Numerical analysis of a photonic crystal fiber based on two polarized modes for biosensing applications

This paper presents a theoretical study on a photonic crystal fiber plasmonic refractive index biosensor. The proposed photonic crystal fiber sensor introduces the concept of simultaneous detection with the linearly polarized and radially polarized modes because the sensing performance of the sensor based on both modes is relatively high, which will be useful for selecting the modes to make the detection accurately. The sharp single resonant peaks of the linearly polarized mode and radially polarized mode, are stronger and more sensitive to the variation of analyte refractive index than that of any other polarized mode in this kind of photonic crystal fiber. For linearly polarized mode and radially polarized mode, the maximum sensitivities of 10448.5nm per refractive index unit and 8230.7nm per refractive index unit can be obtained, as well as 949.8 and 791.4 for figure of merits in the sensing range of 1.33-1.45, respectively. Compared with the conventional Au-metalized surface plasmon resonance sensors, our device is better and can be applied as a biosensor.     

低功率近红外光的偏振方向对光致折射率变化影响的实验研究

研究了利用低功率近红外光辐照In:Fe:LiNbO3晶体时写入光束的偏振方向对光致折射率变化(Δn)的影响.分别采用正常偏振(o光)和非常偏振(e光)的近红外细激光束,在In:Fe:LiNbO3晶体中进行了光折变实验.研究表明,两种偏振方向引起晶体的Δn实测曲线相似,但变化规律恰好相反,o光引起的折射率变化量约是e光的3倍左右.近红外光写入下两种偏振光束引起晶体的Δn分布规律都不同于可见光,尤其是e光辐照区域中心晶体的折射率升高.因此,通过选择不同偏振方向的近红外光可以在光折变晶体中制作不同折射率分布的非线性光学器件.     

离子辅助沉积大口径传输反射镜面形控制研究

 针对大型激光系统中光束质量低和波前畸变等特点,采用离子辅助电子束蒸发技术成功实现对多层膜残余应力的精确控制。通过分析氧化铪、氧化硅单层膜残余应力变化规律,研究了离子源束压、束流参量对膜层折射率、残余应力性质及大小的影响。540 mm×340 mm×60 mm规格大口径传输反射镜面形PV值达到0.5λ(λ=632 nm),小光束损伤测试情况下,样品元件的损伤阈值大于30 J/cm2(N-on-1,1 064 nm,5 ns),利用该技术制备的大口径传输反射镜已获得成功应用。     

A tunable power splitter based on modes coupling and self-collimation effect in two-dimensional photonic crystals

A tunable power splitter is proposed in a two-dimensional photonic crystal with a line defect composed of two rows rods, whose refractive index can be controlled artificially. This device is working at a self-collimation frequency. The finite difference time domain (FDTD) simulations show that the beam splitting ratio is a function of the refractive index of line defect. If the index varies from 3.0 to 3.5, the beam intensity of one output port decreases from 87.2% (normalized by the input beam) to 0 while the intensity of the other output port increases from 8.98% to 100% monotonically. The coupling between the self-collimation mode and the defect mode is used to explain the working mechanism.     

阵列波导光栅解调系统光电集成中Si纳米线AWG的设计

设计了一种阵列波导光栅解调集成系统中的8通道Si纳米线阵列波导光栅波分复用器。根据材料的折射率设计了单模波导截面尺寸,利用光束传播法对所设计阵列波导光栅进行了模拟。结果表明,器件尺寸为200μm×219μm,远小于目前技术较成熟的硅基SiO2的尺寸,光功率分布符合高斯分布,信道间隔为1.8nm,串扰小于-21dB。对小尺寸AWG的设计具有参考意义。     

使线偏振光变为圆偏振光——薄膜1/4波片的设计

在一个折射率为N_2的基片上,镀制一层折射率为N_1=(N_0·N_2)~(12),厚度为d_1=λ/4(N_1~2-N_0~2Sin~2φ_0)~(-1/2)的透明介质薄膜,当一束波长为λ的线偏振光以特定的方位角α,在合适的入射角φ_0下,倾斜辐射到薄膜表面上时,可得到的反射光线为圆偏振光。     

光学马格努斯效应中的横向角移分析

从平面角谱理论出发,建立了光束在空气和玻璃界面折射的传输模型.基于这一模型,揭示了光学马格努斯效应中的横向角移现象.对于特定的线偏振和椭圆偏振光束,其折射场重心出现了横向角移,而当入射光束为圆偏振时,横向角移则会消失.在正负折射率界面,光束的横向角移产生了反转现象,这是由于光束在左手材料中发生了负衍射.超高折射率可明显地减少横向角移,而超低折射率则可显著地增强横向角移.这些发现将为如何调控和增强光学马格努斯效应提供理论依据. 关键词： 光学马格努斯效应 横向角移 圆偏振     

Electrically controlled waveguide mode in LC layer for fiber optic applications

A new electrically controlled waveguide mode for optical beams propagating in the plane of a liquid crystal (LC) layer is described. The mode is based on the total internal reflection of light beams from two parallel boundaries, which separates the regions of a liquid crystal cell with different director orientations and refractive indices. In experiments electric field was applied to the initially planar layer to produce the channel with a homeotropic orientation surrounded by the planar regions. It results in focusing and waveguide propagation of a light beam emitted by an optical fiber inserted in a liquid crystal cell. Scattering of light by thermal LC director fluctuations is used to visualize light beams propagation. The obtained waveguide mode can be used for an elaboration of electrically controlled LC switches with low operating voltages. The prototype of such device made with usage of a photolithography and a photo alignment technique is described. The possible ways of optimization of LC-switch are considered.     

MZ-MMI-based all-optical switch using nonlinear coupled waveguides

We propose an all-optical switch (AOS) based on Mach-Zehnder (MZ) and Multi-mode interference (MMI) using nonlinear closely coupled waveguides. The device operates by switching between two states of coupled waveguides. In first state the refractive index of waveguides are same and light field will completely couple to nonlinear waveguide in half length of coupler and will back in the second half. We will have π phase difference in this procedure and the input field will appear in Bar-state output. In the second state the refractive index of nonlinear waveguide increase with high intensity control field. In this case, we have lower coupling and change in phase. But, we choose the best refractive index change to obtain the phase change of multiple of 2π necessary for Cross-state in output. The beam propagation method is used to simulate the device operation.     

光擦除双光束耦合的阈值开关特性

基于光擦除折射率光栅和双光束耦合构成了一种新型的非线性光学器件.用带导模型和耦合波方程建立了理论公式.用KNSBN单晶和Ar~+激光进行了实验演示.理论和实验都表明该器件具有明显的阈值开关特性.     

Voltage-controlled transmission through a dielectric slab doped with quantum dot molecules

Transmission and reflection of an electromagnetic pulse through a dielectric slab doped with the quantum dot molecules are investigated. It is shown that the transmission and reflection coefficients depend on the inter-dot tunneling effect and can be simply controlled by applying a gate voltage without any changing in the refractive index or thickness of the slab. Such simple controlling prepares an active beam splitter which can be used in all optical switching, optical limiting, and other optical systems.     

Design of photonic bands for opal-based photonic crystals

To make a device from an opal—or otherwise—the photonic bands and the optical properties derived from them are needed. Knowing the effects of different parameters defining the opal geometry and different possible modifications of its structure are needed, too. An accurate definition of the device will be required to obtain a good performance. With this aim, the optics of light with a wavevector in the vicinity of the L point in the Brillouin zone and its coupling to bare opals band structure are presented. An important aspect is the transition from finite to infinite crystal and the study of size effects on the bands. It is possible to substantially alter the photonic band structure of an opal-based system, while maintaining the lattice structure, simply by growing layers of other materials with an appropriate refractive index. Here, it is shown how, by the growth of accurately controlled thin layers of silicon and germanium, and further processing, one can induce the opening of two complete photonic band gaps (PBGs) in an opal structure. Finally, the possibility to fabricate a simple device consisting in a planar waveguide will be shown. By means of a very simple and inexpensive procedure, engineered planar defects acting as microcavities have been realized. These can be viewed as a particular case of a much more general class of heterostructures that can be grown by combining opal vertical deposition and chemical vapour deposition of oxides. A further step is made by applying electron beam lithography to provide lateral definition and facilitate three-dimensional structuring.     

偶氮分散红聚合物薄膜的Z扫描研究

采用单光束Z扫描技术对新型光学存储材料偶氮分散红聚合物的薄膜样品进行了测量。实验结果表明 ,该样品的非线性折射率为负值。为消除非线性吸收的影响 ,将实验所得有孔Z扫描曲线除以开孔Z扫描曲线进行了处理。从Z扫描曲线的实验数据处理得到这种新型偶氮分散红聚合物薄膜材料的非线性折射率为 :- 5 .5× 10 -6cm2 /W ,其值比常见无机非线性光学材料大 8～ 9个数量级 ,是一种很有应用前景的新型光学存储材料。最后 ,对这种偶氮聚合物薄膜具有大的非线性折射率的物理机制进行了分析。初步认为 :在线偏振光照射下 ,偶氮分子变为各向异性。这些类似液晶相的分子很好地关联在一起 ,分子的取向对外界扰动的响应是一种集体的效果 ,所以他们具有很大的非线性响应。     

Effects of polarization on radiation absorption in one-dimensional semitransparent slab exposed to collimated irradiation

The internal distribution of radiative absorption in one-dimensional semitransparent slab exposed to collimated irradiation is determined by the ray tracing method, and the detailed computation formulae for the distribution of radiative absorption are deduced. It is found that the ray will be polarized by specular reflection of slab boundaries even if the collimated irradiation is unpolarized, and the extent of polarization increases with the internal reflection times. The effects of polarization on the radiative absorption are analyzed and the radiative absorption distributions are compared with those obtained from the case in which the effects of polarization are omitted. The results show that the large differences between reflectances of perpendicular and parallel polarized components are the main causes resulting in errors of radiative absorption distribution. The polarization of incident beam has significant influences on the radiative absorption. Even for an unpolarized beam irradiated near Brewster's angle, omitting the effects of polarization will result in large errors, and the errors increase with the refractive index.     

Total internal reflection prism in a laser cavity with polarized radiation

We have obtained the dependence of the reflectance of a right-angle roof prism on its refractive index and the azimuth angle for linearly polarized radiation incident on it. We have shown that using such a prism in the optical layout of a single-shot laser with an electro-optical element (EO) for a certain orientation makes it possible to substantially reduce the control voltage on the EO, compared with the conventional layout of a single-shot laser with an EO providing a beam path difference of λ/4.     

时域有限差分法数值仿真单光镊中微球受到的光阱力

本文采用三维时域有限差分法(FDTD)和Maxwell应力张量法建立了单光镊在焦点附近俘获球形微粒的光阱力模型,采用基于球矢量波函数(VSWF)的五阶高斯光源作为仿真光源,得到了准确的光场传播.讨论了光源的波长、束腰、偏振态和微球的半径、折射率对光阱力的影响,分析了在单光镊俘获微球时,邻近微球对光阱力的影响.特别研究了光源的偏振态对微球所受光阱力的作用效果,仿真结果表明圆偏振光比线偏振光对微球的俘获力更大;被光镊稳定俘获的微球,会受到邻近微球干扰,失去平衡状态,改变光源的偏振态可以改变微球的受力状态. 关键词： 光镊 光阱力 介质微球 时域有限差分法(FDTD)     

Analysis and optimization of an InGaAsP/InP waveguide variable optical attenuator

An InGaAsP/InP waveguide variable optical attenuator (VOA) is proposed in this paper. The device consists of straight input and output waveguides and an S-bend waveguide. An electrode is deposited on a portion of the waveguide to form an active region so that its refractive index can be modified by a current injection, resulting in the variation of the transmitted optical power. The beam propagation method is employed in the numerical simulation and the device structure is optimized using a genetic algorithm. The optimized VOA has a low excess loss (<1 dB) and a large dynamic range of about 40 dB.     

激光雷达系统快速准直的方法和光学装置

 研制了一种能够方便、快速调节激光雷达收发光路准直的光学装置,分析了装置楔角的选取要求、准直误差及其相应的矫正方法。该装置结构简单,主要由两个楔形光学平板组成,通过电机转动两个楔板可使出射光束方向在一定范围内任意改变,该调节范围由楔板的楔角和折射率决定。利用折射定律,严格推导了装置中两个楔形光学平板的旋转角度与出射光束方向之间的关系。提出了将该光学装置插入到激光雷达发射光路,采用螺旋式粗扫、圆形和径向细扫相结合的光束扫描方式实现对激光雷达准直的方法,并给出了系统准直调节过程中的判断准则和具体的准直步骤。     

折射率梯度引起反转的光自旋霍尔效应研究

从经典电动力学出发,研究了由折射率梯度导致的反转光自旋霍尔效应。通过分析光从光疏介质入射到光密介质和从光密介质入射到光疏介质两种情况,揭示了光自旋霍尔效应中的横移与偏振态、折射率梯度以及入射角等因素的定性关系。当入射角一定时,光从光疏介质入射到光密介质时的水平偏振横移绝对值大于垂直偏振横移,而从光密介质入射到光疏介质的情况正好与之相反,并且传输场的横移方向取决于折射率梯度方向,增大入射角能明显增强光自旋霍尔效应,对某一特定的线偏振光束,其左、右旋圆偏振光分量的横移等值反向。这些研究结果为调控光自旋霍尔效应提供了有效途径。     

Needle-based refractive index measurement using low-coherence interferometry

We present a novel needle-based device for the measurement of refractive index and scattering using low-coherence interferometry. Coupled to the sample arm of an optical coherence tomography system, the device detects the scattering response of, and optical path length through, a sample residing in a fixed-width channel. We report use of the device to make near-infrared measurements of tissues and materials with known optical properties. The device could be used to exploit the refractive index variations of tissue for medical and biological diagnostics accessible by needle insertion.