Al2O3薄膜/纳米Ag颗粒复合结构的光吸收谱及增强Raman散射光谱研究

Al₂O₃介质薄膜与纳米Ag颗粒构成的复合结构,被应用于表面增强Raman散射探测实验中,其中Al₂O₃介质薄膜对纳米Ag颗粒的吸收谱及增强Raman散射光谱的影响被特别关注.该复合结构的光学特性表征出纳米Ag颗粒的偶极振荡特性.从光吸收谱中可以看到,其共振吸收谱随Al₂O₃介质薄膜厚度增加而在整个谱域上发生红移,表明纳米Ag颗粒的周围介电常数随Al₂O₃介质薄膜厚度的增加而增大.采用罗丹明6G作为探针原子,6个Raman特征峰的平均增益值作为表征表面增强Raman散射衬底增益程度的量度.实验结果表明,Al₂O₃介质薄膜层的引入提高了纳米Ag颗粒的衬底介电常数,并引起了散射共振的增强,从而使表面增强Raman散射强度提高.     

紫外波段SiO2/Si3N4介质膜分布式布拉格反射镜的制备与研究

采用光学传递矩阵方法设计了紫外波段SiO₂/Si₃N₄介质膜分布式布拉格反射镜, 并利用等离子体增强化学气相沉积技术在蓝宝石(0001)衬底上制备了SiO₂/Si₃N₄介质膜分布式布拉格反射镜. 光反射测试表明, 样品反射谱的峰值波长仅与理论模拟谱线相差10 nm, 并随着反射镜周期数的增加而蓝移. 由于SiO₂与Si₃N₄具有相对较大的折射率比, 因而制备的周期数为13的样品反射谱的峰值反射率就已大于99%. 样品反射谱的中心波长为333 nm, 谱峰的半高宽为58 nm. 样品截面的扫描电子显微镜和表面的原子力显微镜测量结果表明, 样品反射谱的中心波长蓝移是由子层的层厚和界面粗糙度的变化引起的. X射线反射谱表明,子层界面过渡层对于反射率的影响较小, 并且SiO₂膜的质量比Si₃N₄差, 也是造成反射率低于理论值的原因之一.     

硼(氮、氟)掺杂对TiO2纳米颗粒光学性能的影响

利用X射线衍射谱、拉曼光谱和紫外-可见光吸收光谱研究了硼(氮、氟)掺杂对TiO₂纳米颗粒光学性能的影响.X射线衍射谱和拉曼光谱结果表明,掺硼(氮、氟)对TiO₂纳米颗粒的锐钛矿相晶体结构无明显影响,而其锐钛矿晶格出现畸变(c/a值增大),这被归因于掺杂原子对TiO₂纳米颗粒表面氧原子缺位沿晶格c轴方向的占据.另外,掺硼(氮、氟)TiO₂纳米颗粒吸收带红移与TiO相似文献   

真空沉积法制备InSb纳米颗粒

采用真空沉积的方法在SiO₂基片上制备出了纳米InSb颗粒薄膜.利用原子力显微镜对4片样品表面进行分析,从其表面形貌图和三维图中可以观察到有粒径均匀的纳米InSb颗粒形成并且均匀地分布在SiO₂基片表面.实验表明,通过改变镀膜时间可以得到具有不同颗粒尺寸的InSb纳米颗粒,并且颗粒直径与沉积时间和厚度成正比.     

多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术，分别沉积Ti和Ti/Al膜，经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序，分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27     

Pr1-x Srx MnO3体系中O1s2p2p俄歇过程特性研究

对于组份为x=0.0和x=0.3的巨磁电阻锰氧化物Pr_1-x Sr_x MnO₃(PSMO)体系在OK阈值,Mn L_2,3边的区域内进行了O1s2p2p俄歇谱随光子能量变化的实验研究.实验结果显示O1s2p2p俄歇峰发生分裂并且可将其拟合为3个子峰.PSMO在OK阈值或Mn L_2,3边以下进行激发时,其俄歇峰3个子峰的相对强度基本保持恒定,然而反映终态效应特性的总强度却有起伏发生.这一状况在Mn L_2,3边以上激发时表现更为显著,即组份为x=0.3的总强度为x=0.0的4倍.对这些现象在共价键图     

过渡金属二硼化物的金属K边XAS研究

结合X射线衍射实验(XRD)和金属K边的X射线吸收谱(XAS)研究了过渡金属二硼化物(TiB₂,VB₂和CrB₂).在近边吸收区,除了主吸收峰之外,还观察到了3个弱的边前峰,它们是由于金属吸收原子的3d轨道在D6h配位场下分裂,分裂后的3个d轨道与高层金属原子4p轨道发生杂化而引起的.此外,还根据XRD实验得到的晶格参数初步拟合了金属K边EXAFS谱,得到了一些有意义的结果.     

纳米Ag颗粒表面等离子激元对上转换材料光致发光性能影响的研究

本文采用共烧结工艺将纳米Ag颗粒引入Yb³⁺, Er³⁺共掺的NaYF₄上转换材料中, 利用X射线衍射及扫描电子显微镜技术对制备的NaYF₄材料进行结构特性和表面形貌的表征, 通过吸收谱及荧光光谱测试技术对NaYF₄材料光吸收及光发射特性进行表征. 通过对纳米Ag颗粒引入量的优化, 获得了Yb³⁺, Er³⁺共掺的NaYF₄上转换材料荧光发射峰的增强, 300—800 nm全光谱范围内增益达28%, 在544 nm处获得最大增益55%, 具有显著的荧光增强效果. 同时分析了不同数量纳米Ag颗粒的引入对NaYF₄材料吸收谱及光致发光特性影响, 指出了表面等离子激元的光猝灭及共振吸收增强作用机理.     

一维缺陷光子晶体温度的测量

采用Si和SiO₂两种介质材料构造一维缺陷光子晶体，缺陷层介质为Si，利用传输矩阵法对带有缺陷的一维光子晶体的传光特性进行了理论分析，并得到其带隙特性.由于缺陷的存在，使得光子晶体的透射谱中产生缺陷峰.当被测温度变化时，根据两种介质的热光效应和热膨胀效应，光子晶体介质和缺陷层的光学厚度和折射率发生变化，透射谱缺陷峰产生漂移，由缺陷峰的中心波长漂移量得到被测温度的大小.构建了一维缺陷光子晶体测量温度的实验系统，实验结果表明缺陷峰中心波长与光子晶体所受的温度呈线性关系，测量灵敏度为0—2     

SiO2/Si衬底上石墨烯的制备与结构表征

在分子束外延(MBE)设备中,利用直接沉积C原子的方法在覆盖有SiO₂的Si衬底(SiO₂/Si)上生长石墨烯,并通过Raman光谱和近边X射线吸收精细结构谱等实验技术对不同衬底温度(500℃,600℃,700℃,900℃,1100℃,1200℃)生长的薄膜进行结构表征.实验结果表明,在衬底温度较低时生长的薄膜是无定形碳,在衬底温度高于700℃时薄膜具有石墨烯的特征,而且石墨烯的结晶质量随着衬底温度的升高而改善,但过高的衬底温度会使石墨烯质量降低.衬底温度为1100℃时结晶质量最好.衬底温度较低时C原子活性较低,难以形成有序的C-sp²六方环.而衬底温度过高时(1200℃),衬底表面部分SiO₂分解,C原子与表面的Si原子或者O原子结合而阻止石墨烯的形成,并产生表面缺陷导致石墨烯结晶变差.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.