Sodium and silver phosphate glasses doped with chlorides of Fe,Mn and Zn

A number of samples of sodium and silver phosphate glasses doped with various compositions of some transition metals viz. iron, manganese and zinc chlorides alongwith undoped samples of sodium and silver phosphate glasses were synthesized and characterized by X-ray diffraction, IR spectral, electrical conductivity and differential scanning calorimetry (DSC). The glass transition temperature (T _g) and crystallization temperature (T _c) values obtained from DSC curves were found to increase with increasing concentration of the dopant Fe/Mn/Zn chlorides in both sodium and silver phosphate glasses and the following sequence is observed: T _g(–FeCl₃)>T _g(–MnCl₂)>T _g(–ZnCl₂) T _c(–FeCl₃)>T _c(–MnCl₂)>T _c(–ZnCl₂) The increase in T _g and T _c values indicate enhanced chemical durability of the doped glasses. The electrical conductivity values and the results of FTIR spectral studies have been correlated with the structural changes in the glass matrix by the addition of different transition metal cations as dopants.     

Excess Molar Volume and Viscosity of Isobutyric Acid + Water Binary Mixtures Near and Far Away from the Critical Temperature

The excess molar volume V^E, shear viscosity deviation Δη and excess Gibbs energy of activation ΔG^∗E of viscous flow have been investigated by using density (ρ) and shear viscosity (η) measurements for isobutyric acid + water (IBA+W) mixtures over the entire range of mole fractions at five different temperatures, both near and close to the critical temperature (2.055K ≤ (T−T_c)≤ 13.055K). The results were also fitted with the Redlich–Kister equation. This system exhibited very large negative values of V^E and very large positive values of Δη due to increased hydrogen bonding interactions and correlation length between unlike molecules in the critical region and to very large differences between the molar volumes of the pure components at low temperatures. The activation parameters ΔH^∗ and ΔS^∗ have been also calculated and show that the critical region has an important effect on the volumetric properties.     

Amino acids in aqueous solution. Effect of molecular structure and temperature on thermodynamics of dissolution

The enthalpies of dissolution of glycine (Gly) and L-α-alanine (Ala) in water at 288.15–318.15 K were measured. The results were compared with the earlier obtained data for L-α-phenylalanine (Phe) and L-α-histidine (His). The standard enthalpies of dissolution (Δ_soln H ₀) and differences (ΔC _p ⁰ ) between the limiting partial molar heat capacity of the amino acids in solution and the heat capacity of the amino acids in the crystalline state were calculated in the temperature interval 273–373 K. Changes in the entropy of dissolution (ΔΔ_soln S ₀) and reduced Gibbs energy [Δ (Δ_soln G ₀/T)] in the temperature interval from 273 to 373 K were determined from the known thermodynamic relationships. The ΔC _p ⁰ value is negative for hydrophilic glycine and positive for other amino acids. The ΔΔ_soln S ⁰ values increase with an increase in the hydrophobicity of the amino acids. The Δ(Δ_soln G ₀/T) values become more negative in the order Ala, Phe, Gly, His. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 4, pp. 711–714, April, 2007.     

Thermal characterization of montmorillonite clays saturated with various cations

Emanation thermal analysis (ETA), thermogravimetry and high temperature XRD were used to characterize the thermal behavior during dehydration of natural Na montmorillonite (Upton Wyoming, USA) and homoionic montmorillonite (MMT) samples saturated with different cations, i.e. Li⁺, Cs⁺, NH₄⁺, Mg²⁺ and Al³⁺. ETA results characterized radon mobility and microstructure changes that accompanied the mass loss of the samples due to dehydration on heating in air. A collapse of interlayer space between the silicate sheets after water release from the MMT samples was characterized by a decrease of the radon release rate, ΔE. Decreases in c-axis basal spacing (d ₀₀₁) values determined from XRD patterns for the different montmorillonite samples follow the sequence:

Calculations of thermal functions of group-III nitrides

The change of thermal functions (ΔH ⁰(T), ΔS ⁰(T), ΔG ⁰(T)) and formation functions (ΔH _f⁰(T), ΔG _f⁰(T), K _f(T)) with temperature for gallium nitride and indium nitride have been formulated based on the reliable experimental data obtained by the use the same equipment in one laboratory.     

Heat capacities and thermodynamic functions of the tellurates(IV) of zinc and cadmium

The temperature dependencies of the molar heat capacities of ZnTeO₃, Zn₂Te₃O₈, CdTeO₃ and CdTe₂O₅ are determined. The experimental data are statistically processed using the least squares method to determine the parameters in the equations for the corresponding compounds: C_p,m=a+b(T/K)-c(T/K)^-2. These equations and the standard molar entropies are used to determine Δ^T₀S⁰_m, Δ^T_TH⁰_m and (Φ⁰_m+Δ^T,₀H⁰_m/T) for T'=298.15 K.     

Molar heat capacities and standard molar enthalpy of formation of 2-amino-5-methylpyridine

The heat capacities (C _p,m) of 2-amino-5-methylpyridine (AMP) were measured by a precision automated adiabatic calorimeter over the temperature range from 80 to 398 K. A solid-liquid phase transition was found in the range from 336 to 351 K with the peak heat capacity at 350.426 K. The melting temperature (T _m), the molar enthalpy (Δ_fus H _m⁰), and the molar entropy (Δ_fus S _m⁰) of fusion were determined to be 350.431±0.018 K, 18.108 kJ mol⁻¹ and 51.676 J K⁻¹ mol⁻¹, respectively. The mole fraction purity of the sample used was determined to be 0.99734 through the Van’t Hoff equation. The thermodynamic functions (H _T-H _298.15 and S _T-S _298.15) were calculated. The molar energy of combustion and the standard molar enthalpy of combustion were determined, ΔU _c(C₆H₈N₂,cr)= −3500.15±1.51 kJ mol⁻¹ and Δ_c H _m⁰ (C₆H₈N₂,cr)= −3502.64±1.51 kJ mol⁻¹, by means of a precision oxygen-bomb combustion calorimeter at T=298.15 K. The standard molar enthalpy of formation of the crystalline compound was derived, Δ_r H _m⁰ (C₆H₈N₂,cr)= −1.74±0.57 kJ mol⁻¹.     

Analysis of Thermodynamic Parameters of Glass Forming Polymeric Melts

The temperature dependence of the Gibbs free energy difference (ΔG), enthalpy difference (ΔH) and entropy difference (ΔS) between the undercooled meltand the corresponding equilibrium solid has been analysed for glass forming polymeric materials by calculating ΔG, ΔH and ΔS within the framework of the hole theory of liquids. The study is made for nine samples of glass forming polymeric melts; polypropylene oxide (PPO), polyamid-6 (PA-6), polytetramethylene oxide (PTMO), polyethylene oxide (PEO), polystyrene (PS), polypropylene (PP), polyethylene (PE), polyethylene terephthalate (PET) and polybutadiene (PB) and three simple organic liquids: tri-α-naphthyl benzene (tri-α-NB), o-terphenyl (o-ter) and phenyl salicylate (salol) in the entire temperature range T _m (melting temperature) to T _g (glass transition temperature). The ideal glass transition temperature (T _K) and the residual entropy (ΔS _R) of these samples have also been studied due to their important role in the study of the glass forming ability of materials. This revised version was published online in August 2006 with corrections to the Cover Date.     

Thermodynamic study on inclusion complex formation of riboflavin with hydroxypropyl-β-cyclodextrin in water

The inclusion complex formation of riboflavin (RF) with hydroxypropyl-β-cyclodextrin (HP-β-CD) in water was investigated by ¹H NMR, UV-vis spectroscopy, and solubility methods. A 1:1 stoichiometry and thermodynamic parameters of complex formation (K, Δ_c G ⁰, Δ_c H ⁰, and Δ_c S ⁰) were determined. Complexation was characterized by negative enthalpy and entropy changes due to prevalence of van der Waals interactions and hydrogen bonding between polar groups of the solutes. A partial insertion of RF into macrocyclic cavity was revealed on the basis of ¹H NMR data and molecular mechanics calculation. Location of benzene ring of RF molecule inside the hydrophobic cavity of HP-β-CD results in an increase of aqueous solubility of the former.     

Physicochemical constants as a factor determining the need for the derivatization of organic substances in analysis by gas chromatography

A criterion was proposed to estimate the necessity of the derivatization of organic substances for their determination on conventional nonpolar phases, based on such characteristic of analytes as molecular weight (M _r), normal boiling point (T _bp), and molar refraction (MR _D). All these constants can be presented as indices relative to nonpolar n-alkanes (similarly to chromatographic retention indices), I(M), I(T), and I(MR _D), which can be compared to each other as differences Δ_{T − M} = I(T) − I(M) and Δ_{T − M} R _D = I(T) − I(MR _D). Substances do not require derivatization if Δ_{T − M} < 400 and Δ_{T − M} R _D < 600, while at Δ_{T − M} > 600 and Δ_{T − MRD} > 800, derivatization is necessary.     

Competition of Viscosity Correlation Equations in Isobutyric Acid + Water Binary Mixtures Near and Far Away from the Critical Temperature

Shear viscosity deviations Δη have been investigated by using density (ρ) and kinematic viscosity (ν) measurements for isobutyric acid + water (IBA + W) mixtures over the entire range of mole fractions at atmospheric pressure and at two temperatures (301.15 and 315.15 K). This study extends the temperature range from the five other temperatures investigated in a previous work, 1.055 K≤(T−T _c )≤14.055 K, both far from and close to the critical temperature. This system exhibits very large positive values of Δη due to increased hydrogen bonding interactions and the correlation length between unlike molecules in the critical region, and to very large differences between the molar volumes of the pure components at low temperatures. The results were also fitted with the Redlich–Kister polynomial equations and the recently proposed Herráez correlation equation. Comparisons between the two models at different temperatures and number of parameters are discussed. We note that, in this system where the shear viscosity η as a function of mole fraction (x ₁) of IBA presents a maximum, experimental data are in agreement with the two correlation models when more than three parameters are employed, especially for temperatures far from the critical temperature.     

Thermodynamics of phenylated polyphenylene between 0 and 340 K

In an adiabatic vacuum calorimeter, the temperature dependence of the heat capacity C _p of phenylated polyphenylene and initial comonomer 1,4-bis(2,4,5-triphenylcyclopentadienone-3-yl)benzene was studied between 6 and 340 K with an uncertainty of about 0.2%. In a calorimeter with a static bomb and an isothermal shield their energies of combustion DUcomb were measured. From the experimental data, the thermodynamic functions C _p ⁰ (T), H ⁰(T)-H ⁰(0), S ⁰(T)-S⁰(0), G ⁰(T)-H ⁰(0) were calculated from 0 to 340 K, and standard enthalpies of combustion ΔH _comb ⁰ and thermodynamic parameters of formation-enthalpies ΔH _f ⁰, entropies ΔH _f ⁰, Gibbs functions ΔG _f ⁰ - of the substances studied were estimated at T=298.15 K at standard pressure. The results were used to calculate the thermodynamic characteristics (ΔH _f ⁰ ,ΔS _f ⁰, ΔG _f ⁰) of phenylated polyphenylene synthesis in the range from 0 to 340 K. This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermodynamic studies of the binding interactions of surfactin analogues to lipid vesicles Application of isothermal titration calorimetry

Isothermal titration calorimetry was applied for studying the binding interactions of cyclic and linear surfactins with different ionic charge (z= −2 and −3) and lipid chain length (n=14 and 18) to 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphatidyl-choline (POPC) vesicles in 10mMTris buffer at pH8.5with 150mMNaCl at 25°C. Surfactin analogues interacted spontaneously (ΔG _D ^w→b < 0) with POPC vesicles. The binding reactions were endothermic (ΔH _D ^w→b > 0) and entropy-driven process (ΔS _D ^w→b > 0). Moreover, significant differences in the binding constant values (K) ranging from 6.6·10³ to 9.6·10⁴ M⁻¹ show that cyclic structure and the increase of lipid chain length are favourable on the surfactin binding affinity to POPC vesicles, whereas the rise of the number of negative charges has an opposite effect.     

Low-temperature heat capacities and standard molar enthalpy of formation of aspirin

Molar heat capacities (C _p,m) of aspirin were precisely measured with a small sample precision automated adiabatic calorimeter over the temperature range from 78 to 383 K. No phase transition was observed in this temperature region. The polynomial function of C _p,m vs. T was established in the light of the low-temperature heat capacity measurements and least square fitting method. The corresponding function is as follows: for 78 K≤T≤383 K, C _p,m/J mol^-1 K^-1=19.086X ⁴+15.951X ³-5.2548X ²+90.192X+176.65, [X=(T-230.50/152.5)]. The thermodynamic functions on the base of the reference temperature of 298.15 K, {ΔH _T -ΔH _298.15} and {S _T-S _298.15}, were derived. Combustion energy of aspirin (Δ_c U _m) was determined by static bomb combustion calorimeter. Enthalpy of combustion (Δ_c H ^o _m) and enthalpy of formation (Δ_f H ^o _m) were derived through Δ_c U _m as - (3945.26±2.63) kJ mol^-1 and - (736.41±1.30) kJ mol^-1, respectively. This revised version was published online in July 2006 with corrections to the Cover Date.     

The thermodynamic properties of 2-ethylhexyl acrylate over the temperature range from <Emphasis Type="Italic">T</Emphasis> → 0 to 350 K

The temperature dependence of the heat capacity C _p ^o= f(T) 2 of 2-ethylhexyl acrylate was studied in an adiabatic vacuum calorimeter over the temperature range 6–350 K. Measurement errors were mainly of 0.2%. Glass formation and vitreous state parameters were determined. An isothermic shell calorimeter with a static bomb was used to measure the energy of combustion of 2-ethylhexyl acrylate. The experimental data were used to calculate the standard thermodynamic functions C _p ^o(T), H ^o(T)-H ^o(0), S ^o(T)-S ^o(0), and G ^o(T)-H ^o(0) of the compound in the vitreous and liquid states over the temperature range from T → 0 to 350 K, the standard enthalpies of combustion Δ_c H ^o, and the thermodynamic characteristics of formation Δ_f H ^o, Δ_f S ^o, and Δ_f G ^o at 298.15 K and p = 0.1 MPa.     

Saturated Vapor Pressure of Iridium(III) Acetylacetonate

The temperature dependency of the saturated vapor pressure of Ir(acac)₃ has been measured by the method of calibrated volume (MCV), the Knudsen method, the flow transpiration method, and the membrane method. The thermodynamic parameters of phase transition of a crystal to gas were calculated using each of these methods, and the following values of ΔH _T ⁰ (kJ mol⁻¹) and ΔS _T ⁰ (J mol⁻¹K⁻¹), respectively, were obtained: MCV: 101.59, 156.70; Knudsen: 130.54, 224.40; Flow transpiration: 129.34, 212.23; Membrane: 95.45, 149.44 Coprocessing of obtaining data (MCV, flow transportation method and Knudsen method) at temperature ranges 110−200°C as also conducted:ΔH _T ⁰ =127.9±2.1 (kJ mol⁻¹ ); ΔS _T ⁰ =215.2±5.0 (J mol⁻¹ K⁻¹ ). This revised version was published online in August 2006 with corrections to the Cover Date.     

Standard formation enthalpies for α-amino acids: L-serine,L-arginine,and L-tyrosine

The energies of combustion, Δ _c U ⁰, of three amino acids: L-serine (I), L-arginine (II) and L-tyrosine (III) in the crystalline state at 298.15 K were determined using a static-bomb isoperibolic calorimeter. From these data, the enthalpies of combustion, Δ _c H ⁰, and the enthalpies of formation, Δ _f H ⁰, are calculated. The Δ _f H ⁰ values are compared with the published data.     

Influence of MgO (CaO) on the structure of silicate-phosphate glasses

Thermal and structural properties of model silicate-phosphate glasses containing the different amounts of the glass network modifiers, i.e. Mg²⁺ and Ca²⁺ were studied. To explain the changes of the parameters characterizing the glass transition effect (T_g, Δc_p) and the crystallization process (T_c, ΔH) depending on the cations modifiers additions, analysis of the bonds and chemical interactions of atoms in the structure of glasses was used. ³¹P MAS-NMR spectra of SiO₂–P₂O₅–MgO(CaO)–K₂O glasses show that the phosphate complexes are mono- and diphosphate. It has been found that increasing amounts of Mg²⁺ or Ca²⁺ cations in the structure of glasses causes the reduction of the degree of polymerization of the phosphate framework (Q¹→Q⁰). The influence of increasing of modifiers in the structure of silicate- phosphate glasses on the number of non-bridging oxygens per SiO₄ tetrahedron and density of glasses was presented.     

Density and viscosity of magnesium sulphate in formamide + ethylene glycol mixed solvents

Densities (ρ) and viscosities (η) of different strengths of magnesium sulphate (MgSO₄) in varying proportions of formamide (FA) + ethylene glycol as mixed solvents were measured at room temperature. The experimental values of ρ and η were used to calculate the values of the apparent molar volume, (φ_1,), partial molar volume, (φ₁,^ℴ) at infinite dilution,A- andB-coefficients of the Jones-Dole equation and free energies of activation of viscous flow, (Δμ ₁ ^0* ) and (Δμ ₂ ^0* ), per mole of solvent and solute respectively. The behaviour of these parameters suggests strong ion-solvent interactions in these systems and also that MgSO₄ acts as structure-maker in FA + ethylene glycol mixed solvents.     

Thermodynamic properties of germanium and lead tellurites

The temperature dependence of the molar heat capacities of the tellurites PbTeO₃, Pb₂Te₃O₈ and Ge(TeO₃)₂ are determined. By statistical manipulation of the values obtained, the parameters in the equations for the corresponding compounds showing this dependence are determined using the least-squares method. These equations and the standard molar entropies are used to determine the thermodynamic functions Δ₀ ^T S _m ⁰ , Δ_T ^T H _m ⁰ and (Φ_m ⁰+Δ₀ ^T H _m ⁰/T) for T'=298.15 K.