Local heat transfer in the first baffle compartment of the shell-and-tube heat exchangers for staggered tube arrangement

A mass transfer measuring method based on absorption, chemical and coupled colour reaction is used to visualize and determine the shell side local heat transfer in the first baffle compartment of shell-and-tube heat exchangers with segmental baffles for staggered tube arrangement. Local mass transfer coefficients were transformed into heat transfer coefficients by using the analogy between heat and mass transfer. The local, per-tube and integral heat transfer coefficient distributions are presented.     

The influence of oil on nucleate pool boiling heat transfer

The influence of various oil contents in R134a is investigated for nucleate pool boiling on copper tubes either sandblasted or with enhanced heating surfaces (GEWA-B tube). Polyolester oils (POE) (Reniso Triton) with medium viscosity 55 cSt (SE55) and high viscosity 170 cSt (SE170) were used. Heat transfer coefficients were obtained for boiling temperatures between −28.6 and +20.1°C. The oil content varied from 0 to 5% mass fraction. For the sandblasted tube and the SE55 oil the heat transfer coefficients for the refrigerant/oil-mixture can be higher or lower than those for the pure refrigerant, depending on oil mass fraction, boiling temperature and heat flux. In some cases the highest heat transfer coefficients were obtained at a mass fraction of 3%. For the 170 cSt oil there is a clear decrease in heat transfer for all variations except for a heat flux 4,000 W/m² and −10.1°C at 0.5% oil content. The heat transfer coefficients are compared to those in the literature for a smooth stainless steel tube and a platinum wire. For the enhanced tube and 55 cSt oil the heat transfer coefficients are clearly below those for pure refrigerant in all cases. The experimental results for the sandblasted tube are compared with the correlation by Jensen and Jackman. The calculated values are within +20 and −40% for the medium viscosity oil and between +50% and −40% for the high viscosity oil. A correlation for predicting oil-degradation effects on enhanced surfaces does not exist.     

Model investigations of convective heat transfer and pressure loss in diagonal membrane heating surfaces

 The paper presents the results of an investigation concerning heat transfer and pressure loss in air crossflow of diagonally shaped membrane heating surfaces. The heat and mass transfer analogy by means of naphthalene sublimation technique is used in order to evaluate mean Nusselt number values in such tube banks. The effect of tube bank arrangement on heat transfer coefficients and flow resistance is discussed. Convective heat transfer and pressure loss characteristics of diagonally shaped membrane tube banks, plain tube banks and ordinary membrane tube banks are compared. Received on 15 June 2000 / Published online: 29 November 2001     

The cooling heat transfer characteristics of the supercritical CO2 in micro-fin tube

This study intended to verify the cooling heat transfer characteristics of supercritical gas for refrigerating and air-conditioning devices that use CO₂, a natural refrigerant, as the operating fluid. Experiments were performed with a gas cooler, which was the test part. The gas cooler was a heat exchanger made of a micro-fin tube with an inner diameter of 4.6 mm and an outer diameter of 5.0 mm. The experiment results are summarized as follows. The heat transfer coefficient, according to the mass flux, peaked at the low cooling pressure of 8.0 MPa in the gas cooler, and reached its minimum at the high pressure of 10.0 MPa. Furthermore, when the mass flux of the refrigerant increased, the coefficient increased faster with the lower cooling pressure in the gas cooler. The heat transfer coefficient, according to the shape of the heat transfer tube, showed that the maximum values of the CO₂ cooling heat transfer coefficients of the smooth tube and the micro-fin tube were found at 44.7 °C, which were the pseudo-critical temperatures for the entrance pressures. It was found that the cooling heat transfer coefficient of the micro-fin tube increased by 12–39 % more than that of the smooth tube. The experiment results for the CO₂ heat transfer coefficients of the smooth tube and the micro-fin tube were compared with the results estimated from previous correlations. It was found that the experiment values generally significantly differed from and the experiment values greater than the estimated values. The differences were especially greater in the vicinity of the critical temperature points. Based on these results, a new correlation was suggested that includes the density ratio and the specific heat ratio.     

Flow boiling heat transfer in a vertical spirally internally ribbed tube

 Experiments of flow boiling heat transfer and two-phase flow frictional pressure drop in a spirally internally ribbed tube (φ22×5.5 mm) and a smooth tube (φ19×2 mm) were conducted, respectively, under the condition of 6×10⁵ Pa (absolute atmosphere pressure). The available heated length of the test sections was 2500 mm. The mass fluxes were selected, respectively, at 410, 610 and 810 kg/m² s. The maximum heat flux was controlled according to exit quality, which was no more than 0.3 in each test run. The experimental results in the spirally internally ribbed tube were compared with that in the smooth tube. It shows that flow boiling heat transfer coefficients in the spirally internally ribbed tube are 1.4–2 times that in the smooth tube, and the flow boiling heat transfer under the condition of smaller temperature differences can be achieved in the spirally internally ribbed tube. Also, the two-phase flow frictional pressure drop in the spirally internally ribbed tube increases a factor of 1.6–2 as compared with that in the smooth tube. The effects of mass flux and pressure on the flow boiling heat transfer were presented. The effect of diameters on flow boiling heat transfer in smooth tubes was analyzed. Based on the fits of the experimental data, correlations of flow boiling heat transfer coefficient and two-phase flow frictional factor were proposed, respectively. The mechanisms of enhanced flow boiling heat transfer in the spirally internally ribbed tube were analyzed. Received on 1 December 1999     

Numerical study on heat transfer and resistance characteristics of supercritical water inside internally-ribbed tube

The effects of structural parameters for internally-ribbed tube on heat transfer and flow characteristics of supercritical water were studied numerically. The results show that the heat transfer and pressure loss increases with the increase of mass flow or heat flux. The Heat transfer and resistance coefficients of supercritical water increase with the spiral rising angle decrease or rib height increase, while rib width has a weak influence on heat transfer and pressure drop.     

Heat transfer characteristics of a new helically coiled crimped spiral finned tube heat exchanger

In the present study, the heat transfer characteristics in dry surface conditions of a new type of heat exchanger, namely a helically coiled finned tube heat exchanger, is experimentally investigated. The test section, which is a helically coiled fined tube heat exchanger, consists of a shell and a helical coil unit. The helical coil unit consists of four concentric helically coiled tubes of different diameters. Each tube is constructed by bending straight copper tube into a helical coil. Aluminium crimped spiral fins with thickness of 0.5 mm and outer diameter of 28.25 mm are placed around the tube. The edge of fin at the inner diameter is corrugated. Ambient air is used as a working fluid in the shell side while hot water is used for the tube-side. The test runs are done at air mass flow rates ranging between 0.04 and 0.13 kg/s. The water mass flow rates are between 0.2 and 0.4 kg/s. The water temperatures are between 40 and 50°C. The effects of the inlet conditions of both working fluids flowing through the heat exchanger on the heat transfer coefficients are discussed. The air-side heat transfer coefficient presented in term of the Colburn J factor is proportional to inlet-water temperature and water mass flow rate. The heat exchanger effectiveness tends to increase with increasing water mass flow rate and also slightly increases with increasing inlet water temperature.     

Calculation of overall heat transfer coefficients in a triple tube heat exchanger

In previous studies, calculation of overall heat transfer coefficients in a triple tube heat exchanger (TTHE) involved assumptions or approaches those are not valid in all cases. In this study a more generic way of calculating overall heat transfer coefficients in a TTHE has been developed. Consequently, temperature profiles of all streams in a TTHE in the axial direction were determined. An effective overall heat transfer coefficient that is related to the total resistance to heat transfer in the TTHE, was also determined to facilitate comparison of a TTHE to an equivalent double tube heat exchanger.     

The effect of flexible tube vibration on pressure drop and heat transfer in heat exchangers considering viscous dissipation effects

The pressure drop and heat transfer coefficient in tube bundle of shell and tube heat exchangers are investigated considering viscous dissipation effects. The governing equations are solved numerically. Because of temperature-dependent viscosity the equations should be solved simultaneously. The flexible tubes vibration is modeled in a quasi-static method by taking the first tube of the row to be in 20 asymmetric positions with respect to the rest of the tubes which are assumed to be fixed and time averaging the steady state solutions corresponding to each one of these positions .The results show that the eccentricity of the first tube increases pressure drop and heat transfer coefficients significantly comparing to the case of rigid tube bundles, symmetrically placed. In addition, these vibrations not only compensate the effect of viscous dissipations on heat transfer coefficient but also increase heat transfer coefficient. The constant viscosity results obtained from our numerical method have a good agreement with the available experimental data of constant viscosity for flexible tube heat exchangers.     

Visualisation of flow boiling heat transfer in a microtube

This paper presents the results of the flow boiling patterns and heat transfer coefficients of FC-72 in a small tube. The internal diameter of the tube is 0.48 mm, with a heated length of 73 mm. The mass flow rate varies from 50 to 3,000 kg/m²-s. The microtube is made of Pyrex in order to obtain the visualisation of the flow pattern along the heated channel. Different types of flow pattern have been observed: bubbly flow, deformed bubbly flow, bubbly/slug flow, slug flow, slug/annular flow, and annular flow. The experiments show the presence of flow instabilities in a large portion of the tests at low mass flow rates and low subcooling. Flow patterns in presence of flow instabilities are mainly characterized by bubbly/slug flow and slug/annular flow. Heat transfer rates have been studied in all flow pattern conditions. The two groups of results, with flow instabilities and without flow instabilities, show similar heat transfer behaviour. The heat transfer characteristics of the pipes have been studied in comparison with mass flux and vapour quality.     

Augmented heat transfer and pressure drop of strip-type inserts in the small tubes

An experiment is carried out to investigate the characteristics of the augmentation of heat transfer and pressure drop by different strip-type inserts in small tube having an inside diameter of 2.0 mm. The effects of the imposed wall heat flux, mass flux, strip inserts with various configurations (heights, widths, pitches) on the measured augmentative heat transfer and pressure drop are examined in detail. In order to obtain insight into the fluid flow phenomena, flow visualization was also made to observe the detailed fluid flow characteristics of the present tubes inserted with strip-type inserts. In addition, comparisons are made with a plain tube having the same length, heat transfer area and experimental conditions. The measured heat transfer coefficients and pressure drops for this small pipe are also emphasized to compare with those for larger pipes. Furthermore, in order to compare results from the different configurations of strip-type inserts, several enhancement factors and performance ratios are defined to account for the effects of augmentation. Moreover, correlation equations for the heat transfer coefficient and pressure drop of the present study are proposed.The financial support extended by the National Science Council of the Republic of China through grant No. NSC-89-2212-E-230-004.     

The influence of tube bundle geometry on cross-flow boiling heat transfer and pressure drop

An experimental investigation was performed to compare the boiling heat transfer coefficients and two-phase pressure drops from a square inline and a staggered tube bundle having the same tube pitch-to-diameter ratio (P/D = 1.30) and from two square inline tube bundles having different pitch-to-diameter ratios (P/D = 1.30 and 1.70). Except at the highest heat fluxes the heat transfer coefficients generally were higher in the staggered tube bundle than in the inline tube bundle and higher in the larger P/D tube bundle than in the smaller. As the heat flux increased, the differences decreased. The differences were attributed to the tradeoff between nucleation and convection. The staggered tube bundle had higher pressure drops than the inline bundle except at low mass velocities; the larger pressure drop in the staggered bundle was attributed to the combination of a larger void fraction and a larger friction multiplier, with the frictional component dominating at higher mass velocities. Comparing the inline tube bundle pressure drops, it was concluded that the larger P/D bundle had a larger void fraction than the smaller P/D tube bundle; no conclusions could be drawn regarding the relative magnitude of the two-phase fraction multiplier.     

Condensing heat transfer characteristics of hydrocarbon refrigerants in 9.52 and 12.7 mm smooth tube

Experimental results for heat transfer characteristic and pressure gradients of hydrocarbon (HC) refrigerants and R-22 during condensing inside horizontal double pipe heat exchangers are presented. The test sections which have one tube diameter of 12.70 mm with 0.86 mm wall thickness, another tube diameter of 9.52 mm with 0.76 mm wall thickness are used for this investigation. The local condensing heat transfer coefficients of HC refrigerants were higher than that of R-22. The average condensing heat transfer coefficient increased with the increase of the mass flux. It showed the higher values in HC refrigerants than R-22. Comparing the heat transfer coefficient of experimental results with that of other correlations, the presented results had a good agreement with most of the Cavallini’s correlations.     

Heat and mass transfer characteristics of absorption of R134a into DMAC in a horizontal tube absorber

In this paper the heat and mass transfer characteristics of a horizontal tube absorber for the mixture R134a/DMAC in terms of experimentally gained heat and mass transfer coefficients are presented. The heat transfer coefficient is mainly dependent on the solution’s mass flow rate. The mass transfer coefficient is strongly related to the subcooling of the solution. The data are compared to experimental absorption characteristics of water into aqueous lithium bromide in an absorption chiller. The mass transfer coefficients are of similar size whereas the heat transfer coefficients are about one order of magnitude smaller for R134a-DMAC.     

Flow boiling heat transfer of R134a in the multiport minichannel heat exchangers

The flow boiling heat transfer characteristics of R134a in the multiport minichannel heat exchangers are presented. The heat exchanger was designed as the counter flow tube-in-tube heat exchanger with refrigerant flowing in the inner tube and hot water in the gap between the outer and inner tubes. Two inner tubes were made from extruded multiport aluminium with the internal hydraulic diameter of 1.1 mm for 14 numbers of channels and 1.2 mm for eight numbers of channels. The outer surface areas of two inner test sections are 5979 mm² and 6171 m², while the inner surface areas are 13,545 mm² and 8856 mm² for 14 and eight numbers of channels, respectively. The outer tube of heat exchanger was made from circular acrylic tube with an internal hydraulic diameter of 25.4 mm. The experiments were performed at the heat fluxes between 15 and 65 kW/m², mass flux of refrigerant between 300 and 800 kg/m² s and saturation pressure ranging from 4 to 6 bar. For instance the boiling curve, average heat transfer coefficients are discussed. The comparison results of two test sections with different the number of channels are investigated. The results are also compared with nine existing correlations. The new correlation for predicting the heat transfer coefficient was also proposed.     

Flow boiling heat transfer of R134a and R404A in a microfin tube at low mass fluxes and low heat fluxes

An experimental investigation of flow boiling heat transfer in a commercially available microfin tube with 9.52 mm outer diameter has been carried out. The microfin tube is made of copper with a total fin number of 55 and a helix angle of 15°. The fin height is 0.24 mm and the inner tube diameter at fin root is 8.95 mm. The test tube is 1 m long and is electrically heated. The experiments have been performed at saturation temperatures between 0 and −20°C. The mass flux was varied between 25 and 150 kg/m²s, the heat flux from 15,000 W/m² down to 1,000 W/m². All measurements have been performed at constant inlet vapour quality ranging from 0.1 to 0.7. The measured heat transfer coefficients range from 1,300 to 15,700 W/m²K for R134a and from 912 to 11,451 W/m²K for R404A. The mean heat transfer coefficient of R134a is in average 1.5 times higher than for R404A. The mean heat transfer coefficient has been compared with the correlations by Koyama et al. and by Kandlikar. The deviations are within ±30% and ±15%, respectively. The influence of the mass flux on the heat transfer is most significant between 25 and 62.5 kg/m²s, where the flow pattern changes from stratified wavy flow to almost annular flow. This flow pattern transition is shifted to lower mass fluxes for the microfin tube compared to the smooth tube.     

Two-phase heat transfer characteristics for R-22/R-407C in a 6.5-mm smooth tube

Two-phase friction and heat transfer characteristics for R-22/R-407C inside a 6.5-mm smooth tube are reported in this study. The heat transfer results for G=100 and 400 kg/m² s were reported in the present study, and the adiabatic frictional pressure drop was recorded in the range of 100 to 700 kg/m² s. It is found that the development of flow pattern for R-407C falls behind R-22. This may explain the lower pressure drops for R-407C. The major heat transfer mechanism at low mass flux is nucleate boiling, and virtually becomes the convective evaporation as mass flux increase to G=400 krg/m² s, Meanwhile, the reduction of heat transfer coefficients for R-407C mixtures are especially profound at low mass flux, and the reduction of heat transfer coefficient decreases with the increase of mass flux.     

Heat transfer coefficients of shell and coiled tube heat exchangers

In the present study, the heat transfer coefficients of shell and helically coiled tube heat exchangers were investigated experimentally. Three heat exchangers with different coil pitches were selected as test section for both parallel-flow and counter-flow configurations. All the required parameters like inlet and outlet temperatures of tube-side and shell-side fluids, flow rate of fluids, etc. were measured using appropriate instruments. Totally, 75 test runs were performed from which the tube-side and shell-side heat transfer coefficients were calculated. Empirical correlations were proposed for shell-side and tube-side. The calculated heat transfer coefficients of tube-side were also compared to the existing correlations for other boundary conditions and a reasonable agreement was observed.     

Evaporation flow pattern and heat transfer of R-22 and R-134a in small diameter tubes

The flow patterns and heat transfer coefficients of R-22 and R-134a during evaporation in small diameter tubes were investigated experimentally. The evaporation flow patterns of R-22 and R-134a were observed in Pyrex sight glass tubes with 2 and 8 mm diameter tube, and heat transfer coefficients were measured in smooth and horizontal copper tubes with 1.77, 3.36 and 5.35 mm diameter tube, respectively. In the flow patterns during evaporation process, the annular flows in 2 mm glass tube occurred at a relatively lower vapor quality compared to 8 mm glass tube. The flow patterns in 2 mm glass tube did not agree with the Mandhane’s flow pattern maps. The evaporation heat transfer coefficients in the small diameter tubes (d _i  < 6 mm) were observed to be strongly affected by tube diameters, and to differ from those in the large diameter tubes. The heat transfer coefficients of 1.77 mm tube were higher than those of 3.36 mm and 5.35 mm tube. Most of the existing correlations failed to predict the evaporation heat transfer coefficient in small diameter tubes. Therefore, based on the experimental data, the new correlation is proposed to predict the evaporation heat transfer coefficients of R-22 and R-134a in small diameter tubes.     

Free convection heat transfer from the outer surface of vertically oriented helical coils in glycerol-water solution

Steady state natural convection heat transfer from vertical helical coiled tubes, in glycerol-water solution 57% (g/w) by mass, is studied experimentally. Average heat transfer coefficients were obtained for laminar and transition to turbulent natural convection. The experiments have been carried out for three coil diameter to tube diameter ratios, D/d_o, and for five and ten coil turns, N. Effects of Rayleigh number, D/d_o ratios, and N on the heat transfer behavior of the coils are investigated. Correlations are presented to calculate the average Nusselt number in terms of Rayleigh number, D/d_o ratios, and N. The results show that the heat transfer coefficient is enhanced either by reducing the diameter ratio or the number of coil turns. The overall correlations covering all the data points using the coil length as a characteristic length are also presented.