A novel method to prepare monolithic molecular imprinted polymer fiber for solid‐phase microextraction by microwave irradiation†

In this paper, a new approach to prepare monolithic molecularly imprinted polymer (MIP) fibers for solid‐phase microextraction is proposed with the help of microwave irradiation. Imprinting polymerization was carried out within silica capillaries in 4.5 min, using dimethyl phthalate (DMP) as a template molecular, α‐methacrylic acid as a functional monomer and ethylene dimethacrylate as a crosslinker, acetonitrile as the porogenic solvent. The synthesis was optimized by varying the ratio of template/monomer and different volume of porogen. The resulted MIP fibers were obtained after silica being etched away with a controlled length of 1 cm, and subsequently characterized by SEM. In order to increase the selective extraction of DMP, factors affecting the extraction including extraction time, salt concentration, desorption time, and desorption solvents were investigated for solid‐phase microextraction procedures in detail. The selectivity coefficients, defined as the extraction amount ratio of MIP to its nonimprinting fiber, were 5.6, 2.6, and 1.4 for DMP and its counterpart including dibutyl phthalate and di‐n‐octylo‐phthalate, respectively. The resulted fibers were also applied to detect DMP, dibutyl phthalate, and di‐n‐octylo‐phthalate in bottled beverage samples coupled to HPLC and resulted in relative recoveries of up to 73.8–98.5%, respectively.     

An investigation into possible sources of phthalate contamination in the environmental analytical laboratory

A study of common laboratory equipment and components was performed in order to identify sources of contamination of phthalates prior to testing environmental samples for such compounds. A screening study revealed significant leaching from laboratory consumables, such as plastic syringes, pipette tips released maximum leachings of 0.36?µg?cm^?2 diethylhexyl phthalate (DEHP) and 0.86?µg?cm^?2 diisononyl phthalate (DINP), plastic filter holders produced maximum leachings of 2.49?µg?cm^?2 dibutyl phthalate (DBP) from polytetrafluoroethylene (PTFE); specifically 0.61?µg?cm^?2 DBP from regenerated cellulose and 5.85?µg?cm^?2 dimethyl phthalate (DMP) from cellulose acetate and Parafilm® leached levels up to 0.50?µg?cm^?2 DEHP. In addition, a high-temperature bake-out process was found necessary to eliminate quite high levels of two phthalates present in a commercial bulking agent for pressurized liquid extraction.     

Nanostructured copper‐coated solid‐phase microextraction fiber for gas chromatographic analysis of dibutyl phthalate and diethylhexyl phthalate environmental estrogens

A novel nanostructured copper‐based solid‐phase microextraction fiber was developed and applied for determining the two most common types of phthalate environmental estrogens (dibutyl phthalate and diethylhexyl phthalate) in aqueous samples, coupled to gas chromatography with flame ionization detection. The copper film was coated onto a stainless‐steel wire via an electroless plating process, which involved a surface activation process to improve the surface properties of the fiber. Several parameters affecting extraction efficiency such as extraction time, extraction temperature, ionic strength, desorption temperature, and desorption time were optimized by a factor‐by‐factor procedure to obtain the highest extraction efficiency. The as‐established method showed wide linear ranges (0.05–250 μg/L). Precision of single fiber repeatability was <7.0%, and fiber‐to‐fiber repeatability was <10%. Limits of detection were 0.01 μg/L. The proposed method exhibited better or comparable extraction performance compared with commercial and other lab‐made fibers, and excellent thermal stability and durability. The proposed method was applied successfully for the determination of model analytes in plastic soaking water.     

Determination of phthalate esters from environmental water samples by micro‐solid‐phase extraction using TiO2 nanotube arrays before high‐performance liquid chromatography

We describe a highly sensitive micro‐solid‐phase extraction method for the pre‐concentration of six phthalate esters utilizing a TiO₂ nanotube array coupled to high‐performance liquid chromatography with a variable‐wavelength ultraviolet visible detector. The selected phthalate esters included dimethyl phthalate, diethyl phthalate, dibutyl phthalate, butyl benzyl phthalate, bis(2‐ethylhexyl)phthalate and dioctyl phthalate. The factors that would affect the enrichment, such as desorption solvent, sample pH, salting‐out effect, extraction time and desorption time, were optimized. Under the optimum conditions, the linear range of the proposed method was 0.3–200 μg/L. The limits of detection were 0.04–0.2 μg/L (S/N = 3). The proposed method was successfully applied to the determination of six phthalate esters in water samples and satisfied spiked recoveries were achieved. These results indicated that the proposed method was appropriate for the determination of trace phthalate esters in environmental water samples.     

Utilization of homogeneous liquid–liquid extraction followed by HPLC-UV as a sensitive method for the extraction and determination of phthalate esters in environmental water samples

A simple and sensitive method for the extraction of four phthalate esters including dimethyl phthalate (DMP), diethyl phthalate (DEP), benzyl butyl phthalate (BBP) and di-n-butyl phthalate (DBP) as well as their determination in water samples was developed using homogeneous liquid–liquid extraction (HLLE) and HPLC-UV. The extraction method is based on the phase separation phenomenon by the salt addition to the ternary solvent system. The extraction parameters such as type and volume of extracting and consolute solvent, concentration of salt, pH of sample and extraction time were optimized. Under the optimal conditions (extraction solvent: 100?µL CHCl₃; consolute solvent: 2.0?mL methanol; NaCl 15% (w/v) and pH of sample: 6.5) extraction recovery was in the range of 92–102%. Linearity was observed in the range of 0.5–300?µg?L^?1 for DEP and 0.6–300?µg?L^?1 for DMP, BBP and DBP. Correlation coefficients (r ²), limits of detection (LODs) and relative standard deviations (RSDs) were in the ranges of 0.9976–0.9993, 0.18–0.25 and 1.5–4.8%, respectively. The method was successfully applied for the preconcentration and determination of these phthalate esters in the several environmental water samples.     

Thermodynamic properties of dimethyl phthalate + vinyl acetate, diethyl phthalate + vinyl acetate or bromocyclohexane, and dibutyl phthalate + vinyl acetate or 1,2-dichlorobenzene at T = 298.15–308.15 K

Thermodynamic properties (densities and viscosities) of binary mixtures of diethyl phthalate (DEP) + bromocyclohexane, dibutyl phthalate (DBP) + 1,2-dichlorobenzene, and vinyl acetate (1) + dimethyl phthalate (DMP) (2), + diethyl phthalate (2), or + dibutyl phthalate (2) were measured over the whole range of mole fractions at atmospheric pressure and different temperatures (T = 298.15 K to 308.15 K). For these mixtures, their excess molar volumes (V ^E) and viscosity deviations (Δη) were calculated from the experimental data. These results were correlated with the Redlich-Kister polynomial equation to derive the coefficients and standard errors.     

Preparation and Characterization of PVDF‐HFP Membrane

Poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP) microporous membrane was prepared by supercritical CO₂ extraction of dibutyl phthalate (DBP) template from PVDF‐HFP/DBP film. The effects of extraction conditions such as pressure, temperature, and extraction time on extraction efficiency and the porosity of membrane were studied. The extraction efficiency of DBP and size stability of polymer membrane during extraction was compared with those of solvent extraction process. The structure of the resulting membrane was characterized by scanning electron microphotograph (SEM), X‐ray diffraction (XRD) and differential scanning calorimeter (DSC). With increasing the extraction temperature, pressure and time, the extraction efficiency and the porosity increased. Maximum extraction efficiency is obtained at extraction pressure and temperature higher than 18 MPa and 75°C, respectively. The porosity of membranes depended on the extraction efficiency and shrinkage ratio of membranes. Compared with solvent extraction, supercritical CO₂ extraction of the film generated the membrane with more uniform structure and higher porosity.     

Simultaneous determination of phthalates and adipates in human serum using gas chromatography–mass spectrometry with solid‐phase extraction

A gas chromatography–mass spectrometry assay was developed and validated for the simultaneous determination of phthalates and adipates in human serum. The phthalates and adipates studied were dimethyl phthalate, diethyl phthalate, dibutyl phthalate, benzylbutyl phthalate, di‐2‐ethylhexyl phthalate, di‐n‐octyl phthalate, diethyl adipate, dibutyl adipate, diisobutyl adipate, bis(2‐butoxyethyl) adipate and di‐2‐ethylhexyl adipate, with diisooctyl phthalate as internal standard. The extraction and cleaning up procedure was carried out with solid‐phase extraction cartridges containing dimethyl butylamine groups, which showed extraction efficiencies over 88% for each analyte and the internal standard. The calibration curves obtained were linear with correlation coefficients greater than 0.98. For all analytes, the assay gave CV% values for intra‐day precision from 4.9 to 13.3% and mean accuracy values from 91.4 to 108.4%, while inter‐day precision was 5.2–13.4% and mean accuracy 91.0–110.2%. The limits of detection for the assay of phthalates and adipates were in the range 0.7–4.5 ng/mL. The method is simple, sensitive and accurate, and allows for simultaneous determination of nanogram levels of phthalates and adipates in human serum. It was successfully applied to an investigation on the level of phthalates and adipates in a non‐occupationally exposed population.     

Bioassay‐guided isolation of an active compound with protein tyrosine phosphatase 1B inhibitory activity from Sargassum fusiforme by high‐speed counter‐current chromatography

A rapid and efficient method using high‐speed counter‐current chromatography was established for the bioassay‐guided separation of an active compound with protein tyrosine phosphatase 1B inhibitory activity from Sargassum fusiforme. Under the bioassay guidance, the ethyl acetate extract with the best IC₅₀ value of 0.37 ± 0.07 μg/mL exhibited a potential protein tyrosine phosphatase 1B inhibitory activity, which was further separated by high‐speed counter‐current chromatography. The separation was performed with a two‐phase solvent system composed of n‐hexane/methanol/water (5:4:1, v/v). As a result, dibutyl phthalate (19.7 mg) with the purity of 95.3% was obtained from 200 mg of the ethyl acetate extract. Its IC₅₀ was 14.05 ± 0.06 μM, which was further explained by molecular docking. The result of molecular docking showed that dibutyl phthalate enfolded in the catalytic site of protein tyrosine phosphatase 1B. The main force between dibutyl phthalate and protein tyrosine phosphatase 1B was the hydrogen bond interaction with Gln266. In addition, hydrogen bond, van der Waals force and hydrophobic interaction with the amino acids (Ala217, Ile219, and Gly220) were also responsible for the stable protein‐ligand complex.     

Simultaneous determination of fifteen multiclass organic pollutants in human saliva and serum by liquid chromatography–tandem ultraviolet/fluorescence detection: A validated method

A quick and inexpensive validated method, based on sample treatment by liquid–liquid microextraction followed by liquid chromatography (LC) coupled with ultraviolet tandem fluorescence detection is proposed for the determination of 15 multiclass pollutants both in serum and in saliva, as a simple and easy to draw matrix. The method was set up and validated according to European guidelines. The compounds of interest include some endocrine‐disrupting chemicals (i.e. bisphenol A, bisphenol B, bisphenol E, bisphenol F, bisphenol AF, bisphenol A diglycidyl ether, bisphenol M, diethylhexyl phthalate, monoethylhexyl phthalate, triclosan and 4‐nonylphenol), as well as other pollutants belonging to the class of volatile organic compounds (2‐chlorophenol, 1,2 dichlorobenzene, 1,2,4,5‐tetrachlorobenzene). The limits of quantifications ranged from 2.28 × 10^?3 μg mL^?1 (bisphenol A diglycidyl ether) to 6.29 μg mL^?1 (diethylhexyl phthalate), while those of detection ranged from 0.068 × 10^?3 μg mL^?1 (bisphenol A diglycidyl ether) to 1.031 μg mL^?1 (diethylhexyl phthalate). To test method suitability, it was applied to real saliva and serum samples of healthy human volunteers and was found to meet the demands of the laboratories handling simple and relatively inexpensive equipment for screening oriented at rapid and reliable contamination assessment of a population.     

LC Determination of Phthalate Esters in Water Samples Using Continuous-Flow Microextraction

A novel method, continuous-flow microextraction (CFME) combined with liquid chromatography (LC) with variable-wavelength detector (VWD), has been developed for the determination of three phthalate esters (dimethyl phthalate (DMP), diethyl phthalate (DEP), and di-n-butyl phthalate (DnBP)) in water samples. Experimental parameters including extraction solvent, solvent drop volume, flow rate of sample solution, extraction time and ionic strength, which affected the extraction efficiency, were studied and optimized. Under the optimum extraction conditions, the method yields a linear calibration curve in the concentration range of 10–10,000 ng mL^?1 for target analytes. The enrichment factors of this method for DMP, DEP and DnBP reached at 27, 44 and 20, respectively, and the detection limits were 2, 1 and 5 ng mL^?1, respectively. Good repeatability of extraction was obtained with relative standard deviations below 8.6%. The results demonstrated that CFME followed by LC-VWD is a simple and reliable technique for the determination of phthalate esters in water samples.     

Detection of Phthalate Esters in Environmental Water Samples-Comparison of Nylon6 Nanofibers Mat-based Solid Phase Extraction and Other Conventional Extraction Methods

In this article, a new method for simultaneous determination of six phthalate esters was developed by a combination of electrospun nylon6 nanofibers mat‐based solid phase extraction with high performance liquid chromatography‐ultraviolet detector (HPLC‐UV). The six phthalate esters were dimethyl phthalate (DMP), diethyl phthalate (DEP), butyl benzyl phthalate (BBP), di‐n‐butyl phthalate (DBP), di‐(2‐ethylhexyl) phthalate (DEHP) and dioctyl phthalate (DOP). Under optimized conditions, all target analytes in 50 mL environmental water samples could be completely extracted by 2.5 mg nylon6 nanofibers mat and eluted by 100 µL solvent. Compared with C18 cartridges solid phase extraction, C18 disks solid phase extraction and national standard method (China), nylon6 nanofibers mat‐based solid phase extraction was advantageous in aspects of simple and fast operation, low consumption of extraction materials and organic solvents. The four methods were applied to analysis of environment water samples. All the results indicated that the determination values of target compounds with the proposed method were consistent with C18 cartridges and C18 disks solid phase extraction method, and the new method was better than the national standard method in aspects of recovery, LOD and precision. Therefore, nylon6 nanofibers mat has great potential as a novel material for solid phase extraction.     

Sequential Injection Lab‐on‐Valve Procedure for the Determination of Amantadine Using Potentiometric Methods

Amantadine potentiometric detectors were developed, evaluated and incorporated in a SIA‐LOV manifold in order to accomplish the control of pharmaceutical formulations and urine. The electrodes incorporate α‐cyclodextrin as ionophore, dibutyl phthalate or 2‐fluorophenyl 2‐nitrophenyl ether as plasticizers and potassium tetrakis[3,5‐bis‐(trifluoromethyl)phenyl]borate (KTFPB) as cationic additive. The slope increased from 61.2 to 63.8 mV decade^?1 and the practical limit of detection from 2.6×10^?6 mol L^?1 to 2.5×10^?5 mol L^?1 when the plasticizer was changed from 2‐fluorophenyl 2‐nitrophenyl ether to dibutyl phthalate. When incorporated in the flow‐manifold the membranes composed by dibutyl phthalate or with 2‐fluorophenyl 2‐nitrophenyl ether presented slopes and a practical limit of detection of 69.8 mV decade^?1 and 1.5×10^?4 mol L^?1 or 73.7 mV decade^?1 and 5.4×10^?5 mol L^?1, respectively. The electrode presented stable responses for over a year, and were highly selective concerning the representative species of the two sample matrices assayed as interferents. Comparison of obtained results with those provided by reference methods and recovery assays, revealed adequate accuracy for control assays.     

超声辅助分散液液微萃取-高效液相色谱测定水样中的4种邻苯二甲酸酯类增塑剂

建立了采用超声辅助分散液液微萃取技术结合高效液相色谱法(UA-DLLME-HPLC)对4种邻苯二甲酸酯(PAEs)进行富集、检测的方法,并成功应用于实际水样分析。实验中采用富集因子来评价萃取效率,考察并优化了影响萃取效率的主要因素,包括萃取剂类型和用量、分散剂类型和用量、超声时间、离子强度、萃取时间和pH值等。结果表明: 在最佳萃取条件下,该法对4种PAEs（邻苯二甲酸二甲酯、邻苯二甲酸二乙酯、邻苯二甲酸二丁酯和邻苯二甲酸二正辛酯）具有较高的富集能力,富集因子分别为71、144、169和159;检出限分别为3.78、1.77、3.07和3.30 μg/L。对实验室自来水、某品牌矿泉水以及湖水分别加标50、200及500 μg/L的回收率为82.99%～114.47%,相对标准偏差为1.93%～8.31%。该法简便、快速、环保,可以用于测定实际水样中的PAEs类增塑剂。     

养殖鱼邻苯二甲酸酯的含量分析

目的：为了解宁波地区淡水养殖鱼PAEs污染情况。方法采用液液超声萃取-气质联用法对宁波6个不同养殖点5种淡水养殖鱼体内8种邻苯二甲酸酯含量进行分析。结果宁波地区养殖鱼主要受 DMP、 DEP、 DBP、 DEHP 和 DOP 污染，质量分数最高可达134.1、258.9、249.2、830.8和5029μg/kg；草鱼、鳊鱼、鳙鱼、鲫鱼和乌鳢邻苯二甲酸污染指数PPI分别为9.999、9.735、13.97、8.945和5.809μg/kg。结论宁波地区淡水养殖鱼鱼体邻苯二甲酸酯含量与养殖环境有关，与鱼种无关。     

Application of dispersive liquid-liquid microextraction and high-performance liquid chromatography for the determination of three phthalate esters in water samples

A novel method, dispersive liquid-liquid microextraction (DLLME) coupled with high-performance liquid chromatography-variable wavelength detector (HPLC-VWD), has been developed for the determination of three phthalate esters (dimethyl phthalate (DMP), diethyl phthalate (DEP), and di-n-butyl phthalate (DnBP)) in water samples. A mixture of extraction solvent (41 μL carbon tetrachloride) and dispersive solvent (0.75 mL acetonitrile) were rapidly injected into 5.0 mL aqueous sample for the formation of cloudy solution, the analytes in the sample were extracted into the fine droplets of CCl₄. After extraction, phase separation was performed by centrifugation and the enriched analytes in the sedimented phase were determined by HPLC-VWD. Some important parameters, such as the kind and volume of extraction solvent and dispersive solvent, extraction time and salt effect were investigated and optimized. Under the optimum extraction condition, the method yields a linear calibration curve in the concentration range from 5 to 5000 ng mL⁻¹ for target analytes. The enrichment factors for DMP, DEP and DnBP were 45, 92 and 196, respectively, and the limits of detection were 1.8, 0.88 and 0.64 ng mL⁻¹, respectively. The relative standard deviations (R.S.D.) for the extraction of 10 ng mL⁻¹ of phthalate esters were in the range of 4.3-5.9% (n = 7). Lake water, tap water and bottled mineral water samples were successfully analyzed using the proposed method.     

Radical heterogeneous polymerization behavior of N‐methyl‐α‐fluoroacrylamide in benzene

The polymerization of N‐methyl‐α‐fluoroacrylamide (NMFAm) initiated with dimethyl 2,2′‐azobisisobutyrate (MAIB) in benzene was studied kinetically and with electron spin resonance. The polymerization proceeded heterogeneously with the highly efficient formation of long‐lived poly(NMFAm) radicals. The overall activation energy of the polymerization was 111 kJ/mol. The polymerization rate (R_p) at 50 °C is given by R_p = k[MAIB]^0.75±0.05 [NMFAm]^0.44±0.05. The concentration of the long‐lived polymer radical increased linearly with time. The formation rate (R_p?) of the long‐lived polymer radical at 50 °C is expressed by R_p? = k[MAIB]^1.0±0.1 [NMFAm]^0±0.1. The overall activation energy of the long‐lived radical formation was 128 kJ/mol, which agreed with the energy of initiation (129 kJ/mol), which was separately estimated. A comparison of R_p? with the initiation rate led to the conclusion that 1‐methoxycarbonyl‐1‐methylethyl radicals (primary radicals from MAIB), escaping from the solvent cage, were quantitatively converted into the long‐lived poly(NMFAm) radicals. Thus, this polymerization involves completely unimolecular termination due to polymer radical occlusion. ¹H NMR‐determined tacticities of resulting poly(NMFAm) were estimated to be rr = 0.34, mr = 0.48, and mm = 0.18. The copolymerization of NMFAm(M₁) and St(M₂) with MAIB at 50 °C in benzene gave monomer reactivity ratios of r₁ = 0.61 and r₂ = 1.79. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2196–2205, 2001     

Polythiophene/hexagonally ordered silica nanocomposite coating as a solid‐phase microextraction fiber for the determination of polycyclic aromatic hydrocarbons in water

A highly porous fiber coated with polythiophene/hexagonally ordered silica nanocomposite was prepared for solid‐phase microextraction (SPME). The prepared nanomaterial was immobilized onto a stainless‐steel wire for the fabrication of the SPME fiber. Polythiophene/hexagonally ordered silica nanocomposite fibers were used for the extraction of some polycyclic aromatic hydrocarbons from water samples. The extracted analytes were transferred to the injection port of a gas chromatograph using a laboratory‐designed SPME device. The results obtained prove the ability of the polythiophene/hexagonally ordered silica material as a new fiber for the sampling of organic compounds from water samples. This behavior is due most probably to the increased surface area of the polythiophene/hexagonally ordered silica nanocomposite. A one‐at‐a‐time optimization strategy was applied for optimizing the important extraction parameters such as extraction temperature, extraction time, ionic strength, stirring rate, and desorption temperature and time. Under the optimum conditions, the LOD of the proposed method is 0.1–3 pg/mL for analysis of polycyclic aromatic hydrocarbons from aqueous samples, and the calibration graphs were linear in a concentration range of 0.001–20 ng/mL (R² > 0.990) for most of the polycyclic aromatic hydrocarbons. The single fiber repeatability and fiber‐to‐fiber reproducibility were less than 8.6 and 19.1% (n = 5), respectively.     

A novel silver-coated solid-phase microextraction metal fiber based on electroless plating technique

A novel silver-coated solid-phase microextraction fiber was prepared based on electroless plating technique. Good extraction performance of the fiber for model compounds including phthalate esters (dibutyl phthalate, dioctyl phthalate, dicyclohexyl phthalate and diallyl phthalate) and polycyclic aromatic hydrocarbons (naphthalene, fluorene, phenanthrene, fluoranthene) in aqueous solution was obtained. Under the optimized conditions (extraction temperature, extraction time, ionic strength and desorption temperature), the proposed SPME-GC method showed wide linear ranges with correlation coefficients (R²) ranging from 0.9745 to 0.9984. The limits of detection were at the range of 0.02 to 0.1 μg L⁻¹. Single fiber repeatability and fiber-to-fiber reproducibility as well as stability to acid, alkali and high temperature were studied and the results were all satisfactory. The method was applied successfully to the aqueous extracts of disposable paper cup and instant noodle barrel. Several kinds of analytes were detected and quantified.     

Zeolite/Fe3O4 as a new sorbent in magnetic solid‐phase extraction followed by gas chromatography for determining phthalates in aqueous samples

In the present study, for the first time, we successfully employed zeolite/Fe₃O₄ as a new magnetic nanoparticle sorbent in magnetic solid‐phase extraction for determining phthalates in aqueous samples. Gas chromatography with flame ionization detection was used to detect the target analytes as a powerful instrumental analysis. Affecting parameters in the extraction process, including the amount of adsorbent, adsorption and desorption time, and volume of desorption solvent, were optimized using a response surface methodology based on central composite design. Under the optimum conditions, the linear range for dibutyl phthalate and bis(2‐ethylhexyl phthalate) was varied in the interval of 10–1700 and 10–1200 μg/L, respectively. Limits of detection were 2.80 μg/L for dibutyl phthalate and 3.20 μg/L for bis(2‐ethylhexyl phthalate). The recovery value for the extraction of target analytes was between 97 and 111%. The repeatability and reproducibility of the new proposed method were obtained: 10–13% and 13–13.5%, respectively. The increased sensitivity in using the proposed method has been demonstrated. Compared with previous methods, the new proposed method is an accurate, rapid, and reliable sample‐pretreatment method.