新型树枝状PNP铬催化剂的合成及催化性能

以1.0代聚酰胺-胺(PAMAM)为配体骨架,氯代二苯基膦为原料,通过取代反应合成了1种含有较大空间位阻的新型树枝状PNP配体,再以Cr Cl3(THF)3为络合试剂,通过络合反应合成树枝状PNP铬催化剂.采用傅里叶变换红外光谱(FTIR)、紫外-可见分光光度计(UV-Vis)、核磁共振波谱(NMR)、电喷雾电离质谱(ESI-MS)和元素分析等手段证实合成的新型树枝状PNP配体及其铬催化剂的结构与理论设计的结构一致.以甲基铝氧烷(MAO)为助催化剂,对乙烯齐聚反应进行了研究,考察了溶剂种类、反应温度、反应压力及Al/Cr摩尔比对该催化剂活性和选择性的影响.结果表明,以甲苯为溶剂,MAO为助催化剂,当反应温度为25℃,反应压力为0.9 MPa,Al/Cr摩尔比为500时,该催化剂的活性高达2.15×105g/(mol Cr·h),催化剂对乙烯三聚、四聚反应的选择性共达到36.76%.     

Chromium(III) catalysed ethylene tetramerization promoted by bis(phosphino)amines with an N-functionalized pendant

Several N-functionalized bis(phosphino)amine ligands with ether, thioether and pyridyl tethers [(R')2PN(R')P(R')2=PNP] () have been synthesized. They react with CrCl3(THF)3 in CH2Cl2 to give dinuclear chloro bridged Cr2(micro-Cl)2Cl4(PNP)2 () which converts to the corresponding mononuclear solvento complexes fac-CrCl3(PNP)(NCR) (). The structures of the ligand with R'=-(CH2)3SCH3 and R'=Ph, and the complexes with R=CH3 () and C2H5 (), R'=-(CH2)3SCH3 and R'=Ph) have been established by single-crystal X-ray crystallography. All ligands are active towards ethylene tetramerization in the presence of Cr(III) and excess MAO at 80 degrees C in toluene. The ligand with thioether pendant Et2PN(CH2CH2CH2SCH3)PEt2 () shows the highest selectivity (55% weight in liquid product distribution) towards 1-octene. Complexes and are active towards ethylene polymerization under thermal conditions.     

Metallosupramolecular chemistry with bis(benzene-o-dithiolato) ligands

The bis(benzene-o-dithiol) ligands H(4)-1, H(4)-2, and H(4)-3 react with [Ti(OC(2)H(5))(4)] to give dinuclear triple-stranded helicates [Ti(2)L(3)](4)(-) (L = 1(4)(-), 2(4)(-), 3(4)(-)). NMR spectroscopic investigations revealed that the complex anions possess C(3) symmetry in solution. A crystal structure analysis for (PNP)(4)[Ti(2)(2)(3)] ((PNP)(4)[14]) confirmed the C(3) symmetry for the complex anion in the solid state. The complex anion in Li(PNP)(3)[Ti(2)(1)(3)] (Li(PNP)(3)[13]) does not exhibit C(3) symmetry in the solid state due to the formation of polymeric chains of lithium bridged complex anions. Complexes [13](4)(-) and [14](4)(-) were obtained as racemic mixtures of the Delta,Delta and Lambda,Lambda isomers. In contrast to that, complex (PNP)(4)[Ti(2)(3)(3)] ((PNP)(4)[15]) with the enantiomerically pure chiral ligand 3(4)(-) shows a strong Cotton effect in the CD spectrum, indicating that the chirality of the ligands leads to the formation of chiral metal centers. The o-phenylene diamine bridged bis(benzene-o-dithiol) ligand H(4)-4 reacts with Ti(4+) to give the dinuclear double-stranded complex Li(2)[Ti(2)(4)(2)(mu-OCH(3))(2)] containing two bridging methoxy ligands between the metal centers. The crystal structure analysis and the (1)H NMR spectrum of (Ph(4)As)(2)[Ti(2)(4)(2)(mu-OCH(3))(2)] ((Ph(4)As)(2)[(16]) reveal C(2) symmetry for the anion [Ti(2)(4)(2)(mu-OCH(3))(2)](2)(-). For a comparative study the dicatechol ligand H(4)-5, containing the same o-phenylene diamine bridging group as the bis(benzene-o-dithiol) ligands H(4)-4, was prepared and reacted with [TiO(acac)(2)] to give the dinuclear complex anion [Ti(2)(5)(2)(mu-OCH(3))(2)](2)(-). The molecular structure of (PNP)(2)[Ti(2)(5)(2)(mu-OCH(3))(2)] ((PNP)(2)[17]) contains a complex anion which is similar to [16](2)(-), with the exception that strong N-H...O hydrogen bonds are formed in complex anion [17](2)(-), while N-H...S hydrogen bonds are absent in complex anion [16](2)(-).     

Metal-ligand cooperation in C-H and H2 activation by an electron-rich PNP Ir(I) system: facile ligand dearomatization-aromatization as key steps

Unusual reactions are reported, in which the aromatic PNP ligand (PNP = 2,6-bis-(di-tert-butylphosphinomethyl)pyridine) acts in concert with the metal in the activation of H2 and benzene, via facile aromatization/dearomatization processes of the ligand. A new, dearomatized electron-rich (PNP*)Ir(I) complex 2 (PNP* = deprotonated PNP) activates benzene to form the aromatic (PNP)Ir(I)Ph 4, which upon treatment with CO undergoes a surprising oxidation process to form (PNP*)Ir(III)(H)CO 6, involving proton migration from the ligand "arm" to the metal, with concomitant dearomatization. 4 undergoes stereoselective activation of H2 to exclusively form the trans-dihydride 7, rather than the expected cis-dihydride complex. Our evidence, including D-labeling, suggests the possibility that the Ir(I)-Ph complex is transformed to the dearomatized Ir(III)(Ph)(H) (independently prepared at low temperature), which may be the actual intermediate undergoing H2 activation.     

Helical complexes containing diamide-bridged benzene-o-dithiolato/catecholato ligands

The benzene-o-dithiol/catechol ligands H4-2 and H4-3 react with [TiO(acac)2] to give the dinuclear, double-stranded anionic complexes [Ti2(L)2(mu-OCH3)2](2-) ([22](2-), L=2(4-); [23](2-), L=3(4-)). NMR spectroscopic investigations reveal that the complex anion [Ti2(2)2(mu-OCH3)(2)](2-) is formed as a mixture of three of four possible isomers/pairs of enantiomers, whereas only one isomer of the complex anion [Ti2(3)2(mu-OCH3)(2)](2-) is obtained. The crystal structure analysis of (PNP)2[Ti2(3)2(mu-OCH3)2] shows a parallel orientation of the ligand strands, whereas the structure determination for (AsPh4)2[Ti2(2)2(mu-OCH3)2] does not yield conclusive results about the orientation of the ligand strands due the presence of different isomers in solution, the possible co-crystallisation of different isomers and severe disorder in the crystal. NMR spectroscopy shows that ligand H4-3 reacts at elevated temperature with [TiO(acac)2] to give the triple-stranded helicate (PNP)4[Ti2(3)3] ((PNP)4[24]) as a mixture of two isomers, one with a parallel orientation of the ligand strands and one with an antiparallel orientation. Exclusively the triple-stranded helicates [Ti2(L)(3)](4-) ([25](4-), L=1(4-); [26](2-), L=4(4-)) are formed in the reaction of ligands H4-1 and H4-4 with [TiO(acac)2]. The molecular structures of Na(PNP)3[Ti2(1)3]CH(3)OHH(2)OEt(2)O (Na(PNP)3[25]CH(3)OHH(2)OEt(2)O) and Na(1.5)(PNP)(6.5)[Ti2(4)3]2.3 DMF (Na(1.5)(PNP)(6.5)[26]2.3 DMF) reveal a parallel orientation of the ligand strands in both complexes, which is retained in solution. The sodium cations present in the crystal structures lead to two different kinds of aggregation in the solid state. Na-[25]-Na-[25]-Na polymeric chains are formed from compound Na(PNP)3[25], with the sodium cations coordinated by the carbonyl groups of two ligand strands from two different [Ti2(1)3](4-) ions in addition to solvent molecules. In contrast to this, two [Ti2(4)3](4-) ions are connected by a sodium cation that is coordinated by the three meta oxygen atoms of the catecholato groups of each complex tetraanion to form a central {NaO6} octahedron in the anionic pentanuclear complex {[26]-Na-[26]}(7-).     

Intermolecular C-H bond activation promoted by a titanium alkylidyne

The transient titanium alkylidyne complex (PNP)TiCtBu (PNP = N-[2-P(CHMe2)2-4-methylphenyl]2-), prepared from alpha-hydrogen abstraction of the corresponding alkylidene-alkyl species (PNP)Ti=CHtBu(CH2tBu), can readily undergo intermolecular 1,2-addition of C-H bonds of benzene and SiMe4. Synthesis and reactivity, isotopic labeling, kinetics, and theoretical studies strongly favor an alkylidyne pathway and the alpha-H abstraction step to be the rate-determining step.     

Room temperature ring-opening metathesis of pyridines by a transient Ti[triple bond]C linkage

The transient titanium alkylidyne complex (PNP)TiCtBu (PNP = N[2-P(CHMe2)2-4-methylphenyl]2-), prepared from alpha-hydrogen abstraction of the corresponding alkylidene-alkyl species (PNP)Ti=CHtBu(CH2tBu), can readily cleave the C-N bond of N-heterocycles such as pyridine and 4-picoline at room temperature to afford azametallabicyclic systems. Experimental and theoretical studies strongly favor a ring-opening metathesis pathway where [2 + 2] cycloaddition of pyridine across the TiC linkage ultimately leads to C-N bond rupture.     

New anilinotropone-based titanium complexes: synthesis, characterization and application as catalysts for olefin polymerization

New titanium(IV) dichloride complexes containing 2-anilinotropone ligands have been synthesized and characterized. Bis(ligand)titanium dichloride complexes 1 and 2 were synthesized from reaction of TiCl4(THF)2 with 2 equivalents of the corresponding sodium salts of 2-(2,6-diisopropylanilino)tropone (L1) and 2-(2,3,4,5,6-pentafluoroanilino)tropone (L2), respectively. The mixed cyclopentadienyl-anilinotropone compound 3 was synthesized by reaction of the lithium salt of with CpTiCl3. The Cp-mixed micro-O bimetallic complex 4 was also isolated as a by-product owing to the adventitious presence of moisture. The molecular structures 1-4 of have been determined by single-crystal X-ray diffraction studies. Complexes 1 and 2 are isostructural and exhibit a C2-symmetric octahedral geometry, with a trans(N,N), cis(O,O) arrangement in complex 1, but with a trans(O,O), cis(N,N) arrangement in complex 2. The Cp-mixed complex 3 has a distorted square-pyramidal structure with the Cp ligand in the apical position. Bimetallic complex 4 shows a similar coordination geometry for the five-coordinate titanium atom and a pseudo-tetrahedral coordination for the second metallic centre. All new complexes, when activated with methylaluminoxane, are active in the polymerization of ethylene and propene.     

Preparation, structure, and ethylene (co)polymerization behavior of Group IV metal complexes with an [OSSO]-carborane ligand

The synthesis of Group IV metal complexes that contain a tetradentate dianionic [OSSO]-carborane ligand [(HOC(6)H(2)tBu(2)-4,6)(2)(CH(2))(2)S(2)C(2 (B(10)H(10))] (1a) is described. Reactions of TiCl(4) and Ti(OiPr)(4) with the [OSSO]-type ligand 1a afford six-coordinated titanium complex [Ti(OC(6)H(2)tBu(2)-4,6)(2)(CH(2))(2)S(2)C(2)(B(10)H(10))Cl(2)] (2a) and four-coordinated titanium complex [Ti(OC(6)H(2)tBu(2)-4,6)(2)(CH(2))(2)S(2)C(2)(B(10)H(10))(OiPr)(2)] (2b), respectively. ZrCl(4) and HfCl(4) were treated with 1a to give six-coordinated zirconium complex [Zr(OC(6)H(2)tBu(2)-4,6)(2)(CH(2))(2)S(2)C(2)(B(10)H(10))Cl(2) (thf)(2)] (2c) and six-coordinated hafnium complex [Hf(OC(6)H(2)tBu(2)-4,6)(2)(CH(2))(2)S(2)C(2)(B(10)H(10))Cl(2)] (2d). All the complexes were fully characterized by IR, NMR spectroscopy, and elemental analysis. In addition, X-ray structure analyses were performed on complexes 2a and 2b and reveal the expected different coordination geometry due to steric hindrance effects. Extended X-ray absorption fine structure (EXAFS) spectroscopy was performed on complexes 2c and 2d to describe the coordination chemistry of this ligand around Zr and Hf. Six-coordinated titanium complex 2a showed good activity toward ethylene polymerization as well as toward copolymerization of ethylene with 1-hexene in the presence of methylaluminoxane (MAO) as cocatalyst (up to 1060 kg[mol(Ti)](-1) h(-1) in the case of 10 atm of ethylene pressure).     

Competitive C-I versus C-CN reductive elimination from a Rh(III) complex. Selectivity is controlled by the solvent

The RhIII complex [(PNP)Rh(CN)(CH3)][I] 5, obtained by oxidative addition of methyl iodide to [(PNP)Rh(CN)] 2, reacts selectively in two pathways: In aprotic solvents C-I reductive elimination of methyl iodide followed by its electrophilic attack on the cyano ligand takes place, giving the methyl isonitrile RhI complex [(PNP)Rh(CNCH3)][I] 3, while in protic solvents C-C reductive elimination of acetonitrile takes place forming an iodo RhI complex [(PNP)RhI] 9. Reaction of 2 with ethyl iodide in aprotic solvents gave the corresponding isonitrile complex, while in protic solvents no reactivity was observed. The selectivity of this reaction is likely due to a hydrogen bond between the cyano ligand and the protic solvent, as observed by X-ray diffraction, which retards electrophilic attack on this ligand.     

Lewis acid stabilized methylidene and oxoscandium complexes

The methylidene scandium complex (PNP)Sc(mu3-CH2)(mu2-CH3)2[Al(CH3)2]2 (PNP = N[2-P(CHMe2)2-4-methylphenyl]2-) can be prepared from the reaction of (PNP)Sc(CH3)2 and 2 equiv of Al(CH3)3. The Lewis acid stabilized methylidenes candium complex has been crystallographically characterized, and its bonding scheme analyzed by DFT. In addition, we report preliminary reactivity studies of the Sc-CH2 ligand with substrates such as H2NAr and OCPh2. While the former results in an Br?nsted acid-base reaction, the latter reagent produces the olefin H2C CPh2 along with the novel oxoscandium complex (PNP)Sc(mu3-O)(mu2-CH3)2[Al(CH3)2]2, quantitatively.     

Ni(Et2PCH2NMeCH2PEt2)2]2+ as a functional model for hydrogenases

The reaction of Et(2)PCH(2)N(Me)CH(2)PEt(2) (PNP) with [Ni(CH(3)CN)(6)](BF(4))(2) results in the formation of [Ni(PNP)(2)](BF(4))(2), which possesses both hydride- and proton-acceptor sites. This complex is an electrocatalyst for the oxidation of hydrogen to protons, and stoichiometric reaction with hydrogen forms [HNi(PNP)(PNHP)](BF(4))(2), in which a hydride ligand is bound to Ni and a proton is bound to a pendant N atom of one PNP ligand. The free energy associated with this reaction has been calculated to be -5 kcal/mol using a thermodynamic cycle. The hydride ligand and the NH proton undergo rapid intramolecular exchange with each other and intermolecular exchange with protons in solution. [HNi(PNP)(PNHP)](BF(4))(2) undergoes reversible deprotonation to form [HNi(PNP)(2)](BF(4)) in acetonitrile solutions (pK(a) = 10.6). A convenient synthetic route to the PF(6)(-) salt of this hydride involves the reaction of PNP with Ni(COD)(2) to form Ni(PNP)(2), followed by protonation with NH(4)PF(6). A pK(a) of value of 22.2 was measured for this hydride. This value, together with the half-wave potentials of [Ni(PNP)(2)](BF(4))(2), was used to calculate homolytic and heterolytic Ni-H bond dissociation free energies of 55 and 66 kcal/mol, respectively, for [HNi(PNP)(2)](PF(6)). Oxidation of [HNi(PNP)(2)](PF(6)) has been studied by cyclic voltammetry, and the results are consistent with a rapid migration of the proton from the Ni atom of the resulting [HNi(PNP)(2)](2+) cation to the N atom to form [Ni(PNP)(PNHP)](2+). Estimates of the pK(a) values of the NiH and NH protons of these two isomers indicate that proton migration from Ni to N should be favorable by 1-2 pK(a) units. Cyclic voltammetry and proton exchange studies of [HNi(depp)(2)](PF(6)) (where depp is Et(2)PCH(2)CH(2)CH(2)PEt(2)) are also presented as control experiments that support the important role of the bridging N atom of the PNP ligand in the proton exchange reactions observed for the various Ni complexes containing the PNP ligand. Similarly, structural studies of [Ni(PNBuP)(2)](BF(4))(2) and [Ni(PNP)(dmpm)](BF(4))(2) (where PNBuP is Et(2)PCH(2)N(Bu)CH(2)PEt(2) and dmpm is Me(2)PCH(2)PMe(2)) illustrate the importance of tetrahedral distortions about Ni in determining the hydride acceptor ability of Ni(II) complexes.     

Synthesis and application of chromium complexes bearing hyperbranched PNP ligands in the ethylene oligomerization

Series of hyperbranched PNP ligands ( L1 – L3 ) were prepared using three low-generation hyperbranched molecules with the same branching chains and functional groups but different alkyl chain length as backbones in a mixed solvent of acetonitrile and dichloromethane. The chromium complexes ( Cr1 – Cr3 ) were obtained by reacting with CrCl₃(THF)₃ and the corresponding ligands ( L1 – L3 ). Both L1 – L3 and Cr1 – Cr3 were characterized by elemental analysis, Fourier transform infrared and electrospray ionization–mass spectrometry as well as ¹H nuclear magnetic resonance (NMR) and ³¹P NMR measurements in the case of the ligands. When activated with different aluminum co-catalysts, all three chromium complexes were able to catalyze the ethylene oligomerization, but the products of the ethylene oligomerization were mainly dependent on ethylene pressure, co-catalyst and ligand backbone. Upon activation with methylaluminoxane, the catalytic activity and the selectivity of C8 olefin increased with increasing of ethylene pressure for Cr1 , the catalytic activity was 13.83 × 10⁵ g·(mol Cr·h)⁻¹ and the main product was C8 olefin (50.68%) at the ethylene pressure of 4.0 MPa. When activated with diethylaluminium chloride, ethylaluminium dichloride and ethylaluminum sesquichloride, Cr1 showed the lower catalytic activity and the higher selectivity of C4 olefin in toluene. An increase in the length of alkyl chain in the hyperbranched PNP ligand backbone caused a decrease in the catalytic activity and an increase in the selectivity of C8 + olefin. The PNP chromium complexes exhibited higher selectivity for higher carbon number olefins compared with the dendritic PNP chromium complex ( Cr5 ).     

Bis(diisopropylphosphino)pyridine iron dicarbonyl, dihydride, and silyl hydride complexes

Treatment of the bis(diisopropylphosphino)pyridine iron dichloride, ((iPr)PNP)FeCl2 ((iPr)PNP = 2,6-(iPr2PCH2)2(C5H3N)), with 2 equiv of NaBEt3H under an atmosphere of dinitrogen furnished the diamagnetic iron(II) dihydride dinitrogen complex, ((iPr)PNP)FeH2(N2). Addition of 1 equiv of PhSiH3 to ((iPr)PNP)FeH2(N2) resulted in exclusive substitution of the hydride trans to the pyridine to yield the silyl hydride dinitrogen compound, ((iPr)PNP)FeH(SiH2Ph)N2, which has been characterized by X-ray diffraction. The solid-state structure established a distorted octahedral geometry where the hydride ligand distorts toward the iron silyl. Both ((iPr)PNP)FeH2(N2) and ((iPr)PNP)FeH(SiH2Ph)N2 form eta2-dihydrogen complexes upon exposure to H2. The iron hydrides and the eta2-H2 ligands are in rapid exchange in solution, consistent with the previously reported "cis" effect, arising from a dipole/induced dipole interaction between the two ligands. Taken together, the spectroscopic, structural, and reactivity studies highlight the relative electron-donating ability of this pincer ligand as compared to the redox-active aryl-substituted bis(imino)pyridines.     

Silver(I) and thallium(I) complexes of a PNP ligand and their utility as PNP transfer reagents

Silver(I) and thallium(I) complexes of a diarylamido-based PNP pincer ligand have been prepared and characterized. The silver complex [(PNP)Ag]2 exists as a dimer both in solution and in the solid state and is stable under an ambient atmosphere. Thallium complex (PNP)Tl is, however, monomeric and acutely sensitive to moisture and air. Both reagents serve to transfer PNP into the coordination sphere of divalent nickel, palladium, and platinum. [(PNP)Ag]2 is able to effect PNP transfer in air, but the transfer to nickel(II) is less efficient than that with the thallium(I) analogue.     

Intermolecular C-H bond activation reactions promoted by transient titanium alkylidynes. Synthesis, reactivity, kinetic, and theoretical studies of the Ti[triple bond]C linkage

The neopentylidene-neopentyl complex (PNP)Ti=CH(t)Bu(CH2(t)Bu) (2; PNP(-) = N[2-P(CHMe2)(2-)4-methylphenyl]2), prepared from the precursor (PNP)Ti[triple bond]CH(t)Bu(OTf) (1) and LiCH2(t)Bu, extrudes neopentane in neat benzene under mild conditions (25 degrees C) to generate the transient titanium alkylidyne, (PNP)Ti[triple bond]C(t)Bu (A), which subsequently undergoes 1,2-CH bond addition of benzene across the Ti[triple bond]C linkage to generate (PNP)Ti=CH(t)Bu(C6H5) (3). Kinetic, mechanistic, and theoretical studies suggest the C-H activation process to obey pseudo-first-order in titanium, the alpha-hydrogen abstraction to be the rate-determining step (KIE for 2/2-d(3) conversion to 3/3-d(3) = 3.9(5) at 40 degrees C) with activation parameters DeltaH = 24(7) kcal/mol and DeltaS = -2(3) cal/mol.K, and the post-rate-determining step to be C-H bond activation of benzene (primary KIE = 1.03(7) at 25 degrees C for the intermolecular C-H activation reaction in C6H6 vs C6D6). A KIE of 1.33(3) at 25 degrees C arose when the intramolecular C-H activation reaction was monitored with 1,3,5-C6H3D3. For the activation of aromatic C-H bonds, however, the formation of the sigma-complex becomes rate-determining via a hypothetical intermediate (PNP)Ti[triple bond]C(t)Bu(C6H5), and C-H bond rupture is promoted in a heterolytic fashion by applying standard Lewis acid/base chemistry. Thermolysis of 3 in C6D6 at 95 degrees C over 48 h generates 3-d(6), thereby implying that 3 can slowly equilibrate with A under elevated temperatures with k = 1.2(2) x 10-5 s(-1), and with activation parameters DeltaH = 31(16) kcal/mol and DeltaS = 3(9) cal/mol x K. At 95 degrees C for one week, the EIE for the 2 --> 3 reaction in 1,3,5-C6H3D3 was found to be 1.36(7). When 1 is alkylated with LiCH2SiMe3 and KCH2Ph, the complexes (PNP)Ti=CHtBu(CH2SiMe3) (4) and (PNP)Ti=CHtBu(CH2Ph) (6) are formed, respectively, along with their corresponding tautomers (PNP)Ti=CHSiMe3(CH2tBu) (5) and (PNP)Ti=CHPh(CH2tBu) (7). By means of similar alkylations of (PNP)Ti=CHSiMe3(OTf) (8), the degenerate complex (PNP)Ti=CHSiMe3(CH2SiMe3) (9) or the non-degenerate alkylidene-alkyl complex (PNP)Ti=CHPh(CH2SiMe3) (11) can also be obtained, the latter of which results from a tautomerization process. Compounds 4/5 and 9, or 6/7 and 11, also activate benzene to afford (PNP)Ti=CHR(C6H5) (R = SiMe3 (10), Ph (12)). Substrates such as FC6H5, 1,2-F2C6H4, and 1,4-F2C6H4 react at the aryl C-H bond with intermediate A, in some cases regioselectively, to form the neopentylidene-aryl derivatives (PNP)Ti=CHtBu(aryl). Intermediate A can also perform stepwise alkylidene-alkyl metatheses with 1,3,5-Me3C6H3, SiMe4, 1,2-bis(trimethylsilyl)alkyne, and bis(trimethylsilyl)ether to afford the titanium alkylidene-alkyls (PNP)Ti=CHR(R') (R = 3,5-Me2C6H2, R' = CH2-3,5-Me2C6H2; R = SiMe3, R' = CH2SiMe3; R = SiMe2CCSiMe3, R' = CH2SiMe2CCSiMe3; R = SiMe2OSiMe3, R' = CH2SiMe2OSiMe3).     

Coordinated olefins as incipient carbocations: catalytic codimerization of ethylene and internal olefins by a dicationic Pt(II)-ethylene complex

The coordinated ethylene molecule in the dicationic complex [(PNP)Pt(CH2=CH2)](BF4)2 (PNP = 2,6-bis(diphenylphosphinomethyl)pyridine) undergoes nucleophilic attack by free internal alkenes, giving the isolable complexes [(PNP)Pt(CH2=CHCH(Me)CMeRR'](BF4)2 (R, R' = H, Me) and providing a new effective pathway for a chemo- and regio-selective catalytic hydrovinylation reaction.     

Metal (Mg, Fe, Co, Zr and Ti) complexes derived from aminosilyl substituted aminopyridinato ligand: synthesis, structures and ethylene polymerization behaviors of the group 4 complexes

Lithium N-[(N,N-dimethylamino)dimethylsilyl]-2-pyridylamidate (2) was prepared from the reaction of new compound N-[(N,N-dimethylamino)dimethylsilyl]-2-pyridylamine (1) and LiBu(n). Treatment of the lithium salt (2) with an equal equivalent of MgBr(2)(THF)(2), FeCl(2) and CoCl(2) afforded the corresponding dinuclear complexes , , and , in which metal atoms possess similar trigonal bipyramidal geometries and each ligand functions as a bimetallic bridging binding aminopyridinato moiety with N-donation from the dimethylamino group. While the stoichiometric reaction of with ZrCl(4) gave the mononuclear zirconium complex (6); the seven coordinated zirconium atom adopts a distorted pentagonal bipyramid geometry and the ligand acts as monoanionic η(2)-aminopyridinato moiety with the pendant arm coordinated via N(CH(3))(2). The reaction of with one equivalent of TiCl(4)(THF)(2) produced the interesting dinuclear titanium complex (7) owing to the elimination of a (N,N-dimethylamino)dimethylsilyl group from the original ligand, and the two titanium centers present different coordination geometries. The molecular structures of the crystalline metal complexes have been confirmed by X-ray single crystal diffraction analysis. Upon activation with methylaluminoxane (MAO), both complexes and exhibited moderate catalytic activities toward ethylene polymerization and produced high molecular weight polyethylenes with broad molecular weight distributions.     

Pendant bases as proton relays in iron hydride and dihydrogen complexes

The complex trans-[HFe(PNP)(dmpm)(CH(3)CN)]BPh(4), 3, (where PNP is Et(2)PCH(2)N(CH(3))CH(2)PEt(2) and dmpm is Me(2)PCH(2)PMe(2)) can be successively protonated in two steps using increasingly strong acids. Protonation with 1 equiv of p-cyanoanilinium tetrafluoroborate in acetone-d(6) at -80 degrees C results in ligand protonation and the formation of endo (4a) and exo (4b) isomers of trans-[HFe(PNHP)(dmpm)(CH(3)CN)](BPh(4))(2). The endo isomer undergoes rapid intramolecular proton/hydride exchange with an activation barrier of 12 kcal/mol. The exo isomer does not exchange. Studies of the reaction of 3 with a weaker acid (anisidinium tetrafluoroborate) in acetonitrile indicate that a rapid intermolecular proton exchange interconverts isomers 4a and 4b, and a pK(a) value of 12 was determined for these two isomers. Protonation of 3 with 2 equiv of triflic acid results in the protonation of both the PNP ligand and the metal hydride to form the dihydrogen complex [(H(2))Fe(PNHP)(dmpm)(CH(3)CN)](3+), 11. Studies of related complexes [HFe(PNP)(dmpm)(CO)](+) (12) and [HFe(depp)(dmpm)(CH(3)CN)](+) (10) (where depp is bis(diethylphosphino)propane) confirm the important roles of the pendant base and the ligand trans to the hydride ligand in the rapid intra- and intermolecular hydride/proton exchange reactions observed for 4. Features required for an effective proton relay and their potential relevance to the iron-only hydrogenase enzymes are discussed.     

A highly emissive Cu2N2 diamond core complex supported by a [PNP]- ligand

A Cu2N2 diamond core structure, {(PNP)CuI}2 (2), supported by a [PNP]- ligand (1) ([PNP]- = bis(2-(diisobutylphosphino)phenyl)amide) has been prepared. 2 is highly emissive at ambient temperature in both the solid and solution states and is characterized by a relatively long-lived excited state (tau > 10 mus) and an unusually high quantum yield (phi > 0.65). These observations are consistent with a low degree of structural reorganization between the ground state of 2 and its excited state *2, and also with a high degree of steric protection of the two copper centers of 2 afforded by the bulky [PNP]- ligand. An estimate for the excited-state reduction potential of *2 (ca. -3.2 V vs Fc+/Fc), and the availability of two well-separated and reversible ground-state redox processes, suggests that bimetallic copper systems of these types may be interesting candidates to consider for photochemically driving multielectron redox transformations.