The Properties of Polymer-Containing BeO Dispersions in an Acetone–Chloroform Binary Medium

The properties of Newtonian and concentrated (non-Newtonian) BeO dispersions in solutions of acidic poly(vinyl acetate-co-vinyl chloride) in binary mixtures of chloroform (a Lewis acid) and acetone (a Lewis base) of different compositions were studied. In contrast to systems characterized by strong acid–base interactions at the particle–medium interface, the role of the steric stabilization factor was found to be extremely low in the studied dispersions. Polymer-containing BeO dispersions in acetone had the highest kinetic stability due to the specific interactions of this solvent with BeO particles and polymer macromolecules contributing to the redispersion of particles and the formation of protective solvation shells. The obtained data on the effect of the dispersion medium composition on the rheological properties of concentrated BeO dispersions can be used for the selection of optimal regimes for preparation of pastes for high-temperature ceramics.     

Preparation of Colloidal Transition Metals in Polymers by Reduction with Alcohols or Ethers

Colloidal dispersions of rhodium, palladium, osmium, iridium, and platinum are prepared by refluxing the methanol-water solutions of rhodium(III) chloride, palladium(II) chloride, osmium(VIII) oxide, sodium chloroiridate, and chloroplatinic acid, respectively, in the presence of poly(vinyl alcohol) as a protective colloid. The preparations of colloidal dispersions of rhodium are successful in the presence of vinyl polymer with polar group such as poly(vinyl alcohol), polyvinylpyrrolidone, or poly(methyl vinyl ether). Polyethyleneimine, gelatin, polyethylene glycol), and dextran are ineffective as the protective colloid. Water-soluble primary alcohols such as methanol and ethanol, water-soluble secondary alcohols such as 2-propanol, and water-soluble diethers such as 1,4-dioxane are available as reductants for preparation of the colloidal dispersion of rhodium. The average diameters of metal particles in the colloidal dispersions of palladium, rhodium, platinum, iridium, and osmium in poly(vinyl alcohol) are determined by electron microscopy to be 53, 40, 27, 14, and < 10 Å, respectively. The particle size distribution in each colloidal dispersion is sharp within 50 Å wide. The particles in the colloidal dispersions of both iridium and osmium are highly dispersed with no aggregation, while in the colloidal dispersions of rhodium, palladium, and platinum, there exist aggregates of 5-15, 5-30, and 100-200 particles, respectively. Colloidal dispersions of rhodium, palladium, osmium, and platinum are effective as catalysts for hydrogenation of cyclohexene at 30.0°C under atmospheric hydrogen pressure.     

分散聚合水基聚苯胺乳胶微球制备与表征

水溶性空间稳定剂聚乙烯吡咯烷酮（PVP）存在时，采用分散聚合制备水溶性单分散的聚苯胺(PAn)乳胶粒子，采用透射电子显微镜（TEM）观察粒子形态及尺寸；利用紫外-可见吸收光谱对胶体分散体系进行表征.实验结果表明，当PAn含量较少（w< 16.78％）时， PAn-PVP复合乳胶粒子呈米粒状；当PAn含量较大（w >23.22％）时， PAn-PVP复合乳胶粒子呈球形.     

pH- and thermosensitive polyaniline colloidal particles prepared by enzymatic polymerization

Polyaniline colloids were prepared by enzymatic polymerization using chitosan and poly(N-isopropylacrylamide) as steric stabilizers. The resulting nanoparticles undergo flocculation by changing the pH or temperature of the aqueous dispersions. The environmentally responsive behavior of these colloids contrasts with that of polyaniline colloids synthesized using poly(vinyl alcohol) as the steric stabilizer. The colloid size was a function of the steric stabilizers and ranged from approximately 50 nm for polyaniline particles prepared in the presence of chitosan and partially hydrolyzed poly(vinyl alcohol) up to 350 nm for the particles synthesized using poly(N-isopropylacrylamide). UV-visible and Fourier transform infrared spectroscopic studies indicate that polyaniline colloids are spectroscopically similar to those obtained by traditional dispersion polymerization of aniline by chemical oxidation. These polyaniline colloids have potential applications in thermochromic windows and smart fluids.     

Assessment of polymeric flocculants in oily water systems

Oil-in-water emulsions are usually formed during oil production and treatment. Before being discarded, such dispersions should be treated. In order to improve the oil–water separation process using physical processes (decantation, flotation, centrifugation, etc.) the particle size of the disperse phase should be increased. This may be achieved through flocculation, which consists in the agglomeration of various particles or drops, using, as flocculating agents, high molecular weight hydrophilic macromolecules. A few studies have been carried out on the flocculation of finely divided oil drops in brine with the aid of generally ionic polyelectrolytes. This work shows the results obtained using nonionic polymers as flocculants. Commercial samples of poly(ethylene oxide-b-propylene oxide) and poly(vinyl alcohol) were evaluated through flocculation–flotation tests as well as the drop size distribution. The performance of such additives as flocculants for oil–water dispersions is related to their structure, composition, molecular weight and hydrophilic–lipophilic balance. The composition of the produced water is also an important parameter when choosing the features of the flocculant additive.     

Preparation and characterisation of polypyrrole colloids in non-aqueous media

We have prepared polypyrrole both as a bulk powder and as a sterically stabilised colloidal dispersion in a noved non-aqueous solvent, 2-merhoxyethanol. The steric stabiliser utilised in the latter system was a poly(vinyl acetate) homopolymer. The electroactivity, morphology, thermal stability and chemical composition of these materials were characterised by d.c. conductivity measurememts, electron microscopy, thermogravimetry, FTIR and visible absorption spectroscopy and clemental microanalyses. The mass ratio of poly(vinyl acetate) to polypyrrole in the colloidal particles was determined indirectly by spectroscopic assay of the post-reaction supernatant solution for non-adsorbed stabiliser.     

Kinetics of silver nanoparticle growth in aqueous polymer solutions

Silver nanoparticles were prepared in aqueous AgNO₃ solution by using hydroquinone and sodium citrate as reducing agents with neutral polymers poly(vinylpyrrolidone) and poly(vinyl alcohol) as stabilizers. The rate of particle formation was determined with a diode array UV-Vis spectrophotometer. The effects of the polymer concentration on the reaction rate, the size, and the size distribution of the particles formed were studied by transmission electron microscopy. Both the reaction rate and the size of silver nanoparticles decreased with increasing polymer concentration in the range 0.07–0.50 w/v%.     

Stabilization of small unilamellar DMPC-liposomes by uncharged polymers

 Polymer-free and polymer-bearing small unilamellar (SUV) liposomes from dimyristoyl-phosphatidylcholine (DMPC) were prepared under standardized conditions. Polymer-bearing liposomes were formed by incorporating an uncharged polymer [hydrolyzed poly(vinyl alcohol) (PVA), poly(vinyl alcohol-co-vinylacetal) (PVA-Al), poly(vinyl alcohol-co-vinyl propional) (PVA-Prol) poly(vinyl alcohol-co-vinyl butiral) (PVA-Bul) copolymer or poly(vinyl pyrrolidone) (PVP)] into the membrane bilayer of vesicles. The kinetic (long-term) stability of the liposome dispersions stored in distilled water, in physiological NaCl solution and at various pH values, respectively, were studied. The physical stability of vesicles was tested by measuring the size and the zeta potential of liposomes by means of a Malvern Zetasizer 4 apparatus. It was shown that most of these polymers are effective steric stabilizers for the DMPC-liposomes. Among the polymers, the PVA-Bul and PVA-Prol copolymers and the PVP of high molecular mass exhibited the most efficient stabilizing effect at each pH studied, indicating that the formation of a relatively thick polymer layer around the lipid bilayers ensures an enhanced and prolonged physical stability of liposomes. Also, the butiral or propional side chain in the PVA-based copolymers presumably promotes the anchoring of macromolecules to the vesicles. Using these macromolecules, the colloidal interactions between vesicles can be modified and so the physical stability of liposomes and the kinetic stability of liposome dispersions can also be controlled. Received: 20 May 1997 Accepted: 03 September 1997     

Preparation and properties of poly(alkyl vinyl ether-2-ethyl-2-oxazoline) diblock copolymers

A method for the synthesis of well-defined poly(alkyl vinyl ether–2-ethyl-2-oxazoline) diblock copolymers with hydrolytically stable block linkages has been developed. Monofunctional poly(alkyl vinyl ether) oligomers with nearly Poisson molecular weight distributions were prepared via a living cationic polymerization method using chloroethyl vinyl ether together with HI/ZnI₂ as the initiating system and lithium borohydride as the termination reagent. Using the resultant chloroethyl ether functional oligomers in combination with sodium iodide as macroinitiators, 2-ethyl-2-oxazoline was polymerized in chlorobenzene/NMP to afford diblock copolymers. A series of poly(methyl vinyl ether–2-ethyl-2-oxazoline) diblock materials were found to have polydispersities of ≈ 1.3–1.4 and are microphase separated as indicated by two T_g's in their DSC thermograms. These copolymers are presently being used as model materials to study fundamental parameters important for steric stabilization of dispersions in polar media. © 1993 John Wiley & Sons, Inc.     

Dispersion Stability and Electrorheological Properties of Polyaniline Particle Suspensions Stabilized by Poly(vinyl methyl ether)

In the present article, a novel method of stabilization of a semi conductive polyaniline particle nonaqueous suspension of electrorheological (ER) materials was introduced. Using as the steric stabilizer poly(vinyl methyl ether) (PVME), a dispersion polymerization of aniline was performed and stable aqueous dispersions of the polyaniline were obtained. However, a stable colloidal suspension of polyaniline in silicone oil medium can be obtained only with a low concentration of PVME (0.75%), although the average size of the individual, redispersed particles in oil generally decreased with increasing concentration of PVME. At higher concentrations of PVME, formation of highly packed particle aggregates was investigated, as seen in the scanning electron microscopy images. The polyaniline suspension stabilized by 0.75% PVME content exhibited the best dispersing state and, therefore, showed the highest zero-field viscosity. Such a well-stabilized polyaniline suspension also showed the maximum ER property, namely the largest normalized yield stress in an electric field. Copyright 2001 Academic Press.     

Polyvinyl pyridines as flocculating agents

Summary High molecular weight poly 2- and 4-vinyl pyridines were synthesized by ionic polymerisation and their flocculation efficiency tested against kaolin and silica dispersions at pH 3. Low additions of the polymers, around 3 parts per 10₃ parts solid, destabilize the dispersions and clarify silica dispersions to a remarkable extent; however, over-addition of polymer leads to partial restabilization. The flocculation efficiency improves with increase of solids content, especially with clay dispersions. Flocculation efficiency increases with polymer molecular weight, especially over the lower part of the range covered, but is relatively independent of pH in the range 2–4. Quaternization of poly(4-vinyl pyridine) with bromobutane produces a good flocculant for aqueous silica dispersions in which the degree of restabilization on over-dosing depends on the KCI content. TheN-oxide derivatives of the vinyl pyridine polymers do not affect the colloidal stability of silica dispersions. The observations are interpreted in terms of bridging flocculation by the cationic polymer molecules between anionic surface sites on the solid particles.     

In situ polymerization and morphology of polypyrrole obtained in water‐soluble polymer templates

Several water‐soluble polymers were used as templates for the in situ polymerization of pyrrole to determine their effect on the generation of nanosized polypyrrole (PPy) particles. The polymers used include: polyvinyl alcohol (PVA), polyethylene oxide (PEO), poly(vinyl butyral), polystyrene sulfonic acid, poly(ethylene‐alt‐maleic anhydride) (PEMA), poly(octadecene‐alt‐maleic anhydride), poly(N‐vinyl pyrrolidone), poly(vinyl butyral‐co‐vinyl alcohol‐co‐vinyl acetate), poly(N‐isopropyl acrylamide), poly(ethylene oxide‐block‐propylene oxide), hydroxypropyl methyl cellulose, and guar gum. The oxidative polymerization of pyrrole was carried out with FeCl₃ as an oxidant. The morphology of PPy particles obtained after drying the resulting aqueous dispersions was examined by optical microscopy, and selected samples were further analyzed via atomic force microscopy. Among the template polymers, PVA was the most efficient in generating stable dispersions of PPy nanospheres in water, followed by PEO and PEMA. The average size of PPy nanospheres was in the range of 160 nm and found to depend on the molecular weight and concentration of PVA. Model reactions and kinetics of the polymerization reaction of pyrrole in PVA were carried out by hydrogen ¹H NMR spectroscopy using ammonium persulfate as an oxidant. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

The Structures and Physicochemical Properties of Mixtures of Water-Soluble Polymers

Because data on structure, component interaction, physical properties, and compatibility of polymer blends containing native polysaccharides is very sparse, we have used optical and electron microscopy, X-ray diffraction, IR spectroscopy, sorption capacity methods, and estimation of thermodynamic data to investigate the structural, physicochemical, and physicomechanical properties of mixtures of carboxymethylcellulose with poly(vinyl alcohol) and of mixtures of chitosan with poly(vinyl alcohol), to discover relationships between the structures of the systems and their physicochemical characteristics and other properties, to determine the compatibility of components, and to discover methods and conditions for their synthesis. It was found that for some component ratios in these systems there is some interaction and some compatibility, with the result that the structures of the blends are less heterogeneous than those of the individual components. One effect of this is that the physicomechanical properties of the blends can be superior to those of the individual components, particularly for carboxymethylcellulose–poly(vinyl alcohol) mixtures.Presented at: International Symposium on Separation and Characterization of Natural and Synthetic Macromolecules, Amsterdam, The Netherlands, February 5–7, 2003     

Preparation of monodisperse latexes and study of their rheological properties

The synthesis of (monodisperse) poly(styrene) latexes was reexamined using sodiumdodecyl sulfate as emulsifier and potassium persulfate as initiator. It has been shown, that at fixed emulsifier concentration c_E the variation of persulfate amount produces similar particle size variations as changes of electrolyte (potassium sulfate) concentration at a given low initiator level. For c_E << cmc a maximum of particle size versus initiator or electrolyte concentrations has been found. Concentrated monodisperse poly(styrene) dispersions and carboxylated latexes up to 50% have been prepared by a carefully controlled seeding process using monomer feed. Particle size influence on steady shear viscosity has been studied for different kinds of polymer dispersions: for electrostatic stabilized poly(styrene) latexes at high ionic strengths, for electrostatic and sterically stabilized carboxylated latexes at different pH values and for steric stabilized dispersions of poly(vinyl chloride) in plasticizer (dioctyl phthalate). All three kinds of dispersions give pronounced particle size effects on viscosity, which is different from hard-sphere-behaviour. Simple model equations have been formulated to describe the concentration and shear rate dependence on viscosity. Particle size influence may be discussed on the basis of the effective hydrodynamic particle diameter. Causes for the increase of the hydrodynamic particle size are given either by surface swelling or by the formation of particle clusters which are formed and destroyed within the shear field.     

Effect of temperature on the intrinsic viscosity of poly(ethylene glycol)/poly(vinyl pyrrolidone) blends in aqueous solutions

In this work the intrinsic viscosity of poly(ethylene glycol)/poly(vinyl pyrrolidone) blends in aqueous solutions were measured at 283.1–313.1 K. The expansion factor of polymer chain was calculated by use of the intrinsic viscosities data. The thermodynamic parameters of polymer solution (the entropy of dilution parameter, the heat of dilution parameter, theta temperature, polymer–solvent interaction parameter and second osmotic virial coefficient) were evaluated by temperature dependence of polymer chain expansion factor. The obtained thermodynamic parameters indicate that quality of water was decreased for solutions of poly(ethylene oxide), poly(vinyl pyrrolidone) and poly(ethylene oxide)/poly(vinyl pyrrolidone) blends by increasing temperature. Compatibility of poly(ethylene oxide)/poly(vinyl pyrrolidone) blends were explained in terms of difference between experimental and ideal intrinsic viscosity and solvent–polymer interaction parameter. The results indicate that the poly(ethylene glycol)/poly(vinyl pyrrolidone) blends were incompatible.     

Molybdenum disulfide-polymer nanocomposite structures with different sequences of alternating inorganic and organic layers

The reactions of charge-transfer-activated molybdenum disulfide with polymers (polyethylene glycol, poly(ethylene oxide), poly(vinyl alcohol), and polyhexamethylene guanidine hydrochloride) produce nanocomposite compounds, the composition and structure of which are determined by the nature of activated MoS₂. In nanocomposites prepared in single-layer dispersions of molybdenum disulfide, the layers of inorganic and organic components regularly alternate. In nanocomposites, formed by the intercalation of the polymers into particles of nanocrystalline MoS₂, the polymeric molecules are accomodated within spaces between the layers of the inorganic matrix, resulting in the formation of microheterogeneous systems. The structures of these nanocomposite compounds were proposed based on the X-ray powder diffraction and electron microscopy data.     

聚苯胺水基胶体分散液及其复合物的研究 Ⅰ制备、表征及复合物的表观形貌、力学性能

以聚乙烯醇（ＰＶＡ）为稳定剂（ｓｔｅｒｉｃｓｔａｂｉｌｉｚｅｒ）利用分散聚合（ｄｉｓｐｅｒｓｉｏｎｐｏｌｙｍｅｒｉ ｚａｔｉｏｎ）的原理，成功地制备出了稳定的聚苯胺（ＰＡｎ）水基胶体分散液．聚苯胺颗粒的大小受聚合条件如稳定剂浓度、单体浓度、温度以及搅伴状态等的影响．ＰＶＡ通过物理作用吸附在ＰＡｎ颗粒的表面，起到阻止ＰＡｎ颗粒进一步团聚的作用．但这种作用力较弱．ＰＡｎ颗粒的原始尺寸大小约为２０ｎｍ．由此原始颗粒组成了尺寸在１００ｍｍ～２００ｍｍ左右的稳定颗粒     

Monodisperse polystyrene microspheres prepared by dispersion polymerization with microwave irradiation

Monodisperse polystyrene microspheres with diameters of 200–500 nm were prepared by dispersion polymerization with microwave irradiation with poly(N‐vinylpyrrolidone) as a steric stabilizer and 2,2′‐azobisisobutyronitrile as a radical initiator in an ethanol/water medium. The morphology, size, and size distribution of the polystyrene microspheres were characterized with transmission electron microscopy and photon correlation spectroscopy, and the formed films of the polystyrene dispersions were characterized with atomic force microscopy. The effects of the monomer concentration, stabilizer concentration, and initiator concentration on the size and size distribution of the polystyrene microspheres were investigated. The polystyrene microspheres prepared by dispersion polymerization with microwave irradiation were smaller, more uniform, and steadier than those obtained with conventional heating. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2368‐2376, 2005     

Preparation and characterization of poly(vinyl alcohol)/organo-modified cloisite Na+ with chiral L-leucine amino acid/TiO2 nanocomposites

Poly(vinyl alcohol)/organo-clay/TiO₂ nanocamposites films were prepared with 10 wt % of organo-nanoclay and various amount of TiO₂ nanoparticles. Cloisite Na⁺ has been modified via cation exchange reaction using ammonium salt of natural L-leucine amino acid as a cationic surfactant. After that poly(vinyl alcohol)/organo-nanoclay/TiO₂ nanocomposites were synthesized by dispersion of TiO₂ on the surfaces of organo-nanoclay in poly(vinyl alcohol) matrix by using ultrasonic energy. Three nanocomposites with different loading of TiO₂ were prepared and characterized by X-ray diffraction, fourier transform infrared spectroscopy, field emission type scanning electron microscope, scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis and ultraviolet-visible transmission spectra. The results showed that the organo-nanoclay and TiO₂ were dispersed homogeneously in poly(vinyl alcohol) matrix and also showed improvement in their thermal properties compared with the pure poly(vinyl alcohol).     

Palladium nanoparticles from solvated atoms—stability and HRTEM characterization

Palladium particles of nanometric dimensions were synthesized by the chemical liquid deposition method in which the Pd atoms were co-deposited at 77 K with 2-propanol, acetone, and tetrahydrofurane vapor to obtain colloidal dispersions. The colloidal dispersions were characterized by UV–visible spectrophotometry, transmission electron microscopy (TEM) and high-resolution TEM (HRTEM). The palladium colloids synthesized by use of these solvents are very stable. A strong absorption band in the UV region suggests that quantum confinement occurs in the nanoparticles obtained by this procedure. Studies of TEM micrographs reveal average size distributions between 1 and 5 nm for all Pd colloids. Whereas particle sizes in Pd–2-propanol colloids are not very sensitive to concentration change, the particle-size average in Pd–acetone and Pd–THF increases by 0.5 nm when the concentration increases from 10^–3 to 10^–2 mol l^–1. The HRTEM results show the high crystallinity of Pd nanoparticles and three low-energy structure shapes were found: cuboctahedron, tetrakaidecahedron, and icosahedron.