Size control synthesis of sulfur doped titanium dioxide （anatase） nanoparticles, its optical property and its photo catalytic reactivity for CO2 ＋ H2O conversion and phenol degradation

Sulfur doped anatase TiO2 nanoparticles (3 nm−12 nm) were synthesized by the reaction of titanium tetrachloride, water and sulfuric acid with addition of 3M NaOH at room temperature. The electro-optical and photocatalytic properties of the synthesized sulfur doped TiO2 nanoparticles were studied along with Degussa commercial TiO2 particles (24 nm). The results show that band gap of TiO2 particles decreases from 3.31 to 3.25 eV and for that of commercial TiO2 to 3.2 eV when the particle sizes increased from 3 nm to 12 nm with increase in sulfur doping. The results of the photocatalytic activity under UV and sun radiation show maximum phenol conversion at the particle size of 4 nm at 4.80% S-doping. Similar results are obtained using UV energy for both phenol conversion and conversion of CO2+H2O in which formation of methanol, ethanol and proponal is observed. Production of methanol is also achieved on samples with a particle size of 8 and 12 nm and sulfur doping of 4.80% and 5.26%. For TiO2 particle of 4 nm without S doping, the production of methanol, ethanol and proponal was lower as compared to the S-doped particles. This is attributed to the combined electronic effect and band gap change, S dopant, specific surface area and the light source used.     

Synthesis of Mg-Doped TiO2 nanoparticles under different conditions and its photocatalytic activity

In this study, TiO(2)- and Mg-doped TiO(2) nanoparticles with different dopant contents were prepared by sol-gel method. The prepared photocatalysts were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET) and diffuse reflectance spectroscopy (DRS) techniques. The results of BET analysis indicated a pore diameter of 8 nm and surface area of 48.5 m(2) g(-1). XRD patterns of pure and doped TiO(2) nanoparticles at 450 °C revealed that all phases are anatase. The particle size obtained from TEM was less than 20 nm. The band gap energy of Mg-doped TiO(2) nanoparticles was lower than that of TiO(2) . The photocatalytic activity of the pure and doped nanoparticles has been compared in the removal of C.I. Acid Red 27 (AR27). The photocatalytic activity of Mg-doped (0.2 mol%) TiO(2) for the degradation of AR27 was higher than that of bare TiO(2) nanoparticles. Results of total organic carbon analysis and changes in the AR27 UV-Vis peaks indicated 99% mineralization and extinguishing of all peaks in UV and visible regions is possible with Mg-doped TiO(2) nanoparticles. Removal efficiency of AR27 was sensitive to the parameters such as catalyst dose, pollutant concentration and light intensity.     

Wavelength-sensitive photocatalytic degradation of methyl orange in aqueous suspension over iron(III)-doped TiO2 nanopowders under UV and visible light irradiation

Well-crystallized iron(III)-doped TiO2 nanopowders with controlled Fe3+ doping concentration and uniform dopant distribution, have been synthesized with plasma oxidative pyrolysis. The photocatalytic reactivity of the synthesized TiO2 nanopowders with a mean particle size of 50-70 nm was quantified in terms of the degradation rates of methyl orange (MO) in aqueous TiO2 suspension under UV (mainly 365 and 316 nm) and visible light irradiation (mainly 405 and 436 nm). The photodecomposition of MO over TiO2 nanopowders followed a distinct two-stage pseudo first order kinetics. Interestingly, the photocatalytic reactivity depends not only on the iron doping concentration but also on the wavelength of the irradiating light. Under UV irradiation, nominally undoped TiO2 had much higher reactivity than Fe3+ -doped TiO2, suggesting that Fe3+ doping (> 0.05 at. %) in TiO2 with a mean particle size of approximately 60 nm was detrimental to the photocatalytic decomposition of methyl orange. Whereas, under visible light irradiation, the Fe3+ -doped TiO2 with an intermediate iron doping concentration of approximately 1 at. % had the highest photocatalytic reactivity due to the narrowing of band gap so that it could effectively absorb the light with longer wavelength. A strategy for improving the photocatalytic reactivity of Fe3+ -doped TiO2 used in the visible light region is also proposed.     

Interaction of Photoactive[Fe（CN）6]4^- with TiO2 Anatase（101） Surface： A Periodic Density Functional Theory Study

The plane-wave pseudopotential function method,based on density-functional theory,has been used to calculate the adsorption,electronic band structures,orbitals and optical absorption spectrum of [Fe(CN)6]4-on TiO2 anatase(101) surface. Our calculations reveal that the surface-modified anatase system has large adsorption energy and a much narrower band gap. [Fe(CN)6]4-adsorption on the (101) surface could lead to a large red shift of the anatase optical absorption threshold,which extends into a visible region significantly. The calculated results are in agreement with the experiment and other theoretical studies reasonably. It is very important for the understanding and further development of photovoltaic materials that are active under visible light.     

Vertically oriented TiO(x)N(y) nanopillar arrays with embedded Ag nanoparticles for visible-light photocatalysis

We present a straightforward method to produce highly crystalline, vertically oriented TiO(x)N(y) nanopillars (up to 1 μm in length) with a band gap in the visible-light region. This process starts with reactive dc sputtering to produce a TiN porous film, followed by a simple oxidation process at elevated temperatures in oxygen or air. By controlling the oxidation conditions, the band gap of the prepared TiO(x)N(y) can be tuned to different wavelength within the range of visible light. Furthermore, in order to inhibit carrier recombination to enhance the photocatalytic activity, Ag nanoparticles have been embedded into the nanogaps between the TiO(x)N(y) pillars by photoinduced reduction of Ag(+) (aq) irradiated with visible light. Transmission electron microscopy reveals that the Ag nanoparticles with a diameter of about 10 nm are uniformly dispersed along the pillars. The prepared TiO(x)N(y) nanopillar matrix and Ag:TiO(x)N(y) network show strong photocatalytic activity under visible-light irradiation, evaluated via degradation of Rhodamine B.     

Enhanced photocatalytic degradation of C.I. Basic Violet 2 using TiO2-SiO2 composite nanoparticles

In this report, TiO(2) -SiO(2) composite nanoparticles were prepared by the thermal hydrolysis method using titanium tetrachloride and tetraethylorthosilicate as TiO(2) and SiO(2) precursors, respectively. The prepared nanoparticles were characterized by X-ray powder diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), nitrogen adsorption/desorption and UV-Vis diffuse reflectance spectroscopy (DRS). The results indicated that, in comparison with pure TiO(2), TiO(2)-SiO(2) composite nanoparticles had a higher thermal stability, which prevents phase transformation from anatase to rutile. In addition, the TiO(2)-SiO(2) nanoparticles had a higher specific surface area, larger pore volume, greater band gap energy and smaller crystallite size. Thus, the surface area of TiO(2)-40% SiO(2) composite nanoparticles was about 17 times higher than that of pure TiO(2) nanoparticles. The photocatalytic activity of TiO(2)-SiO(2) composite nanoparticles in the photodegradation of C.I. Basic Violet 2 was investigated. The photodegradation rate of Basic Violet 2 using TiO(2)-40% SiO(2) nanoparticles calcined at 600°C was much faster than that using pure TiO(2) and Degussa P25 TiO(2) by 10.9 and 4.3 times, respectively. The higher photoactivity of the TiO(2)-SiO(2) composite nanoparticles was attributed to their higher surface area, larger pore volume, greater band-gap energy and smaller crystallite size compared with pure TiO(2).     

Electronic properties of the interface between p-CuI and anatase-phase n-TiO2 single crystal and nanoparticulate surfaces: a photoemission study

We present a study of the growth of the p-type inorganic semiconductor CuI on n-type TiO2 anatase single crystal (101) surfaces and on nanoparticulate anatase surfaces using synchrotron radiation photoemission spectroscopy. Core level photoemission data obtained using synchrotron radiation reveal that both the substrate (TiO2) and the overlayer (CuI) core levels shift to a lower binding energy to different degrees following the growth of CuI on TiO2. Valence band photoemission data show that the valence band maximum of the clean substrate differs from that of the dosed surface which may be interpreted qualitatively as due to the introduction of a new density of states within the band gap of TiO2 as a result of the growth of CuI. The valence band offset for the heterojunction n-TiO2p-CuI has been measured using photoemission for both nanoparticulate and single crystal TiO2 surfaces, and the band energy alignment for these heterojunction interfaces is presented. With the information obtained here, it is suggested that the interface between p-CuI and single crystal anatase-phase n-TiO2 is a type-II heterojunction interface, with significant band bending. The measured total band bending matches the work function change at the interface, i.e., there is no interface dipole. In the case of the nanoparticulate interface, an interface dipole is found, but band bending within the anatase nanoparticles remains quite significant. We show that the corresponding depletion layer may be accommodated within the dimension of the nanoparticles. The results are discussed in the context of the functional properties of dye-sensitized solid state solar cells.     

Interfacial electron transfer between the photoexcited porphyrin molecule and TiO2 nanoparticles: effect of catecholate binding

Interfacial electron transfer (ET) dynamics of 5,10,15-trisphenyl-20-(3,4-dihydroxybenzene) porphyrin (TPP-cat) adsorbed on TiO2 nanoparticles has been studied by femtosecond transient absorption spectroscopy in the visible and near-IR region exciting at 400 and 800 nm. TPP-cat molecule forms a charge transfer (CT) complex with TiO2 nanoparticles through the catechol moiety with the formation of a five-membered ring. Optical absorption measurements have shown that the Q-band of TPP-cat interacts strongly with TiO2 due to chelation; however, the Soret band is affected very little. Optical absorption measurements indicate that the catechol moiety also interacts with TiO2 nanoparticles showing the characteristic band of pure catechol-TiO2 charge transfer (CT) in the visible region. Electron injection has been confirmed by monitoring the cation radical, instant bleach, and injected electron in the conduction band of TiO2 nanoparticles. Electron injection time has been measured to be < 100 fs and recombination kinetics has been best fitted with a multiexponential function, where the majority of the injected electrons come back to the parent cation radical with a time constant of approximately 800 fs for both excitation wavelengths. However, the reaction channel for the electron injection process has been found to be different for both wavelengths. Excitation at 800 nm, found to populate the CT state of the Q-band, and from the photoexcited CT state electron injection into the conduction band, takes place through diffusion. On the other hand, with excitation at 400 nm, a complicated reaction channel takes place. Excitation with 400 nm light excites both the CT band of Cat-TiO2 and also the Soret band of TPP-cat. We have discussed the reaction path in the TPP-cat/TiO2 system after exciting with both 400 and 800 nm laser light. We have also compared ET dynamics by exciting at both wavelengths.     

Mechanisms and applications of plasmon-induced charge separation at TiO2 films loaded with gold nanoparticles

Plasmon-induced photoelectrochemistry in the visible region was studied at gold nanoparticle-nanoporous TiO(2) composites (Au-TiO(2)) prepared by photocatalytic deposition of gold in a porous TiO(2) film. Photoaction spectra for both the open-circuit potential and short-circuit current were in good agreement with the absorption spectrum of the gold nanoparticles in the TiO(2) film. The gold nanoparticles are photoexcited due to plasmon resonance, and charge separation is accomplished by the transfer of photoexcited electrons from the gold particle to the TiO(2) conduction band and the simultaneous transfer of compensative electrons from a donor in the solution to the gold particle. Besides its low-cost and facile preparation, a photovoltaic cell with the optimized electron mediator (Fe(2+/3+)) exhibits an optimum incident photon to current conversion efficiency (IPCE) of 26%. The Au-TiO(2) can photocatalytically oxidize ethanol and methanol at the expense of oxygen reduction under visible light; it is potentially applicable to a new class of photocatalysts and photovoltaic fuel cells.     

Facile design and nanostructural evaluation of silver-modified titania used as disinfectant

Fundamental research has been carried out to define optimal "green" synthesis conditions for the production of titania (TiO(2)) and silver (Ag) nanocomposites (TANCs) ranging from 12.7-22.8 nm in diameter. A bottom-up colloidal approach was employed to accurately control TANC monodispersity and composition. TANCs were found to be effective at inactivating Escherichia coli (E. coli) in water. The presence of Ag in the nanocomposites induced a decrease in TiO(2) band gap energy, which favoured valence to conduction band electron transfer and allowed for electron excitation using visible light. Aggregation of ultra-fine particles was prevented through the use of a long-chain polymer as evidenced by electrophoretic mobility studies. The TANCs catalyzed oxidation of bacterial membranes and cell death or disinfection. Theoretically, the TANC mode of E. coli disinfection is via water photolysis, which results in production of hydroxyl radicals and hydrogen peroxide. These interact with the outer membrane polysaccharides and lipids, leading to lipid peroxidation, membrane weakening and resulted in cell death. Our overarching goals were to optimize the variables involved in TANC "green" synthesis and to characterize its nanostructure. High resolution (HR) transmission and scanning electron microscopic (TEM and SEM) studies demonstrated that TANCs were highly crystalline and mono-dispersive. Elemental composition of Ag and Ti, as measured by X-ray energy dispersive (EDS) and X-ray photoelectron spectroscopy (XPS) confirmed sample purity. Ultraviolet-visible (UV-VIS) spectroscopy showed that the energy band-gap of Ag modified TiO(2) was in the visible range.     

P掺杂量对纳米TiO2结构及其光催化甘油水溶液制氢性能的影响

以钛酸丁酯为前驱体,以NaH2PO4为掺杂离子给体,采用溶胶-凝胶法制备了系列P掺杂的TiO2光催化剂,运用N2吸附-脱附、透射电子显微镜、X射线衍射、傅里叶变换红外吸收光谱、激光拉曼光谱、紫外-可见光漫反射等技术对催化剂进行了表征.结果表明,适量掺杂的P可以进入TiO2骨架中,而掺杂量过高时,P将溶解于TiO2晶格间隙中;P掺杂后的TiO2均为具有介孔结构的锐钛矿晶型纳米颗粒,其晶粒变小,分散度明显提高.适量P掺杂增大样品的比表面积,并使得TiO2禁带内引入杂质能级,降低了禁带能量,增加了光生电子和空穴的分离性能,提高了TiO2的吸光性能.光催化甘油水溶液制氢反应结果表明,P掺杂的TiO2表现出远高于纯TiO2的光催化活性;5%P掺杂样品在紫外光和模拟太阳光辐射下,其最高产氢速率可分别达1838和209μmol/(g.h).这与掺P后晶粒变小、比表面积增大、禁带能量降低以及光生电子和空穴的分离性能增加有关.     

Nitrogen and sulfur co-doped TiO2 nanosheets with exposed {001} facets: synthesis, characterization and visible-light photocatalytic activity

Nitrogen and sulfur co-doped TiO(2) nanosheets with exposed {001} facets (N-S-TiO(2)) were prepared by a simple mixing-calcination method using the hydrothermally prepared TiO(2) nanosheets powder as a precursor and thiourea as a dopant. The resulting samples were characterized by transmission electron microscope, X-ray diffraction, N(2) adsorption-desorption isotherms, X-ray photoelectron spectroscopy, and UV-Vis absorption spectroscopy. The electronic properties of N,S co-doped TiO(2) were studied using the first-principle density functional theory (DFT). The photocatalytic activity of N-S-TiO(2) was evaluated by degradation of 4-chlorophenol (4-CP) aqueous solution under visible light irradiation. The production of hydroxyl radicals (˙OH) on the surface of visible-light-irradiated samples was detected by photoluminescence technique using terephthalic acid as a probe molecule. The results show that nitrogen and sulfur atoms were successfully incorporated into the lattice of TiO(2), which resulted in N-S-TiO(2) samples exhibiting stronger absorption in the UV-visible range with a red shift in the band gap transition. The first-principle DFT calculations further confirm that N and S co-dopants can induce the formation of new energy levels in the band gap, which is associated with the response of N-S-TiO(2) nanosheets to visible light irradiation. Surprisingly, pure TiO(2) nanosheets show the visible-light photocatalytic activity for the degradation of 4-CP mainly due to the substrate-surface complexation of TiO(2) and 4-CP, which results in extending absorption of titania to visible light region through ligand-to-titanium charge transfer. The N-S-TiO(2) samples studied exhibited an enhanced visible-light photocatalytic activity than pure TiO(2). Especially, the doped TiO(2) sample at the nominal weight ratio of thiourea to TiO(2) powder of 2 showed the highest photocatalytic activity, which was about twice greater than that of Degussa P25. The enhanced activity of N-S-TiO(2) can be primarily attributed to the synergetic effects of two factors including the intense absorption in the visible-light region and the exposure of highly reactive {001} facets of TiO(2) nanosheets. The former is beneficial for the photogeneration of electrons and holes participating in the photocatalytic reactions, and the latter facilitates adsorption of 4-CP molecules on the surface of TiO(2) nanosheets.     

Observation of pH-dependent back-electron-transfer dynamics in alizarin/TiO2 adsorbates: importance of trap states

The dependence of the interfacial electron transfer in alizarin-sensitized TiO2 nanoparticles on the sample pH has been examined via transient absorbance spectroscopy in the visible spectral region (443-763 nm). Excitation of the alizarin/TiO2 system with visible pump pulses (lambdaexc = 500 nm) leads to a very fast electron injection (tauinj < 100 fs) over a wide pH range. Back electron transfer shows complicated multiphasic kinetics and strongly depends on the acidity of the solution. The strong dependence of back-electron-transfer dynamics on the ambient pH value is explained by a Nernstian-type change in the semiconductor band energy. Indeed, a variation of pH values over 7 units leads to a approximately 0.42 eV change of the conduction band edge position (i.e., the nominal free energy of the electron in the electrode). Assuming a pH-independent redox potential of the dye, this change was sufficient to push the system to a condition where direct photoinitiated electron injection to intraband gap surface states could be investigated. The existence of an electron-transfer pathway via surface trap states is supported by the similarity of the observed back-electron-transfer kinetics of alizarin/TiO2 at pH 9 and alizarin/ZrO2 reported in earlier work (J. Phys. Chem. B 2000, 104, 8995), where the conduction band edge is approximately 1 eV above the excited state of the dye. The influence of surface trap states on interfacial electron transfer has been studied, and a detailed analysis of their population, depopulation, and relaxation kinetics is performed. Therefore, alizarin adsorbed on the surface of TiO2 nanoparticles is an ideally suited system, where pH-dependent investigations allow a detailed study of the electron dynamics in trap states of TiO2 nanoparticles.     

Dye surface coating enables visible light activation of TiO2 nanoparticles leading to degradation of neighboring biological structures

Biologically and chemically modified nanoparticles are gaining much attention as a new tool in cancer detection and treatment. Herein, we demonstrate that an alizarin red S (ARS) dye coating on TiO2 nanoparticles enables visible light activation of the nanoparticles leading to degradation of neighboring biological structures through localized production of reactive oxygen species. Successful coating of nanoparticles with dye is demonstrated through sedimentation, spectrophotometry, and gel electrophoresis techniques. Using gel electrophoresis, we demonstrate that visible light activation of dye-TiO2 nanoparticles leads to degradation of plasmid DNA in vitro. Alterations in integrity and distribution of nuclear membrane associated proteins were detected via fluorescence confocal microscopy in HeLa cells exposed to perinuclear localized ARS-TiO2 nanoparticles that were photoactivated with visible light. This study expands upon previous studies that indicated dye coatings on TiO2 nanoparticles can serve to enhance imaging, by clearly showing that dye coatings on TiO2 nanoparticles can also enhance the photoreactivity of TiO2 nanoparticles by allowing visible light activation. The findings of our study suggest a therapeutic application of dye-coated TiO2 nanoparticles in cancer research; however, at the same time they may reveal limitations on the use of dye assisted visualization of TiO2 nanoparticles in live-cell imaging.     

近红外光驱动的UCNPs/ZnxCd1-xS纳米复合结构的化学合成并用于光化学还原六价铬

近红外光约占入射太阳能的 44% 以上, 为实现太阳能量的最大化利用, 近红外光 (NIR) 驱动的光催化技术成为科学研究的热点. 由于上转换荧光纳米材料 (UCNPs) 是优良的红外能量转换器, 合金半导体 ZnxCd1-xS 具有较好的化学稳定性以及生物相容性, 本文发展了一种简易的水热法, 将 UCNPs 和 ZnxCd1-xS 合金结合, 成功构建了 NIR 与可见光响应的核壳纳米结构. 由于这两种材料的晶格失配度较高, 很难直接外延生长, 我们通过引入非晶 TiO2将形成的催化剂纳米颗粒ZnxCd1-xS 紧紧束缚在 UCNPs 外面形成蛋黄-蛋壳结构, 在 NIR 光照下获得了较高的能量转换效率.首先, 在 UCNPs 外面外延生长一层 AA-Zn[(OH)4]2–复合物, 形成 UCNPs@AA-Zn[(OH)4]2–复合纳米结构, 然后在其核壳结构外面外延生长薄层的非晶 TiO2, 以稳定后续要制备的合金半导体 ZnxCd1-xS; 在水热条件下, UCNPs@AA-Zn[(OH)4]2–/TiO2与醋酸镉和硫脲反应, 形成 UCNPs@ZnxCd1-xS/TiO2复合材料. 在此, 我们选择β-NaYF4:Yb(30%),Tm(0.5%)@NaYF4:Yb(20%),Er(2%) 作为 NIR 的能量转换器. 样品的形貌、物相及化学组成分别采用场发射扫描电子显微镜、透射电子显微镜、X 射线衍射和原子吸收光谱法进行表征.研究表明, 我们成功制备了具有蛋黄-蛋壳结构的 UCNPs@ZnxCd1-xS/TiO2纳米颗粒. 此外, 非晶态 TiO2将 UCNPs 与ZnxCd1-xS 紧密结合, 对最终样品 UCNPs@ZnxCd1-xS 核壳纳米粒子的形成起到重要作用. 而且, 合金 ZnxCd1-xS 的化学组成可通过调整镉源和锌源的用量进行调节. 所制备的 UCNPs@ZnxCd1-xS 核壳纳米粒子在 NIR 光线或模拟太阳光照射下显示出高效的光化学还原 Cr(VI) 性能. 溶液中 70% 以上的 Cr(VI) 在 NIR 光照射 30 min 后被还原为 Cr(III). 本研究将为环境污水处理和太阳能利用提供一种可供选择的策略, 且所制的复合纳米结构在肿瘤治疗、药物释放和能量转换等领域也有着潜在的应用价值.     

Synthesis and characterization of sulfur-titanium dioxide nanocomposites for photocatalytic oxidation of cyanide using visible light irradiation

A sol-gel method was used to prepare TiO2and sulfur-TiO2(S-TiO2)nanocomposites, which were characterized by N2 adsorption-desorption, X-ray diffraction, X-ray photoelectron spectroscopy, photoluminescene, ultraviolet visible and transmission electron microscopy measurements. The photocatalytic performance of TiO2 and S-TiO2nanocomposites, with respect to the photocatalytic oxidation of cyanide under visible light irradiation, was determined. The results reveal that S is well dispersed on the surface of TiO2 nanoparticles. Additionally, the surface area of the S-TiO2nano-composites was observed to be smaller than that of the TiO2nanoparticles because of blocked pores caused by doping with S. The S-TiO2nanocomposite (0.3 wt% S) exhibited the lowest band gap and the highest photocatalytic activity in the oxidation of cyanide. The photocatalytic performance of S-TiO2(0.3 wt% S) nanocomposites was stable, even after the fifth reuse of the nanoparticles for the oxidation of cyanide.     

Standing wave enhancement of red absorbance and photocurrent in dye-sensitized titanium dioxide photoelectrodes coupled to photonic crystals

The light harvesting efficiency of dye-sensitized photoelectrodes was enhanced by coupling a TiO(2) photonic crystal layer to a conventional film of TiO(2) nanoparticles. In addition to acting as a dielectric mirror, the inverse opal photonic crystal caused a significant change in dye absorbance which depended on the position of the stop band. Absorbance was suppressed at wavelengths shorter than the stop band maximum and was enhanced at longer wavelengths. This effect arises from the slow group velocity of light in the vicinity of the stop band, and the consequent localization of light intensity in the voids (to the blue) or in the dye-sensitized TiO(2) (to the red) portions of the photonic crystal. By coupling a photonic crystal to a film of TiO(2) nanoparticles, the short circuit photocurrent efficiency across the visible spectrum (400-750 nm) could be increased by about 26%, relative to an ordinary dye-sensitized nanocrystalline TiO(2) photoelectrode.     

Extending photocatalytic activity of TiO2 nanoparticles to visible region of illumination by doping of cerium

Cerium-doped Titanium dioxide (TiO(2)) nanoparticles are prepared by sol-gel method. Doping shifts the UV absorption edge of TiO(2) to the visible region, making it efficient for visible light photocatalysis. Incorporation of cerium decreases the effective band gap of TiO(2) and increases the Urbach energy levels. At the dopant concentrations of 0.015 and 0.025 mol the luminescence intensity increases compared to undoped TiO(2); however, the luminescence is quenched at 0.035 mol. Quenching of luminescence indicates efficient separation of charge carriers. Undoped TiO(2) is showing poor performance in the photocatalytic degradation of methyl orange under visible light. However, on cerium doping its photoactivity is increased, and is drastically enhanced at 0.035 mol of cerium. Further increase in Ce(3+) doping level to 0.045 mol results in the reduction of the photodegradation of the dye. On UV irradiation, entire samples show good photocatalytic activity up to 30 min, but their efficiency decreases when irradiation time is increased to 45 min. Irradiation for longer time results in negative charging of the TiO(2) surface with migrating electrons. The negatively charged surface repels the OH(-) ion and O(2) molecule from adsorbing on its surface thus decreasing the availability of hydroxyl and superoxide radical for dye degradation.     

Non-Nernstian two-electron transfer photocatalysis at metalloporphyrin-TiO2 interfaces

A long-standing question in the photochemical sciences concerns how to integrate single-electron transfers to catalytic multielectron transfer reactions that produce useful chemical fuels. Here we provide a strategy for the two-electron formation of C-C bonds with molecular catalysts anchored to semiconductor nanocrystallites. The blue portion of the solar spectrum provides band gap excitation of the semiconductor while longer wavelengths of light initiate homolytic cleavage of metal-carbon bonds that, after interfacial charge transfer, restore the catalyst. The semiconductor utilized was the anatase polymorph of TiO(2) present as a nanocrystalline, mesoporous thin film. The catalyst was cobalt meso-5,10,15,20-tetrakis(4-carboxyphenyl)porphyrin chloride, Co(TCPP)Cl. For this catalyst and iron protoporphyrin IX chloride, Fe(PPIX)Cl, two distinct and sequential metal-based M(III/II) and M(II/I) reductions were observed under band gap illumination. Spectroelectrochemical characterization indicated that both reductions were non-Nernstian, behavior attributed to an environmentally dependent potential drop across the molecule-semiconductor interface. Reaction of Co(I)(TCPP)/TiO(2) with organobromides (RBr = 1-Br-hexane or benzyl bromide) resulted in the formation of Co(III)-R(TCPP)/TiO(2). Visible light excitation induced homolytic cleavage of the Co-C bond and the formation of C-C-bonded products. The reactions were catalytic when band gap excitation or an electrochemical bias provided TiO(2) electrons to the oxidized catalyst. Sustained photocurrents were quantified in photoelectrosynthetic solar cells under forward bias.     

Effect of Zr and C Co-doping on the Optical Properties and Electronic Structure of TiO_2

The systematic trends and effect introduced by Zr and C co-doping to TiO2 of electronic structure and optical properties of anatase TiO2 have been calculated by the plane-wave ultra-soft pseudopotential density functional theory (DFT) method within the generalized gradient approximation (GGA) for the exchange-correlation potential. Through the current calculations, the density of states (DOS), energy band structure and optical absorption coefficients have been obtained for TiO2 and compared with the doped TiO2, and the influence of electronic structure and optical properties caused by Zr and C co-doping has been presented qualitatively together. The results revealed that the energy band gap has been decreased owing to the doped Zr and C, whereas the optical absorption coefficients have been increased in the region of 400～800 nm and a red shift of absorption band can be found. Accordingly, photo catalytic activity of TiO2 has been enhanced. The current calculations are in good agreement with the experimental data.