Separation and characterization of petroleum asphaltene fractions by ESI FT-ICR MS and UV-vis spectrometer

Using heptane, toluene, and tetrahydrofuran (THF) as eluant, asphaltenes were fractionated into five fractions based on their polarity and solubility. The molecular composition of polar heteroatom species in both asphaltene and its fractions were analyzed by negative-ion electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI FT-ICR MS). The application of UV-vis spectrometer in characterizing asphaltene composition and measuring asphaltene concentration was discussed. About 11.9 wt% asphaltene components adsorbed permanently on silica gel in the extrography column after excessive elution with various solvents. In negative FT-ICR MS, the mass spectra show that acidic and neutral nitrogen-containing compounds such as N1 and N1S1 mainly existe in the first three less polar fractions, while oxygen-containing compounds such as O2 , O2S, O2S2 , O3 , and O4 show high relative abundance in more polar fractions. These results suggest oxygen-containing compounds have stronger adsorption ability with silica gel. It was observed that the double bond equivalence (DBE) distribution of N1 class species in the fractions shifted to higher values while the carbon number shifted to smaller numbers as polarity of fractions increased. This indicates that acidic and neutral N1 compounds with longer carbon chain and less aromaticity have less polarity compared with those with shorter carbon chain and stronger aromaticity. UV-vis absorbance indicats that fractions containing the most aromatic and most polar asphaltene have better absorbance at long wavelength, while the fractions that consist of least aromatic and least polar asphatlenes show high absorbance at short wavelength.     

Estimating molecular masses of petroleum-derived fractions: High mass (>2000 u) materials in maltenes and asphaltenes from Maya crude oil

Molecular mass ranges and average masses of fractions from a heavy Mexican crude oil (Maya) have been studied, using mainly size exclusion chromatography (SEC) and laser desorption-mass spectrometry (LD-MS). Method development focused on the use of planar chromatography and size exclusion chromatography (SEC), to isolate narrow bands of material from solubility-separated fractions of the crude oil. The procedure provides a planar chromatography based method for studying mass ranges in complex hydrocarbon mixtures. It allows the calculation of ‘best estimate’ values for number and mass-averages. These can then be used in average structural parameter (ASP) calculations, for studying structural features of the samples. The method is applicable to both coal and petroleum-derived samples. The molecular mass estimates arrived at in this work for petroleum-derived samples are considerably higher than those reported by other workers for similar samples. The results presented here provide strong evidence for the presence of ions approaching m/z 10,000 in the Maya asphaltene. The maltene fraction was found to contain a small amount of ions with mass (m/z) in excess of 2000.     

三磷酸腺苷的电喷雾质谱裂解规律研究

采用电喷雾离子阱质谱仪对正负离子模式下5'-三磷酸腺苷(adenosine 5'-triphosphate,ATP)的各种离子[ATP+H]+、[ATP-nH+(n+1)Na]+(n=0～4)、[ATP-H]-的裂解规律进行了系统研究,并提出可能的裂解过程.实验发现在裂解过程中,ATP脱去γ-磷酸时,不仅是P-O键断裂,还存在三磷酸链上β-P＝O中O先夺去碱基上的氨基或核糖环上的羟基中H、N或O再亲核进攻磷引发结构重排,脱去γ-磷酸得到一系列碎片离子.利用理论计算解释了2种重排途径的可能性与碎片离子的丰度差异.     

Identification of the individual molecular species of ceramides derived from human erythrocytes using HPLC/MS and HPLC/MS/MS

A preparative separation of total ceramide fraction from the crude extract of the erythrocytary lipids was done by means of normal-phase column chromatography. This was followed by comprehensive profiling of the molecular species in the obtained ceramide by means of HPLC/MS and HPLC/MS/MS. The MS/MS analysis displayed that human erythrocytes contain 19 molecular species of the ceramide of which 12 can be unambiguously identified; erythrocytary ceramides may contain not only sphingosine but also sphinganine as their building blocks; one of the species (namely Cer 24:2/S18) previously has managed to escape identification. We also obtained a quantitative profile of major ceramide species showing the prevalence of Cer 22:0/S18, 24:0/S18 and 24:1/S18.     

Branching pattern and sequence analysis of underivatized oligosaccharides by combined MS/MS of singly and doubly charged molecular ions in negative-ion electrospray mass spectrometry

We previously reported that sequence and partial linkage information, including chain and blood-group types, of reducing oligosaccharides can be obtained from negative-ion electrospray CID MS/MS on a quadrupole-orthogonal time-of-flight instrument with high sensitivity and without derivatization (Chai, W.; Piskarev, V.; Lawson, A. M. Anal. Chem. 2001, 73, 651-657). In contrast to oligonucleotides and peptides, oligosaccharides can form branched structures that result in a greater degree of structural complexity. In the present work we apply negative-ion electrospray CID MS/MS to core-branching pattern analysis using nine 3,6-branched and variously fucosylated oligosaccharides based on hexasaccharide backbones LNH/LNnH as examples. The important features of the method are the combined use of CID MS/MS of singly and doubly charged molecular ions of underivatized oligosaccharides to deduce the branching pattern and to assign the structural details of each of the 3- and 6-branches. These spectra give complimentary structural information. In the spectra of [M - H]-, fragment ions from the 6-linked branch are dominant and those from the 3-linked branch are absent, while fragment ions from both branches occur in the spectra of [M - 2H]2-. This allows the distinction of fragment ions derived from either the 3- or 6-branches. In addition, a unique D2beta-3 ion, arising from double D-type cleavage at the 3-linked glycosidic bond of the branched Gal core residue, provides direct evidence of the branching pattern with sequence and partial linkage information being derived from C- and A-type fragmentations, respectively.     

IR与ESI/MS结合鉴定复杂表面活性剂结构

复杂表面活性剂的结构鉴定往往是比较困难的，尤其在有许多副产物共存时，尝试应用红外光谱、质谱以及电喷雾质谱相结合的方法鉴定复杂表面活性剂及其副产物的结构。     

Synthesis and characterization by MALDI-TOF MS of polycyclic siloxanes derived from p-substituted novolac resins by MALDI-TOF MS

Novel polycyclic siloxane resins were prepared from phenol-formaldehyde novolac type resins by reacting them with dialkyl or diaryl dichlorosilanes under anhydrous and high dilution conditions. The formation of polycyclic species was confirmed by the detection of absolute masses by MALDI-TOF mass spectrometry. ¹H- and ²⁹Si-NMR confirmed the substitutions of phenolic hydroxy groups by siloxane bonds. Curing studies were conducted on the polycyclic siloxane resins as well as on the polycyclic siloxane resins incorporated into two types of polysiloxane gums. A trace amount of potassium hydroxide was used as a catalyst for the crosslinking of these systems. The blend of polysiloxane with 30 wt % polycyclic siloxane was found to be stable at the curing temperature. Differential scanning calorimetry and thermogravimetric analysis techniques were used to study the thermal profiles of these systems. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2429–2437, 1998     

Potential inhibitors of chemokine function: Analysis of noncovalent complexes of cc chemokine and small polyanionic molecules by ESI FT-ICR mass spectrometry

Chemokines play a critical role in inducing chemotaxis, extravasation, and activation of leukocytes both in routine immunosurveillance and autoimmune diseases. Traditionally, to disrupt chemokine function, strategies have focused on blockage of its interaction with the receptor. Recently, it has been demonstrated that binding to glycosaminoglycans (GAGs) is also required for the in vivo activity of many chemokines. Thus, interference with the GAG-binding of chemokines may offer an alternative, valid, anti-inflammatory strategy. However, the potential of using small polyanions to inhibit the interactions between chemokines and cell surface GAGs has not been fully explored. In this study, a mass spectrometry based filtration trapping assay was utilized to study the interactions between two CCR 2 ligands (MCP-1/CCL2 and MCP-3/CCL7) and a series of low molecular weight, polyanionic molecules. Findings were confirmed by using a hydrophobic trapping assay. The results indicated that Arixtra (fondaparinux sodium), sucrose octasulfate, and suramin were specific binders of the chemokines, while cyclodextrin sulfate, although the most highly sulfated molecule among the ones investigated, showed no binding. The binding stoichiometry of the small molecule ligand was determined from the measured molecular weight of the noncovalent complex. Furthermore, the dissociation constant between MCP-3 and Arixtra was determined by using electrospray ionization Fourier transform ion cyclotron resonance (ESI FT-ICR) mass spectrometry, which compared favorably with the result of the isothermal titration calorimetry (ITC) assay. The relative binding affinity of these ligands to MCP-3 was also determined using a competitive filtration trapping assay.     

Numerical analysis of the influence of experimental conditions on the accuracy of dielectric parameters derived from electrorotation measurements

Two approaches were used to analyze the accuracy with which the dielectric properties of a particle may be deduced from experimental electrorotation (ROT) data. Firstly, the dependence of ROT spectra on individual dielectric parameters was assessed by a sensitivity analysis. Secondly, simulated rotational spectra were used to investigate the effects of typical experimental errors on the confidence levels with which dielectric parameters can be derived from ROT data by parameter optimization procedures. The focus was on the single-shell, spherical dielectric model most widely applied for analyzing cellular dielectric properties, but the methods are applicable to any model. The following conclusions were drawn: (1) ROT spectra show different sensitivities to different parameters, resulting in different accuracy levels when these parameters are derived by optimization; (2) each rotation peak in a ROT spectrum can only be used to determine uniquely two parameters; (3) unless the experimental field strength and frictional forces are precisely known, the scaling factor in the ROT spectrum should not be fixed; instead, the ROT optimization should either be constrained by additional experimental information or determination of the membrane conductance should be sacrificed; (4) experimental conditions should be chosen carefully to maximize the sensitivity of the ROT spectrum to the parameters of interest; (5) ROT spectra should be taken to as high a frequency as possible to allow accurate determinations of interior parameters; (6) the analysis techniques used here can be applied to other models and experimental conditions in order to substantiate the accuracy level of parameters in other applications.     

Effects of vacuum pyrolysis conditions on the characteristics of activated carbons derived from pistachio-nut shells

Preparation of effective adsorbents from pistachio-nut shells was carried out. Optimization of the vacuum pyrolysis parameters prior to activation was carried out to study the effects of vacuum pyrolysis temperature, hold time, and heating rate on the properties of chars and activated carbons, while CO2 activation conditions were fixed at a temperature of 900 degrees C, an activation time of 30 min, a heating rate of 10 degrees C/min, a CO2 flow rate of 100 cm3/min, and a nitrogen flow rate of 150 cm3/min. The optimum vacuum pyrolysis conditions for preparing activated carbons with high surface area and pore volume were identified. The microstructure and microcrystallinity of the activated carbons prepared were examined by scanning electron microscopy and powder X-ray diffraction techniques respectively while the Fourier transform infrared spectra determined any changes in the surface functional groups produced during different preparation stages. Experimental results show that it is feasible to prepare activated carbons with high BET surface area from pistachio-nut shells.     

Quantification and identification of bioactive metabolites from Kalopanacis Cortex by HPLC with evaporative light scattering detection and ESI quadrupole TOF MS

A method based on HPLC coupled with an evaporative light scattering detection and ESI quadrupole TOF MS was established for the quantification and identification of phenolics and triterpene saponins in Kalopanacis Cortex using a gradient elution of acetonitrile with 0.1% formic acid and water with 0.1% formic acid on an RP C₁₈ column (4.6 × 250 mm, 5 μm). Diverse validation parameters, such as the linearity, LOD and LOQ, accuracy, precision, repeatability, and stability, were successfully obtained. Additionally, the efficiencies of different extraction methods were compared. The developed method was applied for the quantitative analysis of twelve representative metabolites in 61 Kalopanacis Cortex samples. The quantitation results showed that coniferin, kalopanaxsaponin C, septemlosides II, III, C, and D exhibited distinct regional patterns in Kalopanacis Cortex samples. These six compounds including one new triterpene saponin show potential as marker compounds for evaluating the quality of Kalopanacis Cortex and the geographical variation in its chemical composition.     

Structural characterization of the GM1 ganglioside by infrared multiphoton dissociation, electron capture dissociation, and electron detachment dissociation electrospray ionization FT-ICR MS/MS

Gangliosides play important biological roles and structural characterization of both the carbohydrate and the lipid moieties is important. The FT-ICR MS/MS techniques of electron capture dissociation (ECD), electron detachment dissociation (EDD), and infrared multiphoton dissociation (IRMPD) provide extensive fragmentation of the protonated and deprotonated GM1 ganglioside. ECD provides extensive structural information, including identification of both halves of the ceramide and cleavage of the acetyl moiety of the N-acetylated sugars. IRMPD provides similar glycan fragmentation but no cleavage of the acetyl moiety. Cleavage between the fatty acid and the long-chain base of the ceramide moiety is seen in negative-ion IRMPD but not in positive-ion IRMPD of GM1. Furthermore, this extent of fragmentation requires a range of laser powers, whereas all information is available from a single ECD experiment. However, stepwise fragmentation by IRMPD may be used to map the relative labilities for a series of cleavages. EDD provides the alternative of electron-induced fragmentation for negative ions with extensive fragmentation, but suffers from low efficiency as well as complication of data analysis by frequent loss of hydrogen atoms. We also show that analysis of MS/MS data for glycolipids is greatly simplified by classification of product ion masses to specific regions of the ganglioside based solely on mass defect graphical analysis.     

Hydrothermal liquefaction of cypress: Effects of reaction conditions on 5-lump distribution and composition

Effects of reaction temperature, reaction time and water amount on the hydrothermal liquefaction of cypress, were studied in this paper. The reaction system was divided into gas lump, water-soluble oil lump, heavy oil lump, volatile organic compounds lump, and solid residue lump. Results showed that temperature was the critical parameter for 5-lump distribution in the cypress hydrothermal conversion process. The higher temperature and longer reaction time were not usually suitable for the production of bio-oil (water-soluble oil and heavy oil). The increase in the yields of gas and volatile organic compounds was also observed as temperature was increased. However, the yield of the volatile organic compounds increased first, and then decreased with the reaction time and the water amount. High amount of water led to high conversion and bio-oil yield. The FT-IR analysis of the solid residues showed that the major peaks of cypress diminished after 280 °C. The GC–MS analysis showed that the volatile organic compounds, water-soluble oil and heavy oil comprised a mixture of organic compounds of 5–7, 5–10 and 7–26 carbons, respectively, which mainly included furfural, phenol, acids, furans and their derivatives. The WSO had similar elemental compositions but the HO had a higher content of carbon and a lower concentration of oxygen as compared to cypress.     

Effects of activation conditions on the structural and adsorption characteristics of pinecones derived activated carbons

This study was conducted to understand and optimize the activation process for the production of a low-cost activated carbon (AC) using a renewable and plentiful biomass waste, pinecones. This was achieved by tracking the changes in porous structure, surface chemistry and adsorption properties of the AC produced using different activating agents, activation temperatures, holding times and heating rates. Generally, produced ACs were predominantly microporous with small external surface area and were different in terms of H/C and O/C ratios. Study of Pb²⁺ cations adsorption on these samples proved the high affinity of the pinecones derived ACs to this cation. The best adsorption behaviour was recognized in sample prepared by impregnation with H₃PO₄ at weight ratio of 2, then heating at 400?°C for 2?h at 5?°C/min heating rate. This sample possessed the highest BET surface area (1335 m²/g). The adsorption process obeyed the pseudo-first-order and Freundlich model slightly better than the pseudo-second-order kinetics and Langmuir model. The high Langmuir maximum adsorption capacity of 418?mg/g supports the applicability of the produced AC for the removal of Pb²⁺ cations from wastewater.     

Effects of different extraction methods and conditions on the phenolic composition of mate tea extracts

A simple and rapid HPLC method for determination of chlorogenic acid (5-O-caffeoylquinic acid) in mate tea extracts was developed and validated. The chromatography used isocratic elution with a mobile phase of aqueous 1.5% acetic acid-methanol (85:15, v/v). The flow rate was 0.8 mL/min and detection by UV at 325 nm. The method showed good selectivity, accuracy, repeatability and robustness, with detection limit of 0.26 mg/L and recovery of 97.76%. The developed method was applied for the determination of chlorogenic acid in mate tea extracts obtained by ethanol extraction and liquid carbon dioxide extraction with ethanol as co-solvent. Different ethanol concentrations were used (40, 50 and 60%, v/v) and liquid CO? extraction was performed at different pressures (50 and 100 bar) and constant temperature (27 ± 1 °C). Significant influence of extraction methods, conditions and solvent polarity on chlorogenic acid content, antioxidant activity and total phenolic and flavonoid content of mate tea extracts was established. The most efficient extraction solvent was liquid CO? with aqueous ethanol (40%) as co-solvent using an extraction pressure of 100 bar.