Application of a xenon arc lamp as a light source for evaporative light scattering detection

The standard tungsten-halogen light source used in a commercial evaporative light scattering detector (ELSD) was replaced with a 180 W xenon arc lamp. The xenon arc lamp possesses a broader spectrum in the UV region than the halogen source. The influence of the UV transmittance of five selected solvents was studied with a size-exclusion chromatography column. This solvent parameter was not observed to influence the ELSD response between the two light source settings. With the solvents studied, better sensitivity was obtained with the xenon arc lamp than the halogen lamp. This high-energy source was applied to ceramide III analysis with an octadecyl-grafted silica column and methanol:tetrahydrofuran 97:3 as the mobile phase, and the sensitivity of the quantification of ceramide III increased 16-fold for injected amounts of 14∼140 ng. The molecular species in a sample of naturally occurring ceramides was analyzed using two C18 columns at 40 °C and gradient elution from 100% acetonitrile to 100% isopropanol in 30 min. The increased ELSD sensitivity achieved when using the xenon arc lamp allowed both the minor and major ceramide species to be observed, in contrast to the results achieved when the halogen lamp was used, where the increased photomultiplier voltage needed to observed the signals from the minor species caused the signals from the major ceramide species to occur above the detector response window.     

Optimization of a simultaneous multi-element atomic absorption spectrometer

A variable-size simplex procedure was used to optimize the overall response of a simultaneous multi-element flame atomic absorption spectrometer. Seven factors (air to fuel ratio, slit width, height above the burner head, and four hollow cathode lamp currents) were optimized for copper, iron, manganese, and zinc atomic absorption. A univariate search procedure was used to determine the effect of individual factors on response. The results of the optimization showed that a comprise set of operating conditions must be used when performing multi-element determinations. The atomic absorption sensitivity of the multi-element determination as compared to single-element determination was reduced by a factor of no more than two.     

Catalytic kinetic simultaneous determination of iron, silver and manganese with the Kalman filter by using flow injection analysis stopped-flow spectrophotometry

A catalytic differential kinetic method with Kalman filter for the simultaneous determination of multi-component is described. The oxidization of Rhodamine B (RB) by potassium periodate in a slightly acid solution is a slow reaction. But iron(III), silver(I) or manganese(II) has a differential catalytic effect on the oxidation reaction of RB in the presence of 1,10-phenanthroline as the activator. So iron, silver and manganese can be simultaneously determined by measuring the decreasing absorbance of the dye (RB) at 555 nm. A flow injection analysis stopped-flow spectrophotometric system with a microcomputer performs the determinations. This method has been applied to determining iron, silver and manganese of alloy samples with satisfactory results.     

Simultaneous determination of manganese and zinc in mixtures using first- and second-derivative spectrophotometry

A new direct spectrophotometric determination of manganese with 5,8-dihydroxy-1,4-naphthoquinone (naphthazarin,NAZA) is reported. Absorption maximum, molar absorptivity and Sandell's sensitivity of 1:2 (M:L) complex are 695 nm, 1.88x10(4) l mol(-1) cm(-1) and 2.92 ng cm(-2), respectively. A linear calibration graph is obtained up to a concentration of 7.2 mug ml(-1) of manganese. The optimum range for determination (Ringbom) is between 0.20 and 6.8 mug ml(-1). A rapid method for simultaneous determination of manganese and zinc in their mixture using derivative spectra is described. The range 0.28-5.6 mug ml(-1) manganese could be determined in the presence of 0.33-6.8 mug ml(-1) zinc and vice versa. The developed method was applied to the simultaneous spectrophotometric determination of manganese and zinc in some synthetic mixtures and was found to give satisfactory results.     

Simultaneous determination of methylxanthines in different types of tea by a newly developed and validated TLC method

The aim of this paper is to develop a new simple, fast and economical method for simultaneous quantitative determination of methylxanthine compounds based on TLC combined with image analysis. To obtain certain results, both extraction and chromatographic separation were optimized. The optimum extraction conditions were maceration in ethanol-water 8:2, v/v. The chromatographic separations were done on the silica gel F(254) TLC plates developed with chloroform-dichloromethane-isopropanol, 4:2:1 v/v/v. Detection was performed under UV lamp at 254?nm and the evaluation of the chromatographic plate was based on digital processing of chromatographic images. The developed TLC method was validated for parameters such as specificity, linearity and range, LOD and LOQ, precision, robustness and accuracy. This method was then applied for determination of caffeine, theobromine and theophylline in different types of tea, commercially available. Moreover, the content of methylxanthines detected and determined in commercial tea samples can be used as chemical marker in quality control.     

Simultaneous spectrofluorimetric determination of iron and manganese by a differential kinetic catalytic method

A kinetic method is presented for the simultaneous determination of iron(III) and manganese(II) based on the different reaction rates resulting from the catalytic effect of both metal ions on the oxidation of 2-hydroxybenzaldehyde thiosemicarbazone by hydrogen peroxide in an ammoniacal medium. The reaction is monitored spectrofluorimetrically at 440 nm and with excitation at 365 nm. Two sets of reaction conditions are established to maximize the effect of manganese compared to iron, and vice versa, and the data are evaluated from simultaneous equations. Mixtures of these metal ions at ng ml^?1 levels for iron/manganese ratios from 8:1 to 1:2 can be determined with an accuracy and precition of about 3% and 1%, respectively. The methods has been applied successfully to the determination of both metals in aluminium and copper alloys, beer, cheeses and soils.     

Screening of dissolved heavy metals (Cu,Zn, Mn,Al, Cd,Ni, Pb) in seawater by a liquid-membrane–ICP–MS approach

A bulk liquid membrane system has been developed and applied to the simultaneous separation and preconcentration of up to seven heavy metals (copper, zinc, lead, cadmium, aluminium, manganese, and nickel) in seawater. Copper was selected to optimize transport conditions and then, under these conditions, the simultaneous extraction of other heavy metals was studied. The system achieved preconcentration yields ranging between 44.11% (Cd) and 77.77% (Cu) after nine hours of operation, the effectiveness of metal transport being Cu > Zn > Pb > Mn > Ni > Al > Cd. The system was applied to the preconcentration of four real seawater samples before their quantification by inductively coupled plasma–mass spectrometry (ICP–MS). Compared with the analytical procedures commonly used for trace metal determination in oceanography, the results obtained demonstrated that the new system may be used as a very clean (sample contamination-free), simple, and one-step alternative for semiquantitative, and even quantitative, simultaneous determination of heavy metals in seawater.     

Analytical characteristics of a continuum-source tungsten coil atomic absorption spectrometer.

A continuum-source tungsten coil electrothermal atomic absorption spectrometer has been assembled, evaluated, and employed in four different applications. The instrument consists of a xenon arc lamp light source, a tungsten coil atomizer, a Czerny-Turner high resolution monochromator, and a linear photodiode array detector. This instrument provides simultaneous multi-element analyses across a 4 nm spectral window with a resolution of 0.024 nm. Such a device might be useful in many different types of analyses. To demonstrate this broad appeal, four very different applications have been evaluated. First of all, the temperature of the gas phase was measured during the atomization cycle of the tungsten coil, using tin as a thermometric element. Secondly, a summation approach for two absorption lines for aluminum falling within the same spectral window (305.5-309.5 nm) was evaluated. This approach improves the sensitivity without requiring any additional preconcentration steps. The third application describes a background subtraction technique, as it is applied to the analysis of an oil emulsion sample. Finally, interference effects caused by Na on the atomization of Pb were studied. The simultaneous measurements of Pb and Na suggests that negative interference arises at least partially from competition between Pb and Na atoms for H2 in the gas phase.     

Determination of traces of calcium, magnesium, iron and nickel in aluminium salts by atomic-absorption spectrophotometry with a microwave-excited source and hollow-cathode lamps

The determination of trace amounts of calcium and magnesium in solutions containing large concentrations of aluminium salts may be accomplished by co-precipitating their hydroxides on iron(III) hydroxide, dissolving the precipitate, and extracting the 8-hydroxyquinolates of calcium and magnesium into methyl isobutyl ketone at about pH 11. The extract may be sprayed into the airpropane flame of a simple unmodulated spectrophotometer and atomic-absorption measurements for calcium and magnesium made at 4227 and 2852 A respectively. The limits of determination correspond to 10 and 1 ppm of calcium and magnesium in solid alumina. Iron and nickel may be co-precipitated on hydrated manganese(IV) oxide and their 8-hydroxyquinolates extracted at pH 4.5. Measurements of atomic absorption for these elements at 2483 and 2320 A respectively yield limits of determination corresponding to 10 ppm in alumina. Hollow-cathode lamps may be used for calcium, magnesium and nickel, but a simple microwave-excited discharge tube gives much better sensitivity than a hollow-cathode lamp for iron.     

Recent developments with light-exposure apparatus and measurement of radiation of their light sources

New techniques and devices which were recently developed in order to avoid various drawbacks of current light-exposure apparatus are introduced. The spectral distribution of the open flame carbon arc approximates more closely to that of sunlight by modifications of the filter system.The life of carbon arcs was lengthened more than two fold. The long-life xenon arc lamp minimized the reduction in output of radiation.The slanted holder improved the locational variance of radiation falling on a specimen.The instrumental methods for measuring light dosage are explained.     

Comparison and application of two microextractions based on syringe membrane filter

Two proposed syringe membrane filter solid phase microextraction and syringe membrane filter liquid/solid phase microextraction, coupled separately with high performance liquid chromatography, were developed for simultaneous enrichment and determination of the trace level of flavonoids in traditional Chinese medicine. In syringe membrane filter solid phase microextraction, the membrane of syringe membrane filter was served as a solid adsorption film to adsorb target analytes. And in syringe membrane filter liquid/solid phase microextraction, the membrane of syringe membrane filter was used as not only an adsorption phase, but also as a holder of extraction solvent to realize liquid‐solid synergistic extraction. The simple operation, rapid extraction, and little or no organic solvent consumption make the two approaches very interesting. To evaluate the two proposed approaches, the crucial parameters affecting the enrichment factors of target analytes were investigated and optimized, and the two microextractions were intercompared. Moreover, their microextraction mechanisms were analyzed and described. Under the optimized conditions, both the new approaches achieved good linearities, accuracies, precisions, and low limits of detection, and the two methods were successfully applied for concentration of the flavonoids in traditional Chinese medicines.     

Highly Sensitive and Selective Determination of Manganese in Tea Leaves by a Catalytic Kinetic Spectrophotometric Method

The catalytic effect of manganese(II) on the oxidation of barium diphenylamine sulfonate (BDAS) with potassium bromate in sulfuric acid was studied. Progress of the reaction was monitored, spectrophotometrically, by measuring absorbance changes at 547.5 nm. A highly sensitive, selective and simple method was accordingly developed for the determination of trace amounts of Mn(II), with no need for a separation or pre‐concentration step. Effects of reaction time, concentration of reagents, temperature and ionic strength on the reaction rate were studied. In the optimized conditions, manganese could be determined in a range of 1 to 60 ng mL^?1 with a detection limit of 0.2 ng mL^?1. The proposed method was successfully applied to the determination of manganese in tea leaves.     

Purity control of uranium by neutron activation assay--II. Determination of manganese, nickel and copper

Activation analysis is applied for the simultaneous determination of manganese, nickel and copper in different uranium samples, including metallic uranium, uranium concentrates, oxide, acetate, nitrate and sodium uranate. The analytical scheme developed is based on separation of the uranium by paper chromatography and subsequent determination of these elements in the pile-irradiated residues by simple radiochemical operations. The reliability of the scheme proposed is tested, and the limits of sensitivity of the methods worked out are ascertained. Accordingly, microgram concentrations of the elements studied could be assayed in limited quantities of the samples analysed with a precision of +/- 15%. Reagent-blank determinations are also considered.     

Spectrophotometric determination of manganese(VII) using benzyltriphenylphosphoniumchloride as a new reagent and application of artificial neural network to extending the dynamic range of determination

A simple and selective spectrophotometric method is proposed for the determination of trace amounts of manganese. The method is based on the extraction of manganese as a MnO₂-benzyltriphenylphosphoniumchloride ion pair with chloroform. An artificial neural network (ANN) has been applied to the handling of the spectrophotometric data of this complex in the organic phase to extend the dynamic range of manganese determination (0.020–6.0 μg/mL). A three-layer back-propagation network (50:75:1) was used with root-mean-square error (rmse) 0.001 and momentum (m) 0.8 overall. The application of BP-ANN makes it possible to extend the dynamic range of the determination of manganese from its narrow linear range of 0.020–2.5 μg/mL to the dynamic range 0.020–6.0 μg/mL. The text was submitted by the author in English.     

Rapid and simple method for the determination of copper, manganese and zinc in rat liver by direct flame atomic absorption spectrometry.

An acidic homogenate method, which includes simple homogenization pre-treatment of tissue material and direct nebulization flame atomic absorption spectrometry (FAAS), is successfully applied to the simultaneous determination of copper, manganese and zinc in rat liver. The proposed method involves only a few steps for sample pre-treatment at room temperature, making the risk of systematic errors very small. Because recoveries of 101% for copper, 98% for manganese and 100% for zinc could be achieved using aqueous standards, matrix-matched standards were redundant. Favourable results obtained in biological media, including limits of detection of 0.04, 0.03 and 0.04 mg l-1 for Cu, Mn and Zn, respectively, together with accuracies of 0-3%, and relative standard deviations ranging from 2 to 10% are further evidence of the suitability of the method.     

Capillary electrophoretic-ultraviolet method for the separation and estimation of zineb, maneb, and ferbam in food samples

A simple and sensitive capillary electrophoretic method with ultraviolet detection has been developed for the separation and determination of ferbam [iron(III)-dimethyldithiocarbamate], maneb [manganese(II)-ethylenebisdithiocarbamate] and zineb [zinc(II)-ethylenebisdithiocarbamate], in borate buffer, after their acidic decomposition and complexation with CDTA (trans-1,2-diaminocyclohexane-N,N,N',N'-tetraacetic acid monohydrate), as CDTA-metal complexes of Fe+3, Mn +2, and Zn+2. The determination is dependent on the pH and the nature of the buffer solutions. In this method, the detection limit (signal-to-noise ratio = 3) is 0.0013, 0.0022, and 0.0023 mM for ferbam, maneb, and zineb, respectively. The relative standard deviation for the analysis of 1 mM of each was found to be 1.5 +/- 0.2%. The method was successfully applied for the analysis of red beans and grain samples spiked with ferbam, maneb, and zineb. The applicability of capillary electrophoresis as a useful tool for the simultaneous determination and analysis of ferbam, maneb, and zineb is demonstrated.     

Simultaneous multielemental determination using a low-resolution inductively coupled plasma spectrometer/diode array detection system

This work presents a versatile method for simultaneous multielemental analysis using detection with photodiode arrays and multivariate calibration techniques. A multidetection system based on an array of 1024 photodiodes was built and adapted to a commercial plasma emission scanning spectrometer. Spectral data were acquired at low resolution, allowing simultaneous monitoring of a broad spectral range and resulting in very informative but considerably overlapped spectra. Partial least squares and principal component regressions were employed to minimize overlapping problems. A numerical procedure for window selection was also developed.

The new method was applied to the simultaneous determination of manganese, molybdenum, nickel, chromium and iron in steel samples, resulting in average relative prediction errors of 2.1% for Mn, 3.4% for Mo, 0.6% for Cr, 1.5% for Ni and 0.8% for Fe. These errors are comparable to those observed with conventional scanning detection systems and separate univariate calibrations, but the new method allows simultaneous determination of the five elements, with data acquisition significantly faster than in scanning instruments.     

Simple method for the simultaneous determination of noradrenaline, dopamine and serotonin by stepwise elution from a short column of weak cation-exchange resin

A simple method for the simultaneous determination of noradrenaline, dopamine and serotonin using a short column of Amberlite CG-50 is described. Noradrenaline and dopamine were eluted from the column with phosphate buffers containing 1.5 and 4.0% boric acid, respectively, and then serotonin was eluted with 1.0 N HCl. Catecholamines were determined by a modification of the ethylenediamine condensation method using potassium ferricyanide as oxidant and isobutanol for extraction of the fluorophores. Serotonin was measured by the acidic o-phthalaldehyde method. The method was applied to the simultaneous determination of noradrenaline, dopamine and serotonin in discrete regions of rat brain.     

卡尔曼滤波分光光度法同时测定钢中钛和钼

本文采用卡尔曼滤波(KF)递推法,以苯基荧光酮-溴化十六烷基吡啶与钛,钼的显色体系同时测定钛和钼,同时以柠檬酸和抗坏血酸掩蔽干扰,并引入误差校正因子来校正加掩蔽剂后在所测波段范围内所造成的残余背景吸收,用于实际钢样分析,获得较满意的结果。