Li3VO4-Li4SiO4-Li4GeO4赝三元系相图的研究

本文用差热分析法和高温、室温X射线衍射法对Li₃VO₄,Li₄SiO₄的相变过程,Li₃VO₄-Li₄SiO₄,Li₃O₄-Li-4GeO₄赝二元系相图以及Li₃VO₄-Li₄SiO₄-Li₄GeO₄赝三元系相图室温截面进行了研究。发现在Li₃VO₄-Li₄SiO₄,Li₃VO₄-Li₄GeO₄赝二元系中,由于Li₄SiO₄或Li₄GeO₄的加入而使Li₃VO₄的高温γ_II相稳定存在于室温,从而得到一种新的具有高电导率的锂离子导体。作者认为探寻使高温态稳定存在于室温的方法是探索新的离子导体研究中有效途径之一。 关键词：     

Li4SiO4-Li3VO4赝二元系和Li4GeO4-Li4SiO4-Li3VO4赝三元系中新的锂离子导体

本文在室温到300℃的温度范围内研究了Li₄SiO₄-Li₃VO₄和Li₄GeO₄-Li₄SiO₄-Li₃VO₄体系中的离子导电性,发现γ_II相固溶体Li_3+xV_1-xSi_xO₄是好的锂离子导体。所研究的成分中Li_3.3V_0.7Si_0.3O₄的离子电导率最高,室温下为1×10^-5Ω^-1·cm^-1,在42—192℃的电导激活能为0.36eV,电子电导率可以忽略,因而这是迄今所发现的最好的锂离子导体之一。粗略确定了Li₄GeO₄-Li₄SiO₄-Li₃VO₄三元系中电导率高的范围,发现在Li_3.5V_0.5Ge_0.5O₄中Si部分取代Ge可以使电导率进一步提高,Li_3.5V_0.5Ge_0.4Si_0.1O₄的室温电导率可达1.3×10^-5Ω^-1·cm^-1,电导激活能为0.40eV。 关键词：     

BaO-Li2O-B2O3三元系中BaB2O4-Li2B2O4和BaB2O4-Li2O截面相平衡关系的研究

本文用X射线和差热分析方法对BaO-Li₂O-B₂O₃三元系中的两个截面:BaB₂O₄-Li₂B₂O₄和BaB₂O₄-Li₂O作了研究。在BaB₂O₄-Li₂B₂O₄赝二元系中发现了一个新的化合物4BaB₂O₄·Li₂B₂O₄。化合物在930±3℃由包晶反应形成,并与Li₂B₂O₄形成共晶反应。共晶温度为797±3℃,共晶点组分为79mol％Li₂B₂O₄。在BaB₂O₄-Li₂O截面中也存在化合物4BaB₂O₄·Li₂B₂O₄,其包晶反应温度从930±3℃随Li₂O含量增加下降到908±3℃。在组分60mol％Li₂O处形成另一个新的化合物2BaB₂O₄·3Li₂O。该化合物在630±3℃也是由包晶反应形成,并与Li₂O和Li₂CO₃分别形成共晶反应,共晶温度分别为400±3℃和612±3℃。在BaB₂O₄-Li₂B₂O₄和BaB₂O₄-Li₂O体系中都没有观察到固溶体。用计算机程序分别对化合物4BaB₂O₄·Li₂B₂O₄和2BaB₂O₄·3Li₂O的X射线粉末衍射图案进行了指标化,其结果:4BaB₂O₄·Li₂B₂O₄的空间群为Pmma,a=13.033?,b=14.630?,c=4.247?,每个单胞包含两个化合式单位;2BaB₂O₄·3Li₂O的空间群为Pmmm,a=4.814?,b=9.897?,c=11.523?,每个单胞也含有两个化合式单位。 关键词：     

Li2SO4—Li2B2O4,Li2SO4—(NH4)2SO4赝二元系相图及离子导电性研究

本文用差热分析和X射线衍射方法对Li₂SO₄-Li₂B₂O₄和Li₂SO₄-[NH₄]₂SO₄两个赝二元系相图进行了研究。Li₂SO₄-Li₂B₂O₄是共晶体系,共晶温度为720℃ 关键词：     

Li2O-(LiCl)2-B2O3-Al2O3系统玻璃的Raman光谱研究

我们用Raman光谱研究了Li₂O(LiCl)₂B₂O₃-Al₂O₃系玻璃的结构,着重研究了Al₂O₃的影响。对于Li₂O-B₂O₃系玻璃,Li₂O含量增加使玻璃中存在的BO₃三角体转变为BO₄四面体, 关键词：     

Li2B4O7晶体及其熔体结构的拉曼光谱研究

采用高温原位拉曼光谱技术,研究了Li₂B₄O₇从常温至1 373 K温度范围内的拉曼光谱。在升温过程中,晶体的拉曼光谱出现展宽和红移现象,且强度降低。晶体熔化时,由2个[BO₄]和2个[BO₃]组成的[B₄O₉]环状结构转变成(B₃O₆)3- 六元环和[BO₃]结构,[BO₄]结构减少直至消失。基于密度泛函理论,计算了Li₂B₄O₇晶体的拉曼光谱,对其振动模式进行了分析归属。利用量子化学从头计算法计算了由[B₃O₆-BO₃]为基础相互连接形成的x(Li₂B₄O₇)(x=2, 3, …, 9)的环状团簇模型的拉曼光谱,对Li₂B₄O₇熔体的结构进行了模拟分析。计算结果表明Li₂B₄O₇熔体的阴离子基元为三个(B₃O₆-BO₃)组成的大三元环超级结构。     

Li1+xGe2-xAlxP3O12系统的相关系和电导

本文研究了Li_1+xGe_2-xAl_xP₃O₁₂系统的相组成和电导的关系。发现用LiGe₂P₃O₁₂作为基体化合物,通过离子置换可以得到好的锂离子导体。用Al³⁺置换LiGe₂P₃O₁₂中的Ge⁴⁺,在0关键词：     

Li2Mo2-xWxO6多晶材料的结构、电学性能与导电机理的研究

本文采用还原气氛制备导电性能优良的多晶多相陶瓷材料Li₂Mo_2-xW_xO₆(x=0,0.1,0.3),采用粉末X射线衍射分析、特征X射线能谱分析、红外光谱分析和电子自旋共振波谱分析等现代测试手段,得到样品的物相结构为Li₂Mo_1-xW_xO₄和MoO₂两相组成。W的掺入主要取代Mo进入Li₂ 关键词：     

Li3VO4-Li4TO4(T=Ge,Si)固溶体离子导体7Li的NMR研究

在150—573K温度范围内,研究了固溶体Li₃VO₄-Li₄TO₄(T=Ge,Si)系统不同成分的⁷Li的NMR谱。发现γ_II相固溶体室温⁷Li的NMR线宽和自旋晶格弛豫时间T₁的值都比Li₄GeO₄,Li₄SiO₄和Li₃VO₄小约一个数量级。这表明在γ_II相固溶体离子导体中,Li⁺离子运动有可能比固溶前有数量级增长。同时还发现⁷Li的电四极分裂伴线数随成分和温度而异,以及伴线强度百分比依赖于温度。这反映γ_II相的不同成分中,间隙Li⁺离子占有的不等价位置个数不同,而Li⁺离子在每个不等价位置上的占有率又随温度而变化。 关键词：     

非晶态锂离子导体B2O3-0.7Li2O-0.7LiCl-xAl2O3

木文研究了Al₂O₃对B₂O₃-0.7Li₂O-0.7LiCl非晶态的形成和电学性能的影响,我们发现:加入适量的Al₂O₃后,无需借助液氮骤冷技术,直接将熔体倾倒在室温下的紫铜板上就很容易形成大块非晶锂离子导体B₂O₃-0.7Li₂O-0.7LiCl-xAl₂O₃。Al₂O₃的加入使B₂O₃-0.7Li₂O-0.7LiCl的电导率有所降低,但在高温下不太明显,电导激活能略微升高,实验发现:Al₂O₃含量x=0.03是较合适的剂量,较容易形成大块非晶态,对电导率的影响也不大。 关键词：     

Crystallization kinetics of Li2O-PbO-V2O5 glasses

Lead vanadate glasses of the system 5Li₂O−(45−x) PbO−(50+x) V₂O₅, with x=0, 5, 10, and 15 mol% have been prepared and studied by differential scanning calorimetry (DSC). The crystallization kinetics of the glasses were investigated under non-isothermal conditions applying the formal theory of transformations for heterogeneous nucleation to the experimental data obtained by DSC using continuous-heating techniques. In addition, from dependence of the glass-transition temperature (T_g) on the heating rate, the activation energy for the glass transition was derived. Similarly the activation energy of the crystallization process was determined and the crystallization mechanism was characterized. The results reveal the increase of the activation energy for glass transition which was attributed to the increase in the rigidity, the cross-link density and the packing density of these glasses. The phases into which the glass crystallizes have been identified by X-ray diffraction. Diffractograms of the transformed material indicate the presence of microcrystallites of Li_0.30V₂O₅, Li_0.67O₅V₂, LiV₆O₁₅, Li₄O₄Pb, and O₇Pb₂V₂ in a remaining amorphous matrix.     

Structure and physical properties of Li4Ti5O12 synthesized at deoxidization atmosphere

Powders of spinel Li₄Ti₅O₁₂ (LTO) were successfully synthesized at reducing conditions by solid-state method. The structure and physical properties of Li₄Ti₅O₁₂ were examined by X-ray diffraction (XRD), Raman spectroscopy, scanning electronic microscopy (SEM), and differential capacitance, respectively. XRD shows that both samples are single-phase spinel compounds. LTO synthesized in Ar/H₂(8% mol) has a larger lattice parameter than that in Ar. SEM indicates that all of the prepared powders have the uniform, nearly cubic structure morphology with narrow size distribution in the range of 200–300 nm. Raman spectra indicate that the Raman bands corresponding to the Ti–O vibration has a blue shift from 674 to 680 cm⁻¹ due to the few H₂ in the synthesized condition, indicating that there is very few oxygen vacancies in the Li₄Ti₅O₁₂ synthesized under Ar/H₂ (8% mol). The dQ/dV vs. voltage plots reveals the redox potentials for the synthesized Li₄Ti₅O₁₂-negative electrode materials.     

Electrochemical behavior of nanostructured LiV3O8 in aqueous LiNO3 solution

Despite the large number of studies on the electrochemical behavior of LiV₃O₈ as a cathode material in nonaqueous lithium ion batteries, little information is available about the electrochemical behavior of LiV₃O₈ as an anode material in aqueous rechargeable lithium batteries. In this work, nanostructured LiV₃O₈ is successfully prepared using a low-temperature solid-state method. The electrochemical properties of the LiV₃O₈ electrode in 1 M, 5 M, and saturated LiNO₃ aqueous electrolytes have been characterized by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge/discharge experiments. The results show that LiV₃O₈ electrode in saturated LiNO₃ electrolyte exhibits good electrochemical performance in terms of specific capacity and electrochemical cycling performance. LiV₃O₈ electrode can be reversibly cycled in saturated LiNO₃ aqueous electrolyte for 300 cycles at a rate of 0.5 C (300 mA g⁻¹ is assumed to be 1 C rate) with impressive specific capacities.     

Thermochemistry of the high and ambient temperature lithium vanadium bronze phases LixV2O5

The enthalpies of formation of a series of high and low temperature phases in the ternary oxide system Li_xV₂O₅ have been determined by solution calorimetry. Samples of the former, α-Li_0.04V₂O₅, β-Li_0.30V₂O₅, β'-Li_0.48V₂O₅ and γ-LiV₂O₅, were prepared by solid state reaction at 650°C. The ambient temperature materials Li_0.1V₂O₅(I), Li_0.45V₂O₅(II) and Li_1.03V₂O₅(III) were prepared by n-butyl lithiation in hexane. The thermochemistries of the two classes of material were examined and related to structural features and to the observed behaviour of V₂O₅ as a battery cathode material in lithium cells.     

Synthesis and characterization of lithium manganese oxides with core-shell Li4Mn5O12@Li2MnO3 structure as lithium battery electrode materials

By a facile LiNO₃ flux method, lithium manganese oxide composites (xLi₄Mn₅O₁₂? yLi₂MnO₃) were synthesized using a hierarchical organization precursor of manganese dioxide. Li₄Mn₅O₁₂ and Li₂MnO₃ have spinel and rocksalt structures, respectively. The lithiation and structural transformation from the precursor to the composites occurred topotactically from exterior toward interior in the precursor particle with the increase of reaction time, and the composites had core-shell spinel@rocksalt structures in addition to the original hierarchical core-shell organization. The electrochemical measurements at 50 °C after 50 cycles confirmed that a typical spinel@rocksalt cathode had higher capacity retention (87.1%) than that with the composition close to the stoichiometric spinel (64.6%), indicating the Li₂MnO₃ shell can improve cycling stability for the composite electrode at elevated temperature.     

Nanophase ZnV2O4 as stable and high capacity Li insertion electrode for Li-ion battery

Spinel ZnV₂O₄ nanoparticles are synthesized by a hydrothermal method and its properties are characterized using XRD, SEM, TEM, and electrochemical test. The structural and morphological characterizations show that ZnV₂O₄ sample has high purity and well crystallization with crystal size less than 20 nm. The as prepared electrode shows stable capacity over 660 mAh g⁻¹ in the voltage range of 0.01–3.0 V at 50 mA g⁻¹. The reaction mechanism with lithium ion is also investigated through ex-XRD and -TEM. It shows that the pristine ZnV₂O₄ is transformed to isostructural spinel Li_xV₂O₄ (x close to 7.6) and metal Zn phase during the first lithiation process. Then the spinel Li_xV₂O₄ seems to perform a topotactic intercalation reaction mechanism and that the in-situ formed Li_xV₂O₄ can still keep its spinel matrix while allowing more than 5.7 lithium reversibly into/out over 50 cycles.     

Low-temperature synthesis and growth of superparamagnetic Zn0.5Ni0.5Fe2O4 nanosized particles

Mono-disperse spinel Ni_0.5Zn_0.5Fe₂O₄ nanosized particles have been synthesized via a hydrothermal method at low temperature. X-ray diffraction (XRD), transmission electron microscope (TEM) and high-resolution transmission electron microscope (HRTEM) analysis indicated that the synthesized nanocrystals were of pure cubic spinel structure with the size about 6-20 nm. The activation energy of grain growth is 35.06 kJ/mol experimented by the Arrhenius equation. A primary experimental model was put forward to shed light on the growth mechanism of crystallined spinel Ni-Zn ferrite nanosized particles under hydrothermal conditions. The magnetic measurements shows that the prepared Ni_0.5Zn_0.5Fe₂O₄ nanoparticle possess good superparamagnetic behavior.     

Lithium insertion into Co3O4: A preliminary investigation

Lithium has been inserted into the spinel Co₃O₄ both chemically and electrochemically. During lithiation the tetrahedral A-site Co²⁺ cations are displaced into neighbouring empty octahedral sites: the incoming Li⁺ ions occupy the remaining interstitial octahedra of the spinel structure to produce the partially ordered rocksalt compound LiCo₃O₄. The octahedral B-site cations of the A[B₂]X₄ spinel are unperturbed by this reaction: the oxide lattice expands by 8.6%. Lithium analyses and powder X-ray diffraction spectra indicate that further lithiation is possible. However, it is demonstrated that a fast lithiation in excess of LiCo₃O₄ is followed by a slow extrusion of B-site cobalt at 50°C until all the Li on the 8a sites has moved to the octahedral vacancies thus created.