木质素磺酸钠改性聚砜膜的制备及其在正渗透膜中的应用

采用木质素磺酸钠作为亲水添加剂,通过浸没沉淀相转化法制备了木质素磺酸钠共混改性聚砜膜,以改善聚砜膜的亲水性,并用作正渗透膜的支撑层,以降低内浓差极化效应.利用扫描电子显微镜、衰减全反射傅里叶变换红外光谱仪、水接触角仪等研究了不同木质素磺酸钠添加量对聚砜膜的结构和表面性质的影响.结果表明,添加木质素磺酸钠后,聚砜膜的指状孔变得规整且狭长.水接触角实验证实添加木质素磺酸钠能改善聚砜膜的亲水性,当木质素磺酸钠含量为0.4 wt%时,聚砜膜的表面水接触角可降低至65°.正/反渗透测试装置分别用于表征正渗透膜的传质性质和结构参数.结果表明,以0.4 wt%木质素磺酸钠改性聚砜膜为支撑层的正渗透膜的水渗透性能(A=3.12×10~(-5) LMH×Pa~(-1))优于纯聚砜基底正渗透膜(0.76×10~(-5)LMH×Pa~(-1)),而且前者的结构参数(S=2010mm)远小于后者(3450mm),说明木质素磺酸钠改性聚砜膜有效弱化了正渗透膜的内浓差极化效应.     

SmO对氢镍电池镍电极性能的影响

通过对模拟电池进行恒流充放电、交流阻抗等测试和析气实验,研究了在亚镍中掺杂氧化钐SmO对镍电极电化学性能的影响。结果表明,掺杂氧化钐SmO的质量分数在1.0%时,镍电极的电化学阻抗变小,提高了镍电极电化学活性、高温性能与充电效率,能够有效抑制充电过程中氧的产生,在室温条件下以0.2C充放电时,掺杂SmO镍电极的放电比容量为138.04 mAh.g-1,比空白镍电极提高了23.01%;50℃下1C充放电时,放电比容量为90.313 mAh.g-1,较未添加氧化钐提高8.69%。     

木质素/氧化锌复合颗粒的制备及在水性聚氨酯中的应用

通过沉淀法以季铵化木质素(LQAs)、醋酸锌和NaOH为原料制备了不同木质素负载量的木质素/氧化锌(LQAs/ZnO)复合颗粒.测试结果表明,LQAs/ZnO复合颗粒是由LQAs和ZnO形成的杂化结构,且NaOH用量对LQAs/ZnO复合颗粒的形貌有显著影响.与纯ZnO相比,复合颗粒对紫外光的吸收明显增强.此外,探究了复合颗粒掺杂改性的水性聚氨酯(WPU)复合薄膜的光学和力学性能.与0.6%(质量分数)的LQAs/ZnO复合颗粒均匀共混成膜的WPU复合薄膜的断裂拉伸强度和断裂伸长率相较于纯WPU薄膜,分别提高了81.5%和10.9%.经过192h紫外光老化测试后,断裂拉伸强度保持在25 MPa以上,断裂伸长率保持在360%以上,表明LQAs/ZnO复合颗粒可有效提高WPU薄膜的紫外屏蔽性能和抗紫外老化性能.     

木质素磺酸盐的分离提纯

以粗木质素磺酸钠为原料, 采用树脂法、超滤法、长链胺法和溶剂萃取法对其进行了提纯. 红外光谱、元素分析、凝胶渗透色谱等测试结果表明, 溶剂萃取法不能达到提纯目的; 树脂法、超滤法、长链胺法可除去相对分子量小于1000的杂质, 粗木质素磺酸钠经提纯后木质素磺酸钠的质量分数从59.0%提高到90%左右, 且提纯产品的重均分子量和数均分子量均增大, 分子量分布更均一. 从产品收率、提纯效果及提纯工艺等3方面分析表明, 长链胺法除糖效果最好, 提纯后糖含量下降了50%; 超滤法的收率最高, 可达31%, 且其提纯产品的重均分子量较高, 达到12000, 比粗木钠提高了1倍以上.     

软硬段对聚氨酯弹性体结构性能的影响

采用本体聚合和溶液聚合两种方法,合成了一系列用聚乙二酸丁二醇酯二醇作为软段的聚氨酯弹性体。研究了不同硬段含量和聚醚添加量对聚氨酯弹性体综合性能的影响。利用红外光谱,机械性能测试、热分析、耐水解老化实验和记忆回弹性能等测试对样品进行表征与分析。结果表明:当硬段含量为33%～34%,软段中聚醚添加量为4%～5%(占软段的质量分数)时,弹性体具有较好的力学性能和耐老化性能,弹性回复率可维持在80%～85%。     

软硬段对聚氨酯弹性体结构性能的影响

采用本体聚合和溶液聚合两种方法,合成了一系列用聚乙二酸丁二醇酯二醇作为软段的聚氨酯弹性体。研究了硬段含量和聚醚添加量对聚氨酯弹性体综合性能的影响。利用红外光谱、热分析、力学性能测试、记忆回弹性能和耐水解老化实验等测试手段对样品进行了表征与分析。结果表明:硬段质量含量为31%~35%时,材料的力学性能较优,形状回复率可以达到75%~85%;软段中聚醚添加量在4%~5%(占软段的质量分数)时,弹性体具有较好的力学性能和耐水解性能。     

利用造纸污泥制备木素基阳离子絮凝剂及其性能的研究

以造纸污泥中提取的木质素为原料,合成了木素基阳离子絮凝剂。研究了催化剂种类、反应物配料比、反应温度、反应时间等对合成产物脱色性能的影响,确定了较佳合成工艺条件为:引发剂K2S2O8用量为木质素磺酸钠质量的0.7%,活化时间1.5 min,木质素磺酸钠与单体质量比为1∶1.5,反应温度为70℃,反应时间1.5 h,采用红外光谱对产物结构进行了表征。产物对几种模拟染料废水具有良好的脱色性能,在酸性(pH1～2)条件下,脱色率均达84.4%以上。通过比较木质素与接枝产物的絮凝效果以及絮体的微观形貌,对其絮凝机理进行了初步探讨。     

酞菁钴对AB_3型储氢合金的电化学性能影响

为了改善储氢合金La_(0.73)Ce_(0.18)Mg_(0.09)Ni_(3.20)Al_(0.21)Mn_(0.10)Co_(0.60)的电化学性能,通过添加酞菁钴到储氢合金中并考察其电化学性能的影响。通过红外图谱、紫外分析、X射线粉末衍射仪(XRD)及扫描电镜(SEM)技术发现合成出的酞菁钴只是简单的附着在合金表面,并未改变合金的相结构。电化学测试结果表明:添加酞菁钴后的合金电极的循环稳定性有大幅度提升,添加质量分数为1%酞菁钴后电极的容量保持率(C_(50)/C_(max))由初始的63%提高至79%;合金电极的交换电流密度、极限电流密度以及表面的电子转移速率均有改善。结果表明添加酞菁钴可改善储氢合金的电化学性能。     

金属锂在含(亚)硫酰基添加剂电解液中电化学可逆性研究

分别以亚硫酰氯(SOCl2)、硫酰氯(SO2Cl2)、二甲亚砜(DMSO)、苯磺酰氯(BSC)和苯基乙烯基亚砜(PVSO)作为添加剂, 加入至1 mol•L－1 LiPF6/碳酸乙烯酯(EC)＋碳酸二甲酯(DMC)(体积比为1∶1)电解液中, 采用恒电流沉积-溶出法、循环伏安法(CV)、电化学阻抗谱(EIS)、X射线光电子能谱(XPS)测试技术, 研究了添加剂对电化学金属锂沉积-溶出可逆性以及金属锂负极/电解液界面性质的影响. 电化学测试结果表明, 添加SO2Cl2和BSC能显著改善金属锂电极的循环性能, 100% DOD(锂全溶出)条件下, 循环效率稳定在90%左右. 电化学测试、添加剂分子电子亲和能计算并结合XPS测试结果表明, 较早反应成膜的SO2Cl2和BSC添加剂可以在一定程度上抑制电解液溶剂的分解, 使锂电极循环效率和寿命得以提高. 洞察和比较添加剂的结构揭示, 含磺酰基的化合物明显优于含亚磺酰基的化合物.     

挤出成型法制备添加铁离子的管式阳极支撑固体氧化物燃料电池（英文）

本文通过挤出成型法,成功制备了管式固体氧化物烘焙电池阳极支撑体,并以YSZ为电解质,LSM为阴极组装成电池测试其电化学性能。为了改善阳极的结构,在阳极粉料分别中添加了三种造孔剂:石墨、玉米粉和淀粉,并进行了单电池的组装及电池性能测试。SEM分析和电化学测试结果都表明,与玉米粉和淀粉相比,石墨为造孔剂效果更好。另外,为了进一步优化阳极的性能,本文在以石墨为造孔剂时,同时在阳极中添加了相当于5%mol Ni的Fe离子。SEM结果显示Fe离子的加入能够减少阳极的烧结,优化阳极结构。随后的电化学性能测试亦表明,随着Fe离子的加入,单电池的性能从241m W·cm~(-2)提高到了400m W·cm~(-2)。而由于Fe的电阻大于Ni,电池的欧姆阻抗与未添加Fe离子时相比有了一定的提高。     

Voltammetric and electrochemical impedimetric behavior of silica-based gel electrolyte for valve-regulated lead-acid battery

The gel electrolyte is an important component of the valve-regulated lead-acid (VRLA) batteries. In this study, fumed silica-based gel electrolyte systems were prepared. In this concept, several important parameters controlling the performance of the GEL-VRLA battery, such as the sulfuric acid and fumed silica concentrations, gel formulation, gelling time and rate, and different additives (Na₂SO₄ and MgSO₄), were scientifically investigated. The gel formulations were characterized by cyclic voltammetric and electrochemical impedance spectroscopic methods. The optimum parameters were determined by using the results of anodic peak currents and redox capacities, R _s and R _ct values. Addition of 6 % (w/w) fumed silica to 30 % (w/w) sulfuric acid, for preparation of gelled electrolyte, increased the battery performance significantly. According to the results of the transmission electron and optic microscope images of the gel electrolytes, the three-dimensional gel structure was prepared successfully. The optimization of sulfuric acid concentration and amount of Na₂SO₄ and MgSO₄ additives were examined for the first time in detail by cyclic voltammetry, electrochemical impedimetry, and battery test. Na₂SO₄ and MgSO₄ additives make a good combination with a gelled-electrolyte system and improve the charge/discharge capacity according to sulfuric acid electrolytes. According to the experimental results, the fumed silica-based gel electrolyte system has a great potential for application in gelled electrolyte VRLA batteries.     

Efficient gel‐type electrolyte with bismaleimide via in situ low temperature polymerization in dye‐sensitized solar cells

This study reports the characteristics of gel‐type dye‐sensitized solar cells (DSSCs), fabricated with gel‐type electrolyte containing poly‐1,1′‐(methylenedi‐4,1‐phenylene)bismaleimide (PBMI), or poly‐1,1′‐(3,3′‐dimethyl‐1,1′‐biphenyl‐4,4′‐diyl)bismaleimide (PDBBMI), or poly‐N,N′‐(4‐methyl‐1,3‐phenylene)bismaleimide (PMPBMI), prepared by in situ polymerization of the corresponding monomer without an initiator at 30 °C. Incorporating 0.3 wt % content of exfoliated alkyl‐modified nanomica (EAMNM) into PBMI‐gelled electrolyte leads to higher short‐circuit current density (J_sc = 17.14 mA cm^?2) and efficiency (η = 7.02%) than that of neat PBMI‐gel electrolyte (J_sc = 15.32 mA cm^?2, η = 6.41%). Incorporating 0.3 wt % EAMNM into PBMI‐gelled electrolyte results in remarkably stable device performance under continuous light soaking under one sun (100 mW cm^?2) at 55 °C. The efficiency of DSSCs based on PBMI/0.3 wt % EAMNM‐gelled electrolyte drops by only 1.7% (η = 6.93%) after 500 h of continuous light soaking. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

新型PMMA基聚合物电解质的研制

制备了聚甲基丙烯酸甲酯（PMMA）基聚合物电解质，通过加入交联剂使其形成网状结构，提高了聚合物电解质的机械性能.对MMA以及交联剂的含量作了优化，并测试了聚合物电解质的温度特性.测试结果表明,MMA、EGD(二甲基丙烯酸乙二醇酯)和电解液(LiBF4/EC DMC)含量分别为25％、2％、73％(质量分数）时，所制备的聚合物电解质具有较高的电导率，室温条件下可以达到2×10－3 S•cm－1，电化学窗口为4.8 V.用其作为电解质组装的聚合物锂离子电池具有较好的充放电性能.     

Conductivities and transport properties of gelled electrolytes with and without an ionic liquid for Li and Li-ion batteries

Conductivity and transport properties have been determined for gelled polymer electrolytes of three compositions: a base PVdF-polymer gel with organic carbonate solvents as plasticizers and LiN(SO(2)C(2)F(5))(2) electrolyte, a second polymer electrolyte with 5 mass % 1-ethyl-3-methylimidazolium bisperfluoroethylsulfonyl imide (EMI-BETI) added to the base polymer electrolyte, and a third PVdF polymer electrolyte using only EMI-BETI as the plasticizer. Conductivities were studied over the temperature range +25 to -40 degrees C, and for all three gels, the temperature dependence of the conductivities was found to follow the VTF equation, which is consistent with the free volume model for ion transport. For the gel containing 5 mass % EMI-BETI, transport numbers were determined from +50 to -20 degrees C and were found to decrease as the temperature decreased. Although there are no theoretical models to treat and interpret the temperature dependence of transport numbers, we found that a modified VTF equation resulted in an excellent fit to the temperature dependence of the transport number, which is another confirmation of a free volume model for transport in these gelled polymer electrolytes.     

Enhancement of photocurrent of polymer‐gelled dye‐sensitized solar cell by incorporation of exfoliated montmorillonite nanoplatelets

Poly(n‐isopropylacrylamide) (PNIPAAm) and its nanocomposite with exfoliated montmorillonite (MMT) were prepared by soap‐free emulsion polymerization and individually applied to gel the electrolyte systems for the dye‐sensitized solar cells (DSSCs). Each exfoliated MMT nanoplatelet had a thickness of ～ 1 nm, carried ～ 1.8 cation/nm², and acted like a two‐dimensional electrolyte. The DSSC with the LiI/I₂/tertiary butylpyridine electrolyte system gelled by this polymer nanocomposite had higher short‐circuit current density (J_sc) compared to that gelled by the neat PNIPAAm. The former has a J_sc of 12.6 mA/cm², an open circuit voltage (V_oc) of 0.73 V, and a fill factor (FF) of 0.59, which harvested 5.4% electricity conversion efficiency (η) under AM 1.5 irradiation at 100 mW/cm², whereas the latter has J_sc = 7.28 mA/cm², V_oc = 0.72 V, FF = 0.60, and η = 3.17%. IPCE of the nanocomposite‐gelled DSSC were also improved. Electrochemical impedance spectroscopy of the DSSCs revealed that the nanocomposite‐gelled electrolytes significantly decreased the impedances in three major electric current paths of DSSCs, that is, the resistance of electrolytes and electric contacts, impedance across the electrolytes/dye‐coated TiO₂ interface, and Nernstian diffusion within the electrolytes. The results were also consistent with the increased molar conductivity of nanocomposite‐gelled electrolytes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 47–53, 2008     

Performance of gelled-type dye-sensitized solar cells associated with glass transition temperature of the gelatinizing polymers

Poly(methyl acrylate) (PMA), poly(vinyl acetate) (PVAc) and poly(n-isopropylacrylamide) (PNIPAAm) with their respective T_g of 6, 32, and 145 °C were employed to gel the LiI/I₂/tertiary butylpyridine electrolyte system for preparation of the gelled-type dye-sensitized solar cells (DSSC). The light-to-electricity conversion efficiencies of DSSCs gelled by PMA, PVAc, and PNIPAAm were 7.17%, 5.62%, and 3.17%, respectively under simulated AM 1.5 sunlight irradiation, implying that utilizing the polymer of lower T_g to gel the electrolytes leaded to better performance of the DSSCs. Their short-circuit current density and IPCE also showed the similar trend. Electrochemical impedance spectroscopy of the gelled DSSCs revealed that utilizing the polymer of lower T_g resulted in lower impedance associated with the Nernstian diffusion within the electrolytes. The results were consistent with the observation that the molar conductivity of gelled electrolytes was higher as the polymer of lower T_g was applied, which can be justified by Vogel-Tammann-Fulcher (VTF) equation.     

一种新型聚合物电解质的研制

合成了聚 (甲基丙烯酸甲酯 丙烯腈 甲基丙烯酸锂 ) (简记为PMAML)新型聚合物电解质基质材料 ,把它与聚偏氟乙烯 (PVDF)共混制备了凝胶化的聚合物电解质 .通过核磁共振波谱确定了PMAML的组份含量 ,并用扫描电镜观察了该聚合物基质膜的表面形貌 .利用交流阻抗技术测试了其电导率 ,室温下电导率可达2 5× 10 - 3S·cm- 1 .采用线性伏安扫描方法研究了该聚合物电解质的电化学稳定性 ,其电化学稳定窗口为4 5V .通过受限扩散实验测得电解质中离子的扩散系数为 8 12× 10 - 7cm2 ·s- 1 .组装的聚合物电解质锂离子电池首次充放电效率为 89% ,前 5次循环容量基本稳定 .     

P(VdF-HFP)-基离子液体复合聚合物电解质的阴极稳定性及热稳定性

以聚偏氟乙烯-六氟丙烯P(VdF-HFP)聚合物为基体, 制备了含离子液体1-甲基-3-乙基咪唑六氟磷酸盐(EMIPF6)、用于锂离子电池的离子液体复合聚合物电解质[P(VdF-HFP)/LiPF₆/EMIPF₆/EC(碳酸乙烯酯)-PC(碳酸丙烯酯)]. 采用热重分析法以及燃烧实验测试了复合聚合物电解质的热稳定性. 离子电导率测试表明, 离子液体的存在显著改善了复合聚合物电解质的离子传输; 循环伏安测试表明, 添加剂EC和PC的加入提高了复合电解质的阴极稳定性, 制得的离子液体复合聚合物电解质在0.3-4.3 V 电压范围内稳定存在. Li₄Ti₅O₁₂ 和LiCoO₂为电极材料、P(VdF-HFP)/LiPF₆/EMIPF₆/EC-PC 为电解质的半电池表现出优良的循环性能, 0.1C充放电倍率下, Li/LiCoO₂和Li/Li₄Ti₅O₁₂半电池的可逆容量分别为130和144 mAh·g^-1. 但EC、PC在一定程度上降低了离子液体复合聚合物电解质的热稳定性.     

新型锂离子电池电解液添加剂的合成与应用

设计并合成了一系列基于苯环和环状碳酸酯的有机分子双(2,3-环碳酸甘油酯)对苯二甲酸酯、三(2,3-环碳酸甘油酯)均苯三甲酸酯和四(2,3-环碳酸甘油酯)均苯四甲酸酯,采用倍率测试、恒流充放电测试、交流阻抗测试和扫描电子显微镜测试等手段研究了这些添加剂对锂离子电池性能的影响.通过对循环20周前后球化石墨电极形貌的对比,发现含均苯四甲酸酯和均苯三甲酸酯的电解液球化石墨电极表面相对于空白电解液可形成一层致密而稳定的固体电解质中间相膜(SEI),从而优化电极-电解液的界面性能,且电池电阻增加较小;在测试电池的倍率性能时发现,均苯四甲酸酯的加入可以改善电池的倍率性能,而对苯二甲酸酯的加入则未能改善电池的循环性能.     

Preparation and Evaluation of Some Terpolymers as Lube Oil Additives

In the present work, some polymeric additives were prepared to use as viscosity index improvers and pour point depressants for lube oil via copolymerization of hexadecylacrylate and dodecylacrylate with styrene. Structure of the prepared compounds was confirmed by infrared spectroscopy and nuclear magnetic resonance. The molecular weights of the prepared copolymers were determined by using gel permeation chromatograph. The efficiency of the prepared terpolymers as viscosity index improvers and pour point depressants for lube oil was investigation. It was found that all the prepared terpolymers are effective as viscosity index improvers and pour point depressants. The viscosity index of the prepared terpolymers increases with increasing the concentration of the additives and increases by increasing the percentage of hexadecylacrylate until 70%. The best result for viscosity index of the prepared terpolymers is when the percentage of styrene is 10%. The pour point of the prepared compound decreases with decreasing concentration of additive used.