Direct and simultaneous determination of copper and manganese in seawater with a multielement graphite furnace atomic absorption spectrometer

The direct and simultaneous determinations of Cu and Mn in seawater using a multielement graphite furnace atomic absorption spectrometer (Perkin-Elmer SIMAA6000) are described. Three kinds of chemical modifier (Mg(NO₃)₂, Pd(NO₃)₂ and a mixture of these) were tested. The matrix interferences were removed completely so that a simple calibration curve method could be used to determine Cu and Mn in seawater from the open ocean using Pd or a mixture of Pd and Mg as the chemical modifier. The relative standard deviations (RSDs) for the simultaneous determination of Cu and Mn in seawater from open ocean are 10% or less, and the detection limits were 0.07 μg 1⁻¹ for Cu and 0.10 μg 1⁻¹ for Mn, using Pd as the chemical modifier. The accuracy of the method is confirmed by analysis of four kinds of certified reference saline waters.     

Semi-permanent lutetium modifier for the determination of beryllium in urine by electrothermal atomic absorption spectrometry

The determination of beryllium using electrothermal atomic absorption spectrometry with deuterium background correction in the presence of various isomorphous metals and Mg(NO₃)₂ was studied. While, Eu, Ir and Sm had no effect on the transient signals, the addition of Lu and Mg(NO₃)₂ improved the sensitivity of the beryllium signal with respect to that obtained in the absence of modifier. Although, Mg(NO₃)₂ has improved the signal with respect to its sensitivity, it also increased the tail and the background (BG) signals, specially when urine samples are under study. Whereas, when Lu was used the analytical signal is virtually free of BG interference indicating that the urine matrix interference was almost eliminated. Besides, the addition of 6 μg of Lu ensured that the signals were effectively constant for five firings following the furnace program, which included: three drying, and the pyrolysis, atomization, cleaning and cooling steps. The effect of some components, likely to interfere in the accurate determination of beryllium (such as: Al, Ca, Cl, Co, Cr, Fe, Mg and Mn) were investigated. At the physiological levels, most of these elements had no effect, except in the case of chloride when Mg(NO₃)₂ was used as modifier. In this case, the tolerance limit was of 3000 mg Cl⁻ l⁻¹. The characteristic masses were 1.19, 0.45 and 0.48 pg, when integrated absorbance was measured for beryllium without the addition of any modifier and in the presence of Lu and Mg(NO₃)₂, respectively. The limits of detection (3σ) were 85, 19 and 58 fg, respectively. The accuracy and precision with the use of Lu and Mg(NO₃)₂ was tested for the direct determination of beryllium in urine samples. Quantification was performed with aqueous standards. The results obtained for the determination of beryllium in reference materials (Trace Elements in Urine), together with good recovery of spiked analyte, using either Lu or Mg(NO₃)₂ modification demonstrate the applicability of the procedure to the analysis of real samples. However, Lu provided the most accurate results. Also, the addition of Lu enhanced the precision of the measurements to levels of 1.8% relative standard deviation instead of 5.6 and 3.3% for the case of beryllium alone and with the addition of Mg(NO₃)₂.     

Graphite-tube effects on perchloric acid interferences on aluminum and thallium in the stabilized-temperature platform furnace

The determination of aluminum in the presence of perchloric acid is shown to depend upon the quality of the pyrolytic coating of furnace tubes. With new pyrolytically coated tubes, no interference was found from 0.5 M HClO₄ on 0.5 ng Al and no decrease in signal or deterioration of the pyrolytic coating was found after more than 150 firings. Very little interference was found in the determination of thallium in perchloric acid. In both cases the literature reported severe interferences. The determination of thallium and aluminum in perchloric acid appears to be more sensitive to the quality of the pyrolytic graphite coating than any of the materials studied previously here.     

Use of hydrogen for the elimination of matrix interferences in the determination of lead by graphite furnace atomic absorption spectrometry

Summary Comparatively high sulphur contents in brown algae (Fucus vesiculosus) cause interferences in the determination of lead by Graphite Furnace Atomic Absorption Spectrometry (GFAAS). These cannot always be eliminated by the application of the L'vov platform, matrix modifiers recommended for lead as (NH₄)₂HPO₄ and Mg(NO₃)₂, Zeeman-effect background correction and peak area evaluation.The behaviour of the lead absorbance signal obtained from the L'vov platform inserted into an uncoated as well as a pyrolytically coated graphite tube was examined in the presence of sodium and magnesium sulphate and (NH₄)₂HPO₄ and Mg(NO₃)₂ matrix modifiers.Accurate lead determinations could only be performed if hydrogen was used as alternate gas during drying and charring steps since this eliminated the interferences caused by sulphates.

---

Verwendung von Wasserstoff zur Eliminierung von Matrixstörungen bei der Bleibestimmung durch Graphitofen-AAS

Zusammenfassung Vergleichsweise hohe Schwefelgehalte in Braunalgen (Fucus vesiculosus) verursachen Störungen bei der Bestimmung von Blei mit Grahitrohrofen-AAS. Diese können nicht immer durch Anwendung der L'vov-Plattform und den für Blei empfohlenen Matrix-Modifizierer (NH₄)₂HPO₄ und Mg(NO₃)₂, Zeeman-Effekt-Untergrundkorrektur und Peakflächenauswertung behoben werden.Das Verhalten des Blei-Absorbance-Signals, das von einer L'vov-Plattform, die sowohl in ein unbeschichtetes wie in ein mit Pyrokohlenstoff beschichtetes Graphitrohr eingebracht wurde, erzeugt wird, wurde in Gegenwart von Natrium- und Magnesiumsulfat sowie (NH₄)₂HPO₄ und Mg(NO₃)₂-Matrix-Modifizierern untersucht.Richtige Bleibestimmungen konnten nur durchgeführt werden, wenn Wasserstoff als Alternativgas während des Trocknens und der thermischen Zersetzung verwendet wurde, was die durch Sulfat hervorgerufenen Störungen eliminierte.

     

Factors influencing the atomization of vanadium in graphite furnace AAS

We have made the determination of V conform to the requirements of the modern (stabilized temperature) furnace technology where the integrated absorbance (A·s) signals are used to quantitate analyte volatilized into a chamber whose temperature is relatively constant during the period when the analyte peak is measured. Graphite tubes with good pyrolytic coating and fast (maximum power) heating are required. We explored the advantages of specially designed tubes, of a cool-down procedure between the char and atomization steps and of very thin platforms. We found that Mg(NO₃)₂ was advantageous as a matrix modifier. With these conditions we found no problems with several matrices reported by earlier workers to be troublesome, for example HNO₃, phosphate, Fe, Mg and Ca. However metals that form very refractory carbides, such as La, Mo, W and Zr may remain troublesome for V, probably because mixed carbides result which include VC. A group of geological samples was analysed for V. Our recommendation is the use of wall atomization from tubes with good pyrolytic coatings, Mg(NO₃)₂ as a matrix modifier and the cool-down procedure to establish a nearly constant temperature along the tube.     

Determination of Beryllium in Natural Waters Using Atomic Absorption Spectrometry With Tantalum-Coated Graphite Tube

Abstract

In the present paper a method for direct determination of beryllium in natural waters, especially in surface waters, using atomic absorption spectrometry with graphite furnace is described. Two procedures are compared, using an ordinary graphite tube and matrix modifier Mg(NO₃)₂, and using a tantalum coated tube without any modifier added. The detection limit (3[sgrave]) of the proposed method using the tantalum-coated tube is proved to be 0.02 μgBe/1. With the developed method the Be content in natural water samples collected from highly polluted and reference regions of Bohemia were determined. A certified reference material (IAEA/W-4) was also analysed to prove the accuracy of proposed method.     

Study of chemical modifiers for the determination of chromium in biological materials by tungsten coil electrothermal atomic absorption spectrometry

The determination of Cr in digest solutions of mussels and non-fat milk powder by tungsten coil electrothermal atomic absorption spectrophotometry (TC-ETAAS) is affected by interferences. This study reports a critical evaluation of chemical modifiers that could be employed to correct these interferences. The chemical modifiers tested were: Mg [as Mg(NO₃)₂], Pd [as Pd(NO₃)₂], NH₄NO₃, ascorbic acid, and mixtures of these compounds. The less effective modifier was NH₄NO₃. The best effects, considering thermal stabilization and sensitivity, were obtained in mixtures of ascorbic acid plus Mg. Chromium was determined by TC-ETAAS in certified reference materials of mussels and non-fat milk powder, and results were comparable with those obtained by graphite furnace atomic absorption spectrophotometry (GFAAS).     

Study of chemical modifiers for the determination of chromium in biological materials by tungsten coil electrothermal atomic absorption spectrometry

The determination of Cr in digest solutions of mussels and non-fat milk powder by tungsten coil electrothermal atomic absorption spectrophotometry (TC-ETAAS) is affected by interferences. This study reports a critical evaluation of chemical modifiers that could be employed to correct these interferences. The chemical modifiers tested were: Mg [as Mg(NO₃)₂], Pd [as Pd(NO₃)₂], NH₄NO₃, ascorbic acid, and mixtures of these compounds. The less effective modifier was NH₄NO₃. The best effects, considering thermal stabilization and sensitivity, were obtained in mixtures of ascorbic acid plus Mg. Chromium was determined by TC-ETAAS in certified reference materials of mussels and non-fat milk powder, and results were comparable with those obtained by graphite furnace atomic absorption spectrophotometry (GFAAS). Received: 19 June 1998 / Revised: 11 January 1999 / Accepted: 16 January 1999     

On the direct analysis of solid samples by graphite furnace atomic absorption spectrometry

Summary We have studied some limitations of the solid sampling, cup-in-tube technique by comparison with a constant temperature two-step atomiser and found consistently lower vapour-phase temperatures and greater interferences in the former. With the former, higher vapour-phase temperatures and improved analytical results for lead and cadmium were found using Pd(NO₃)₂+Mg(NO₃)₂ instead of NH₄H₂PO₄+Mg(NO₃)₂ as modifier. Investigations of methods to extend the useful calibration range revealed reduced vapour-phase temperatures in the presence of a convective gas flow during atomisation, and a greater potential for errors using non-resonance lines. With respect to the latter, the absorbance signal is much more sensitive to matrix induced changes in the temperature interval in which atoms are formed compared to resonance lines. Furthermore, at the lead 261.4 nm non-resonance line we observed overcompensation errors caused by cobalt when using a Zeeman-effect system, and undercorrection due to the AlCl(g) molecule with a continuum source background corrector.     

The determination of low lead levels in the bone of lead-depleted mice by graphite furnace atomic absorption spectrometry

Low lead levels in the femurs of mice fed with a lead-depleted diet have been determined by use of electrothermal atomic absorption spectrometry with Zeeman-effect background correction. The method is based on the use of Mg(NO₃)₂/Pd as matrix modifier which enables significant reduction of the spectral interferences prevalent if chemical modifiers based on NH₄H₂PO₄ with either Ca or Mg are used for samples rich in Ca₃(PO₄)₂ matrix. The method was developed and validated by use of the NIST standard reference material 1486 bone. Bones were decomposed in a pressurized microwave-heated system using 70% nitric acid. Forty-three mice femurs, with a mass of 74.62 ± 12.54 mg, were dissolved in concentrated nitric acid. The lead results found in SRM 1486 (1.25 ± 0.15 μg g^–1, n = 9) were in good agreement with the certificate (1.335 ± 0.014 μg g^–1). Recoveries of 200 ng lead added to the SRM before or after digestion were 99.0 ± 1.4% and 98.5 ± 1.6%, respectively. The lead detection limit in bone samples is 0.06 μg g^–1 dry mass. This method is, therefore, suitable for the determination of very low lead levels (0.06–0.20 μg Pb kg^–1 bone) in the femurs of mice fed a diet with lead level of < 20μg kg^–1.     

Comparative study on the use of Ir, W and Zr-coated graphite tubes for the determination of chromium in slurries of human scalp hair by electrothermal atomic absorption spectrometry

The use of Ir, W and Zr-coated graphite tubes, as permanent chemical modifiers, was studied for the determination of chromium in human scalp hair by ETAAS using the slurry sampling technique. The use of Mg(NO₃)₂ and Pd, as aqueous chemical modifiers, was also investigated and compared to the use of the permanent chemical modifiers. Scalp hair samples were pulverized using a Zr vibrational ball mill, (mean particle diameter of 0.8 μm) and suspended in ultrapure water. The lowest limit of detection, 44.5 μg kg^–1,was achieved for the use of W-coated graphite tubes. The repeatability of the overall procedures (slurry preparation and ETAAS determination) were 15.7, 14.5 and 16.7% for W- and Zr-coated graphite tubes and Mg(NO₃)₂, respectively. The methods were applied to several reference materials, CRM 397 (human hair), DOLT-1 (dogfish liver) and DORM-1 (dogfish muscle), and the results obtained were in agreement to the certified values. Finally, the methods were applied to several human scalp hair samples from healthy adults.     

Molybdenum, Mo-Ir and Mo-Ru coatings as permanent chemical modifiers for the determination of cadmium and lead in sediments and soil samples by electrothermal atomic absorption spectrometry

Molybdenum, Ir, Ru, Mo-Ir, Mo-Ru thermally coated on to platforms inserted in pyrolytic graphite tubes as permanent modifiers and Pd + Mg(NO₃)₂ conventional modifier mixture have been employed for the determination of cadmium and lead in dissolved sediments and soil samples by electrothermal atomic absorption spectrometry (ETAAS). Optimum masses and mass ratios of permanent modifiers for the analysis of Cd and Pb in sample solutions have been investigated. The 280 μg of Mo, 200 μg of Ir, 200 μg of Ru, 280 μg of Mo + 200 μg of Ir or 280 μg of Mo + 200 μg of Ru has been found as efficient as 5 μg of Pd + 3 μg of Mg(NO₃)₂ for increasing thermal stabilization of analytes and for decreasing the most serious interferences. Pyrolysis and atomization temperatures, atomization and background signal shapes, characteristic masses and detection limits of analytes in dissolved samples with or without permanent and conventional modifiers have been compared. The detection limits and characteristic masses obtained with Mo-Ir coated platform are 0.01 μg g⁻¹ and 1.1 pg for Cd and 0.09 μg g⁻¹ and 19 pg for Pb, respectively. Long-term stabilities for analytes in samples with Mo, Mo-Ir, Mo-Ru and Pd + Mg(NO₃)₂ have been studied. Cadmium and lead contents have been determined in certified and standard reference materials by using optimum conditions investigated and the results obtained with Mo-Ir or Mo-Ru were in agreement with the values of certified reference materials.     

Suppression of interferences in the determination of lead in natural and drinking waters by graphite-furnace atomic absorption spectrometry

The problem of matrix interference encountered in the determination of lead in natural and drinking waters by graphite furnace atomic absorption spectrometry is examined by looking at the individual effects of various constituent salts (NaCl, KCl, MgCl₂ and CaCl₂, Na₂SO₄, KH₂PO₄ and Mg(NO₃)₂), of which MgCl₂ and Na₂SO₄ interfered most severely. The use of the L'vov platform decreased the sulphate interference, but was not successful in removing the other interferences. The mixture of 0.05% (w/v) lanthanum (as LaCl₃) and 1% (v/v) nitric acid previously proposed for wall atomisation was found to be effective in controlling the interferences. Nitric acid alone removed almost completely the effects of MgCl₂ and CaCl₂, but had little effect on the interference of sulphate, which required the addition of lanthanum for suppression. The removal of interferences in real water samples by the lanthanum/nitric acid mixture is demonstrated by comparison of results obtained by this approach with those obtained by atomic fluorescence spectrometry and by flame atomic absorption spectrometry after preconcentration by evaporation.     

The selection of a chemical modifier for vanadium determination in various types of natural waters by electrothermal atomic absorption spectrometry

Various modifiers (ascorbic acid, NH₄NO₃, EDTA, NH₄SCN and a mixture of Pd/Mg(NO₃)₂) are compared for the accurate determination of vanadium in natural waters by electrothermal atomic absorption spectrometry. The interferences of compounds commonly present in natural waters, such as NaCl, CaCl₂, MgCl₂ and FeCl₃ are studied. Matrix interferences were effectively eliminated by ascorbic acid or ammonium nitrate. For comparison, the standard addition method was applied without a modifier which provided satisfactory results. The accuracy of the method was confirmed by analysis of certified reference materials of waters (‘Trace Metals in Drinking Water’ and SRM 1643e ‘Trace Elements in Water’) as well as by recoveries of vanadium spiked to tap water, mineral water, synthetic riverine and synthetic sea waters. The limits of detection and characteristic masses for ascorbic acid and ammonium nitrate as the modifiers were 1.71 and 1.56?µg?L^?1 and 70 and 67?pg, respectively. Recovery was in the range of 98–105% and RSD was less than 5%.     

Evaluation of tungsten–rhodium coating on an integrated platform as a permanent chemical modifier for cadmium,lead, and selenium determination by electrothermal atomic absorption spectrometry

A tungsten–rhodium coating on the integrated platform of a transversely heated graphite atomizer is proposed as a permanent chemical modifier for the determination of Cd, Pb, and Se by electrothermal atomic absorption spectrometry. It was demonstrated that coating with 250 μg W+200 μg Rh is as efficient as the conventional Mg(NO₃)₂+NH₄H₂PO₄ or Pd+Mg(NO₃)₂ modifiers for avoiding most serious interferences. The permanent W–Rh modifier remains stable for 300–350 firings of the furnace, and increases tube lifetime by 50%–100% when compared to pyrolytic carbon integrated platforms. Also, there is less degradation of sensitivity during the atomizer lifetime when compared with the conventional modifiers, resulting in a decreased need of re-calibration during routine analysis. The characteristic masses and detection limits achieved using the permanent modifier were respectively: Cd 1.1±0.4 pg and 0.020 μgL⁻¹; Pb 30±3 pg and 0.58 μgL⁻¹ and Se 42±5 pg and 0.64μgL⁻¹. Results from the determination of these elements in water reference materials were in agreement with the certified values, since no statistical differences were found by the paired t-test at the 95% level.     

Determination of selenium in seawater by Zeeman GFAAS using nickel plus NH4NO3 modifier

The effectiveness of nickel plus NH₄NO₃ as a chemical modifier for the determination of selenium in seawater by Zeeman electrothermal atomic absorption spectrometry has been evaluated. The effect of changing the modifier mass and pyrolysis hold time on the integrated absorbance of selenium and the background absorbance has been investigated. Nickel and NH₄NO₃ allow the quantitative stabilization of selenium in the seawater matrix up to 1300° C as compared with 600° C without modifier. The modifier further reduces the background absorbance caused by seawater. The tolerable amounts of various inteferences such as chloride, sulphate and phosphorus in the presence of nickel plus NH₄NO₃ are evaluated for the determination of selenium in seawater. Received: 31 August 1995 / Revised: 21 December 1995 / Accepted: 6 January 1996     

Lead atomization in the presence of aluminum matrices by electrothermal atomic absorption spectrometry. A comparative study of slurry vs solution sample introduction

The atomization behaviour of Pb introduced to the electrothermal atomizer in a slurry of Al₂O₃ and in a solution of Al(NO₃)₃ has been studied. The characteristics of the absorbance vs time profiles are highly dependent on the way in which Pb is incorporated in the matrix. In particular, Pb adsorbed on the surface of Al₂O₃ particles behaves differently from Pb entrapped within the particles. Atomization using platform and wall atomization from both pyrolytic and non-pyrolytic graphite surfaces is described. Pyrolytic platforms do not always provide complete recovery and better results are obtained with atomization from a non-pyrolytic platform surface within a pyrolytically coated tube. With wall atomization, large differences in the absorbance vs time profiles precludes its use for quantitative determinations. However, wall atomization should be useful for future studies of the kinetic and thermodynamic processes of Pb release. Finally, the feasibility of using the non-resonance Pb line at 261.4 nm to reduce the analytical sensitivity is examined. The strong dependence of the lower energy level population on temperature makes this difficult, but the absorbance profiles with non-pyrolytic platform atomization show that all forms of Pb can be made to atomize at similar temperatures.     

Determination of nitrite, nitrate, bromide, and iodide in seawater by ion chromatography with UV detection using dilauryldimethylammonium-coated monolithic ODS columns and sodium chloride as an eluent

A method was developed for determination of inorganic anions, including nitrite (NO ₂ ^? ), nitrate (NO ₃ ^? ), bromide (Br^?), and iodide (I^?), in seawater by ion chromatography (IC). The IC system used two dilauryldimethylammonium bromide (DDAB)-coated monolithic ODS columns (50?×?4.6?mm i.d. and 100?×?4.6?mm i.d.) connected in series for separation of the ions. Aqueous NaCl (0.5?mol/L; flow rate, 3?mL/min) containing 5?mmol/L phosphate buffer (pH 5) was used as the eluent, and detection was with a UV detector at 225?nm. The monolithic ODS columns were coated and equilibrated with a 1-mmol/L DDAB solution (in H₂O/methanol, 90:10 v/v). The hydrophilic ions (NO ₂ ^? , NO ₃ ^? , and Br^?) were separated within 3?min and the retention time of I^? was 16?min. No interferences from matrix ions, such as chloride and sulfate ions, were observed in 35?‰ artificial seawater. The detection limits were 0.6?μg/L for NO ₂ ^? , 1.1?μg/L for NO ₃ ^? , 70?μg/L for Br^?, and 1.6?μg/L for I^? with a 200-μL sample injection. The performance of the coated columns was maintained without addition of DDAB in the eluent. The IC system was successfully applied to real seawater samples with recovery rates of 94–108?% for all ions.

Application of Tungsten-Rhodium Permanent Chemical Modifier in Slurry Analysis: Determination of Cadmium

 A tungsten-rhodium coating on the integrated platform of a transversely heated graphite atomiser (THGA) was used as a permanent chemical modifier for the determination of Cd in sediment slurries by electrothermal atomic absorption spectrometry. Slurries were ultrasonicated during 20 s before being delivered to the previously W-Rh treated platform. The permanent W-Rh modifier remains stable by approximately 250 measurements when 20 μl of slurries containing up to 1.0% m/v are delivered into the atomiser. In addition, the permanent modifier increases the tube lifetime up to 720 analytical firings. Also, when the W-Rh permanent modifier was employed, there was less variation of the slope of the analytical curves during the total atomiser lifetime, resulting in a decreased need of re-calibration during routine analysis, increasing the sample throughput. The atomiser lifetime was limited to the THGA wall durability, because the W-Rh treated platform was intact after more than 720 analytical firings. Detection limits based on integrated absorbance for 1.0% m/v slurries were 1.5 ng g⁻¹ Cd for 250 μg W +200 μg Rh permanent modifier and 11.5 ng⁻¹ Cd for 5 μg Pd +3 μg Mg(NO₃)₂. Results for the determination of cadmium in sediment slurries using the W-Rh permanent modifier were in agreement with those obtained with dissolved sample solutions by using Pd + Mg(NO₃)₂, since no statistical differences were found by the paired t-test at the 99% level. Received September 6, 1999. Revision December 1, 1999.     

Diagramme polythermique du systeme ternaire H2O—Al(NO3)3—Mg(NO3)2

The solid—liquid equilibria of the ternary system H₂O—Al(NO₃)₃—Mg(NO₃)₂ were studied at –30, –20, –10 and 0°C by using a synthetic method which allows to detemine all the characteristic points of isothermal sections. The stable solid phases which appear are respectively: ice, Al(NO₃)₃·9H₂O, Mg(NO₃)₂·9H₂O and Mg(NO₃)₂·6H₂O. Neither double salts nor mixed crystals are observed in the temperature and composition field studied. Polytherm diagram layout show two invariant transformations correspond with an eutectic point and a peritectic point.This revised version was published online in November 2005 with corrections to the Cover Date.