCM), we investigated the collapse and swelling of the brushes in water in real time. Both frequency and dissipation of PNIPAM brushes were found to gradually change throughout a temperature range 20-38 degrees C, indicating that PNIPAM brushes undergo a continuous collapse transition in contrast with PNIPAM chains free in dilute solution exhibiting a sharp coil-to-globule transition. This result is in accordance with the previous theoretical prediction. The nonuniformity and stretching of PNIPAM brushes as well as the cooperativity between collapse and dehydration transitions are thought to be responsible for the continuity. On the other hand, a hysteresis was also observed in the cooling process. This is not only due to the intrachain and interchain interactions formed in the collapsed state but also to the nonuniform structure and stretching of the high-density brushes.     

Reentrant behavior of poly(N-isopropylacrylamide) brushes in water-methanol mixtures investigated with a quartz crystal microbalance

The solvent composition induced reentrant behavior of poly(N-isopropylacrylamide) (PNIPAM) chains grafted on a SiO2 surface in water-methanol mixtures was investigated using a quartz crystal microbalance with dissipation monitoring (QCM-D) at 20 degrees C. The frequency and energy dissipation responses showed that the grafted PNIPAM chains sharply collapse when the methanol content (x(m)) reaches approximately 17 mol %. In the range 17-50 mol %, the grafted chains remain in a collapsed state. Further increase of the methanol content leads to an abrupt reswelling of the collapsed chains at x(m) > approximately 50 mol %. The sharp reentrant swelling-to-collapse-to-swelling transition was attributed to the water-methanol complexation instead of the preferential adsorption effect. Our results also suggest that the water-methanol complexation is not induced by hydrophobic interaction but by hydrogen bonding.     

Controlled sub‐10‐nanometer poly(N‐isopropyl‐acrylamide) layers grafted from silicon by atom transfer radical polymerization

Surface‐initiated atom transfer radical polymerization (SI‐ATRP) was used to graft poly(N‐isopropylacrylamide) (PNIPAM) brush layers with a controllable thickness in the 10‐nm range from silicon substrates. The rate of polymerization of N‐isopropylacrylamide was tuned by the [Cu(II)]₀/[Cu(I)]₀ ratio between the deactivating and activating species. The polymer layer thickness was characterized by atomic force microscopy (AFM) and ellipsometry. PNIPAM layers with a dry thickness between 5.5 and 16 nm were obtained. Time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) confirmed that the chemical structure is PNIPAM brushes. Analysis of the AFM data showed that our procedure leads to polymer grafts in the “mushroom‐to‐brush” transition regime.     

Monte carlo simulations of polydisperse polymers grafted on spherical surfaces

This article presents effects of polydispersity in polymers grafted on spherical surfaces on grafted polymer chain conformations, grafted layer thickness, and free‐end monomer distribution within the grafted layer. At brush‐like grafting densities, as polydispersity index (PDI) increases, the scaling exponent of radius of gyration of grafted chains approaches that of a single chain grafted on the same nanoparticle, because polydispersity alleviates monomer crowding within the brush. At high PDI, the chains shorter than the number average chain length, N_n, have more compressed conformations, and the chains longer than N_n overall stretch less than in the monodisperse case. As seen in polydisperse flat brushes at high grafting densities, the grafted layer thickness on spherical nanoparticle increases with PDI. Polydispersity eliminates the region near the surface devoid of free‐end monomers seen in monodisperse cases, and it reduces the width of free‐end monomer distribution and shifts the free‐end monomer distribution close to the surface. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Nanoscale phase separation in mixed poly(tert-butyl acrylate)/polystyrene brushes on silica nanoparticles under equilibrium melt conditions

This communication reports on the study of microphase separation of well-defined mixed poly(tert-butyl acrylate) (PtBA)/polystyrene (PS) brushes on silica nanoparticles under equilibrium melt conditions. Mixed PtBA/PS brushes were synthesized from an asymmetric, difunctional initiator-terminated self-assembled monolayer by combining atom transfer radical polymerization and nitroxide-mediated radical polymerization. Two symmetric PtBA/PS mixed brush samples with different molecular weights were used in this study and were thermally annealed in vacuum at 150 degrees C. For the mixed brushes with number average molecular weights (Mn) of 24 200 g/mol for PtBA and 23 000 g/mol for PS, two glass transitions were observed in the differential scanning calorimetry analysis. Transmission electron microscopy study showed that the two grafted polymers underwent a lateral microphase separation, forming a random worm-like pattern with a feature size of approximately 10 nm on the silica particle surfaces. In contrast, the mixed brushes with a Mn of 10,400 g/mol for PtBA and 11,900 g/mol for PS did not microphase separate. Although the mixed brushes are on curved substrates, this work provides results consistent with the theoretical prediction that symmetric mixed homopolymer brushes undergo lateral rather than vertical phase separation under equilibrium melt conditions.     

Grafting of single, stimuli-responsive poly(ferrocenylsilane) polymer chains to gold surfaces

Redox-responsive poly(ferrocenylsilane) (PFS) polymer molecules were attached individually to gold surfaces for force spectroscopy experiments on the single molecule level. By grafting ethylenesulfide-functionalized PFS into the defects of preformed self-assembled monolayers (SAMs) of different omega-mercaptoalkanols on Au(111), the surface coverage of PFS macromolecules could be conveniently controlled. Atomic force microscopy (AFM), contact angle, as well as cyclic and differential pulse voltammetry measurements were carried out to characterize the morphology, wettability, and surface coverage of the grafted layers. The values of the PFS surface coverage were found to depend on the chain length of the omega-mercaptoalkanol molecules and on the concentration of the PFS solution but not on the insertion time or on the molar mass of PFS. The equilibrium surface coverages were successfully described by Langmuir adsorption isotherms. For low-surface coverage values (< 6.2 x 10(-4) chain/nm2), achieved by PFS insertion from very dilute solutions (8 x 10(-6) M) into long-chain SAMs, AFM and differential pulse voltammetry showed that surfaces exposing isolated individual polymer chains were obtained. The isolated PFS macromolecules were subjected to in situ AFM-based single molecule force spectroscopy (SMFS) measurements. The single chain elasticity of PFS in isopropanol (and ethanol) was fitted with the modified freely jointed chain (m-FJC) model. This procedure yielded a Kuhn segment length of 0.33 +/- 0.05 nm and a segment elasticity of 32 +/- 5 nN/nm.     

Macromolecular brushes synthesized by “grafting from” approach based on “click chemistry” and RAFT polymerization

Well‐defined macromolecular brushes with poly(N‐isopropyl acrylamide) (PNIPAM) side chains on random copolymer backbones were synthesized by “grafting from” approach based on click chemistry and reversible addition‐fragmentation chain transfer (RAFT) polymerization. To prepare macromolecular brushes, two linear random copolymers of 2‐(trimethylsilyloxy)ethyl methacrylate (HEMA‐TMS) and methyl methacrylate (MMA) (poly(MMA‐co‐HEMA‐TMS)) were synthesized by atom transfer radical polymerization and were subsequently derivated to azide‐containing polymers. Novel alkyne‐terminated RAFT chain transfer agent (CTA) was grafted to polymer backbones by copper‐catalyzed 1,3‐dipolar cycloaddition (azide‐alkyne click chemistry), and macro‐RAFT CTAs were obtained. PNIPAM side chains were prepared by RAFT polymerization. The macromolecular brushes have well‐defined structures, controlled molecular weights, and molecular weight distributions (M_w/M_n ≦ 1.23). The RAFT polymerization of NIPAM exhibited pseudo‐first‐order kinetics and a linear molecular weight dependence on monomer conversion, and no detectable termination was observed in the polymerization. The macromolecular brushes can self‐assemble into micelles in aqueous solution. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 443–453, 2010     

Thermoresponsive Polymer Brush Modulation on the Direction of Motion of Phoretically Driven Janus Micromotors

We report a thermoresponsive poly(N‐isopropylacrylamide) (PNIPAM) brush functionalized Janus Au–Pt bimetallic micromotor capable of modulating the direction of motion with the change of the ambient temperature. The PNIPAM@Au–Pt micromotor moved along the Au–Pt direction with a speed of 8.5 μm s^?1 in 1.5 % H₂O₂ at 25 °C (below the lower critical solution temperature (LCST) of PNIPAM), whereas it changed the direction of motion (i.e., along the Pt–Au direction) and the speed decreased to 2.3 μm s^?1 at 35 °C (above LCST). Below LCST, PNIPAM brushes grafted on the Au side were hydrophilic and swelled, which permitted the electron transfer and proton diffusion on the Au side, and thus the motion is regarded as a self‐electrophoretic mechanism. However, PNIPAM brushes above LCST became hydrophobic and collapsed, and thus the driving mechanism switched to the self‐diffusiophoresis like that of Pt‐modified Janus silica motors. These motors could reversibly change the direction of motion with the transition of the hydrophobic and hydrophilic states of the grafted PNIPAM brushes. Such a thermoresponsive polymer brush functionalization method provides a new strategy for engineering the kinematic behavior of phoretically driven micro/nanomotors.     

Preparation of End Grafted Polyacrylonitrile Brushes through Surface Confined Radical Chain Transfer Reaction

End grafted polyacrylonitrile (PAN) brush was prepared through surface initiated polymerization via the chain transfer process.The thiol-terminated monolayer and PAN brushes were characterized by FTIR,X-ray photoelectron spectroscopy(XPS),atomic force microscopy (AFM),ellipsometry and contact angle measurements etc.It is demonstrated that radical chain transfer reaction and surface initiated precipitate polymerization can used to prepare end-grafted polymer brushes.     

两亲性PS-b-PEG嵌段共聚物刷的合成及响应行为

利用原子转移自由基聚合(ATRP)和点击化学(Click)反应, 在硅基底上制备了聚苯乙烯-b-聚乙二醇(PS-b-PEG)两亲性嵌段共聚物刷. 首先, 利用ATRP方法在表面改性的硅片引发苯乙烯单体(St)的聚合, 得到PS-Br均聚刷, 然后通过叠氮化钠(NaN₃)将均聚刷末端功能化为PS-N₃, 再与炔基聚乙二醇甲醚(Alkynyl-PEG)发生Click反应, 得到PS-b-PEG嵌段共聚物刷. 通过X射线光电子能谱(XPS)和接触角测量仪表征了聚合物刷的表面化学组成和表面亲疏水性质, 证明在硅基底上接枝了嵌段共聚物刷. 用原子力显微镜(AFM)观察了PS-b-PEG嵌段共聚物刷在不同溶剂处理后的形态结构变化, 研究了其响应行为.     

Aggregation behaviour of peptide-polymer conjugates containing linear peptide backbones and multiple polymer side chains prepared by nitroxide-mediated radical polymerization

A series of peptides with an alternating sequence of alkoxyamine conjugated lysine and glycine residues were synthesized by classical solution phase peptide coupling. The resulting peptides containing up to eight alkoxyamine moieties were used as initiators in nitroxide-mediated polymerization (NMP) to obtain peptide-polymer conjugates with well defined linear peptide backbones and a defined number of polymeric side chains. Polymerization of styrene and N-isopropylacrylamide (NIPAM) occurred in a highly controlled fashion. Molecular weight and polydispersity index (PDI) were determined by gel permeation chromatography (GPC). Aggregation behaviour of these hybrid materials was investigated by dynamic light scattering (DLS) and atomic force microscopy (AFM). Depending on composition, number and length of the polymer side chains, the conjugates aggregate to different topologies. Whereas peptide-polystyrene conjugates may aggregate to so called honeycomb structures, peptide-poly-N-isopropylacrylamide conjugates show differentiated aggregation behaviour.     

Adsorption-desorption of Silica Nanoparticles on Poly(ethylene glycol) Brushes Grafted onto Au Substrate Studied by Quartz Crystal Microbalance

The adsorption-desorption of silica nanoparticles(NPs) on poly(ethylene glycol)(PEG) grafted onto gold(Au) substrate was studied by quartz crystal microbalance with dissipation monitoring(QCM-D) technique. The results of frequency and dissipation show that SiO₂ NPs can be adsorbed strongly on PEG-SH brushes at pH of 9.6, and a new dense and rigid construction is formed. Adjusting the pH from 9.6 to 12.3 resulted in the desorption of silica NPs from the PEG brushes because of a significant weakening of the hydrogen bond between the silica NPs and PEG chains. In addition, the viscoelastic properties of the system during the adsorption-desorption process were also analyzed via the relationship between the normalized frequency(Δf/n) and mass. And the corresponding atomic force microscopy(AFM) images also exhibit morphological changes during the above process, consistent with the changes in viscoelasticity.