激光入射角对靶面方向超热电子发射的影响

实验研究了超短超强激光脉冲与薄膜靶相互作用中产生的超热电子角分布随激光入射角的变化.在靶面方向观测到一束方向性很好的高能超热电子.该高能超热电子束的电子数目随着激光入射角的增大而增大.对结果的分析表明，表面准静态磁场是导致表面电子产生的主要原因. 关键词： 超热电子 表面准静态磁场 超强激光脉冲与等离子体相互作用     

利用飞秒激光等离子体产生的超热电子进行衍射实验的可行性研究

利用高强度超短脉冲激光与铝靶相互作用可以产生高能超热电子,这些超热电子入射到铝单晶上时将发生衍射.对高强度超短脉冲激光产生的超热电子与晶体的相互作用产生衍射及利用这样的衍射进行晶体结构分析的可行性进行了探讨 关键词： 等离子体 超热电子 衍射 晶体     

超短脉冲激光与乙醇微滴相互作用中超热电子的双叶状角分布

测量了聚焦光强为1016W/cm2的超短脉冲激光与乙醇微滴相互作用中产生的能量大于50?keV的超热电子的角分布和电子能谱.观察到的超热电子角分布明显依赖于激光的偏振特性，在与激光偏振平面平行的平面上超热电子相对于激光入射方向呈对称的双叶状分布.超热电子的能谱显示超热电子的最大能量大于750?keV.以上超热电子的角分布可用一个基于共振吸收机制的模型加以解释. 关键词： 超短脉冲激光 超热电子 微滴 共振吸收     

强激光与柱腔靶作用下准直高能电子束的产生

利用二维PIC粒子模拟程序研究了超短超强激光脉冲与柱腔靶相互作用产生的表面超热电子加速现象。采用光强为1021 W/cm2量级的超高斯激光脉冲掠入射进入柱腔靶,在靶的内壁上观察到了GeV量级的表面超热电子。超热电子束被准静态的电场和磁场约束在内壁表面附近,保证了电子束的准直性,发散角仅为1.6°;并且由于超热电子束在纵向激光电场中加速了mm级的距离,激光到高能电子(100 MeV)的转换效率达到了26.6%。另外,通过多参数模拟和理论解析讨论了激光的光强以及横向空间分布对这种表面超热电子加速的影响。     

近相对论强度激光与薄膜靶相互作用中靶厚度对超热电子发射方向的影响

研究了近相对论强度的激光脉冲与薄膜靶相互作用中，靶厚度对超热电子发射方向的影响.实验发现，随着靶厚度的增加，靶后超热电子的发射方向向靶的法线方向移动，同时电子束的发散角变大.结果分析表明，靶背面电荷分离场强度的变化是影响电子发射方向的主要原因. 关键词： 飞秒激光脉冲 超热电子 靶厚度     

超热电子的产生与定向发射

在超短超强激光与等离子体相互作用的过程中，等离子体中的一部分电子通过各种机制吸收能量转变成为高能的超热电子．它们不仅是惯性约束核聚变“快点火”过程中的能量载体，对激光脉冲在等离子体中的传输、能量沉积、转化等一系列过程也都发挥着重要的作用．文章对超短超强激光与等离子体相互作用过程中超热电子产生的主要物理机制以及影响超热电子定向发射的因素进行了介绍．     

超短超强激光与液体的相互作用研究

超短超强激光与液体靶相互作用时表现出许多有趣的特点，这明显区别于激光脉冲与固体或气体靶的相互作用情况．文章分别介绍了激光诱发等离子体所产生的高压冲击波、激光空泡、X射线、高能超热电子以及白光，对它们的产生机制及其各自的显著特征进行了综合描述．文章最后对超短超强激光脉冲与各种不同形态的液体靶相互作用的应用前景作了简单介绍。     

飞秒激光驱动X射线源中超热电子与靶相互作用研究

飞秒激光与靶相互作用产生超热电子,随后超热电子与靶原子碰撞,通过kα、kβ等散射过程,可辐射高亮度、飞秒级X射线,在原子与分子物理、生物及医学等领域均有广泛的应用前景.论文首先对飞秒激光驱动X射线源的发展进行简要叙述,然后对X射线源中的超热电子与靶相互作用进行研究.超热电子的产生由靶材对光脉冲的非碰撞吸收机制决定,X射线的产生由超热电子决定.研究超热电子、靶参数对X射线产额的影响,确定最佳参数值,可指导驱动激光脉冲参数的选择,以获得更大的X射线光子产额.使用蒙特卡洛模拟方法可研究超热电子动能及入射角、靶材(Cu靶)厚度对靶材上、下表面X射线辐射光子产额的影响,分析确定最佳超热电子动能及最佳靶厚.驱动激光强度与超热电子动能的定标关系表明：需要合理选择驱动激光参数,使真空加热机制主导超热电子产生过程,以在合适的激光脉冲强度下获得最大X射线光子产额.     

超热电子角分布和能谱的实验研究

对超短超强脉冲激光与固体薄膜靶相互作用产生的超热电子的空间分布和能谱特性进行了研究. 结果表明，超热电子的角分布和能谱均表现出各向异性. 分析认为这主要与超热电子产生的机制有关. 能谱的各向异性解释了目前各研究小组在相同的激光功率密度下，得到的超热电子温度却有很大差别的现象. 关键词： 飞秒激光 等离子体 能谱 角分布 各向异性     

不同偏振态下的飞秒激光脉冲与铝靶相互作用中超热电子的产生

研究了P偏振、S偏振和圆(C)偏振态下亚相对论强度飞秒激光脉冲与铝靶相互作用时产生的超热电子的能谱和靶背向角分布，并对S偏振产生的超热电子的特殊角分布通过引入表面磁场的概念进行了定性解释. 关键词： 超短超强激光 等离子体 超热电子 表面磁场     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.