共查询到20条相似文献,搜索用时 31 毫秒
1.
采用交错双栅结构,结合带状电子注,研究了一种工作在140 GHz频段的大功率行波管. 本振模数值计算表明该结构具有良好的色散特性和耦合阻抗.针对所采用的慢波结构, 提出了慢波过渡结构、输入输出耦合器和集中衰减器,保证了行波管的良好工作. 利用三维大信号模拟计算的方法得到的结果显示,当电子注直流功率为5.115 kW,输入信号功率为0.1 W时, 所研究的行波管能在132-152 GHz范围内提供大于300 W的峰值功率,其中在138 GHz时得到最大功率546 W, 对应增益为37.37 dB.当在0.027-0.46 W内调节输入信号功率,可以保持该行波管在128-152 GHz 频带内得到大于440 W的峰值功率,对应的电子效率大于8.6%. 结果显示该行波管将在大功率短毫米波领域具有重要意义和潜在应用价值. 相似文献
2.
斜注管是返波振荡器的一种,通过电子注的倾斜,电子距离慢波结构更近,高频场更强,耦合阻抗和互作用效率更高,显著增加输出功率。对带状注斜注管的互作用系统进行了设计,并首次将双排齿慢波结构应用于斜注管。利用电磁模拟软件和3D粒子模拟软件对设计的斜注管的色散曲线和场分布进行了分析,并对其注-波互作用进行了模拟,可以得到大于100 mW的输出功率以及50 GHz的调谐带宽。输出功率在370.5 GHz频点处处达到峰值2.3 W,电子注电压7.0 kV,注电流120 mA,聚焦磁场1.0 T。 相似文献
3.
利用2维半全电磁PIC程序进行数值模拟,设计了一种C波段磁绝缘线振荡器。该振荡器在阴极电子发射起点加圆环,控制此处电子束的发射密度,来减少电子能量的损耗,改善束-波互作用;逐渐加大慢波结构的后两个叶片的内半径,增大微波群速度,便于谐振腔中的能量输出,提高微波输出效率;采用两个扼流片有效地阻止了微波功率向二极管区泄漏,相应减小了器件的尺寸。当外加电压为430 kV、束流46 kA时,饱和后输出微波平均功率2 GW,频率3.51 GHz,功率转换效率10%。 相似文献
4.
针对当前高功率微波(HPM)中的热点器件磁绝缘线振荡器(MILO) 频率低、效率低等问题,提出了一种可以沿x方向平面展开的平面MILO。该器件也是一种低阻抗高功率微波器件,通过一个低外加磁场来代替常规MILO中的磁绝缘电流,辅助实现器件的磁绝缘,从而实现器件效率的提高。结合PIC模拟,建立一个外加低磁场的C波段平面MILO,并根据其慢波结构(平面折绉表面)特点给出相应的色散曲线,确定微波器件工作点,利用2.5维全电磁粒子模拟软件对其进行数值模拟,在输入为4.0 GW电功率(工作电压约800 kV)的条件下,模拟得到频率为6.56 GHz的微波输出,通过优化外加磁场,使得模拟微波输出功率达到1.22 GW,功率效率在C波段条件下超过30%。 相似文献
5.
6.
7.
8.
9.
Based on the combination of a staggered double vane slow wave structure(SWS) and round electron beam,a 200-W W-band traveling-wave tube(TWT) amplifier is studied in this paper.The main advantages of round beam operation over the sheet beam is that the round beam can be formed more easily and the focus requirement can be dramatically reduced.It operates in the fundamental mode at the first spatial harmonic.The geometric parameters are optimized and a transition structure for the slow wave circuit is designed which can well match the signal that enters into and goes out from the tube.Then a TWT model is established and the particle-in-cell(PIC) simulation results show that the tube can provide over 200-W output power in a frequency range of 88 GHz-103 GHz with a maximum power of 289 W at 95 GHz,on the assumption that the input power is 0.1 W and the beam power is 5.155 kW.The corresponding conversion efficiency and gain at 95 GHz are expected to be 5.6% and 34.6 dB,respectively.Such amplifiers can potentially be used in high power microwave-power-modules(MPM) and for other portable applications. 相似文献
10.
提出采用圆形电子注和双排矩形梳状慢波结构作为W波段宽频带行波管注波互作用回路. 对该慢波回路的"冷"态特性、输入输出结构等方面进行了模拟仿真和分析, 研究结果表明, 该结构色散特性较好, 带宽较宽; 通过调整双排矩形梳状慢波结构之间的距离和电子注通道半径的尺寸, 圆形电子注系统取得了和带状注系统相同的耦合阻抗; 且该结构传输特性较好, 优化后整管的驻波比能在较宽的频带内保持在2以下. 此外, 对该慢波系统的大信号理论计算和PIC粒子模拟结果一致. 在50 mW驱动功率下, 输出功率在10 GHz带宽内大于40 W, 增益高于29 dB. 相似文献
11.
为了便于模式变换器的设计,达到双频微波都能集中辐射的目的,提出一种轴向分区的双频磁绝缘线振荡器,该器件束波互作用区为中间隔开、两端不同周期、不同深度的慢波结构,使电子在上下游与不同频率特性的慢波结构进行束波互作用,得到稳定的双频微波输出。使用2.5维全电磁粒子模拟软件进行数值模拟,在工作电压450 kV,电流40 kA条件下输出微波功率为1.4 GW,功率效率约为7%,输出的微波频率分别为1.25 GHz和1.65 GHz,两者频谱幅度相差约为1.5 dB,模式为TEM模。 相似文献
12.
提出了一种新型的慢波结构—-V形曲折矩形槽慢波结构, 该结构是由矩形槽波导沿其E面法向周期性呈V形折叠而成, 其两金属板之间的间隙形成天然的带状电子注通道. 相比传统的U形曲折矩形槽波导, 它能在保持良好高频特性的情况下增加互作用面积, 从而可以采用面积更大的带状电子注以获得更大的输出功率. 分析了该结构的高频特性, 在V波段完成了对行波管互作用电路的设计, 并利用三维粒子模拟的方法估计了其工作性能. 研究结果表明, 当工作电压和电流分别为12.8 kV和600 mA 时, 在58—64 GHz的频率范围内饱和平均输出功率大于1000 W, 相应的饱和增益和电子效率分别大于33 dB和13.2%. 相似文献
13.
设计了一种能在C波段和X波段实现稳定双频输出的带有非对称谐振反射腔的单电子束同轴相对论返波振荡器。采用耦合阻抗跃变型慢波结构,使用粒子PIC模拟软件进行了粒子模拟研究。模拟结果显示:轴向电场在系统中的分布得到改进,电子束的能散得到改善。在电子束电压511 kV,电流8.95 kA,引导磁场0.73 T的条件下,双频器件实现了8.09 GHz和9.91 GHz的双波段频率稳定输出,平均功率为1.0 GW,波束互作用效率为21.9%, 效率高于空心双波段返波管及其他双波段器件。器件辐射功率的拍频为1.82 GHz,拍波更为明显和稳定。模拟研究中同时发现, 随着慢波结构之间漂移段的变化,双频频率都呈现一种准周期的变化。 相似文献
14.
15.
脊加载螺旋槽行波管是一类新型毫米波大功率器件,给出了此结构中引入电子注后的“热”色散方程,并利用“牛顿”下山法求解了此复系数超越方程.通过数值计算给出了一个工作电压为20kV频率为474GHz的脊棱加载慢波结构的具体尺寸,并对此结构中小信号增益随脊尺寸的变化情况及电子注参数对其影响进行了研究,计算结果表明:此结构适宜于作为高增益窄带毫米波大功率行波管的慢波线,其3dB增益带宽为34%;为了展宽其工作带宽,可以适当减小间隙宽度,也可在一定范围内提高电子注电流.给出的理论对于研制此类行波管具有一定的指导意
关键词: 相似文献
16.
A novel slow-wave structure (SWS), the folded double-ridged waveguide structure, is presented and its linear gain properties are investigated. The perturbed dispersion equation is derived and the small signal growth rate is calculated for dimensions of the ridge-loaded region and the parameters of the electron beam. The novel structure has potential applications in the production of high power and broad band radiation. For a cold beam, the linear theory predicts a gain of 1.1-1.27dB/period and a 3-dB small-signal gain bandwidth of 30% in W-band. A comparison between the folded double-ridged waveguide SWS and folded waveguide SWS (FWSWS) shows that with the same physical parameters, the novel SWS has an advantage over the FWSWS on the bandwidth and electron efficiency. 相似文献
17.
18.
19.
A high-power subterahertz surface wave oscillator with separated overmoded slow wave structures 下载免费PDF全文
A megawatt-level subterahertz surface wave oscillator(SWO) is proposed to obtain high conversion efficiency by using separated overmoded slow wave structures(SWSs). Aiming at the repetitive operation and practical applications, the device driven by electron beam with modest energy and current is theoretically analyzed and verified. Then,the functions of the two SWS sections and the effect of the drift tube are investigated by using a particle-in-cell code to reveal how the proposed device achieves high efficiency. The mode analysis of the beam-wave interaction region in the device is also carried out, and the results indicate that multi-modes participate in the premodulation of the electron beam in the first SWS section, while the TM01 mode surface wave is successfully and dominantly excited and amplified in the second SWS section. Finally, a typical simulation result demonstrates that at a beam energy of 313 ke V, beam current of 1.13 k A, and guiding magnetic field of above 3.5 T, a high-power subterahertz wave is obtained with an output power of about 70 MW at frequency 146.3 GHz, corresponding to the conversion efficiency of 20%. Compared with the results of the previous subterahertz overmoded SWOs with integral SWS and similar beam parameters, the efficiency increases almost 50% in the proposed device. 相似文献
20.