Binding of uranyl ion by 2,2′-dihydroxyazobenzene attached to crosslinked polystyrenes covered with highly populated quaternary ammonium cations

2,2′-Dihydroxyazobenzene (DHAB) derivatives were attached to poly(chloromethylstyrene-co-divinylbenzene) (PCD) because of the high affinity of DHAB for uranyl ion. Chloromethyl groups of PCD were converted to quaternary ammonium ions by treating them with tertiary amines. Two strategies were adopted to improve the uranyl-binding ability of the immobilized DHAB: (1) the creation of a highly cationic microenvironment around the DHAB moieties and (2) the introduction of electron-withdrawing groups to DHAB. Capacity of the resins for uranyl uptake was measured, revealing that about 10 to 46 mg of uranium could be complexed to 1 g of the resins. Formation constants (K_f) for the uranyl complexes of the resins were determined. In the presence of ≥0.02 M bicarbonate ion at pH 8.02, log K_f values of 14.3 to 15.8 were obtained. Uranium extraction from seawater with two kinds of resins prepared in this study was carried out on the east coast of the Korean peninsula. The amount of uranium extracted from seawater was up to 150 μg/g resin. Thus, the uranium-extracting capability of the DHAB-containing polystyrene resins was improved significantly by the structural modifications. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4117–4125, 1999     

Solid state 15N NMR study of 15N enriched melamine-formaldehyde resins

Molecular dynamics and structure of uncured and cured melamine-formaldehyde resins isotopically ¹⁵N enriched at amine sites were studied by solid-state ¹⁵N nuclear magnetic resonance (NMR). Spectra recorded with direct (DP) and cross-polarization (CP) pulse sequences reflect two motionally different regions arising from similar chemical structures. DP spectra of uncured resins at higher temperatures have narrow lines and the detection of slightly different structural units is possible. With increasing crosslinking resonances broaden and overlap and the direct detection of individual signals in cured resins is not possible. On the basis of variable contact time, variable spinning speed, and interrupted decoupling experiments three protonated and one nonprotonated group of signals are identified in the CP spectra for all samples. Short polarization-transfer rates, T_NH, for nonprotonated nitrogen in uncured and lightly cured samples reveal more effective hydrogen bonding in viscous and rubber-like resins compared to the highly cured rigid resins. The rigid portions of the resins exhibit longer T₁ and short T_1ρ relaxation times, while the shorter T₁ times and longer T_1ρ times are associated with the more mobile portion of samples. ©1995 John Wiley & Sons, Inc.     

Continuous and gradual photo-activation methods: influence on degree of conversion and crosslink density of composite resins

Thermal properties and degree of conversion (DC%) of two composite resins (microhybrid and nanocomposite) and two photo-activation methods (continuous and gradual) displayed by the light-emitting diode (LED) light-curing units (LCUs) were investigated in this study. Differential scanning calorimetry (DSC) thermal analysis technique was used to investigate the glass transition temperature (T _g) and degradation temperature. The DC% was determined by Fourier transform infrared spectroscopy (FT-IR). The results showed that the microhybrid composite resin presented the highest T _g and degradation temperature values, i.e., the best thermal stability. Gradual photo-activation methods showed higher or similar T _g and degradation temperature values when compared to continuous method. The Elipar Freelight 2^TM LCU showed the lowest T _g values. With respect to the DC%, the photo-activation method did not influence the final conversion of composite resins. However, Elipar Freelight 2^TM LCU and microhybrid resin showed the lowest DC% values. Thus, the presented results suggest that gradual method photo-activation with LED LCUs provides adequate degree of conversion without promoting changes in the polymer chain of composite resins. However, the thermal properties and final conversion of composite resins can be influenced by the kind of composite resin and LCU.     

Novel polystyryl resins for size exclusion chromatography

New size exclusion chromatography (SEC) resins based on a crosslinker having independent vinyl groups have been produced and compared with SEC resins based on divinylbenzene-55 (DVB). 1,2-Bis(p-vinylphenyl)ethane (p,p-BVPE) and its meta-isomers were suspension-copolymerized with p-methylstyrene in the presence of different porogens to give particles of about 5 μm average diameter. The porous particles were slurry-packed into stainless steel columns for SEC evaluation. Calibration curves were obtained using narrow disperse polystyrene standards with molecular weights ranging from 580 to 3,040,000. The calibration curves for the new BVPE resins covered wider useful molecular weight ranges than those for comparable divinylbenzene resins. Particle size, surface morphology and the properties of pores were studied using a Coulter Multisizer II, scanning electron microscopy, nitrogen adsorption, and mercury porosimetry. © 1994 John Wiley & Sons, Inc.     

Binding of uranyl ion by 2,2′-dihydroxyazobenzene attached to a partially chloromethylated polystyrene

A 2,2′-dihydroxyazobenzene (DHAB) derivative was attached to a chloromethylated cross-linked polystyrene derivative in view of high affinity of DHAB for uranyl ion. Chloromethyl groups of the resin were converted to quaternary ammonium ions by treating with tertiary amines. Capacity of the resins for uranyl-uptake was measured, revealing that about 20 mg of uranium can be complexed to 1 g of the resins. Formation constants (K_f) for uranyl complexes of the resins were determined. In the presence of >0.1 M bicarbonate ion at pH 8.10, log K_f of about 15 was obtained. As bicarbonate concentration was lowered, K_f decreased considerably. Degrees of uranyl-uptake from rapidly flowing uranyl solutions were measured, and the results suggested that rate of uranyl-uptake may not impose a major barrier to application of the resins in uranium extraction from seawater. Uranium extraction from seawater with the resins was carried out on the east coast of Korean peninsula. The amount of uranium extracted from seawater was about 10 µg/g resin. This is not satisfactory for economical processes of uranium recovery from seawater. Results of the present study, however, suggested that modification of the DHAB-containing resins can improve uranyl-binding ability, probably leading to economical recovery of uranium from seawater. In addition, simulation of uranyl-binding processes in seawater with the laboratory procedures developed in this study was satisfactory. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3169–3177, 1999     

Preparation and properties of modified bismaleimide resins by novel bismaleimide containing 1,3,4‐oxadiazole

Bismaleimide (BMI) resin is a high‐performance thermosetting polymer, but its inherent brittleness hinder a broader range of application. Therefore, it has aroused wide concern to improve the toughness of BMI resins without scarification of their thermal stability. This paper reported some studies on modified BMI resins based on diallyl bisphenol A, novel BMI monomers, e.g. 2‐[3‐(4‐maleimidophenoxy)phenyl]‐5‐(4‐maleimidophenyl)‐1,3,4‐oxadiazole (m‐Mioxd) or 2‐[4‐(4‐maleimidophenoxy)phenyl]‐5‐(4‐maleimidophenyl)‐1,3,4‐ oxadiazole (p‐Mioxd) in different proportions (0.87:1, 1:1, 1.2:1; mol/mol). The curing mechanism and kinetics of the copolymerized systems were investigated by differential scanning calorimetry and Fourier transform infrared spectroscopy. Thermogravimetric analysis was applied to study the thermal properties of the cured resins, and the results indicated that the modified resins had excellent thermal stability with high residual weight percentage at 700°C (>50%), temperatures for 5% weight loss around 400°C. Besides, N,N′‐4,4′‐bismaleimidodiphenylmethylene and O,O′‐diallyl bisphenol A resin blends were modified by m‐Mioxd and p‐Mioxd, respectively. We investigated the effects of mole concentration of m‐Mioxd or p‐Mioxd on the curing process, mechanical properties, fracture toughness, and heat resistance of the modified resins. The results revealed that the introduction of m‐Mioxd and p‐Mioxd could improve the impact property of the modified BMI resins. When their proportion was 0.07, the impact strength increased 123.8% and 108.3%, respectively. The novel chain‐extended BMIs could reduce the crosslink density of cured resins and improve the brittleness effectively. Copyright © 2015 John Wiley & Sons, Ltd.     

Hydrodynamic Behavior of Epoxy and Phenol-Formaldehyde Oligomers in Solution during Thermal Precondensation

The concentration dependences of the relative viscosity of epoxy-4,4'-isopropylidenediphenol (Epikot 1009, E-05) and phenol-formaldehyde (DFFr) resins in Cellosolve solutions in the concentration range c = 5-60%, as well as the kinetics of thermal precondensation of a mixture of E-05 and DPFr resins in solution at molar ratios N ₁/N ₂ = 0.6-1.5, were studied by the method of capillary viscometry. The cluster structure of the surface of coatings on the metal sheet formed by cross-linked epoxy-phenol polymer in various kinetic stages of precondensation of the mixture of E-05 and DFFr resins in solution was studied by electron microscopy with gold decoration. The optimal concentrations of resins in solution and the precondensation kinetics of oligomer mixtures essential for formulating the compounds were calculated.     

Phenol‐urea‐formaldehyde cocondensed resol resins: Their synthesis,curing kinetics,and network properties

Several phenol‐urea‐formaldehyde (PUF) cocondensed resol resins were synthesized by different procedures. The curing kinetics and network properties of these PUF resins were examined by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). A kinetic study indicated that the activation energy values of PUF resins are generally higher than those of phenol‐formaldehyde (PF) resins during curing processes, but the curing rates of PUF resins are faster than those of PF resins. The pH values of PUF systems have a significant influence on the rate constants, although they affect the activation energy very slightly. Moreover, the dependence of activation energy on the conversion showed that there are more individual reactions with different activation energies occurring during the curing processes in PUF resins than in PF resins. The decomposition of methylene ether bridges to form methylene bridges probably occurs at high temperature in PUF resins. DMTA data indicated that the network rigidity of PUF resins is slightly lower than that of PF resin. The gel point and T_{tan δ2} transition measured by DMTA were consistent with the kinetic results obtained from the DSC data, but they were also related to the physical and mechanical properties of the network, especially with regard to the T_{tan δ2} transition. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1929–1938, 2003     

Etherification of glycerol with tert-butyl alcohol catalysed by ion-exchange resins

The reaction of glycerol with tert-butyl alcohol in the liquid phase on acid Amberlyst-type ion-exchange resins was studied. The influence of temperature, mole ratio n(TBA)/n(G), water and swelling of gel, and macroreticular type of polymer catalysts on etherification reaction was investigated. The most favourable reaction temperature is 75°C. The conversion of glycerol and yield of glycerol tert-butyl ethers has increased with the mole ratio n(TBA)/n(G). Dry form of macroreticular catalysts provided the best results. Etherification reaction of glycerol with isobutylene in non-aqueous conditions gives the highest yield of desired ethers. The influence of water was studied. The gel forms of ion-exchange resins have very low catalytic activity. It can be concluded that water has an inhibition effect on ion-exchange resins. By comparing the gel and macroreticular forms of Amberlyst ion-exchange resins it can be concluded that very acid forms of macroreticular ion-exchange resins with a high degree of crosslinking are more active catalysts for the studied reaction due to their pores which are sufficiently large so that the voluminous tert-butyl ethers of glycerol can be formed. It was estimated that tert-butyl alcohol as tert-butylation agent is not suitable for etherification of glycerol with the formation of di-and triethers.     

Acid–base Properties of Ion-exchange Resins. Dissociation and Swelling of Resin Copolymers of Methacrylic Acid,Methyl Methacrylate,Divinylbenzene, and Ethylvinylbenzene

The dissociation, capacity, swelling, and water content of crosslinked methacrylic acid—methyl methacrylate resins have been measured. Resins were prepared with different degrees of crosslinking for the same carboxylate content, and vice versa. The ionic strength of the external solution was also varied, and the behavior of commercial resins compared with that of the laboratory resins. Potentiometric titration curves were obtained, and curves were also obtained by back-titration of the salt form of the resins with acid. The capacities showed that almost all carboxyl groups are accessible in resins containing 2.5% or 4.0% divinylbenzene, but not in those containing 8% or 12%. For these highly crosslinked resins the back-titration curves differed from the forward curves. Apparent dissociation constants pK′_a = pH + n log [(1 ? α)/α] decreased with increased ionic strength, increased with increased crosslinking, and showed no trend with carboxylate content. Swelling is decreased by increased salt concentration, particularly for lightly crosslinked resins. Maximum swelling is achieved at about 80% dissociation. The reciprocal of the swollen volume is proportional to the per cent of divinylbenzene. Commercial resins showed much lower swelling than laboratory prepared resins ostensibly having the same composition. The Gibbs-Donnan theory of resin dissociation was applied to calculate the intrinsic dissociation constant (pK′₀). Assuming a model of randomly kinked chains dissolved in the sorbed solution, good agreement with the expected value of 4.85 was found (calcd. pK′₀ = 4.81 = 0.14), except for the most highly crosslinked resins. For polyampholyte resins, agreement was found by using a model having a uniform potential distribution throughout the resin (pK′₀ = 4.9).     

Evaluation of the Biocidal Capacity of Hypercrosslinked Resins Containing Dithiocarbamate Groups

Summary: In this study we report both the development of dithiocarbamate resins from the commercial hypercrosslinked resin MN-250 and the evaluation of the biocidal capacity of this material against E. coli ATCC25922 suspensions. The preparation of dithiocarbamate resins followed a synthetic pathway based on nitration of resins, reduction of nitro groups and reaction with CS₂ in an alkaline medium. The biocidal capacity was evaluated by means of elution of E. coli suspensions (10³–10⁷ cells/mL) through columns containing the resin and plating on LB nutrient medium solidified with Bacto agar. We can conclude that hypercrosslinked resins with dithiocarbamate groups have potential biocidal action.     

Polymer-supported phosphines: Reactivity of pendant and crosslink groups

Two groups of phosphine-containing resins were prepared by bead copolymerization. In one the phosphine residues were introduced as pendant groups with p-styryldiphenylphosphine, whereas in the other the phosphine residues were located specifically at crosslinked points with bis(p-styryl)phenylphosphine. Both groups of resins were used to convert alcohols to alkyl chlorides in the presence of carbon tetrachloride and benzaldyhyde to benzal chloride and β,β-dichlorostyrene. In the first reaction an increase in the crosslink ratio of the support reduced the reactivity of the resins, although both octanol and octadecanol substrates behaved similarly. No clear difference emerged between resins with pendant phosphine groups and those located on crosslinks and the absence of a strong substrate size effect or substrate selectivity with both series of resins was apparent. The production of benzal chloride and β,β-dichlorostyrene requires interaction of two phosphine residues to generate the reactive intermediate, and inhibition of phosphine–phosphine interactions in these highly crosslinked networks does indeed inhibit this reaction. Again both series of resins behaved similarly. Among the possible routes by which PPh₃/CCl₄ converts alcohols to chlorides one involving phosphine-phosphine interactions must also be inhibited in these supported systems.     

Effect of irradiation on AMP based resins for cesium separation from HNO3 feed solutions: batch and column studies

Three different resins containing ammonium molybdophosphate (AMP), viz. PMMA (polymethylmethacrylate) resin, composite AMP resin and ALIX (a bisphenol based resin), were evaluated for their irradiation stability. The studies included batch as well as column studies and were carried out for cesium uptake behaviour at 3 M acidity. The resin beads were irradiated to varying dose viz., 0 MRad, 10 MRad, 20 MRad, 50 MRad and 100 MRad. The time taken to attain equilibrium was rather long and about 2–5 h were found to be required for attaining equilibrium in batch studies. Batch Cs(I) uptake studies revealed no significant effect on the K _d values in case of the PMMA resin while in case of the composite resin and ALIX resin, a decrease in the K _d was observed as a function of irradiation dose. The resin capacity indicated contrasting behaviour with irradiation dose for the resins. Column runs have been carried out for the uptake of radio cesium using both unirradiated and irradiated resins using feed solutions containing 3 MHNO₃. The loading capacities of the resins were found to be proportional to their Cs loading capacities observed in batch studies. Study revealed that the composite AMP had the maximum and PMMA has the least loading capacity. Results of these studies show that these AMP based resins can be used for cesium separation from acidic nuclear waste.     

Ion exchange behaviour of polymeric zirconium cations

Summary Polymeric zirconium cations formed in weakly acid solution (pH2) are taken up strongly into macroporous cation exchange resins, while uptake into normal cation exchange resins (pore diameter about 1 nm) is low. Macroporous cation exchange resins loaded with polymeric Zr cations are shown to function as ligand exchange sorbents.

---

Ionenaustauschverhalten polymerer Zirkonium-Kationen (Kurze Mitt.)

Zusammenfassung Polymere Zirkonium-Kationen, die in schwach sauren Lösungen (pH2) vorliegen, werden von makroporösen Kationenaustauschern stark aufgenommen, während bei den üblichen Kationenaustauschern (mit Porengrößen von etwa 1 nm) nur geringe Aufnahme stattfindet. Makroporöse Kationenaustauscher die mit polymeren Zr-Kationen beladen sind fungieren als Liganden-Austauschsorbentien.

     

Synthesis and characterization of epoxy resins containing imine group and their curing processes with aromatic diamine

The epoxy resins containing imine bonding were prepared from hydroxyl substituted Schiff base monomers in two steps. At the first step, hydroxyl substituted Schiff base monomers were synthesized via condensation reaction. At the second step, epoxy resins were synthesized from the reaction between Schiff base monomers and epichlorohydrine (EPC). Then curing processes of epoxy resins were achieved by p-phenylenediamine compound. The structures of resulting compounds were confirmed by FT-IR, UV-Vis and ¹H-NMR. TG-DTA and DSC measurements were performed for thermal characterizations of the compounds. Chemical resistances of the cured epoxy-amine systems were determined for coating applications in acidic, alkaline and organic solvents. HCl (10%, aqueous solution), NaOH (10%, aqueous solution), DMSO, DMF, N-methylpyrrolidone, ethanol, THF and acetone were used for corrosion tests. Chemical resistance data of the synthesized epoxy resins demonstrated that they have good chemical resistance against various acid, alkaline and common organic solvents. Surface morphologies of epoxy resin and the cured epoxy resin were determined with scanning electron microscopy (SEM) measurements. Also, optical band gap (E_g) values of Schiff base monomers and epoxy resins were calculated from UV-Vis measurements.     

Synthesis of Davankov‐type hypercrosslinked resins using different isomer compositions of vinylbenzyl chloride monomer,and application in the solid‐phase extraction of polar compounds

Two different gel‐type resins have been prepared by suspension polymerization using 2 wt % divinylbenzene (DVB) with either p‐vinylbenzyl chloride (pVBC) or a mixture of VBC isomers (～ 70% m‐; ～ 30% p‐). Significant difference in the chlorine content was observed, which was attributed to a more favored hydrolysis process when p‐VBC was used. The presence of hydroxyl groups has been confirmed by elemental microanalytical data and solid‐state ¹³C cross‐polarization/magic angle spinning (CP‐MAS) nuclear magnetic resonance (NMR) spectra. Hypercrosslinked resins were prepared from both gel‐type precursors by treatment with FeCl₃ in 1,2‐dichloroethane (DCE) at 80 °C. The resultant resins showed differences in specific surface area and degree of hydrophilicity. The performance of the hypercrosslinked resins was evaluated in solid‐phase extraction (SPE) of polar compounds, and better results were obtained for the hypercrosslinked resin prepared from p‐VBC that combines a relatively high specific surface area (908 m² g^?1) and somewhat higher oxygen content (3.96 wt % O). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1718–1728, 2005     

Synthesis of thiol chelating resins and their adsorption properties toward heavy metal ions

A series of chelating resins, derived from a macroreticular styrene-divinylbenzene (2%) copolymer beads grafted with various poly(ethylene glycols) HO? (? CH₂? CH₂? O? )_n? H(n = 0, 4, 9, 13) and containing thiol groups as chelating functions, have been synthesized in a three-step reaction sequence. The structure of the functionalized resins was confirmed by IR spectrophotometry, elemental analysis, and differential scanning calorimetry. The complexation behavior of these thiol resins was investigated towards Hg(II), Cu(II), and Pb(II) ions in aqueous solution by a batch equilibration technique. The influence of pH on adsorption capacity was also examined. The adsorption values for metal ions' intake followed the order Hg(II) > Cu(II) > Pb(II). The affinity of these polymers towards Hg(II) ions was so high that the total mercury level in the liquid decreased from 20 ppm to below 10 ppb after 2 h of treatment. Polymers can be regenerated by washing with a solution of hydrochloric acid (6N) and 10% by weight of an aqueous solution of thiourea. © 1994 John Wiley & Sons, Inc.     

Preparation and Properties of Epoxy Resins Containing Quinazolone Rings

Epoxy resins containing quinazolone rings were synthesized and characterized. Epoxy resins were made by reacting bisquinazolone phenol or bisquinazoline with epichlorohydrin or the diglycidyl ether of Bisphenol A. These resins were analyzed by DSC, GPC, IR, and NMR. The electrical and mechanical properties of the cured resins were evaluated. They have glass transition temperature above 200°C and excellent thermal stability, and T_g increases in the order of o-, m-, p-substituted phenol groups.     

PHASE STRUCTURE AND PROPERTIES OF EPOXY RESIN MODIFIED BY POLYSILOXANE BEARING PENDANT AMINO GROUPS

Polysiloxane-modified epoxy resins were prepared through the reaction of epoxy resin with polydimethylsiloxanesbearing pendant N-(β-aminoethyl)-γ-aminopropyl groups. The morphology and properties of the cured epoxy resins modifiedby the polysiloxanes were investigated. It was found that the phase structure and properties of the cured epoxy resins dependmainly on the amino group content in the polydimethylsiloxane and the level of the modifier. The change of phase structurein the cured epoxy resin systems was responsible for the dramatic change in their mechanical and surface properties.     

Preparation and characterization of crosslinked poly(N,N‐diethylacrylamide‐co‐2‐hydroxyethyl methacrylate) resins and their application as support in solid‐phase peptide synthesis

Novel hydrophilic and thermosensitive poly(N,N‐diethylacrylamide‐co‐2‐hydroxyethyl methacrylate) resins were prepared by inverse suspension polymerization with N,N′‐methylenebis(acrylamide) as a crosslinker. The effects of chemical composition and degree of crosslinking on the polymerization were investigated. The polymer resins were characterized by elemental analysis, infrared spectroscopy, differential scanning calorimetry, and scanning electron microscopy. The thermosensitivity of the crosslinked resins was demonstrated by their lower critical swelling temperatures. The swelling and deswelling volume of the beads in water varied depending on the molar fraction of the N,N‐diethylacrylamide. These beads swelled extensively in a variety of common solvents. They had high loadings of functional hydroxyl groups and were used as supports in the solid‐phase synthesis of an oligopeptide. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1681–1690, 2003